Development of an Analytical Method Based on Accelerated Solvent Extraction, Solid-Phase Extraction Clean-Up, then GC–ECD for Analysis of Fourteen Organochlorine Pesticides in Cereal Crops

A method has been developed for analysis of 14 organochlorine pesticide residues in cereals. After accelerated solvent extraction and solid-phase extraction clean-up on graphitized carbon black/primary–secondary amine (GCB/PSA), to reduce co-extraction of interferences, pesticide residues were analyzed by gas chromatography with electron-capture detection. When the method was validated, recoveries were in the range 78–116%, relative standard deviations were in the range 1.1–16.3%, and limits of detection and quantification were from 1.5 to 4.2 μg kg^?1 and from 4.6 to 12.5 μg kg^?1, respectively.     

QuEChERS and solid phase extraction methods for the determination of energy crop pesticides in soil,plant and runoff water matrices

QuEChERS and solid phase extraction (SPE) methods were applied for determining four herbicides (metazachlor, oxyfluorfen, quizalofop-p-ethyl, quinmerac) and one insecticide (α(±)-cypermethrin) in runoff water, soil, sunflower and oilseed rape plant matrices. Determination was performed using gas chromatography mass spectrometry (GC-MS), whereas high-pressure liquid chromatography mass spectrometry (HPLC-MS) was used for quinmerac. In all substrates linearity was evaluated using matrix-matched calibration samples at five concentration levels (50–1000 ng L^?1 for water, 5–500 μg kg^?1 for soil and 2.5–500 μg kg^?1 for sunflower or oilseed rape plant). Correlation coefficient was higher than 0.992 for all pesticides in all substrates. Acceptable mean recovery values were obtained for all pesticides in water (65.4–108.8%), soil (70.0–110.0%) and plant (66.1–118.6%), with intra- and inter-day RSD% below 20%. LODs were in the range of 0.250–26.6 ng L^?1 for water, 0.10–1.8 μg kg^?1 for soil and 0.15–2.0 μg kg^?1 for plants. The methods can be efficiently applied for field dissipation studies of the pesticides in energy crop cultivations.     

A sensitive and specific ELISA for determining a residue marker of three quinoxaline antibiotics in swine liver

Methyl-3-quinoxaline-2-carboxylic acid (MQCA) is a possible residue marker for three quinoxaline veterinary medicines (olaquindox, mequindox, and quinocetone). The wide application of mequindox/quinocetone or the illegal use of olaquindox leads to MQCA residue in animal’s original food, thereby threatening the safety of human food. The indirect competitive enzyme-linked immunosorbent assay (IC-ELISA) with a specific coating antigen and monoclonal antibody (MAB) was established and optimized for detecting MQCA in swine liver. Samples were acidified with 2 mol?l^?1 hydrochloric acid, extracted with ethyl acetate–hexane–isopropanol (8?+?1?+?1, v/v/v) and then detected by IC-ELISA. The logarithm correlation of standards to OD values ranged from 0.2 to 200 μg?l^?1, with IC₅₀ of 6.46 μg?l^?1. Negligible cross-reactivity happened to five quinoxaline antibiotics (olaquindox, mequindox, quinocetone, carbadox, and cyadox) and the metabolite of carbadox and cyadox (quinoxaline-2-carboxylic acid). When spiked with 1 to 100 μg?kg^?1 of MQCA, the recoveries ranged from 85.44 to 100.02 %, with the intra-assay coefficient of variation (CV) of 6.64–10.57 % and inter-assay CV of 7.29–10.88 %. The limit of detection for MQCA was 1.0 μg?kg^?1 in swine liver. Furthermore, incurred samples were detected by the IC-ELISA and then conformed by a reported LC/MS/MS method, it shown that there was good correlation between the two methods. All these results indicated that the IC-ELISA method is appropriate for surveillance MQCA residue in animal tissues.

Development and validation of a (semi-)quantitative UHPLC-MS/MS method for the determination of 191 mycotoxins and other fungal metabolites in almonds, hazelnuts, peanuts and pistachios

A multi-target method for the determination of 191 fungal metabolites in almonds, hazelnuts, peanuts and pistachios was developed. The method includes all mycotoxins regulated in the European Union and mycotoxins regularly found in food. After extraction with an acidified acetonitrile water mixture, the raw extract was diluted and injected directly into the UHPLC-MS/MS system. In two chromatographic runs, analysis was performed in positive and in negative ionisation mode. The method was in-house validated for the most important 65 analytes in these four commodities. Apparent recoveries between 80 and 120 % were obtained for about half of the analyte–matrix combinations. Good repeatabilities (standard deviations?<?10 %) were achieved for the vast majority (83 %) of all cases. Only in 6 % of all combinations did the standard deviations exceed 15 %. Matrix effects, arising during electrospray ionisation, significantly influenced the determination. For instance, signal suppression was observed for several early-eluting analytes and also signal enhancement up to 295 % for physcion in peanuts was determined. Concerning extraction recovery, 94 % of the analyte–matrix combinations showed values higher than 50 %. Lower limits of quantification ranged between 0.04 μg?kg^?1 for enniatin B3 in peanuts and 500 μg?kg^?1 for HC toxin in hazelnuts. Additionally, the applicability of the developed method was demonstrated through the analysis of 53 naturally contaminated nut samples from Austria and Turkey. Overall, 40 toxins were quantified; the most frequently found mycotoxins were beauvericin (79 %), enniatin B (62 %) and macrosporin (57 %). In the most contaminated hazelnut sample, 26 different fungal metabolites were detected.     

SPE–LC Multi-Residue Analysis of Mebendazole and its Metabolites in Grass Carp and Shrimp

An analytical method was developed to detect the residue of mebendazole and its metabolites (hydroxymebendazole and aminomebendazole) in the muscle of grass carp and shrimp by LC–UV detection. Mebendazole and its metabolites were extracted with water and ethyl acetate, defatted with hexane, and purified with MCX solid phase extraction column. The intra- and inter-batch precision (measured by CV%) was <9.0%. The accuracy (measured by relative error, %) was <12%. The LODs were 2.5 μg kg^?1 for mebendazole and hydroxymebendazole, 5 μg kg^?1 for aminomebendazole; the LOQs were 5 μg kg^?1 for mebendazole and hydroxymebendazole, 10 μg kg^?1 for aminomebendazole. The mean recoveries of mebendazole and its metabolites from grass carp and shrimp muscle at a concentration range of 5.0–500.0 μg kg^?1 were 90.7–97.0% with relative standard deviations below 10%.     

Water-based slow injection ultrasound-assisted emulsification microextraction for the determination of deoxynivalenol and de-epoxy-deoxynivalenol in maize and pork samples

A novel water-based slow injection ultrasound-assisted emulsification microextraction (SI-USAEME) method followed by ultra-high performance liquid chromatography-tandem mass spectrometry analysis was developed for the rapid pretreatment and determination of deoxynivalenol (DON) and its metabolite, de-epoxy-deoxynivalenol (DOM-1), in maize and pork samples. After optimization, the method recoveries for DON and DOM-1 ranged from 73 to 85 % with intraday and interday variations less than 9.4 and 9.2 %, respectively. The limits of detection for DON were 4.2 μg?kg^?1 in maize and 6.2 and 5.9 μg?kg^?1 for DON and DOM-1, respectively, in pork. In addition, an immunoaffinity column (IAC) was prepared. A study comparing the IAC cleanup method, the solid-phase extraction (SPE) cleanup method, and the proposed SI-USAEME method was presented. The water-based SI-USAEME method could become a simple, low-cost alternative to the conventional IAC and SPE method. The method was successfully applied to the analysis of commercial maize and pork products.     

Determination of Chloramphenicol Residues in Foods by ELISA and LC-MS/MS Coupled with Molecularly Imprinted Solid Phase Extraction

The combination of molecularly imprinted solid-phase extraction (MISPE) with ELISA and LC-MS/MS was developed for the detection of chloramphenicol (CAP) in honey samples. Significant recoveries of 99.1 ± 7.1 and 98.8 ± 8.2% were obtained for intra- and inter-assay determination by ELISA determination, respectively. The limit of detection of CAP was 0.034 μg kg^?1 and the limit of quantification was 0.046 μg kg^?1. Determination and validation of CAP by using LC-MS/MS were performed following the same extraction and purification process as for the ELISA. The results demonstrated that the CAP samples purified by using MISPE were simultaneously applicable to analysis by ELISA and LC-MS/MS.     

Determination of Melamine in Food by SPE and CZE with UV Detection

A novel method for the determination of melamine residue in food was developed using solid-phase extraction and capillary zone electrophoresis with UV detection. Spiked samples were extracted with 1% trichloroacetic acid while 0.03 g sodium deoxycholate was used to precipitate protein in the real samples. After centrifuging and clean-up by solid-phase extraction cartridge, the extract was directly analyzed by CZE–UV. The method was validated and good results were obtained with respect to precision, repeatability and spiked recovery. The limit of detection for melamine varied between 0.25 and 0.5 mg kg^?1. The proposed method was successfully applied for the analysis of melamine in food with total recoveries ranging from 94 to 102% in the spiked range of 0.5–5 mg kg^?1, and the relative standard deviations were between 1.5 and 4.1%.     

Determination of twelve herbicides in tobacco by a combination of solid–liquid–solid dispersive extraction using multi-walled carbon nanotubes, dispersive liquid-liquid micro-extraction, and detection by GC with triple quadrupole mass spectrometry

We report on a method for the determination of twelve herbicides using solid–liquid–solid dispersive extraction (SLSDE), followed by dispersive liquid-liquid micro-extraction (DLLME) and quantitation by gas chromatography with triple quadrupole mass spectrometric detection. SLSDE was applied to the extraction of herbicides from tobacco samples using multi-walled carbon nanotubes (MWCNTs) as clean-up adsorbents. The effect of the quantity of MWCNTs on SLSDE, and of type and volume of extraction and disperser solvents and of salt effect on DLLME were optimized. Good linearity is obtained in the 5.0 - 500 μg kg^?1 concentration range, with regression coefficients of >0.99. Intra-day and inter-day repeatability, expressed as relative standard deviations, are between 3 and 9 %. The recoveries in case of herbicide-spiked tobacco at concentration levels of 20.0, 50.0 and 100.0 g kg^?1 ranged from 79 to 105 %, and LODs are between 1.5 and 6.1 μg kg^?1. All the tobacco samples were found to contain butralin and pendimethalin at levels ranging from 15.8 to 500.0 μg kg^?1.

Hybrid flow analyzer for automatic hollow-fiber-assisted ionic liquid-based liquid-phase microextraction with in-line membrane regeneration

The proof-of-concept of a new methodology for in-line hollow-fiber (HF)-assisted three-phase liquid-phase microextraction (LPME) allowing for handling of the feed and acceptor aqueous solutions and of minute volumes of the organic extracting phase in a programmable flow mode is reported in this paper. The flow analyzer fosters in-line anchoring of ionic-liquid-laden extracting solution (10 % (v/v) methyltrioctyl ammonium chloride in kerosene) in the pores of a single-strand microporous polypropylene HF, and regeneration of the liquid-phase membrane itself for each individual analysis cycle in a fully automated mode. Using hexavalent chromium as a model analyte and 1,5-diphenylcarbazide as a chromogenic probe in the acceptor solution, the flow-based HF-LPME hyphenated system was harnessed to the clean-up of troublesome samples (viz., domestic wastewater and soil leachates) with concomitant enrichment of target species. Distinct extraction modes and chemistries were assessed for enhanced Cr(VI) permeability. A single sample plug was subjected to a twofold backward–forward flow extraction so as to decrease the thickness of the boundary layer at the HF shell side for improved extraction efficiency. Under the optimized physicochemical variables, a limit of detection of 4.6 μg?L^?1 Cr(VI), a dynamic linear range of up to 500 μg?L^?1 and intermediate precision better than 10 % were obtained for a sample volume of 2.8 mL buffered at pH 4 and a volume of organic extractant of 120 μL, with an enrichment factor of ca. 11 for a sample residence time in the donor compartment of merely 4.5 min. Analyte recoveries in domestic wastewaters were ≥83 % using external calibration with relative standard deviations better than 14 %, thereby demonstrating the expedient clean-up of samples with elevated content of dissolved organic carbon. The automatic HF-LPME method was validated in terms of bias against the SRM 2701 (NIST soil) preceded by the EPA alkaline digestion method 3060A. No significant differences between Cr(VI) concentration as obtained with the automatic HF-LPME system (546?±?57 mg?kg^?1) and the certified value (551.2?±?17.2 mg?kg^?1, expressed as mean ± combined uncertainty) were encountered at the 0.05 significance level.     

Simultaneous determination of sulfonamides and metabolites in manure samples by one-step ultrasound/microwave-assisted solid–liquid–solid dispersive extraction and liquid chromatography–mass spectrometry

An in-line matrix cleanup method was used for the simultaneous extraction of 15 sulfonamides and two metabolites from manure samples. The ultrasound/microwave-assisted extraction (UMAE) combined with solid–liquid–solid dispersive extraction (SLSDE) procedure provides a simple sample preparation approach for the processing of manure samples, in which the extraction and cleanup are integrated into one step. Ultrasonic irradiation power, extraction temperature, extraction time, and extraction solvent, which could influence the UMAE efficiency, were investigated. C₁₈ was used as the adsorbent to reduce the effects of interfering components during the extraction procedure. The extracts were concentrated, and the analytes were analyzed by liquid chromatography–tandem mass spectrometry (LC–MS/MS) without any further cleanup. The isotopically labeled compounds sulfamethoxazole-d ₄, sulfamethazine-d ₄, sulfamonomethoxine-d ₄, and sulfadimethoxine-d ₆ were selected as internal standards to minimize the matrix effect in this method. The recoveries of the antibiotics tested ranged from 71 to 118 % at the three spiking levels examined (20, 200, and 500 μg?·?kg^-1). The limits of detections were 1.2–3.6 μg?·?kg^-1 and the limits of quantification were 4.0–12.3 μg?·?kg^-1 for the sulfonamides and their metabolites. The applicability of the method was demonstrated by analyzing 30 commercial manure samples. The results indicated that UMAE–SLSDE combined with LC–MS/MS is a simple, rapid, and environmentally friendly method for the analysis of sulfonamides and their metabolites in manure, and it could provide the basis for a risk assessment of the antibiotics in agricultural environments.     

Use of a Headspace Solid-Phase Microextraction-Based Methodology Followed by Gas Chromatography–Tandem Mass Spectrometry for Pesticide Multiresidue Determination in Teas

This study reports on the development of a fast and efficient method based on headspace solid-phase microextraction (HS-SPME) coupled to gas chromatography–tandem mass spectrometry (GC–MS/MS) for simultaneous analysis of 128 volatile or semi-volatile pesticide residues belonging to nine classes of pesticides. The important factors related to HS-SPME performance were optimized; these factors include fiber types, water volume, ion strength, extraction temperature, and extraction time. The best extraction conditions include a PDMS/DVB fiber, and analytes were extracted at 90 °C for 60 min from 1 g of tea added to 5 mL of 0.2 g mL^?1 NaCl solution. The methodology was validated using tea samples spiked with pesticides at three concentration levels (10, 50, and 100 μg kg^?1). In green tea, oolong tea, black tea, and puer tea, 82.8, 88.3, 79.7, and 84.3% of the targeted pesticides meet recoveries ranging from 70 to 120% with a relative standard deviation of?≤?20%, respectively, when spiked at a level of 10 μg kg^?1. Limits of quantification in this method for most of the pesticides were 1 or 5 μg kg^?1, which are far below their maximum residue limits prescribed by EU. The optimized method was employed to analyze 30 commercial samples obtained from local markets; 17 pesticide residues were detected at concentrations of 2–452 μg kg^?1. Chlorpyrifos was the most detected pesticide in 80% of the samples, and the highest concentration of dicofol (452 μg kg^?1) was found in a puer tea. This is the first time to find that the optimized extraction temperature for pesticide residues is 90 °C, which is much higher than other reported HS-SPME extraction conditions in tea samples. This developed method could be used to screen over one hundred volatile or semi-volatile pesticide residues which belong to multiple classes in tea samples, and it is an accurate and reliable technique.     

Residues and dissipation of guadipyr in rice ecological system

A modified QuEChERs method with liquid chromatography-tandem mass spectrometry for analysis of guadipyr residue and dissipation in rice matrices, paddy soil and paddy water was developed and validated. Mean recoveries and relative standard deviations in paddy soil, paddy water, rice plant, rice straw, rice hull and husked rice matrices at three spiking levels were 83.1–116.5% and 1.6–9.5%, respectively. The half-life of guadipyr was determined in 2 years at three different field sites in China via a dissipation experiment. The half-lives of guadipyr in paddy water were 0.22–0.37 days, 0.24–3.33 days in paddy soil and 0.44–1.90 days in rice plant. The terminal residues of guadipyr ranged from ND (concentrations of guadipyr were below limit of detection) to 50 μg kg^?1 in paddy soil, 10–470 μg kg^?1 in rice hull, ND70 μg kg^?1 in husked rice and ND to 110 μg kg^?1 in rice straw. The results would be helpful in fixing maximum residue limit of guadipyr, a new insecticide, in rice.     

Application of Dispersive Liquid�CLiquid Microextraction for the Analysis of Six Fungicides in Fruit Samples by GC�CECD

A novel approach for the determination of six fungicides (triadimefon, procymidone, hexaconazole, myclobutanil, diniconazole and iprodione) in fruit samples is presented. Analytes were extracted using the dispersive liquid?Cliquid microextraction technique and determined by GC?CECD. Parameters affecting the dispersive liquid?Cliquid microextraction performance, such as the kind and volume of extraction and dispersive solvents, extraction time and salt concentration, were studied and optimized. Under the optimum extraction conditions, the linearities of the method were obtained in the range of 0.5?C20.0 ??g kg^?1 for triadimefon, hexaconazole, diniconazole and procymidone, and 1.0?C40.0 ??g kg^?1 for myclobutanil and iprodione, with the correlation coefficients ranging from 0.9902 to 0.9995. The enrichment factors ranged from 685 to 820 and the extraction recoveries ranged from 81.3 to 98.4%. The relative standard deviations varied from 3.1 to 7.8%. The limits of detection of the method were in the range of 0.02?C0.12 ??g kg^?1. Results showed that the method we proposed can meet the requirements for the determination of target fungicides in fruit samples. Several compounds considered in this study were found in fruit samples.     

Dissipation dynamics of fenamidone and propamocarb hydrochloride in pepper,soil and residue analysis in vegetables by ultra-performance liquid chromatography coupled with tandem mass spectrometry

In this study, a rapid and sensitive method was developed for determining fenamidone and propamocarb hydrochloride residues in vegetables and soil by ultra-performance liquid chromatography-tandem mass spectrometry. The dissipation dynamics of fenamidone and propamocarb hydrochloride in pepper and soil was investigated in Beijing, Henan and Shandong provinces. The target compounds were extracted with methanol and cleaned with dispersive solid phase extraction using primary secondary amine. Two pairs of precursor product ion transitions for fenamidone and propamocarb hydrochloride were measured and evaluated. Average recoveries of fenamidone in potato, tomato, cabbage, pepper and soil at three levels (10, 100 and 1000 μg kg^?1) ranged from 76.91% to 107.31% with relative standard deviations (RSDs) from 2.74% to 10.87% (n = 15). The average recoveries of propamocarb hydrochloride ranged from 74.84% to 97.96% with RSDs from 2.43% to 16.16% (n = 15). The limits of detection (LODs) for fenamidone in each matrix were 0.131–0.291 μg kg^?1, and the limits of quantification (LOQs) were 0.436–0.970 μg kg^?1. The LODs for propamocarb hydrochloride were 0.125–0.633 μg kg^?1, and the LOQs were 0.417–2.11 μg kg^?1. The results also showed that the dissipation of fenamidone and propamocarb hydrochloride in pepper and soil followed first-order kinetics model more than that of bi-exponential models. The half-lives of propamocarb hydrochloride were 6.90–15.78 days in pepper and 13.56–23.02 days in soil. The half-lives of fenamidone were 7.48–11.29 days in pepper and 35.18–42.78 days in soil.     

Fast and Selective Pressurized Liquid Extraction with Simultaneous In-Cell Cleanup for the Analysis of Ethyl Carbamate in Fermented Solid Foods

A novel analytical methodology that could be used to identify ethyl carbamate (EC) in fermented solid foods was developed and validated. The method was based on selective pressurized liquid extraction with a simultaneous in-cell cleanup combined with gas chromatography–tandem mass spectrometry. The final method was performed at 50 °C for 2 × 5 min using ethyl acetate. Florisil was placed inside the extraction cell downstream of the sample to remove interfering compounds. The proposed method showed a limit of detection of 0.3 μg kg^?1 and a limit of quantitation of 1.0 μg kg^?1. The recoveries ranged from 98 to 107 % with relative standard deviations of <7 %. The validated method was successfully applied for the determination of EC in French bread, sauerkraut and fermented bead curd samples.     

Determination of Nicotine in Dried Mushrooms by Using a Modified QuEChERS Approach and GC–MS–MS

Levels of nicotine higher than the maximum residue level were detected in edible mushrooms. Analyses of self-collected and purchased dried mushrooms were performed with a QuEChERS approach. A small amount (2.5 g) of dried sample matrix was mixed with 5 mL sodium hydroxide solution, 2.5 g of sodium sulfate/sodium chloride mixture (4:1) and 5 mL ethyl acetate. The organic phase was cleaned by using dispersive solid-phase extraction and analysed by GC–MS–MS. The linear range of the method was 0.01–10.00 mg kg^?1 and the limit of detection 0.006 mg kg^?1 on dry weight basis by using EURACHEM method.     

Validation of QuEChERS-based UPLC-MS/MS method for determination of quinoid niclosamide (LDS) residue in water,soil and rice samples

A sensitive, rapid and easy analytical method was validated for the determination of quinoid niclosamide (LDS) molluscicide in water, rice and soil using a QuEChERS extraction procedure and ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) detection. The LDS was extracted by using acetonitrile and then cleaned up by using dispersive solid-phase extraction with florisil and C18 sorbents. The determination of the target compound was achieved in less than 3 min using an electrospray ionisation source in negative mode. The overall average recoveries for this method in water, rice and soil matrix at three fortified levels ranged from 82.54 to 99.9%, with relative standard deviations in the range of 1.51 to 4.86% (n = 5). The calculated limits of detection were lower than 0.1 µg kg^?1 and quantification was 5 µg kg^?1; these values were much lower than the maximum residue levels established by the Australian standard (0.01 mg kg^?1). The results of the method validation confirmed that this proposed method is convenient and reliable for the determination of LDS molluscicide in water, rice and soil samples.     

HPLC Analysis and Pharmacokinetic Study of Paeoniflorin after Intravenous Administration of a New Frozen Dry Powder Formulation in Rats

A simple and specific high performance liquid chromatographic (HPLC) method with UV detection using picroside II as the internal standard was developed and validated to determine the concentration of paeoniflorin in rat plasma and study its pharmacokinetics after an single intravenous administration of 40 mg kg^?1 paeoniflorin to Wistar rats. The analytes of interest were extracted from rat plasma samples by ethyl acetate after acidification with 0.05 mol L^?1 NaH₂PO₄ solution (pH 5.0). Chromatographic separation was achieved on an Agilent XDB C₁₈ column (250 × 4.6 mm I.D., 5 μm) with a Shim-pack GVP-ODS C₁₈ guard column (10 × 4.6 mm I.D., 5 μm) using a mobile phase consisting of acetonitrile–water–acetic acid (18:82:0.4, v/v/v) at a flow rate of 1.0 mL min^?1. The UV detection was performed at a wavelength of 230 nm. The linear calibration curves were obtained in the concentration range of 0.05–200.0 μg mL^?1 in rat plasma with the lower limit of quantification (LLOQ) of 0.05 μg mL^?1. The intra- and inter-day precisions in terms of % relative standard deviation (RSD) were lower than 5.7 and 8.2% in rat plasma, respectively. The accuracy in terms of % relative error (RE) ranged from ?1.9 to 2.6% in rat plasma. The extraction recoveries of paeoniflorin and picroside II were calculated to be 69.7 and 56.9%, respectively. This validated method was successfully applied to the pharmacokinetic study of a new paeoniflorin frozen dry power formulation. After single intravenous administration, the main pharmacokinetic parameters t _1/2, AUC_0-∞, CL_TOT, V _Z, MRT_0-∞ and V _ss were 0.739 ± 0.232 h, 43.75 ± 6.90 μg h mL^?1, 15.50 ± 2.46 L kg^?1 h^?1, 1.003 ± 0.401 L kg^?1, 0.480 ± 0.055 h and 0.444 ± 0.060 L kg^?1, respectively.     

Optimised accelerated solvent extraction of PCBs and PAHs from compost

This study is the first thorough method optimisation for accelerated solvent extraction (ASE) of polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs) from chemically dried compost. For PCBs, optimised solvent composition, temperature, pressure, number of static cycles, duration, and flush volume were as follows: toluene/acetone 1?:?3 (v/v), 120°C, 2000?psi, 3?×?5?min, and 50%, respectively. Limits of quantification and method precision were between 0.16 and 2.46?µg?kg^?1 dw and 6–17% respectively for individual PCBs. Absolute recoveries of isotope-labelled extraction standards used for each of the analytes ranged from 65 to 105% and relative recoveries were between 85 and 99%. The method proofed to be robust and was successfully applied to different compost samples.

The optimisation of PAHs extraction was performed and resulted in the following conditions: solvent: hexane/acetone 1/3 (v:v), temperature: 140°C, pressure: 1500?psi, extraction time: 3?×?5?min, and 50% flush volume. Limits of detection and method precision for individual PAHs were between 1.1 and 37.2?µg?kg^?1?dw and 12–34% respectively. Absolute and relative recoveries ranged from 24 to 68% and from 85 to 99%, respectively. Optimal extraction conditions for PAHs were more difficult to determine due to the inhomogeneous distribution of PAHs in samples. However, the method appeared to be feasible and suggestions for further improvements are presented.