Preparation of an efficient nanofiltration membrane based on blending of polysulfone and polysulfone-g-butylacrylate prepared by ATRP

Polysulfone is one of the most common used polymers for preparation of nanofiltration membranes. These membranes are highly susceptible to fouling problems because of their surface hydrophobic nature. In this paper a new approach for modification of polysulfone to overcome the fouling problems was introduced. The modification was carried out via blending of polysulfone with a modified grafted polysulfone using atom transfer radical polymerization (ATRP) method. The modified grafted polysulfone was synthesized via ATRP grafting of n-butylacrylate from chloromethylated polysulfone. The graft copolymers were characterized by FT-IR, NMR, DSG and TGA techniques. Furthermore, surface morphology and performance of the corresponding membrane were studied in detail using SEM and pure water flux and salt rejection experiments, respectively. The results indicated that the prepared modified polysulfone membranes have high surface hydrophilicity and therefore better fouling resistance and very good water permeability.     

Melt miscibility of HDPE/UHMWPE,LDPE/UHMWPE,and LLDPE/UHMWPE blends detected by dynamic rheometer

The dynamic rheological behavior of high density polyethylene (HDPE)/ultrahigh molecular weight polyethylene (UHMWPE) blends, low density polyethylene (LDPE)/UHMWPE blends and linear low density polyethylene (LLDPE)/ UHMWPE blends was measured in parallel plate rheometer at 200°C. The analysis of log-additivity rule, Cole-Cole plots and Han curves of the three series blends indicated that the LDPE/UHMWPE blends were miscible in the melt, while the HDPE/UHMWPE blends and LLDPE/UHMWPE blends showed phase separation. The DSC results of LLDPE/UHMWPE blends and HDPE/UHMWPE blends were consistent with the rheological properties, while for the thermal properties of LDPE/UHMWPE blends, results revealed three endothermic peaks, which indicated a liquid-solid phase separation in LDPE/UHMWPE blends.     

Graft copolymers via combination of cationic polymerization and atom transfer radical polymerization and their phase separation into spherical/worm-like nanostructures

Poly(p-chloromethyl styrene)-graft-poly(methyl methacrylate) (PCMS-g-PMMA) and poly(p-chloromethyl styrene)-graft-poly(benzyl methacrylate) (PCMS-g-PBzMA) graft copolymers with asymmetric branches are synthesized via the combination of cationic polymerization and atom transfer radical polymerization (ATRP). The process involves first, the preparation of poly(p-chloromethyl styrene) (PCMS-CH₂Cl) macroinitiator without any cross-linking or side reactions through pendant benzyl chloride (?CH₂Cl) functionality by cationic polymerization using a simple FeCl₃-based initiating system at 25 °C. The as-synthesized PCMS-CH₂Cl, without any transformation, is then used as the macroinitiator to graft PMMA and PBzMA branches by ATRP to produce PCMS-g-PMMA and PCMS-g-PBzMA graft copolymers of varying compositions with controlled molecular weight and moderately narrow polydispersities (M _w/M _n?≤?1.32). The resulting PCMS₂₁ -g-PMMA₂₃₂ graft copolymer in thin film form phase separates into spherical morphology with an average diameter of 170?±?72 nm. Whereas the PCMS₂₁ -g-PBzMA₁₅₆ graft copolymer gives worm-like nanostructures with an average length of 94 nm and width of 31 nm due to phase separation as visualized through atomic force microscopy. On the other hand, the phase-separated morphology is not very well-defined for other graft copolymers (PCMS₁₁₃ -g-PMMA₂₂₇ and PCMS₁₁₃ -g-PBzMA₁₅₄) thin films containing longer PCMS chains. This approach represents a rapid and convenient route to prepare unique spherical/worm-like polymer nanostructures. Figure

Well-defined poly(p-chloromethyl styrene)-graft-poly(methyl methacrylate) (PCMS-g-PMMA) and poly(p-chloromethyl styrene)-graft-poly(benzyl methacrylate) (PCMS-g-PBzMA) graft copolymers with asymmetric branches are synthesized by the combination of living cationic polymerization and atom transfer radical polymerization (ATRP). The resulting PCMS₂₁ -g-PMMA₂₃₂ and PCMS₂₁ -g-PBzMA₁₅₆ graft copolymers phase separate into nanostructured spherical and worm-like morphologies, respectively, in thin film form. The phase-separated morphology is not very well-defined for graft copolymers (PCMS₁₁₃ -g-PMMA₂₂₇ and PCMS₁₁₃ -g-PBzMA₁₅₄) thin films containing longer PCMS chains.     

Thermally stimulated discharge current (TSDC) characteristics in β-phase PVDF–BaTiO3 nanocomposites

β-phase polyvinylidene fluoride (PVDF)–BaTiO₃ nanocomposite samples have been prepared by solution mixing method. XRD data represent that the crystallinity of PVDF decreases with increase in loading level of BaTiO₃ nanoparticles. DSC curve represents that the melting point of PVDF is lightly affected by loading concentration of BaTiO₃. The morphology and microstructure of PVDF and PVDF embedded by BaTiO₃ nanofillers were investigated by using inverted contrast microscopy (ICM) and scanning electron microscopy (SEM). FTIR interferrometry is proven that PVDF and BaTiO₃ are not chemically interacting; therefore, interaction of BaTiO₃ is van der Waals type of interaction. The thermally stimulated discharge current (TSDC) of PVDF and PVDF–BaTiO₃ nanocomposites sample was characterized by single peak. The observed TSDC peak is discussed on the basis of dipolar and interfacial polarization.     

A wide range optical pH sensor for living cells using Au@Ag nanoparticles functionalized carbon nanotubes based on SERS signals

p-Aminothiophenol (pATP) functionalized multi-walled carbon nanotubes (MWCNTs) have been demonstrated as an efficient pH sensor for living cells. The proposed sensor employs gold/silver core-shell nanoparticles (Au@Ag NPs) functionalized MWCNTs hybrid structure as the surface-enhanced Raman scattering (SERS) substrate and pATP molecules as the SERS reporters, which possess a pH-dependent SERS performance. By using MWCNTs as the substrate to be in a state of aggregation, the pH sensing range could be extended to pH 3.0～14.0, which is much wider than that using unaggregated Au@Ag NPs without MWCNTs. Furthermore, the pH-sensitive performance was well retained in living cells with a low cytotoxicity. The developed SERS-active MWCNTs-based nanocomposite is expected to be an efficient intracellular pH sensor for bio-applications.     

Spin-trapped Radicals: Determination by LC-TSP-MS and LC-ESI-MS

The 4-POBN[α-(4-pyridyl-l-oxide)-N-tert-butyl-nitrone] radical adducts of ethyl and pentyl radicals were determined by a combination of high performance liquid chromatography (HPLC) combined with electron paramagnetic resonance (EPR) with HPLC-electrospray (ESI)-mass spectrometry and HPLC-thermospray (TSP)-MS. The identifIcation of the peak corresponding to the spin-trapped radical was done by performing HPLC-EPR under the same chromatographic conditions as the HPLC-MS. The radical adducts could be determined by both techniques, even though for ESI only 12 μL/min of the total 1 mL/min HPLC flow rate could be directed into the ion source.     

Antitumoral and MMP-2 inhibition activity of raloxifene or tamoxifen loaded nanoparticles containing dimethyl-β-cyclodextrin

A new nanoparticle formulation has been developed by using dimethyl-β-cyclodextrin (DM-β-CD) with raloxifene HCl or tamoxifene citrate. Both drugs are insoluble in water and represent as low bioavailibilities when given orally. Tamoxifen has an FDA approval for breast cancer prevention and the treatment. Raloxifene is approved for osteoprosis treatment. Both drugs were selected as a model drug antitumoural activity and MMP-2 inhibition studies were evaluated on breast cancer cell lines MCF-7 and MDA-MB 231. MMP-2 is known to be responsible for tumour invasion and initation the of angiogenesis. DM-β-CD and sodium taurocholate (NaTC) have been used as absorption enhancers to increase penetration effect of raloxifene/tamoxifen on the tumour cells and aimed to provide high antitumoral activity and MMP-2 inhibition results by developed nanoparticle formulations. The effects of two absorption enhancers were compared. The highest antitumoral activity was observed for DM-β-CD—raloxifene HCl nanoparticle formulation and also MMP-2 enzyme inhibit effectively.     

Production of Pt nanoparticles-supported chelating group-modified graphene for direct methanol fuel cells

In this study, Pt nanoparticles (NPs) were supported on reduced graphene oxide with the aid of disodium ethylenediamine-tetraacetate, where the Pt iona were initially attached to EDTA-functionalized graphene oxide (EDTA-GO) sheets and then the metal ion and the graphene oxide were reduced simultaneously by ethylene glycol. Electrochemical properties of the catalysts were studied by measuring cyclic voltammetries, and functional groups of the synthesized materials were investigated by Fourier transform infrared spectrometry. Average sizes and lattice parameters were measured by scanning electron microscopy, transmission electron microscopy images, and X-ray diffraction. The results showed that Pt NPs were successfully deposited on the EDTA-GO with the crystallite size of about 2.3 nm. The prepared catalysts demonstrated an enhanced tolerance towards CO poisoning, when EDTA-GO was used as supports. This suggests that EDTA plays a crucial role in the dispersion and electrocatalytic activity of the metal nanoparticles.     

A label-free electrochemical biosensor for microRNA detection based on apoferritin-encapsulated Cu nanoparticles

MicroRNAs (miRNAs), a class of small endogenous nonprotein-coding RNAs, regulate a wide range of biological processes, and their abnormal expressions are related to the growth and development of plants. Thus, a simple, rapid, and highly sensitive assay for miRNA detection is of great significance. In this work, a label-free and ultrasensitive assay for miRNA detection using protein cage nanoparticles has been developed. Apoferritin-encapsulated Cu nanoparticles (Cu-apoferritin) could be immobilized on the electrode through special reaction between amino and carboxyl. Hybridization event between the probe DNA and the target miRNA-159a is confirmed by electrochemical oxidation signal after Cu released into the detection buffer by adjusting the pH. This assay is highly selective and sensitive with a low detection limit of 3.5 fM. Moreover, the developed method can even discriminate single-base mismatched strand between the complementary targets. The effect of abscisic acid on the expression level of miRNA-159a in Arabidopsis thaliana seeds was also investigated.     

Use of hydroxylapatite composite membranes for analysis of bisphenol A

This study evaluates solid-phase micro-extraction (SPME) coupled with gas chromatography–mass spectrometry (GC–MS) to determine trace levels of bis-phenol A in water and leached from plastic containers. In our study, we used very thin composite membranes prepared in the laboratory. The extraction using headspace post-derivatization with bis(trimethylsilyl) trifluoroacetamide (BSTFA), containing 1 % trimethylchlorosilane (TMCS) vapor, following SPME was compared with extraction without derivatization. The SPME experimental procedures to extract bis-phenol A in water were optimized with a relatively polar polyacrylate (PA)-coated fiber, an extraction time of 50 min, and desorption at 300 °C for 2 min. Headspace derivatization following SPME was performed using 7 μL of BSTFA with 1 % TMCS at 65 °C for 30 s. The precision was 5.2 % without derivatization and 9.0 % headspace derivatization. The detection limit was determined to be at the nanogram per liter level. When SPME was used following headspace derivatization, the detection limit was one order of magnitude better than that achieved without derivatization. The results of this study reveal the adequacy of the SPME–GC–MS method for analyzing bisphenol A leached from plastic containers. The concentrations of bisphenol A leached from plastic containers into water ranged from 0.7 to 78.5 μg L^?1.     

Weak acid–base interaction induced assembly for the formation of rambutan-like poly(styrene-alt-maleic anhydride)/silica composite microspheres

To investigate the effect of surface functionality on the morphology of polymer/silica composite, poly(styrene-alt-maleic anhydride) (SMA) spheres prepared via precipitation polymerization method was employed. In water/ethanol solution, diethanolamine (DEA) was used to catalyze the hydrolysis reaction of tetraethoxysilane (TEOS), and rambutan-like poly(styrene-alt-maleic anhydride)/silica (SMA/SiO₂) microspheres were synthesized through in situ sol–gel process. The obtained structure and morphology were characterized by FTIR, NMR, TEM, SEM, and TGA. The results showed that the hydrolyzed SMA chains on the surface was crucial to the nucleation and growth of silica, and the morphologies of SMA/SiO₂ composite microspheres can be controlled by the amount of DEA and the ratio of SMA/TEOS. In addition, the SMA/SiO₂ microspheres were used to prepare hierarchical structure of SMA/SiO₂/Ag particles, which were utilized for the construction of surface-enhanced Raman scattering substrate (SERS).     

Adsorption of polyprotic acid at the water/air interface

A rigorous thermodynamic treatment appropriate for surface adsorption from mixed aqueous solution of alkali and polyprotic acid was derived. Those equations were applied to mixed aqueous solution/air systems of alkali metal hydroxide and Fe^III complex with ethylenediamine- N, N, N′,N′-tetraacetate (Fe-EDTA). Surface density of each species arising from Fe-EDTA was separately evaluated, and thus, surface activity of Fe-EDTA was studied, especially its dependence on pH and how it is influenced by the counter cations. Fe-EDTA was positively adsorbed at the water/air interface at very low pHs and negatively at high pHs. The pH range of positive adsorption of Fe-EDTA with potassium ion, as a counter ion, was wider than that with sodium ion. Thus, potassium ion, a structure breaker, tended to smooth surface adsorption of Fe-EDTA at the water/air interface, whereas sodium ion, a structure maker, tended to withdraw Fe-EDTA from the interfacial region.     

Synthesis and preparation of nanoparticles composed of amphiphilic poly(γ-glutamic acid) with different hydrophobic side chains and their potential of membrane disruptive activity

In the development of nanoparticle-based vaccine adjuvants, the interaction between nanoparticles (NPs) and the cells is a key factor. To control them, we focused on the relationship between the hydrophobicity of the side chains and the cell membrane. In this study, amphiphilic poly(γ-glutamic acid) (γ-PGA), using various types of hydrophobic side chains, was synthesized and used to prepare NPs for evaluating the membrane disruptive activity. When leucine ethyl ester (Leu), methionine ethyl ester (Met), or tryptophan ethyl ester (Trp) was grafted, each polymer formed monodispersed NPs at physiological conditions. Significantly, NPs composed of Leu and Trp showed a membrane disruptive activity at the endosomal environment (pH 5–6.5), while NPs composed of Met did not show. This might be due to the weak hydrophobicity of Met compared to that of Leu and Trp, which demonstrated that the interaction between NPs and cells could be controlled by designing the polymer compositions.     

A New Stationary Phase for Hydrophilic Interaction Chromatography: Polyacrylate-Based Hydrophilic,Monosized-Porous Beads with Zwitterionic Molecular Brushes

Hydrophilic, polyacrylate-based, monosized-porous beads with zwitterionic molecular brushes were synthesized as a new stationary medium for hydrophilic interaction chromatography. Monosized-porous poly(glycerol-1,3-diglycerolate diacrylate-co-glycerol dimethacrylate), poly(GDGDA-co-GDMA), beads 5 μm in size were obtained by a staged-shape template polymerization. As an initiator for surface-initiated atom transfer radical polymerization (SI-ATRP), bromine functionality was obtained on the beads by reacting their hydroxyl groups with 3-(aminopropyl)triethoxysilane and α-bromoisobutyryl bromide, respectively. Zwitterionic molecular brushes on the hydrophilic poly(GDGDA-co-GDMA) beads were generated by SI-ATRP of a sulfobetaine monomer, [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl) ammonium hydroxide (MESH). Poly(MESH)-grafted poly(GDGDA-co-GDMA), poly(MESH)g-poly(GDGDAco-GDMA), beads were slurry packed into the microbore columns with 2 mm i.d. and evaluated as stationary medium for the separation of organic acids, nucleosides and peptides using microbore columns in hydrophilic interaction chromatography with the plate numbers up to 30,000 plates m^?1.     

Analysis of Genetic Diversity of Certain Species of Piper Using RAPD-Based Molecular Markers

The utility of RAPD markers in assessing genetic diversity and phenetic relationships of six different species of Piper from Northeast India was investigated. Polymerase chain reaction (PCR) with four arbitrary 10-mer oligonucleotide primers applied to the six species produced a total of 195 marker bands, of which, 159 were polymorphic. On average, six RAPD fragments were amplified per reaction. In the UPGMA phenetic dendrogram based on Jaccard’s coefficient, the different accessions of Piper showed a high level of genetic variation. This study may be useful in identifying diverse genetic stocks of Piper, which may then be conserved on a priority basis.     

Rapid and Sensitive LC–MS/MS Analysis of Fatty Acids in Clinical Samples

Free fatty acids (FFAs), major cellular metabolites, play an important role during tumor pathogenesis. Enhanced de novo fatty acid synthesis in tissues is a characteristic feature of cancer. Therefore, measurement of FFA concentration in biological samples is beneficial for cancer research and clinical diagnosis. Herein, a rapid, stable, and sensitive detection methodology was established to simultaneously quantify 22 FFAs using high-performance liquid chromatography/electrospray ionization tandem mass spectrometry (HPLC/ESI–MS/MS). The HPLC–MS/MS system was run in negative ion mode for 15 min using multiple reaction monitoring. The lipids were extracted from colon tissues of colon cancer patients and then injected into the HPLC–MS/MS system for analysis. Colon samples were analyzed by inter-day repeatability and intra-day repeatability, with less than 5 % deviation for most fatty acids. This approach is successful to determine low picogram concentrations of each FFA molecule using milligrams of tissue, and provides a promising method for FFA microanalysis in clinical samples.     

Relaxation properties and structures of polymer nanocomposites based on modified organoclays

Nanocomposite materials composed of HDPE and new guanidine-containing organoclays have been investigated. The basic changes in the relaxation properties of HDPE after the addition of guanidine-containing organoclays that vary in composition and content have been found. It has been shown that, depending on their structures and affinities for the polymer, guanidine-containing modifiers of montmorillonite have different effects on the structure and relaxation properties of the polymer.     

Electroactive shape memory effect of radiation cross-linked SBS/LLDPE composites filled with carbon black

The poly(styrene-b-butadiene-b-styrene) (SBS) triblock copolymer and linear low-density polyethylene (LLDPE) were blended and irradiated by γ rays to prepare shape memory polymer (SMP). Different weight fractions of conductive carbon black (CB) were filled into SMP to form a novel electroactive shape memory CB/SBS/LLDPE composite. The CB reinforced radiation cross-linked SBS/LLDPE blends for the improvement of the mechanical weakness and conductivity of SBS/LLDPE bulk and for wide practical engineering uses. The electroactive shape memory CB/SBS/LLDPE composites were investigated by electrical properties, mechanical, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and electroactive shape memory effects. It is found that the tensile strength, storage modulus, and resistance against mechanical and thermal mechanical cycle loading in the developed composites increased due to the role of reinforcement of CB. The melting temperatures and volume resistance of the composites decreased with the increment of CB for excellent electrical conductivity of CB. The electroactive shape memory effects of developed CB/SBS/LLDPE composites were affected by CB weight fractions and applied voltage, while good shape recovery could be obtained in the shape recovery test. When the CB fraction is more than 5 wt%, full recovery can be observed after tens of seconds and shape recovery speed increased with CB fractions and voltage increasing. However, the shape recovery rate decreases slightly with increment of cycle times.     

Need for database extension for reliable identification of bacteria from extreme environments using MALDI TOF mass spectrometry

The ability of MALDI TOF MS (matrix-assisted laser desorption ionisation time-of-flight mass spectrometry) to identify cultivable microflora from two waste disposal sites from non-ferrous metal industry was analysed. Despite the harsh conditions (extreme pH values and heavy metal content in red mud disposal site from aluminium production or high heavy metal content in nickel sludge), relatively high numbers of bacteria were recovered. In both environments, the bacterial community was dominated by Gram-positive bacteria, especially by actinobacteria. High-quality MALDI TOF mass spectra were obtained but most of the bacteria isolates could be not identified using MALDI Biotyper software. The overall identification rate was lower than 20 %; in two of the environments tested identification rates were lower than 10 %. As a dominant bacterial species, Microbacterium spp. in drainage water from an aluminium red mud disposal site near ?iar nad Hronom, Bacillus spp. in red mud samples from the same site, and Arthrobacter spp. from nickel smelter sludge near Sereï were identified by a combination of the Biolog system and 16S rRNA sequence analysis. As the primary focus of the MALDI TOF MS-based methodology is directed towards medically important bacteria, reference database spectra expansion and refinement are needed to improve the ability of MALDI TOF MS to identify environmental bacteria, especially those from extreme environments.