干涉法测量光学材料非线性折射率的方法研究

提出了一种基于楔形平板等厚干涉原理测量光学玻璃非线性折射率变化的方法。在理论分析的基础上,建立了变形的等厚干涉条纹变化△e／e与待测玻璃平片（K9玻璃）折射率变化量△nb之间的数学模型;在选取一定的实验条件下,获得等厚干涉实验测量干涉图样,并利用MATLAB对实验所得的干涉图进行图像数据处理分析计算,恢复出非线性变化光学玻璃材料的折射率变化量△nb该方法的测量精度可达10^-6。     

半导体激光Fabry-Perot干涉波长的微位移测量仪

摘要设计了一种基于Fabry-Perot干涉波长测量仪.这种测量仪使用两个Fabry-Perot干涉腔,其中一个作为测量腔、另一个作为参考腔,测量腔的一个反射面与被测对象安装在一起,参考腔的一个反射面与压电陶瓷安装在一起.根据透射光谱中心波长与其干涉腔长之间的关系,当参考腔与测量腔的透射光谱中心波长完全重合时,对纳米级微位移实现实时测量.光源采用半导体激光器,可获得所需要的波长值和波长变化范围.实验结果表明,这种测量仪测量误差不大于1.5 nm,该精度可以满足精密机械加工、光电子和微电子加工以及纳米级测量技术等领域的精度要求.     

Designing of interference pattern in ultra-short pulse laser processing

We have studied material processing by using an interfering ultra-short pulse laser. In this process, an interference pattern is transferred to material surface, and a periodic structure can be generated in a single shot of laser irradiation. Here, it is well known that the period of the interference pattern can be controlled by correlation angle and wavelength. In addition, a composite, doubled in density or designed interference pattern can be formed by controlling the phase shift and variation of amplitude between the interfering laser beams. In this paper, basic patterns of interference are summarized in the case of four-beam correlation.     

Young's double-slit experiment in photonic crystals

We present an experimental and numerical study of the transmission of a photonic crystal perforated by two subwavelength slits, separated by two wavelengths. The experimental near-field image of the double-slit design of the photonic crystal shows an interference pattern, which is analogous to Young's experiment. This interference arises as a consequence of the excitation of surface states of the photonic crystals and agrees very well with the simulations.     

Double-grating interferometer with a one-to-one correspondence with a Michelson interferometer

We describe a double-grating interferometer that has a one-to-one correspondence with a Michelson interferometer. The half spatial periods of the gratings are equivalent to the wavelengths of the interferometer. The widths of the interference fringes can be changed easily. The intensity distribution of the interference pattern is independent of the wavelength of the light source used. The surface profile of an object can be measured because two interference beams can coincide precisely on the image plane of the object. The measuring range is much larger than that of a Michelson interferometer.     

Plasmon-assisted two-slit transmission: Young's experiment revisited

We present an experimental and theoretical study of the optical transmission of a thin metal screen perforated by two subwavelength slits, separated by many optical wavelengths. The total intensity of the far-field double-slit pattern is shown to be reduced or enhanced as a function of the wavelength of the incident light beam. This modulation is attributed to an interference phenomenon at each of the slits, instead of at the detector. The interference arises as a consequence of the excitation of surface plasmons propagating from one slit to the other.     

基于法布里-珀罗干涉仪的大气风场及温度场探测理论研究及仿真

针对基于法布里-珀罗干涉仪的大气风场探测系统,推导了进行风速、温度反演的理论模型并在理论上进行了模拟验证.利用光学设计软件Zemax完成了法布里-珀罗干涉仪系统结构的仿真.通过设定不同波长入射系统,得到对应干涉条纹,利用最小二乘拟合圆方法从条纹峰值移动距离可反演出风速,与理论值进行比对,得到风速仿真误差小于4.2％.针...     

Processing of Diamond for Integrated Optic Devices Using Q-Switched Nd:YAG Laser at Different Wavelengths

In the present investigation, a Q-switched Nd:YAG laser is used to study the various aspects of diamond processing for fabricating integrated optic and UV optoelectronic devices. Diamond is a better choice of substrate compared to silicon and gallium arsenide for the fabrication of waveguides to perform operations such as modulation, switching, multiplexing, and filtering, particularly in the ultraviolet spectrum. The experimental setup of the present investigation consists of two Q-Switched Nd:YAG lasers capable of operating at wavelengths of 1064 nm and 532 nm. The diamond cutting is performed using these two wavelengths by making the “V”-shaped groove with various opening angle. The variation of material loss of diamond during cutting is noted for the two wavelengths. The cut surface morphology and elemental and structural analysis of graphite formed during processing in both cases are compared using scanning electron microscopy (SEM) and laser Raman spectroscopy. Both the Q-Switched Nd:YAG laser systems (at 1064 nm and 532 nm) show very good performance in terms of peak-to-peak output stability, minimal spot diameter, smaller divergence angle, higher peak power in Q-switched mode, and good fundamental TEM₀₀ mode quality for processing natural diamond stones. Less material loss and minimal micro cracks are achieved with wavelength 532 nm whereas a better diamond cut surface is achieved with processing at 1064 nm with minimum roughness.     

HgCdTe组分不均性对X射线反射率的影响

本征反射率是X射线衍射摇摆曲线计算机模拟的基础。用X射线动力学理论研究了组分不均匀对HgCdTe材料X射线反射率的影响。研究结果表明,横向组分不均匀性直接影响摇摆曲线的峰形,峰值反射率和半峰全宽随组分不均匀的增大而分别减小和增大,且与组分不均匀性的均方差近似成指数关系,但其积分反射率却基本保持不变;采用多层模型对具有线性组分梯度的HgCdTe半导体材料反射率的计算结果则表明,纵向组分梯度除导致反射率峰值强度下降外,还会引起摇摆曲线产生单边干涉效应,摇摆曲线的半峰全宽和干涉峰间距随组分梯度的增加而增大,而干涉峰间距与干涉周期之间的关系则随组分梯度的增加其偏离线性的程度增大。     

High-contrast interference pattern of amplified spontaneous emission from dyes under transient grating excitation

We demonstrate a high-contrast interference fringe pattern formed by amplified spontaneous emission (ASE) in a noncollinear two-beam self-diffraction setup by use of dyes. In the presence of a transient grating a stable interference pattern is observed in ASE induced by one- and two-photon absorption. The fringe visibility varies from 0.2 to 0.65 with a temporal delay in the two beams. The variation of the angle between the two exciting beams at the temporal overlap shows an increase in the fringe visibility with an increase in the angle.     

Mode coupling between first- and second-order whispering-gallery modes in coupled microdisks

The mode characteristics for two coupled microdisks are investigated by the finite-difference time-domain technique. In the two coupled micodisks, mode coupling between the same order whispering-gallery modes (WGMs) results in coupled WGMs with split mode wavelengths. The numerical results show that the split mode wavelengths of the coupled first- and second-order WGMs can have a crossing point in some cases, which can induce anticrossing mode coupling between them and greatly reduce the mode Q factor of the coupled first-order WGMs. The time variation of mode field pattern shows the transformation between the coupled first- and second-order WGMs.     

双波长LD模块的拉曼光谱测试系统

荧光干扰是拉曼光谱检测过程中常见的干扰因素之一,而移频激发法是一种有效的克服荧光干扰的检测手段。移频激发法利用两个波长相近的激光分别激发被测物质,并将获得的拉曼光谱进行差谱。由于两次激发的荧光背景相同,而拉曼特征峰会产生平移,因此可有效地消除荧光背景的干扰,进而利用一定的算法还原拉曼特征峰。移频激发法的关键在于两个激发光波长的稳定性,不稳定的波长差将严重影响对拉曼特征峰的还原效果。本文研制了一种拉曼光谱测试系统,该系统的双波长LD模块能够产生两个波长稳定的激发光(分别为784.7和785.8 nm),满足移频激发法的测试要求。影响激发光波长稳定性的因素主要是光功率和温度,本系统中对这两个因素均进行了实时的监控,以保证激发光波长的稳定。系统的硬件部分主要包括ARM主控板、双波长LD模块及其驱动电路、温度控制板、数字光开关、光谱检测光路和光纤探头(两个高功率的蝶形封装激光器);软件部分可自动获取被测物质的拉曼光谱图,并对其进行后续的处理。在稳定性测试实验中,对系统驱动电源电流和激光器温度的稳定性均进行了测试。测试结果显示,电流波动范围小于0.01 mA、温度变化范围小于0.004 ℃,能够有效地保证激发光波长的稳定性。最后,对某品牌花生油进行了拉曼光谱检测,并对检测结果进行了处理,获得了良好的效果。     

A Pressure Sensor Using Fiber Bragg Grating

In the present investigation, a Q-switched Nd:YAG laser is used to study the various aspects of diamond processing for fabricating integrated optic and UV optoelectronic devices. Diamond is a better choice of substrate compared to silicon and gallium arsenide for the fabrication of waveguides to perform operations such as modulation, switching, multiplexing, and filtering, particularly in the ultraviolet spectrum. The experimental setup of the present investigation consists of two Q-Switched Nd:YAG lasers capable of operating at wavelengths of 1064 nm and 532 nm. The diamond cutting is performed using these two wavelengths by making the “V”-shaped groove with various opening angle. The variation of material loss of diamond during cutting is noted for the two wavelengths. The cut surface morphology and elemental and structural analysis of graphite formed during processing in both cases are compared using scanning electron microscopy (SEM) and laser Raman spectroscopy. Both the Q-Switched Nd:YAG laser systems (at 1064 nm and 532 nm) show very good performance in terms of peak-to-peak output stability, minimal spot diameter, smaller divergence angle, higher peak power in Q-switched mode, and good fundamental TEM ₀₀ mode quality for processing natural diamond stones. Less material loss and minimal micro cracks are achieved with wavelength 532 nm whereas a better diamond cut surface is achieved with processing at 1064 nm with minimum roughness.     

Nonclassical interference and entanglement generation using a photonic crystal fiber pair photon source

We demonstrate two key components for optical quantum information processing: a bright source of heralded single photons; and a bright source of entangled photon pairs. A pair of pump photons produces a correlated pair of photons at widely spaced wavelengths (583 nm and 900 nm), via a chi((3)) four-wave mixing process. We demonstrate nonclassical interference between heralded photons from independent sources with a visibility of 95% (after correction for background), and an entangled photon pair source, with a fidelity of 89% with a Bell state.     

空间外差光谱仪干涉图非均匀性校正研究

空间外差光谱仪在研制加工过程中,由于加工误差及胶合误差会使CCD接收到的干涉图存在光强分布不均匀现象,降低了变换光谱的准确性。基于对空间外差光谱仪干涉图光强非均匀性的产生机制与特点分析基础上,提出了一种干涉图非均匀性校正方法,该方法通过对实际干涉图进行单调分解、分段归一化及重新组合过程求解出光强分布函数,然后将变换光谱与光强分布函数倒数的傅里叶变换结果进行卷积来获得非均匀性校正后的光谱,最后将校正光谱进行逆傅里叶变换从而实现干涉图的非均匀性校正。将此方法应用于空间外差试验仪的近红外实测单色光干涉图的非均匀性校正,结果显示,该方法可以有效改善干涉图光强分布的非均匀性,抑制变换光谱的边频信号,通过与仿真的理想光谱对比,1 571和1 572 nm光谱校正前后噪声的减小率分别达到40.7%和24%,提高了光谱信噪比和准确性。     

A simple method of contrast enhancement and extremum extraction for interference fringes

A method of interference fringe processing by finding the average and the extremum gray levels of image points within a fixed or varying window and then computing the modified image intensity with a simple algorithm is proposed. This method can yield a uniform brightness and high (1 or near to 1) contrast at the same time over the whole image area for an input pattern with low contrast and considerable luminance variation, when a relatively large window is used. It can also perform extremum extraction if a small window is employed. This technique is simple, effective and convenient for use, as has been verified by a series of examples of simulated and experimental fringe processing.     

Two-dimensional quasi-phase-matched multiple-cascaded four-wave mixing in periodically poled KTiOPO(4)

A two-dimensional quasi-phase-matched structure is realized in a noncollinear, nondegenerate periodically poled KTiOPO(4) parametric oscillator by utilizing the mutual coherence of two noncollinear pump beams. The mutually coherent pump beams form an interference pattern inside the crystal that is directed perpendicular to the existing quasi-phase-matched grating vector and acts as a parametric gain grating. The cavity itself supports two signal wavelengths around 1550 nm with tunable separation, while the gain grating reduces the operational threshold of the oscillator. Furthermore, with this two-dimensional quasi-phase-matched structure, we can demonstrate the generation of new spectral components through multiple chi((2)):chi((2))-cascaded four-wave mixing processes.     

偏振型干涉成像光谱仪谱线位置定标方法的研究

论述了偏振型干涉成像光谱仪的工作原理, 针对复原光谱谱线位置漂移问题, 提出了原理修正和数据处理两种具有代表性的实验室谱线位置定标方法, 给出了定标结果及对比分析. 原理修正方法从干涉型成像光谱仪的参数选择着手, 分析了产生谱线位置漂移的原因, 针对复原谱线位置随行变化的问题, 给出了修正方案, 使得谱线位置精度明显提高; 对于给定的四组激光器标准波长, 谱线位置均方根误差由定标前的28.3914下降至5.5371, 该方法对干涉型成像光谱仪具有普适性, 且其定标参数对分析仪器指标提供了便利. 数据处理方法弥补了原理修正定标存在的数据量大、短波定标效果弱等弊端, 谱线位置均方根误差下降至0.9178, 该方法实施简单, 对不同的输入波长, 所取不同行的数据用统一的表达式进行修正. 该方法化繁为简、间接定标的思想具有一定的借鉴价值. 该研究为偏振型干涉成像光谱仪的设计、研制、调试和工程化提供了重要的理论依据和实践指导.     

基于连续光谱分析的在线水质检测信号处理研究

在线光谱水质检测仪器是现代水资源环境监测技术的重要发展方向之一,具有多参数监测和准确度高、重复性好的技术优势,然在线被测水样的光谱信号处理是其关键核心技术,为此,基于连续光谱分析,建立了在线被测水样光谱测量信号的数学模型,提出了基于双波长光强比值不变性的光谱测量信号系统误差处理方法,并结合小波多分辨率滤波噪声处理技术,系统研究了基于在线被测水质参数光谱特征的背景干扰处理方法。以上信号处理方法应用于自主研制的多参数光谱水质监测仪器,在线检测标准环境水样及实际环境水样中的化学需氧量、六价铬和阴离子表面活性剂等水质参数,并与国家标准分析方法展开了现场对比测试,仪器的关键参数重复性(相对标准偏差RSD≤10%)与准确度(实际水样比对试验相对误差A≤10%)均达到并优于国家环境保护技术标准要求,表明该信号处理方法能够有效消除在线水质检测光谱测量信号的系统误差及噪声与背景干扰,对于提升光谱水质监测仪器的技术性能具有重要的作用。