The Influence of Charge Transport and Recombination on the Performance of Dye‐Sensitized Solar Cells

Electrochemical impedance spectroscopy (EIS) and transient voltage decay measurements are applied to compare the performance of dye sensitized solar cells (DSCs) using organic electrolytes, ionic liquids and organic‐hole conductors as hole transport materials (HTM). Nano‐crystalline titania films sensitized by the same heteroleptic ruthenium complex NaRu(4‐carboxylic acid‐4′‐carboxylate) (4,4′‐dinonyl‐2,2′‐bipyridyl)(NCS)₂ , coded Z‐907Na are employed as working electrodes. The influence of the nature of the HTM on the photovoltaic figures of merit, that is, the open circuit voltage, short circuit photocurrent and fill factor is evaluated. In order to derive the electron lifetime, as well as the electron diffusion coefficient and charge collection efficiency, EIS measurements are performed in the dark and under illumination corresponding to realistic photovoltaic operating conditions of these mesoscopic solar cells. A theoretical model is established to interpret the frequency response off the impedance under open circuit conditions, which is conceptually similar to photovoltage transient decay measurements. Important information on factors that govern the dynamics of electron transport within the nanocrystalline TiO₂ film and charge recombination across the dye sensitized heterojunction is obtained.     

Multifunctional Ag‐Decorated Porous TiO2 Nanofibers in Dye‐Sensitized Solar Cells: Efficient Light Harvesting,Light Scattering,and Electrolyte Contact

Designing the photoanode structure in dye‐sensitized solar cells (DSSCs) is vital to realizing enhanced power conversion efficiency (PCE). Herein, novel multifunctional silver‐decorated porous titanium dioxide nanofibers (Ag/pTiO₂ NFs) made by simple electrospinning, etching, and chemical reduction processes are introduced. The Ag/pTiO₂ NFs with a high surface area of 163 m² g^?1 provided sufficient dye adsorption for light harvesting. Moreover, the approximately 200 nm diameter and rough surface of the Ag/pTiO₂ NFs offered enough light scattering, and the enlarged interpores among the NFs in the photoanode also permitted electrolyte circulation. Ag nanoparticles (NPs) were well dispersed on the surface of the TiO₂ NFs, which prevented aggregation of the Ag NPs after calcination. Furthermore, a localized surface plasmon resonance effect by the Ag NPs served to increase the light absorption at visible wavelengths. The surface area and amount of Ag NPs was optimized. The PCE of pTiO₂ NF‐based DSSCs was 27 % higher (from 6.2 to 7.9 %) than for pure TiO₂ NFs, whereas the PCE of Ag/pTiO₂ NF‐based DSSCs increased by about 12 % (from 7.9 to 8.8 %). Thus, the PCE of the multifunctional pTiO₂ NFs was improved by 42 %, that is, from 6.2 to 8.8 %.     

Brookite TiO2 Nanoparticle Films for Dye‐Sensitized Solar Cells

Brookite TiO₂ nanoparticles have been synthesized at low temperature by a soft solution growth method and have been used as building blocks to prepare pure brookite nanoparticle porous films. The film brookite structure was confirmed by XRD and Raman spectroscopy. By spectrophotometry, it was shown that the films had a direct band gap of 3.4 eV. After sensitization by the N719 dye, efficient cells have been produced. A best overall conversion efficiency of 5.97 %, without a scattering layer, was found for the larger TiO₂ starting nanoparticles. The cell open‐circuit voltage was improved compared with that of anatase cells and a lower electron diffusion coefficient was found in the photoanodes made of smaller brookite particles. Lanthanum‐doped brookite nanoparticle films were also studied. They showed a marked decreased in the amount of dye loading, and hence, the solar cells had a reduced current density that was not compensated for by the increased open‐circuit voltage of the cells.     

Recent Developments in Dye‐Sensitized Solar Cells

The knowledge of dye‐sensitized solar cells (DSCs) has expanded considerably in recent years. They are multiparameter and complex systems that work only if various parameters are tuned simultaneously. This makes it difficult to target to a single parameter to improve the efficiency. There is a wealth of knowledge concerning different DSC structures and characteristics. In this review, the present knowledge and recent achievements are surveyed with emphasis on the more promising cell materials and designs.     

染料敏化太阳电池中的电子传输及复合

电子传输与复合是染料敏化太阳电池中仍然存在争议的基本物理过程,解决这些争议对于进一步提高染料敏化太阳电池的光伏性能及稳定性是至关重要的。多缺陷理论模型用扩散系数及电子寿命这两个基本物理量准确地描述了染料敏化太阳电池中的电子传输及复合。为了对扩散系数及电子寿命等物理参数进行实验测量,近年来,人们发展出了频域、时域以及稳态等多种实验方法和技术手段,本文对这些方法进行了综述,并分别从纳晶半导体光阳极、电解质以及敏化染料等方面评述了近年来电子传输及复合的相关研究进展。     

Tuning the Electrical and Optical Properties of Diketopyrrolopyrrole Complexes for Panchromatic Dye‐Sensitized Solar Cells

A series of metal‐free organic dyes that were bridged by a diketopyrrolopyrrole moiety and were composed of indoline and triphenylamine as donor groups and furan and benzene as conjugated spacer groups were designed and synthesized for use in dye‐sensitized solar cells (DSCs). The photophysical properties, electrochemical properties, and performance of the DSCs were related to the structure of their corresponding dyes. Their absorption spectra broadened upon the introduction of the indoline and heterocyclic furan moieties through fine‐tuning of their molecular configuration. The overall conversion efficiencies of DSCs that were based on these dyes ranged from 5.14–6.53 %. Among the four dyes that were tested, indoline‐based ID01 and ID02 showed higher efficiencies (6.35 % and 6.53 %) as a result of their improved light‐harvesting efficiency and larger electron driving force. The ID01 dye, which contained an indoline moiety as an electron donor and a furan group as a π‐conjugated linker, showed an excellent monochromatic incident‐photon‐to‐current‐conversion efficiency (IPCE) spectrum (350–650 nm) with a maximum value of 78 % in the high plateau region and an onset value close to 800 nm. Intensity‐modulated photovoltage spectroscopy (IMVS) and impedance spectroscopy (IS) revealed that dyes that contained benzene conjugation spacers suppressed the charge‐recombination rate more efficiently than dyes that contained furan spacers, thereby resulting in improved photovoltage.     

Low‐cost Nickel Complex Dye‐sensitized Titania Nanoparticle/nanotube Composites for Solar Cells

In this work, high‐performance dye‐sensitized solar cells (DSSCs) based on new low‐cost visible nickel complex dye (VisDye), TiO₂ nanoparticle/nanotube composites electrodes, carbon nanoparticles counter electrodes, and ionic liquids electrolytes have been fabricated. The electronic structure, optical spectroscopy, and electrochemical properties of the VisDye were studied. Experimental results indicate that it is beneficial to improve the electron transport and power conversion efficiency using the nickel complex VisDye and TiO₂ nanoparticle/nanotube composites. Under optimized conditions, the solar energy conversion efficiencies were measured. The short‐circuit current density (J_SC), the open‐circuit voltage (V_OC), the fill factor (FF), and the overall efficiency (η) of the DSSCs are 10.01 mA/cm², 516 mV, 0.68, and 3.52%, respectively. This study demonstrates that the combination of new VisDye with TiO₂ nanoparticle/nanotube composites electrodes and carbon nanoparticles counter electrodes provide a way to fabricate highly efficient dye‐sensitized solar cells in low‐cost production.     

A Novel Improved Method to Increase the Efficiency of Dye‐Sensitized Solar Cells

A novel improved method which employs a reflective mirror at the back of the Pt counter electrode is used in dye‐sensitized solar cells (DSSC). The direction of the light propagation in the cells was changed because of adding a mirror and the light reflected back into the DSSC in order to enhance the optical absorption of the DSSCs. Therefore, the performance of the cells was improved distinctively. The TiO₂ electrodes were characterized by X‐ray diffraction, scanning electron microscopy and I‐V properties of the cells measured by Linear Sweep Voltammetry system. The results indicates that the conversion efficiency can be increased from 4.81% to 5.43% under AM 1.5 illumination when a mirror is added at the back of the Pt counter electrode in the same cell. Meanwhile, the Jsc, Voc and the fill factor can be obtained 18.65 mA/cm², 0.728 V and 0.561, respectively.     

SiO2/TiO2 Hollow Nanoparticles Decorated with Ag Nanoparticles: Enhanced Visible Light Absorption and Improved Light Scattering in Dye‐Sensitized Solar Cells

Hollow SiO₂/TiO₂ nanoparticles decorated with Ag nanoparticles (NPs) of controlled size (Ag@HNPs) were fabricated in order to enhance visible‐light absorption and improve light scattering in dye‐sensitized solar cells (DSSCs). They exhibited localized surface plasmon resonance (LSPR) and the LSPR effects were significantly influenced by the size of the Ag NPs. The absorption peak of the LSPR band dramatically increased with increasing Ag NP size. The LSPR of the large Ag NPs mainly increased the light absorption at short wavelengths, whereas the scattering from the SiO₂/TiO₂ HNPs improved the light absorption at long wavelengths. This enabled the working electrode to use the full solar spectrum. Furthermore, the SiO₂ layer thickness was adjusted to maximize the LSPR from the Ag NPs and avoid corrosion of the Ag NPs by the electrolyte. Importantly, the power conversion efficiency (PCE) increased from 7.1 % with purely TiO₂‐based DSSCs to 8.1 % with HNP‐based DSSCs, which is an approximately 12 % enhancement and can be attributed to greater light scattering. Furthermore, the PCEs of Ag@HNP‐based DSSCs were 11 % higher (8.1 vs. 9.0 %) than the bare‐HNP‐based DSSCs, which can be attributed to LSPR. Together, the PCE of Ag@HNP‐based DSSCs improved by a total of 27 %, from 7.1 to 9.0 %, due to these two effects. This comparative research will offer guidance in the design of multifunctional nanomaterials and the optimization of solar‐cell performance.     

A New Layered Photocathode with Porous NiO Nanosheets: An Effective Candidate for p‐Type Dye‐Sensitized Solar Cells

Herein, with the purpose of improving the efficiency of p‐type dye‐sensitized solar cells (DSSCs), a new layered photocathode (LP) is fabricated from irregular overlapping wrinkled porous NiO nanosheets. The LP was sensitized by using a commonly used dye, coumarin 343(C343), and then assembled into p‐type DSSCs through coupling with a platinum photoanode. Photoelectochemical characterization showed that the LP cell exhibited a clearly enhanced power‐conversion efficiency (by a factor of 4) compared with a cell with a NiO‐nanoparticle photocathode (NP). This excellent performance could be attributed to the overlapping layered structure, which favored hole transport, as confirmed by electrochemical impedance spectroscopy, and to the large surface area of the porous NiO nanosheets, which were favorable for dye adsorption.     

Molecular Design Rule of Phthalocyanine Dyes for Highly Efficient Near‐IR Performance in Dye‐Sensitized Solar Cells

A series of zinc–phthalocyanine sensitizers ( PcS16 – 18 ) with different adsorption sites have been designed and synthesized in order to investigate the dependence of adsorption‐site structures on the solar‐cell performances in zinc–phthalocyanine based dye‐sensitized solar cells. The change of adsorption site affected the electron injection efficiency from the photoexcited dye into the nanocrystalline TiO₂ semiconductor, as monitored by picosecond time‐resolved fluorescence spectroscopy. The zinc–phthalocyanine sensitizer PcS18 , possessing one carboxylic acid directly attached to the ZnPc ring and six 2,6‐diisopropylphenoxy units, showed a record power conversion efficiency value of 5.9 % when used as a light‐harvesting dye on a TiO₂ electrode under one simulated solar condition.     

Benzoporphyrins: Selective Co‐sensitization in Dye‐Sensitized Solar Cells

A novel class of dyes, namely benzoporphyrins, was synthesized and implemented into dye‐sensitized solar cells. They feature complementary absorptions compared to N719 , which renders them promising candidates for co‐sensitization in DSSCs. Notably, metallated benzoporphyrins reveal a TiO₂–nanoparticle attachment that is size and aggregation dependent. Therefore, unproductive energy‐transfer events between the selectively attached dyes can be prevented. In light of the latter, an efficiency improvement of 39 % has been achieved upon selective adsorption of benzoporphyrins and N719 onto different layers of TiO₂ photoelectrode.     

Comparison of Trap‐state Distribution and Carrier Transport in Nanotubular and Nanoparticulate TiO2 Electrodes for Dye‐Sensitized Solar Cells

Dye‐sensitized solar cells (DSCs) with nanotubular TiO₂ electrodes of varying thicknesses are compared to DSCs based on conventional nanoparticulate electrodes. Despite the higher degree of order in one‐dimensional nanotubular electrodes, electron transport times and diffusion coefficients, determined under short‐circuit conditions, are comparable to those of nanoparticulate electrodes. The quasi‐Fermi level, however, is much lower in the nanotubes, suggesting a lower concentration of conduction band electrons. This provides evidence for a much higher diffusion coefficient for conduction band electrons in nanotubes than in nanoparticulate films. The electron lifetime and the diffusion length are significantly longer in nanotubular TiO₂ electrodes than in nanoparticulate films. Nanotubular electrodes have a trap distribution that differs significantly from nanoparticulate electrodes; they possess relatively deeper traps and have a characteristic energy of the exponential distribution that is more than two times that of nanoparticulate electrodes.     

Enhancing the Performance of Dye‐Sensitized Solar Cells with a Gold‐Nanoflowers Box

To improve the electron collection, electron lifetime, and light‐harvesting efficiency of dye‐sensitized solar cells simultaneously, Au nanoflowers were prepared and used to cover the entire TiO₂ film. Deposition of Au nanoflowers around the TiO₂ film formed a light‐scattering “box” that covered the entire TiO₂ film. Compared with a light‐scattering layer that only covers the top surface of TiO₂, the Au‐nanoflowers box exhibited better light‐harvesting efficiency due to omnidirectional light scattering, faster electron transport (attributed to the formation of electron channels between the metallic Au nanoflowers and the electron‐collection electrode), and slower charge recombination. As a consequence, the short‐circuit photocurrent and open‐circuit photovoltage were both enhanced significantly, which improved the power conversion efficiency from 8.12 to 10.91 % (34 %) when an Au‐nanoflowers box was wrapped around the photoanode.     

Novel Thiazolo[5,4‐d]thiazole‐Based Organic Dyes for Quasi‐Solid‐State Dye‐Sensitized Solar Cells

A series of novel metal‐free organic dyes containing the thiazolo[5,4‐d]thiazole moiety were designed and synthesized for quasi‐solid‐state dye‐sensitized solar cells (DSSCs). Different alkoxy chains were introduced into the electron donor part of the dye molecules for comparison. The optical, electrochemical, and photovoltaic properties for all sensitizers were systematically investigated. It was found that the sensitizers with the different alkoxy groups have similar photophysical and electrochemical properties, such as absorbance and energy levels, owing to their close chemical structures. However, the quasi‐solid‐state DSSCs based on the resulting sensitizers exhibit different performance parameters. The quasi‐solid‐state DSSC based on sensitizer FNE74 with two octyloxy chains possessed the highest solar energy conversion efficiency of 5.10 % under standard AM 1.5G sunlight illumination without the use of coadsorbant agents.     

Ultrafast Photodynamics of the Indoline Dye D149 Adsorbed to Porous ZnO in Dye‐Sensitized Solar Cells

We investigate the ultrafast dynamics of the photoinduced electron transfer between surface‐adsorbed indoline D149 dye and porous ZnO as used in the working electrodes of dye‐sensitized solar cells. Transient absorption spectroscopy was conducted on the dye in solution, on solid state samples and for the latter in contact to a I^?/I₃^? redox electrolyte typical for dye‐sensitized solar cells to elucidate the effect of each component in the observed dynamics. D149 in a solution of 1:1 acetonitrile and tert‐butyl alcohol shows excited‐state lifetimes of 300±50 ps. This signature is severely quenched when D149 is adsorbed to ZnO, with the fastest component of the decay trace measured at 150±20 fs due to the charge‐transfer mechanism. Absorption bands of the oxidized dye molecule were investigated to determine regeneration times which are in excess of 1 ns. The addition of the redox electrolyte to the system results in faster regeneration times, of the order of 1 ns.     

Adsorption of 4‐tert‐Butylpyridine on TiO2 Surface in Dye‐Sensitized Solar Cells

4‐tert‐Butylpyridine (4‐TBP) has been widely used as additive in dye‐sensitized solar cells (DSC), owing to its improvement of the fill factor and the open circuit voltage of DSC. In this paper, the adsorption of 4‐TBP on the rutile TiO₂(110) surface in DSC was studied by using the density functional theory at DFT/B3LYP level. By comparing the results with those attained from experiments, it was concluded that the 4‐TBP could chemiadsorb on the incompletely covered surface Ti atoms in the electrode. The probable mechanism of compressed recombination by coordinated 4‐TBP in DSC was proposed.     

Photophysical and Electrochemical Properties,and Molecular Structures of Organic Dyes for Dye‐Sensitized Solar Cells

Dye‐sensitized solar cells (DSSCs) based on organic dyes adsorbed on oxide semiconductor electrodes, such as TiO₂, ZnO, or NiO, which have emerged as a new generation of sustainable photovoltaic devices, have attracted much attention from chemists, physicists, and engineers because of enormous scientific interest in not only their construction and operational principles, but also in their high incident‐solar‐light‐to‐electricity conversion efficiency and low cost of production. To develop high‐performance DSSCs, it is important to create efficient organic dye sensitizers, which should be optimized for the photophysical and electrochemical properties of the dyes themselves, with molecular structures that provide good light‐harvesting features, good electron communication between the dye and semiconductor electrode and between the dye and electrolyte, and to control the molecular orientation and arrangement of the dyes on a semiconductor surface. The aim of this Review is not to make a list of a number of organic dye sensitizers developed so far, but to provide a new direction in the epoch‐making molecular design of organic dyes for high photovoltaic performance and long‐term stability of DSSCs, based on the accumulated knowledge of their photophysical and electrochemical properties, and molecular structures of the organic dye sensitizers developed so far.     

Enhanced Charge Separation Efficiency in Pyridine‐Anchored Phthalocyanine‐Sensitized Solar Cells by Linker Elongation

A series of zinc phthalocyanine sensitizers ( PcS22 – 24 ) having a pyridine anchoring group are designed and synthesized to investigate the structural dependence on performance in dye‐sensitized solar cells. The pyridine‐anchor zinc phthalocyanine sensitizer PcS23 shows 79 % incident‐photon to current‐conversion efficiency (IPCE) and 6.1 % energy conversion efficiency, which are comparable with similar phthalocyanine dyes having a carboxylic acid anchoring group. Based on DFT calculations, the high IPCE is attributed with the mixture of an excited‐state molecular orbital of the sensitizer and the orbitals of TiO₂. Between pyridine and carboxylic acid anchor dyes, opposite trends are observed in the linker‐length dependence of the IPCE. The red‐absorbing PcS23 is applied for co‐sensitization with a carboxyl‐anchor organic dye D131 that has a complementary spectral response. The site‐selective adsorption of PcS23 and D131 on the TiO₂ surface results in a panchromatic photocurrent response for the whole visible‐light region of sun light.