Inorganic polymer photoresist for direct ceramic patterning by photolithography

A novel negative, inorganic polymer photoresist was demonstrated to be suitable for simple and direct fabrication of tribological SiCN-based ceramic microstructures via UV photolithography and subsequent pyrolysis at 800 degrees C.     

Photosensitive acrylate copolymer for electrodeposition photoresist

A photosensitive random copolymer UPDHES was prepared by introducing the acrylate groups into the side chain of the copolymer composed of N,N-dimethylaminomethyl methacrylate (DMAEMA), 2-hydroxyethyl acrylate (HEA), 2-ethylhexyl acrylate (EHA), and styrene (St) (PDHES). The molecular structure of UPDHES was characterized by FTIR and ¹H NMR analyses. Self-assembling of the random copolymer UPDHES in water formed positively charged photosensitive particles, and the particles were measured by TEM to be spherical-like nano-particles range from 20–90 nm. The oriented deposition of the particles on gold electrode was investigated with the cyclic voltammetry and TEM under low applied voltage. The influence of high applied voltage on current density in electrodeposition process and thickness of films were investigated also. Besides, the photopolymerization rate and final C=C conversion reached to the highest values with 3 wt % Irgacure 1173 addition, whereas decreased as further added. Moreover, an exposure-development procedure of electrodeposition UPDHES film produced developed diagram with resolution of 15 μm.     

Ordered mesoporous ceramics stable up to 1500 degrees C from diblock copolymer mesophases

In the present study, a poly(isoprene-block-dimethylamino ethyl methacrylate) diblock copolymer (PI-b-PDMAEMA) is used to structure-direct a polysilazane pre-ceramic polymer, commercially known as Ceraset. To the polymer was added a 2-fold excess in weight of the silazane oligomer (Ceraset). The resulting composite was cast into films, and after cooperative self-assembly of block copolymer and Ceraset, the structure was permanently set in the hexagonal columnar morphology, as evidenced by small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). Cross-linking of the silazane oligomer was achieved with a radical initiator at 120 degrees C. Upon heating of the composite to 1500 degrees C under nitrogen, the structure is preserved and a mesoporous ceramic material is obtained, as demonstrated by SAXS and TEM. The pores are open and accessible, as evidenced by nitrogen sorption/desorption measurements indicating a surface area of about 51 m2 g-1 and a pore diameter of 13 nm, consistent with TEM analysis. These results suggest that the use of block copolymer mesophases may provide a simple, easily controlled pathway for the preparation of various high-temperature ceramic mesostructures.     

Surfactant-free synthesis of amphiphilic diblock copolymer nanoparticles via nitroxide-mediated emulsion polymerization

Amphiphilic hairy nanoparticles are prepared in a one step, batch, heterogeneous polymerization of styrene or n-butyl acrylate, using a water-soluble poly(sodium acrylate) alkoxyamine macroinitiator based on the SG1 nitroxide.     

Monte Carlo phase diagram for diblock copolymer melts

A partial phase diagram is constructed for diblock copolymer melts using lattice-based Monte Carlo simulations. This is done by locating the order-disorder transition (ODT) with the aid of a recently proposed order parameter and identifying the ordered phase over a wide range of copolymer compositions (0.2相似文献   

Surface-functionalized CdSe nanorods for assembly in diblock copolymer templates

Poly(ethylene oxide)-covered CdSe nanorods were prepared and assembled in diblock copolymer templates by floating the block copolymer templates onto aqueous nanorod solutions. The assembly was enabled by consideration of the surface ligand coverage of the nanorods. Alkane-covered CdSe nanorods prepared by state-of-the-art techniques are not compatible with this assembly process. However, poly(ethylene oxide) (PEO)-functionalized CdSe nanorods were successfully used to assemble the nanorods into the channels and pores of diblock copolymer templates. Other water-dispersible CdSe nanorods, such as those covered with 11-mercaptoundecanoic acid (MUA), did not give the desired assemblies. These results are understood by considering the surface energies of the PEO-covered CdSe nanorods in this interfacial assembly process.     

Synthesis and surface properties of a new fluorinated acrylic diblock copolymer via AGET ATRP

A series of fluorinated diblock copolymers poly(2,2,3,4,4,4-hexafluorobutyl methacrylate)-b-poly(glycidyl methacrylate) PHFMA-b-PGMA with different fluorine content were synthesized by activator generated by electron transfer atom transfer radical polymerization (AGET ATRP). FTIR, ¹H NMR and GPC data verified feasibility and controllability of the synthesis. In order to evaluate the effect of chain structure on the surface properties, corresponding homopolymer poly(2,2,3,4,4,4-hexafluorobutyl methacrylate) and random copolymer copoly(2,2,3,4,4,4-hexafluorobutyl methacrylate-r-glycidyl methacrylate) were also comparatively studied. Contact angle measurements indicated that the water and ethyleneglycol contact angles of block- and random copolymers increased with increase of fluorine content, but in different manner. This difference comes from different surface energy at the same fluorine content on film surface. The surface stability of block-copolymer was obviously better than that of random copolymer; the same results were observed in heat resistance tests.     

Shape-shifting thermoreversible diblock copolymer nano-objects via RAFT aqueous dispersion polymerization of 4-hydroxybutyl acrylate

2-Hydroxypropyl methacrylate (HPMA) is a useful model monomer for understanding aqueous dispersion polymerization. 4-Hydroxybutyl acrylate (HBA) is an isomer of HPMA: it has appreciably higher aqueous solubility so its homopolymer is more weakly hydrophobic. Moreover, PHBA possesses a significantly lower glass transition temperature than PHPMA, which ensures greater chain mobility. The reversible addition–fragmentation chain transfer (RAFT) aqueous dispersion polymerization of HBA using a poly(ethylene glycol) (PEG₁₁₃) precursor at 30 °C produces PEG₁₁₃–PHBA_200–700 diblock copolymer nano-objects. Using glutaraldehyde to crosslink the PHBA chains allows TEM studies, which reveal the formation of spheres, worms or vesicles under appropriate conditions. Interestingly, the partially hydrated highly mobile PHBA block enabled linear PEG₁₁₃–PHBA_x spheres, worms or vesicles to be reconstituted from freeze-dried powders on addition of water at 20 °C. Moreover, variable temperature ¹H NMR studies indicated that the apparent degree of hydration of the PHBA block increases from 5% to 80% on heating from 0 °C to 60 °C indicating uniform plasticization. In contrast, the PHPMA_x chains within PEG₁₁₃–PHPMA_x nano-objects become dehydrated on raising the temperature: this qualitative difference is highly counter-intuitive given that PHBA and PHPMA are isomers. The greater (partial) hydration of the PHBA block at higher temperature drives the morphological evolution of PEG₁₁₃–PHBA₂₆₀ spheres to form worms or vesicles, as judged by oscillatory rheology, dynamic light scattering, small-angle X-ray scattering and TEM studies. Finally, a variable temperature phase diagram is constructed for 15% w/w aqueous dispersions of eight PEG₁₁₃–PHBA_200–700 diblock copolymers. Notably, PEG₁₁₃–PHBA₃₅₀ can switch reversibly from spheres to worms to vesicles to lamellae during a thermal cycle.

RAFT aqueous dispersion polymerization of 4-hydroxybutyl acrylate (HBA) affords shape-shifting thermoresponsive diblock copolymer nano-objects. ¹H NMR studies suggest that such behavior involves uniform plasticization of the PHBA block.     

Ordered mesoporous silicas and carbons with large accessible pores templated from amphiphilic diblock copolymer poly(ethylene oxide)-b-polystyrene

Highly ordered mesoporous carbons and silicas with ultralarge accessible pores have been successfully synthesized by using laboratory-made poly(ethylene oxide)-b-polystyrene (PEO-b-PS) diblock copolymers as templates via the evaporation-induced self-assembly (EISA) approach. Resols and tetraethyl orthosilicate (TEOS) serve as carbon and silica precursors, respectively. Small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM) measurements show that the mesoporous carbons (denoted as C-FDU-18) possess face centered cubic closed-packing (fcc) mesostructure (Fm3m) with large-domain ordering. N2 sorption isotherms reveal a large mesopore at the mean value of 22.6 nm with a narrow pore-size distribution. Mesoporous silicas (Si-FDU-18) also display a highly ordered fcc closed-packing mesostructure with an ultralarge unit cell (a = 54.6 nm). A hydrothermal recrystallization was introduced for the first time to produce micropores in thick silica walls (approximately 7.7 nm) and thus to generate ultralarge accessible mesopores (30.8 nm). Notably, the amphiphilic diblock copolymer with high molecular weight (PEO125-PS230, 29700 g mol-1) in this report was prepared via a simple method of atom transfer radical polymerization (ATRP). It can be easily available for chemists even without any experience in polymer synthesis.     

Plasmid DNA encapsulation within cationic diblock copolymer vesicles for gene delivery

We report the design and structural characterization of cationic diblock copolymer vesicles loaded with plasmid DNA based on a single emulsion technique. For this purpose, a DNA solution was emulsified in an organic solvent and stabilized by an amphiphilic diblock copolymer. The neutral block forms an interfacial brush, whereas the cationic attachment complexes with DNA. A subsequent change of the quality of the organic solvent results in the collapse of the brush and the formation of a capsule. The capsules are subsequently dispersed in aqueous medium to form vesicles and stabilized with an osmotic agent in the external phase. Inside the vesicles, the plasmid is compacted in a liquid-crystalline fashion as shown by the appearance of birefringent textures under crossed polarizers and the increase in fluorescence intensity of labeled DNA. The compaction efficiency and the size distribution of the vesicles were determined by light and electron microscopy, and the integrity of the DNA after encapsulation and subsequent release was confirmed by gel electrophoresis. We demonstrate reverse transfection of in vitro cultured HeLa cancer cells growing on plasmid-copolymer vesicles deposited on a glass substrate.     

Surface chemical functionalization of cylindrical nanopores derived from a polystyrene-poly(methylmethacrylate) diblock copolymer via amidation

This paper demonstrated covalent functionalization of surface -COOH groups on cylindrical nanopores derived from a polystyrene-poly(methylmethacrylate) diblock copolymer (PS- b-PMMA) via amidation mediated by 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide (EDC). The surface functionalization led to conversion of the surface charge of the nanopores and also to the shrinkage of effective pore radius, as verified using cyclic voltammetry for PS- b-PMMA-derived nanoporous films immobilized on gold substrates. For native PS- b-PMMA-derived nanoporous films, the redox current of anionic Fe(CN) 6 (3-) decreased with increasing solution pH due to the deprotonation of the surface -COOH groups, whereas those of cationic Ru(NH 3) 6 3+ and uncharged 1,1'-ferrocenedimethanol (Fc(CH 2OH) 2) were similar regardless of pH. In contrast, upon EDC-mediated amidation of the nanopore surface with ethylenediamine, the redox current of Ru(NH 3) 6 3+ decreased with decreasing pH and those of Fe(CN) 6 (3-) and Fc(CH 2OH) 2 were independent of pH. The decrease in redox current of Ru(NH 3) 6 3+ at acidic pH was consistent with the presence of -NH 2 groups on the nanopore surface as a result of the covalent immobilization of ethylenediamine. Furthermore, the redox current of Fc(CH 2OH) 2 decreased upon amidation of the nanopores with tetraethyleneglycol monoamine ((PEO) 4NH 2), reflecting the shrinkage of the effective pore radius. The control of the surface charge and effective radius of the nanopores via EDC-mediated amidation will provide a simple means for controlling the selectivity of molecular mass transport through PS- b-PMMA-derived nanopores.     

An electrochemical biosensor for direct detection of DNA using polystyrene-g-soya oil-g-imidazole graft copolymer

A label-free electrochemical DNA biosensor was developed through the attachment of polystyrene-g-soya oil-g-imidazole graft copolymer (PS-PSyIm) onto modified graphene oxide (GO) electrodeposited on glassy carbon electrode (GC). GC/GO electrode was initially functionalised via electrochemical reduction of 4-nitrobenzene diazonium salt, followed by the electrochemical reduction of NO₂ to NH₂. Subsequent to the electrochemical deposition of gold nanoparticles on modified surface, the attachment of the PS-PSyIm graft copolymer on the resulting electrode was achieved. The interaction of PS-PSyIm with DNA at the bare glassy carbon electrode was studied by cyclic voltammetry technique, and it was found that interaction predominantly takes place through intercalation mode. The selectivity of developed DNA biosensor was also explored by DPV on the basis of considering hybridisation event with non-complementary, one-base mismatched DNA and complementary target DNA sequence. Large decrease in the peak current was found upon the addition of complementary target DNA. The sensitivity of the developed DNA biosensor was also investigated, and detection limit was found to be 1.20 nmol L^?1.     

Probing the micellization kinetics of pyrene end-labeled diblock copolymer via a combination of stopped-flow light-scattering and fluorescence techniques

A pyrene end-labeled double hydrophilic diblock copolymer, poly(2-(diethylamino)ethyl methacrylate)-b-poly(2-(dimethylamino)ethyl methacrylate) (Py-PDEA-b-PDMA), was synthesized by sequential monomer addition via oxyanionic polymerization using a 1-pyrenemethanol-based initiator. This diblock copolymer exhibits reversible pH-responsive micellization behavior in aqueous solution, forming PDEA-core micelles stabilized by the soluble PDMA block at neutral or alkaline pH. Taking advantage of the pyrene probe covalently attached to the end of the PDEA block, the pH-induced micellization kinetics of Py-PDEA-b-PDMA was monitored by stopped-flow light scattering using a fluorescence detector. Upon a pH jump from 4.0 to 9.0, both the scattered light intensity and excimer/monomer fluorescence intensity ratios (IE/IM) increase abruptly initially, followed by a more gradual increase to reach plateau values. Interestingly, the IE/IM ratio increases abruptly within the first 10 ms: a triple exponential function is needed to fit the corresponding dynamic trace, leading to three characteristic relaxation time constants (tau(1,fluo) < tau(2,fluo) < tau(3,fluo)). On the other hand, dynamic traces for the scattered light intensity can be well-fitted by double exponential functions: the resulting time constants tau(1,scat) and tau(2,scat) can be ascribed to formation of the quasi-equilibrium micelles and relaxation into their final equilibrium state, respectively. Most importantly, tau(1,scat) obtained from stopped-flow light scattering is in general agreement with tau(2,fluo) obtained from stopped-flow fluorescence. The fastest process (tau(1,fluo) approximately 4 ms) detected by stopped-flow fluorescence is ascribed to the burst formation of small transient micelles comprising only a few chains, which are too small to be detected by conventional light scattering. These nascent micelles undergo rapid fusion and grow into quasi-equilibrium micelles and then slowly approach their final equilibrium state. The latter two processes can be detected by both techniques.     

Facile preparation of core‐crosslinked micelles from azide‐containing thermoresponsive double hydrophilic diblock copolymer via click chemistry

Double hydrophilic diblock copolymer, poly(N,N‐dimethylacrylamide)‐b‐poly(N‐isopropylacrylamide‐co‐3‐azidopropylacrylamide) (PDMA‐b‐P(NIPAM‐co‐AzPAM), containing azide moieties in one of the blocks was synthesized via consecutive reversible addition‐fragmentation chain transfer polymerization. The obtained diblock copolymer molecularly dissolves in aqueous solution at room temperature, and can further supramolecularly self‐assemble into core‐shell nanoparticles consisting of thermoresponsive P(NIPAM‐co‐AzPAM) cores and water‐soluble PDMA coronas above the lower critical solution temperature of P(NIPAM‐co‐AzPAM) block. As the micelle cores contain reactive azide residues, core crosslinking can be facilely achieved upon addition of difunctional propargyl ether via click chemistry. In an alternate approach in which the PDMA‐b‐P(NIPAM‐co‐AzPAM) diblock copolymer was dissolved in a common organic solvent (DMF), the core‐crosslinked (CCL) micelles can be fabricated via “click” crosslinking upon addition of propargyl ether and subsequent dialysis against water. CCL micelles prepared by the latter approach typically possess larger sizes and broader size distributions, compared with that obtained by the former one. In both cases, the obtained (CCL) micelles possess thermoresponsive cores, and the swelling/shrinking of which can be finely tuned with temperature, rendering them as excellent candidates as intelligent drug nanocarriers. Because of the high efficiency and quite mild conditions of click reactions, we expect that this strategy can be generalized for the structural fixation of other self‐assembled nanostructures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 860–871, 2008     

Developing a coarse-grained force field for the diblock copolymer poly(styrene-b-butadiene) from atomistic simulation

We have developed a coarse-grained force field for the poly(styrene-b-butadiene) diblock copolymer. We describe the computational methods and discuss how they were applied to develop a coarse-grained force field for this diblock copolymer from the atomistic simulation. The new force field contains three different bonds, four angles, five dihedral angles, and three nonbonded terms. We successfully tested this coarse-grained model against the chain properties, including static and dynamic properties, derived from the atomistic simulation; the results suggest that the coarse-grained force field is an effective model.     

Stimuli‐responsive diblock copolymer brushes via combination of “click chemistry” and living radical polymerization

pH‐ and temperature‐responsive poly(N‐isopropylacrylamide‐block?4‐vinylbenzoic acid) (poly(NIPAAm‐b‐VBA)) diblock copolymer brushes on silicon wafers have been successfully prepared by combining click reaction, single‐electron transfer‐living radical polymerization (SET‐LRP), and reversible addition‐fragmentation chain‐transfer (RAFT) polymerization. Azide‐terminated poly(NIPAAm) brushes were obtained by SET‐LRP followed by reaction with sodium azide. A click reaction was utilized to exchange the azide end group of a poly(NIPAAm) brushes to form a surface‐immobilized macro‐RAFT agent, which was successfully chain extended via RAFT polymerization to produce poly(NIPAAm‐b‐VBA) brushes. The addition of sacrificial initiator and/or chain‐transfer agent permitted the formation of well‐defined diblock copolymer brushes and free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. Ellipsometry, contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, and X‐ray photoelectron spectroscopy were used to characterize the immobilization of initiator on the silicon wafer, poly(NIPAAm) brush formation via SET‐LRP, click reaction, and poly(NIPAAm‐b‐VBA) brush formation via RAFT polymerization. The poly(NIPAAm‐b‐VBA) brushes demonstrate stimuli‐responsive behavior with respect to pH and temperature. The swollen brush thickness of poly(NIPAAm‐b‐VBA) brush increases with increasing pH, and decreases with increasing temperature. These results can provide guidance for the design of smart materials based on copolymer brushes. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2677–2685     

Mean‐field and fluctuation correction analyses for a diblock copolymer melt exhibiting an immiscibility loop

A study on a diblock copolymer melt that can form certain specific interactions between dissimilar monomers is performed first with a mean‐field approach and then with a fluctuation correction approach. Flory's interaction parameter χ possesses both enthalpic and entropic contributions because of the specific interactions. It is found that not only a lower critical ordering transition but also an immiscibility loop with an upper critical ordering transition can be developed in the copolymer by the presence of the specific interactions and the entropic component in χ. The mean‐field loop phase diagram is shown to feature a typical sequence of microphase transitions upon both heating and cooling with two continuous transition points at a symmetric composition. It is revealed that the fluctuation effects remove both continuous transition points to significantly shrink the loop. The pressure effects on the phase behavior of the copolymer are also discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1889–1896, 2003     

Syntheses and characterization of 16‐arm star and star diblock copolymer and AB8 9‐miktoarm star copolymer via NMRP and ROP from dendritic multifunctional macroinitiators

A dendritic macroinitiator having 16 TEMPO‐based alkoxyamines, Star‐16 , was prepared by the reaction of a dendritic macroinitiator having eight TEMPO‐based alkoxyamines, [G‐3]‐OH , with 4,4′‐bis(chlorocarbonyl)biphenyl. The nitroxide‐mediated radical polymerization (NMRP) of styrene (St) from Star‐16 gave 16‐arm star polymers with PDI of 1.19–1.47, and NMPR of 4‐vinylpyridine from the 16‐arm star polymer gave 16‐arm star diblock copolymers with PDI of 1.30–1.43. The ring‐opening polymerization of ε‐caprolactone from [G‐3]‐OH and the subsequent NMRP of St gave AB₈ 9‐miktoarm star copolymers with PDI of 1.30–1.38. The benzyl ether linkages of the 16‐arm star polymers and the AB₈ 9‐miktoarm star copolymers were cleaved by treating with Me₃SiI, and the resultant poly(St) arms were investigated by size exclusion chromatography (SEC). The SEC results showed PDIs of 1.23–1.28 and 1.18–1.22 for the star polymers and miktoarm stars copolymers, respectively, showing that they have well‐controlled poly(St) arms. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1159–1169, 2007.     

Fabrication of mesoporous Pt inside micrometer channels via “solvent-evaporation-mediated direct physical casting”

We have proposed a novel convenient pathway via solvent-evaporation-mediated direct physical casting (SEDPC) for the fabrication of mesoporous metals in a micrometer scale. We have presented the successful deposition of highly ordered mesoporous Pt into micrometer channels prepared by lithography. The direct observation by a high-resolution scanning microscope (HR-SEM) showed the formation of highly ordered 2D-hexagonal (p6mm) mesoporous metals onto such substrates. The cyclic voltammogram of the mesoporous Pt in sulfuric acid revealed a typical feature which can identify the clean Pt surface. Moreover, mesoporous Pt exhibits an effective reduction of dissolved dioxygen molecules. It is proved that mesoporous Pt deposited in a very confined area via the SEDPC method possesses electrocatalytic performance owing to Pt.     

Self-assembly of a diblock copolymer with pendant disulfide bonds and chromophore groups: a new platform for fast release

An amphiphilic block copolymer comprising poly(ethylene glycol) (PEG) and poly(2-(methacryloyl)oxyethyl-2'-hydroxyethyl disulfide) (PMAOHD) blocks was synthesized by atom transfer radical polymerization (ATRP). Pyrenebutyric acid was conjugated to the block copolymer by esterification, and a block copolymer with pendant disulfide bonds and pyrenyl groups (PEG-b-P(MAOHD-g-Py)) was obtained. (1)H NMR and gel permeation chromatography (GPC) results demonstrated the successful synthesis of the block copolymer. The cleavage of the disulfide bonds and the degrafting of the pyrenyl groups were investigated in THF and a THF/methanol mixture. Fluorescence spectroscopy, GPC, and (1)H NMR results demonstrated fast cleavage of the disulfide bonds by Bu(3)P in THF. Fluorescence results showed the ratio of the intensity of the excimer peak to the monomer peak decreased rapidly within 20 min. GPC traces of the block copolymer moved to a long retention time region after addition of Bu(3)P, indicating the cleavage of the disulfide bonds and the degrafting of the pyrenyl groups. PEG-b-P(MAOHD-g-Py) can self-assemble into micelles with poly(MAOHD-g-Py) cores and PEG coronae in a mixture of methanol and THF (9:1 by volume). The dissociation of the micelles in the presence of Bu(3)P was investigated. After cleavage of the disulfide bonds in the micellar cores, a pyrene-containing small molecular compound and a block copolymer with pendant thiol groups were produced. Transmission electron microscopy (TEM), dynamic light scattering (DLS), and (1)H NMR were employed to track the dissociation of the polymeric micelles. All the techniques demonstrated the dissociation of the micelles and the fast release of pyrenyl groups from the micelles.