甲醇是极氧化的现场FTIR透射差谱研究

利用现场透射红外差谱方法研究了在无水1mol/LiClO~4甲醇溶液中甲醇在Pt电极上的阳极氧化。实验采用了细网格Pt电极和薄层电解池。各电位下的FTIR透射差谱反映了溶液中电极反应的变化。结果表明甲醇可被氧化成甲醛,且随电位的提高可进一步氧化成甲酸甲酯。     

Pt及其修饰电极上甲醇吸附和氧化的CV和EQCM研究

运用电化学循环伏安和石英晶体微天平 (EQCM )研究了 0 .1mol·L- 1H2 SO4 溶液中甲醇在Pt电极和以Sb ,S不可逆吸附原子修饰的Pt(Pt/Sbad和Pt/Sad)电极上的吸附和氧化过程 .结果表明甲醇的氧化与电极表面氧物种有着极其密切的关系 .Pt电极表面Sb吸附原子能在较低的电位下吸附氧 ,可显著提高甲醇电催化氧化活性 .与Pt电极相比较 ,Sb吸附原子修饰的Pt电极使甲醇氧化的峰电位负移了 0 .13V .相反 ,Pt电极表面S吸附原子的氧化会消耗表面氧物种 ,抑制了甲醇的电氧化 .本文从表面质量变化提供了吸附原子电催化作用的新数据     

甲醇在欠电位沉积Ru修饰Pt电极上的催化氧化

采用欠电位沉积(upd)方法在Pt 表面沉积亚单层的Ru制备出upd-Ru/Pt 电极. 通过欠电位沉积前后电极在0.5 mol·L-1 H2SO4溶液中循环伏安图-152 - 128 mV(vs Ag/AgCl)电位范围内对氢区的数值积分确定Pt表面Ru 的覆盖度. 用电化学方法测试了甲醇在upd-Ru/Pt电极上的催化氧化, 并讨论分析了欠电位沉积电位和Ru的表面覆盖度对甲醇氧化的影响. 结果表明, Ru能够欠电位沉积到Pt表面. Pt表面欠电位沉积少量的Ru 即能大大促进甲醇的氧化.只要控制upd-Ru的沉积量, upd-Ru原子就能大大促进甲醇氧化而与沉积电位无关. Ru原子对甲醇氧化的促进作用与Ru和Pt是否形成合金无关, 而取决于Ru 在Pt表面的百分含量.     

甲醇在欠电位沉积Sn/Pt电极上催化氧化

在欠电位沉积（upd）锡修饰的铂电极（upd-Sn/Pt）上,对甲醇电化学催化氧化过程进行了研究.发现当Pt表面upd-Sn的覆盖率在20％附近时,对甲醇的催化氧化的增强作用最为明显；在电位低于0.35 V （vs RHE）时,甲醇在Pt与upd-Sn/Pt电极上氧化只进行到脱氢生成CO的步骤;在0.35 V以后,表面Sn－OH形成,反应Sn－OH＋COads=Sn＋CO2＋H＋＋e有利于表面CO的去除;而Pt电极上,只有0.6 V以后,才有反应Pt－OH＋COads=Pt＋CO2＋H＋＋e发生.因此,Sn的存在有利于甲醇在较低的电位下氧化; Pt电极上CH3OH脱氢并释放出电子的过程是一个快速的过程,表面CO的去除是甲醇氧化过程的控制步骤;甲醇氧化产生的表面吸附态CO 以线式吸附为主,少量的桥式吸附态CO在反应初期即达到吸附饱和; Pt表面上upd-Sn表现的催化增强作用,在光亮铂电极和在高分散铂黑电极上是一致的.     

Pt-Ru/GC电极对甲醇电催化氧化的研究

利用循环伏安法制备了Pt-Ru/GC电极并用于对甲醇的电催化氧化研究,考察了Pt、Ru原子比、沉积电位下限和沉积量对电极催化性能的影响,研究了电极催化性能的稳定性。结果表明Ru的加入对电极催化性能具有明显的改善作用,对甲醇的氧化电位范围明显变宽,氧化电流明显增大,电极的稳定性明显高于Pt/GC电极。在Pt、Ru原子比为1:1、沉积电位下限为-0.2V、沉积量为40r的条件下,Pt-Ru/GC电极对甲醇电催化氧化的性能最好。     

Pt电极上吸附原子对仲丁醇电催化氧化性能的影响

运用电化学循环伏安和石英晶体微天平研究了HClO4溶液中仲丁醇在Pt电极及以Sb和S吸附原子修饰的Pt(Pt/Sbad和Pt/Sad)电极上的电催化氧化过程 .从电极表面质量变化可以看出 ,仲丁醇的氧化与电极表面的氧物种有着极其密切的关系 .Pt电极表面Sb吸附原子可在较低的电位下吸附氧 ,明显提高仲丁醇的氧化活性 .与Pt电极相比 ,Sb吸附原子修饰的Pt电极使仲丁醇氧化的峰电位负移约 10 0mV .相反 ,Pt电极表面S吸附原子的氧化会消耗表面氧物种 ,抑制仲丁醇的氧化 .从电极表面质量变化提供了吸附原子电催化作用的数据     

Pt-Mo电极上CO、甲醛和甲醇的电催化氧化-微分电化学质谱研究

利用微分电化学质谱（DEMS）研究了Mo修饰的Pt电极上CO、甲醛和甲醇的电催 化氧化,证实了Mo(IV)是催化活性样品,而且它只对弱吸附CO的氧化起催化作用, 对强吸附CO的氧化没有催化活性。在低于0.4 V的电位下,吸附在Pt电极上的Mo结 甲醇和甲醛的催化氧化是通过弱吸附CO的氧化路径进行的。     

利用原位红外光谱与微分电化学质谱联用技术研究在Pt以及PtRu电极上发生的甲醇氧化反应

利用电化学衰减全反射原位傅里叶变换红外光谱与微分电化学质谱联用技术,在流动电解池环境以及恒电位条件下研究了Pt电极和Pt电极通过表面电沉积Ru形成的PtRu电极（PtxRuy）上发生的甲醇氧化反应（反应电解质溶液为0.1 mol/L HClO4＋0.5 mol/L MeOH）. 在0.3-0.6 V（参比电极为可逆氢参比）实验用到的所有电极上,CO是唯一能从红外光谱观察到的与甲醇相关的表面吸附物;在Pt0.56Ru0.44电极上可以观察到CO吸附在Ru原子形成的岛上和CO线式吸附在Pt电极表面红外波段,而其他电极上只能观察到Pt表面上线式吸附的CO;甲醇氧化活性按Pt0.73Ru0.27〉Pt0.56Ru0.44〉Pt0.83Ru0.17〉Pt的顺序递减;在0.5V时,甲醇在Pt0.73Ru0.27电极上的氧化反应的CO2电流效率达到了50%.     

Pt-Mo电极上CO、甲醛和甲醇的电催化氧化-微分电化学质谱研究

利用微分电化学质谱（DEMS）研究了Mo修饰的Pt电极上CO、甲醛和甲醇的电催 化氧化，证实了Mo(IV)是催化活性样品，而且它只对弱吸附CO的氧化起催化作用， 对强吸附CO的氧化没有催化活性。在低于0.4 V的电位下，吸附在Pt电极上的Mo结 甲醇和甲醛的催化氧化是通过弱吸附CO的氧化路径进行的。     

Pt-Mo2C/GC催化甲醇氧化的现场电化学-红外光谱研究

应用离子交换法制备了40%Pt在Mo2C/GC上的电催化剂.X射线衍射(XRD)显示,Pt在Mo2C载体上有较好的分散度,平均粒径为3 nm.循环伏安、计时电位测试表明,酸性溶液中,Pt-Mo2C/GC具有良好的甲醇氧化性能.其催化甲醇氧化的起始电位比Pt/C的负移了90 mV.这一优异性能与Pt和载体Mo2C之间的协同作用有关.现场红外光谱电化学测量显示,甲醇在Pt/C电极氧化的中间产物是桥式吸附COB和线性吸附COL,而在Pt-Mo2C/GC电极则未检测到有害中间产物CO,其氧化终产物均为CO2.     

In situ transmission difference FTIR spectroscopic investigation on anodic oxidation of methanol in aqueous solution

In situ transmission difference FTIR spectroscopy method was introduced for studying the anodic oxidation of methanol in acid aqueous solution. A minigrid Pt optically transparent thin layer electrode was used as working electrode. This method has the ability to clarify the identity of species involved in the oxidation process both in solution and adsorbed at the surface of electrode. From the results of in situ transmission difference FTIR spectroscopy measurement it was found that HCHO, HCOOH, HCOOCH₃ and CH₂(OCH₃)₂ could be formed in the oxidation process of methanol. The final product was CO₂. The adsorbed poisonous intermediate CO was detected. It was formed at near 0.6 V and became significant at 0.9 V, where the oxidation current was inhibited. The in situ transmission difference FTIR spectroscopy method is a very convenient, relative simplicity and efficient method for investigating the electrochemical process, and could be as a good candidate for further application.     

Electrooxidation of methanol on upd-Ru and upd-Sn modified Pt electrodes

The electrochemical oxidation of methanol has been investigated on underpotentially deposited-ruthenium-modified platinum electrode (upd-Ru/Pt) and on underpotentially deposited-tin-modified platinum electrode (upd-Sn/Pt). The submonolayers of upd-Ru and upd-Sn on a Pt electrode increased the rate of methanol electrooxidation several times as large as that on a pure Pt electrode. The best performance for methanol electrooxidation was obtained on a ternary platinum based catalyst modified by upd-Ru and upd-Sn simultaneously. The influence of the submonolayers of upd-Ru adatoms and upd-Sn adatoms on the oxidation of methanol in acid has been investigated. The effect of Ru on methanol electrooxidation lies on the distribution of Ru adatoms on a Pt surface. It has been shown that as long as the amount of upd-Ru deposits were controlled in a proper range, upd-Ru deposits would enhance the methanol oxidation obtained on a Pt electrode at whichever deposition potential the upd-Ru deposits were obtained. The effects of tin are sensible to the potential range. The enhancement effect of upd-Sn adatoms for the oxidation of methanol will disappear as the electrode potential is beyond a certain value. It is speculated that there exists a synergetic effect on the Pt electrode as adatoms Ru and Sn participate simultaneously in the methanol oxidation.     

Nickel foam-based composite electrodes for electrooxidation of methanol

Nickel foam and five nickel foam-based composite electrodes were prepared for being used as anode materials for the electrooxidation of methanol in KOH solution containing 0.1 and 1.0 M of methanol. The layered electrodes composed of nickel foam, platinum nanoparticles, polyaniline (PANI) and/or porous carbon (C) prepared in various assemblies. As shown by SEM analysis, depending on the preparation conditions, the electrodes of different morphologies were obtained. Using the cyclic voltammetry method, the oxidation of methanol on nickel foam electrode was observed in the potential range 0.4 V ↔ 0.7 V, where the Ni(OH)₂/NiOOH transformation occurred. The presence of Pt particles in electrode gave rise to the increase in electrocatalytic activity in this potential range. For electrodes containing dispersed platinum catalyst (Ni/Pt, Ni/PANI/Pt and Ni/C/Pt), the oxidation of methanol was noted also in the potential range −0.5 V ↔ 0.1 V. The electrocatalytic activities of the examined electrodes toward methanol oxidation at low potentials were in order Ni/Pt > Ni/C/Pt > Ni/PANI/Pt, whereas at high potentials in order Ni/PANI/Pt > Ni/Pt> Ni/C/Pt > Ni. Among the examined electrodes, the most resistant to cyclic poisoning appeared to be the Ni/C/Pt electrode. Presented at the 4Th Baltic Conference on Electrochemistry, Greifswald, March 13–16, 2005     

磷钼酸修饰的铂电极对二甲醚氧化的电催化作用

利用循环伏安扫描法制备了磷钼酸(H3PMo12O40)修饰的铂电极.在制备修饰电极时,随着扫描次数的增加,磷钼酸的氧化还原峰电流增大,但最终获得稳定的重现性好的磷钼酸修饰的铂电极.通过循环伏安法研究了该修饰电极对二甲醚氧化的电催化反应.结果表明,与未修饰的铂电极相比,磷钼酸修饰的铂电极电催化氧化二甲醚的起始氧化电位负移50 mV,氧化峰电位负移35 mV,氧化峰电流密度提高了1.86倍,这表明修饰电极的电催化活性有了很大的提高.同时,电位负扫时,二甲醚在425 mV(vsSCE)处出现氧化峰,表明二甲醚在修饰电极上的电氧化机理可能发生了改变.实验还发现,制备修饰电极时,降低扫速会提高还原物质杂多蓝的吸附量,但过多的修饰物质会降低铂的活性位数目,反而降低了对二甲醚氧化的电催化作用.     

Electrocatalytic oxidation of methanol onto platinum particles decorated nanostructured poly (1,5-diaminonaphthalene) film

In this work, platinum particles decorated nanostructured poly (1,5-diaminonaphthalene) modified glassy carbon electrode (Pt/Nano-PDAN/MGCE) is prepared. The composite catalysts are characterized by scanning electron microscopy, energy dispersive spectroscopy, and electrochemical methods. The electrochemical methanol oxidation reaction is studied at the surface of this modified electrode. At same Pt loading, the Pt/Nano-PDAN/MGCE can act as higher efficient catalyst for methanol oxidation than that Pt/MGCE. Then, the influence of some parameters such as potential scan rates, switching potential, and methanol concentration on its oxidation as well as long-term stability of the modified electrode have studied by electrochemical methods. Also, ability of the modified electrode toward electrocatalytic oxidation of formaldehyde as an intermediate in methanol oxidation has been investigated.     

Electrocatalytic activity of porous nanostructured Fe/Pt-Fe electrode for methanol electrooxidation in alkaline media

An electrochemical approach to fabricate a nanostructured Fe/Pt-Fe catalyst through electrodepo-sition followed by galvanic replacement is presented. An Fe/Pt-Fe nanostructured electrode was prepared by deposition of Fe-Zn onto a Fe electrode surface, followed by replacement of the Zn by Pt at open-circuit potential in a Pt-containing alkaline solution. Scanning electron microscopy and energy-dispersive X-ray techniques reveal that the Fe/Pt-Fe electrode is porous and contains Pt. The electrocatalytic activity of the Fe/Pt-Fe electrode for oxidation of methanol was examined by cyclic voltammetry and chronoamperometry. The electrooxidation current on the Fe/Pt-Fe catalyst is much higher than that on flat Pt and smooth Fe catalysts. The onset potential and peak potential on the Fe/Pt-Fe catalyst are more negative than those on flat Pt and smooth Fe electrodes for methanol electrooxidation. All results show that this nanostructured Fe/Pt-Fe electrode is very attractive for integrated fuel cell applications in alkaline media.     

Pt/C电极表面活化处理对乙醇电催化氧化的影响

0引言直接甲醇燃料电池(DMFC)由于其燃料来源丰富、价格低廉、甲醇携带和储存安全方便等独特的优越性而越来越受到重视[1]。但DMFC中常用的阳极Pt催化剂对甲醇氧化的低的电催化活性及易于被甲醇氧化的中间体,吸附态的CO(COad)毒化的问题一直是制约DMFC走向实用化的关键问题[2,3]。由于甲醇分子小,在质子交换膜上有较大的透过作用,并且甲醇具有较高的毒性,所以寻求甲醇的替代燃料也是一直以来被广泛关注的问题[4,5]。乙醇是最简单的链醇分子,相对于甲醇来说,乙醇有很多优点,乙醇基本上没有毒性,来源丰富,价格可与甲醇竞争,能量密度高…     

Voltammetry in Undiluted Acetic Acid. In Situ Determination of Water

Water present in undiluted acetic acid can be monitored in situ with Pt and Au microelectrodes using differential pulse and square‐wave voltammetries. Both reduction and oxidation peaks can be obtained. The best quantitative analytical results were obtained for the anodic peak, the Pt microelectrode, and differential pulse voltammetry. The anodic water peak is located at +1.55 V vs. the quasi reference Pt electrode. The voltammetric peak obtained at Pt electrode is apparently not a diffusional one, however, the calibration plot obtained by employing this peak is linear over a wide concentration range, up to 4 mol dm^?3. The detection limit has been estimated as 2.3 mM or 0.0043 v/v%. The developed method may be particularly useful, since the Karl Fischer method can not be used to determine water in glacial acetic acid due to the estrification reaction of acetic acid with methanol. A voltammetric wave of undiluted acetic acid could not be obtained in the positive and negative ranges of potential.     

多孔纳米结构Fe/Pt-Fe电极对碱性介质中甲醇电氧化的催化活性（英文）

An electrochemical approach to fabricate a nanostructured Fe/Pt-Fe catalyst through electrodeposition followed by galvanic replacement is presented. An Fe/Pt-Fe nanostructured electrode was prepared by deposition of Fe-Zn onto a Fe electrode surface, followed by replacement of the Zn by Pt at open-circuit potential in a Pt-containing alkaline solution. Scanning electron microscopy and energy-dispersive X-ray techniques reveal that the Fe/Pt-Fe electrode is porous and contains Pt. The electrocatalytic activity of the Fe/Pt-Fe electrode for oxidation of methanol was examined by cyclic voltammetry and chronoamperometry. The electrooxidation current on the Fe/Pt-Fe catalyst is much higher than that on flat Pt and smooth Fe catalysts. The onset potential and peak potential on the Fe/Pt-Fe catalyst are more negative than those on flat Pt and smooth Fe electrodes for methanol electrooxidation. All results show that this nanostructured Fe/Pt-Fe electrode is very attractive for integrated fuel cell applications in alkaline media.