Simultaneous determination of iron and ruthenium by preconcentration on sulfopropyl sephadex cation exchanger

A new method for the simultaneous determination of iron and ruthenium at ultra-trace levels is proposed. The method is based on the formation of the iron and ruthenium complexes with 2,4,6-tri-(2-pyridil)-1,3,5-triazine (TPTZ) in the presence of hydroxylamine hydrochloride and buffer CH₂ClCOOH/CH₂ClCOONa (pH=3.0). The formation of the complexes and their retention on a cationic resin SP-Sephadex C25 were integrated in one step at 90 °C, with stirring for 90 min. Under these conditions a high preconcentration level was achieved for both analytes. The complexes retained on the solid phase were evaluated by second derivative spectrophotometry. The selected analytical wavelengths were 539.7 and 553.3 nm for the determination of ruthenium and iron, respectively, by using the zero crossing approach. The detection and quantification limits were 0.54 ng ml⁻¹ and 1.79 ng ml⁻¹ for ruthenium and 0.41 ng ml⁻¹ and 1.38 ng ml⁻¹ for iron. The proposed method was applied to the determination of both analytes in synthetic mixtures.     

Determination of cobalamins (hydroxo-, cyano-, adenosyl- and methyl-cobalamins) in seawater using reversed-phase liquid chromatography with diode-array detection

A high-performance liquid chromatography method was developed for the separation and determination of four cobalamins in seawater. Chromatographic separation was performed on a reversed-phase discovery RP-amide C₁₆ column with buffer potassium dihydrogenphosphate and acetonitrile as the mobile phases in linear gradients elution mode. Cobalamins were previously preconcentrated in C₁₈ resins cartridges. Detection was performed using UV-diode array detector in a range of λ of 200–400 nm. The method showed to be linear over a range of 1–300 ng mL⁻¹ with acceptable precision and accuracy. The detection limits ranged between 0.07 pg mL⁻¹ for 5′-deoxyadenosylcobalamin and 0.5 pg mL⁻¹ for hydroxocobalamin. The mean cobalamins recoveries for direct determination ranged between 76 and 93% for hydroxo-, cyano- and methylcobalamin, while the recovery for 5′-deoxyadenosylcobalamin was only 31% suggesting that the preconcentration method was not valid for this cobalamin. The method was successfully applied to coastal seawater where the concentrations ranged from 4.2 to 7.3 ng L⁻¹ for hydroxo-, 1.4–3.9 ng L⁻¹ for cyano-, 2.1–4.6 ng L⁻¹ for 5′-deoxyadenosyl- and 33–83.5 ng L⁻¹ for methylcobalamin.     

On-line preconcentration and determination of cobalt by chelating microcolumns and flow injection atomic spectrometry

A simple and sensitive flow injection analysis-atomic absorption spectrometric procedure is described for the determination of cobalt. The method is based upon on-line preconcentration of cobalt on a microcolumn of 2-nitroso-1-naphthol immobilized on surfactant coated alumina. The trapped cobalt is then eluted with ethanol (250 μl) and determined by flame atomic absorption spectrometry. The analytical figures of merit for the determination of cobalt are as follows: detection limit (3 S), 0.02 ng ml⁻¹; precision (RSD), 2.8% for 20 ng ml⁻¹ and 1.7% for 70 ng ml⁻¹ of cobalt; enrichment factor, 125 (using 25 ml of sample). The method has been applied to the determination of cobalt in water samples, vitamin B₁₂ and B-complex ampoules and accuracy was assessed through recovery experiment and independent analysis by furnace AAS.     

Analysis of trace levels of domoic acid in seawater and plankton by liquid chromatography without derivatization,using UV or mass spectrometry detection

Quantitation of trace levels of domoic acid (DA) in seawater samples usually requires labour-intensive protocols involving chemical derivatization with 9-fluorenylmethylchloroformate and liquid chromatography with fluorescence detection (FMOC–LC–FLD). Procedures based on LC–MS have been published, but time-consuming and costly solid-phase extraction pre-concentration steps are required to achieve suitable detection limits. This paper describes an alternative, simple and inexpensive LC method with ultraviolet detection (LC–UVD) for the routine analysis of trace levels of DA in seawater without the use of sample pre-concentration or derivatization steps. Qualitative confirmation of DA identity in dubious samples can be achieved by mass spectrometry (LC–MS) using the same chromatographic conditions. Addition of an ion-pairing/acidifying agent (0.15% trifluoroacetic acid) to sample extracts and the use of a gradient elution permitted the direct analysis of large sample volumes (100 μl), resulting in both high selectivity and sensitivity (limit of detection = 42 pg ml⁻¹ by LC–UVD and 15 pg ml⁻¹ by LC–MS). Same-day precision varied between 0.4 and 5%, depending on the detection method and DA concentration. Mean recoveries of spiked DA in seawater by LC–UVD were 98.8% at 0.1–10 ng ml⁻¹ and 99.8% at 50–1000 ng ml⁻¹. LC–UVD exhibited strong correlation with FMOC–LC–FLD during inter-laboratory analysis of Pseudo-nitzschia multiseries cultures containing 60–2000 ng DA ml⁻¹ (r² > 0.99), but more variable results were obtained by LC–MS (r² = 0.85). This new technique was used to confirm the presence of trace DA levels in low-toxicity Pseudo-nitzschia spp. isolates (0.2–1.6 ng ml⁻¹) and in whole-water field samples (0.3–5.8 ng ml⁻¹), even in the absence of detectable Pseudo-nitzschia spp. cells in the water column.     

Spectrophotometric study of Cd(II), Pb(II), Hg(II) and Zn(II) complexes with 5,10,15,20-tetrakis(4-carboxylphenyl)porphyrin

The reaction of 5,10,15,20-tetrakis(4-carboxylphenyl)porphyrin (TCPP) with Cd(II), Pb(II), Hg(II) and Zn(II) was studied spectrophotometrically and kinetics, equilibrium constants as well as photodecomposition of complexes were determined. It was verified that these metal ions with large radius accelerate the incorporation reaction of zinc into TCPP. On the basis of the mechanism and kinetics of this reaction, a sensitive method for the spectrophotometric determination of trace amounts of Zn(II) has been developed. The molar absorptivity of examined Zn-TCPP complex and Sandell's sensitivity at 423 nm were 3.5×10⁵ M⁻¹ cm⁻¹ and 18.3 ng cm⁻². The detection limit for the recommended procedure was 1.4×10⁻⁹ M (0.9 ng ml⁻¹) and precision in range 20-100 ng ml⁻¹ not exceeds 2.7% RSD. The proposed method applied for zinc determination in natural waters and nutritional supplement was compared with AAS results and declared value.     

Integrated retention/spectrophotometric detection in flow-injection analysis : Determination of Iron in Water and Wine

An integrated retention/spectrophotometric method is proposed for the determination of iron based on the Fe (III)-thiocyanate complex. The method has good selectivity, with a determination limit of 10 ng ml^?1 and a linear range of 10–400 ng ml^?1. Different types of measurements (peak height, absorbance increment, tangent curve) are shown to have their particular advantages. The method is applied to the determination of iron in natural water and wine, with an average recovery of 100.3% and 98.8% and an average deviation of the recovery of 2.5% and 1.6%, respectively.     

Flow-injection spectrophotometry of vanadium by catalysis of the bromate oxidation of N,N'-bis(2-hydroxyl-3-sulfopropyl)-tolidine

A highly sensitive flow-injection method is proposed for the catalytic determination of vanadium(V) at sub-nanogram per milliliter levels using a new indicator reaction. The method is based on the catalytic effect of vanadium(V) on the bromate oxidation of N,N′-bis(2-hydroxyl-3-sulfopropyl)-tolidine. 1,2-Dihydroxybenzene-3,5-disulfonate was used as an activator in the vanadium(V)-catalyzed reaction and significantly enhanced the sensitivity of the method. Vanadium(V) in the range 0.01-3.0 ng ml⁻¹ was easily determined with sampling rate of about 30 h⁻¹. Vanadium(IV) could be also determined. The limit of detection (S/N=3) was 0.008 ng ml⁻¹ and the relative standard deviations were 1.4 and 1.6% for ten determinations of 0.2 ng ml⁻¹ vanadium(IV) and vanadium(V), respectively. Interferences from metal ions could be suppressed by the addition of ethylenediamine-N,N,N′,N′-tetrakis(methylenephosphonic acid) as a masking agent. The proposed method was successfully applied to the determination of vanadium in water samples.     

A novel needle trap sorbent based on carbon nanotube-sol-gel for microextraction of polycyclic aromatic hydrocarbons from aquatic media

A new type of composite material based on carbon nanotubes (CNTs) and sol–gel chemistry was prepared and used as sorbent for needle trap device (NTD). The synthesized composite was prepared in a way to disperse CNTs molecules in a sol–gel polymeric network. CNT/silica composites with different CNT doping levels were successfully prepared, and the extraction capability of each composite was evaluated. Effects of surfactant and the oxidation duration of CNTs on the extraction efficiency of synthesized composites were also investigated. The applicability of the synthesized sorbent was examined by developing a method based on needle trap extraction (NTE) and gas chromatography mass spectrometry detection (GC–MS) for the determination of polycyclic aromatic hydrocarbons (PAHs) in aqueous samples. Important parameters influencing the extraction process were optimized and an extraction time of 30 min at 50 °C and sampling flow rate of 2.5 mL min⁻¹ gave maximum peak area, when NaCl (15%, w/v) was added to the aqueous sample. The linearity for acenaphthene, acenaphthylene and fluorene was in the concentration range of 0.01–20 ng mL⁻¹ and for naphthalene and anthracene was in the range of 0.1–50 ng mL⁻¹. Limits of detection was 0.001 ng mL⁻¹, for acenaphthene, acenaphthylene and fluorene, and 0.01 ng mL⁻¹, for naphthalene and anthracene using time-scheduled selected ion monitoring (SIM) mode, and the RSD% values (n = 3) were all below 11.2% at the 1 ng mL⁻¹ level. The developed method was successfully applied to real water samples while the relative recovery percentages obtained for the spiked water samples were from 73.8 to 113.8%.     

Solid phase preconcentration of iron as methylthymol blue complex on naphthalene-tetraoctylammonium bromide adsorbent with subsequent flame atomic absorption determination

A sensitive and selective preconcentration method for the determination of trace amounts of iron by atomic absorption spectrometry has been developed. Iron forms a complex with methylthymol blue at pH=3. This complex is retained by naphthalene tetraoctylammonium bromide adsorbent in a column with a height of about 2 cm. The adsorbed metal complex is then eluted from the column with nitric acid and its iron content is determined by flame atomic absorption spectrometry (FAAS). The effect of different variables such as pH, reagent concentration, flow rate and interfering ions on the recovery of the analyte was investigated. The calibration graph was linear in the range 25-350 ng ml⁻¹ of iron in the initial solution with r=0.9994. The limit of detection based on 3S_b criterion was 12 ng ml⁻¹ and the relative standard deviation for eight replicate measurements of 150 and 300 ng ml⁻¹ of iron was 3.1 and 1.8%, respectively. This procedure was successfully applied to the determination of iron in tap and sewage water samples.     

The use of carbon nanofibers microcolumn preconcentration for inductively coupled plasma mass spectrometry determination of Mn,Co and Ni

Based on carbon nanofibers (CNFs) as a solid phase extraction adsorbent, a microcolumn preconcentration method coupled to inductively coupled plasma mass spectrometry (ICP–MS) was developed for the determination of trace elements (Mn, Co and Ni). The effect of various experimental parameters such as pH, sample flow rate and volume, elution solution and interfering ions on the retention of the studied ions have been investigated systematically. During all the steps of the experimental process, Mn, Co and Ni could be quantitatively sorbed on the microcolumn containing CNFs in the range of pH 6.0–9.0, and then eluted completely with 0.5 mol ml^− 1 HNO₃. A preconcentration factor of 150-fold was obtained. The detection limits for Mn, Co and Ni were 40, 0.4 and 8.0 pg ml^− 1, respectively, with relative standard deviations less than 6.0%. In order to validate the proposed method, two certified reference materials of human hair (GBW 07601) and mussel (GBW 08571), and water sample were analyzed with satisfactory results. The recoveries were between 95.0 and 114%.     

Combined liquid chromatography-coulometric detection and microextraction by packed sorbent for the plasma analysis of long acting opioids in heroin addicted patients

The sublingual combination of buprenorphine and naloxone (Suboxone^®) and Methadone Maintenance Therapy have been found effective in treating heroin addiction. A new analytical method suitable for the simultaneous determination of buprenorphine, norbuprenorphine, methadone and naloxone in human plasma by means of liquid chromatography with coulometric detection has been developed. The chromatographic separation was achieved with a phosphate buffer–acetonitrile mixture as the mobile phase on a cyano column. The monitoring cell of the coulometric detector was set at an oxidation potential of +0.600 V. A rapid clean-up procedure of the biological samples using a microextraction by packed sorbent technique has been implemented, employing a C8 sorbent inserted into a syringe needle. The extraction yield values were satisfactory for all analytes (>85%). The calibration curves were linear over a range of 0.25–20.0 ng mL⁻¹ for buprenorphine and norbuprenorphine, 3.0–1000.0 ng mL⁻¹ for methadone and 0.13–10.0 ng mL⁻¹ for naloxone. The sensitivity was also high with limits of detection of 0.08 ng mL⁻¹ for both buprenorphine and norbuprenorphine, 0.9 ng mL⁻¹ for methadone and 0.04 ng mL⁻¹ for naloxone. The intraday and interday precision data were always satisfactory.The method was successfully applied to plasma samples obtained from former heroin addicts treated with opioid replacement therapy.     

Differential pulse cathodic stripping adsorption voltammetric determination of trace amounts of lead using factorial design for optimization

A sensitive cathodic stripping voltammetric method is developed for determination of lead(II), with adsorptive collection of complexes with Pyrogallol red (PGR) on to a hanging mercury drop electrode. After accumulation of the complex at −0.80 V vs. Ag/AgCl reference electrode, the potential is scanned in a negative direction from −0.20 to −0.50 V with differential pulse method. Then the reduction peak current for the lead(II)-PGR complex is measured at −0.39 V. The influence of reagent and instrumental variables was completely studied by factorial design analysis. The optimum analytical conditions for the determination of lead(II) were established. Under optimum conditions, lead(II) determined in the range of 0.1-30.0 ng ml⁻¹ with a limit of detection of 0.06 ng ml⁻¹. The method is successfully applied to determination of lead(II) in water sample.     

Determination of phthalate esters in water samples by ionic liquid cold-induced aggregation dispersive liquid-liquid microextraction coupled with high-performance liquid chromatography

A novel method, termed ionic liquid cold-induced aggregation dispersive liquid–liquid microextraction (IL-CIA-DLLME), combined with high-performance liquid chromatography (HPLC) was developed for the determination of three phthalate esters in water samples. Several important parameters influencing the IL-CIA-DLLME extraction efficiency, such as the type of extraction and disperser solvent, the volume of extraction and disperser solvent, temperature, extraction time and salt effect, were investigated. Under optimal extraction conditions, the enrichment factors and extraction recoveries ranged from 174 to 212 and 69.9 to 84.8%, respectively. Excellent linearity with coefficients of correlation from 0.9968 to 0.9994 was observed in the concentration range of 2–100 ng mL⁻¹. The repeatability of the proposed method expressed as relative standard deviations ranged from 2.2 to 3.7% (n = 5). Limits of detection were between 0.68 and 1.36 ng mL⁻¹. Good relative recoveries for phthalate esters in tap, bottled mineral and river water samples were obtained in the ranges of 91.5–98.1%, 92.4–99.2% and 90.1–96.8%, respectively. Thus, the proposed method has excellent potential for the determination of phthalate esters in the environmental field.     

Spectrophotometric determination of trace lead in water after preconcentration using mercaptosephadex

A highly sensitive and selective spectrophotometric method for determination of trace lead in water after pre-concentration using mercaptosephadex (MS-50) has been developed, the method based on the color reaction of lead(II) with dibromohydroxylphenylporphyrin. Under optimal condition, lead(II) reacts with the reagent to form a 1:2 yellow complex in presence of TritonX-100, which has a maximum absorption peak at 479 nm. The color reaction can complete rapidly and remain stable for 24 h in room temperature. The molar absorption coefficient of the lead complex, the limit of quantification, the limit of detection and relative standard deviations were found to be 2.35×10⁵ l mol⁻¹ cm⁻¹, 4.3, 1.4 ng ml⁻¹ and 1.0%, respectively. The absorbance of the lead complex at 479 nm is linear up to 0.48 μg ml⁻¹ of lead(II). The effect of various co-existing ions in water were examined seriously. No interference was observed. Moreover, a simple pre-concentration method for trace lead in water was also studied using MS-50. It was found that trace lead in water can be adsorbed in 1.0 mol l⁻¹ HCl and dissociated from MS-50 with 4.0 mol l⁻¹ HCl quantitatively, that improves the selectivity and the sensitivity of method (its detection limit (3 s) changed into 0.2 ng ml⁻¹ of lead) obviously. The proposed method has been applied to determine trace lead in water samples with satisfactory results.     

Hollow fiber supported liquid membrane extraction for ultrasensitive determination of trace lead by portable tungsten coil electrothermal atomic absorption spectrometry

Hollow fiber supported liquid membrane extraction (HF-SLME) was used to separate and enrich trace lead from a large volume of 250 mL water sample to a final tiny volume of 30 μL of 1-octanol, 5 μL of which was inject into a tungsten coil electrothermal atomic absorption spectrometer (W-coil ET-AAS) for determination of lead. Some important parameters that influenced the extraction and determination were investigated in detail, such as the concentration of ammonium pyrrolidine dithiocarbamate (APDC), pH of sample solution, stirring rate, extraction time, pyrolysis current, atomization current, carrier gas flow rate, as well as interferences. Under the optimized conditions, a practical enrichment factor of 499 and a limit of detection (3σ) of 0.2 ng mL^{− 1} were obtained. The calibration curve was linear in the range of 0.5–10 ng mL^{− 1}. The relative standard deviation (RSD) was 5.6% for five measurements of a 4 ng mL^{− 1} lead standard solution. The accuracy of this method was examined by the analysis of certified reference water samples (GBW(E)080398 and GSBZ(E) 50009-88) for lead. Finally, the proposed method was applied to the determination of lead in local tap water, pond water and river water, with recoveries in the range of 96–109% for spiked samples.     

Spectrophotometric determination of molybdenum based on charge transfer complexes sensitized by copper(II)

A new high sensitive spectrophotometric determination of trace molybdenum was investigated. The sensitivity of the determination of molybdenum, which based on the color charge transfer complex of molybdotungstophosphate-3,3′,5,5′-tetramethylbenzidine, was greatly enhanced by copper(II) ions in the presence of polyvinyl alcohol. The improved method maintained the features of simplicity, rapidity and selectivity, especially eliminating the interference from tungsten. Under the optimum conditions, Beer's law was obeyed over the range from 2 to 32 ng ml⁻¹ molybdenum with molar absorptivity being 4.92×10⁵ l mol⁻¹ cm⁻¹ at 660 nm. The relative standard deviation was 1.2% under nine determinations for 16 ng ml⁻¹ Mo(VI). The present method had been applied to the determination of trace molybdenum in tungsten ores with satisfactory results.     

Orthogonal array design for the optimization of hollow fiber protected liquid-phase microextraction of salicylates from environmental waters

In the present study, a three phase-based hollow fiber protected liquid-phase microextraction (HF-LPME) method combined with high-performance liquid chromatography (HPLC) for the determination of salicylates in environmental waters was developed. The HF-LPME procedure was optimized by an L₁₆(4⁵) orthogonal array experimental design (OAD) with five factors at four levels. Under the optimal extraction condition (pHs of donor and receiving phases of 3.0 and 6.2, respectively, extraction time of 45 min, stirring speed of 1000 rpm, and salt addition of 20% (w/v)), salicylates could be determined in a linear range from 0.025 to 1.0 μg mL⁻¹ with a good correlation (r² > 0.9930). The limits of detection (LODs) ranged between 0.6 ng mL⁻¹ and 1.2 ng mL⁻¹ for the target analytes. The relative standard deviations (RSDs) of intra-day and inter-day were in the range of 0.64–14.58% and 0.16–15.45%, respectively. This procedure afforded a convenient, sensitive, accurate and cost-saving operation with high extraction efficiency for the model analytes. The method was applied satisfactorily to the determination of salicylates in two environmental waters.     

Fluorimetric properties of a 2-hydroxypropyl-β-cyclodextrin: 9-methyl-benzo[a]phenothiazine inclusion complex in aqueous media. Analytical usefulness

The formation of an inclusion complex between 9-methyl-12H-benzo[a]phenothiazine (MeBPHT) and 2-hydroxypropyl-β-cyclodextrin (HP-β-CD) was investigated in aqueous medium. A 12-fold fluorescence emission intensity enhancement was found for the complexed relative to the free analyte. MeBPHT forms a 1:1 stoichiometry complex with HP-β-CD. A formation constant of 460 (±100) M⁻¹ was calculated using the Benesi-Hildebrand method and fluorimetric data. The limit of detection was 7 ng ml⁻¹ for MeBPHT in the presence of HP-β-CD instead of 60 ng ml⁻¹ in the absence of HP-β-CD.     

Simultaneous determination of cobalt and chromium by ion chromatography with chemiluminescence detection and its application to glass analysis

A method is described for the simultaneous determination of very low levels of Co and Cr by high performance ion chromatography coupled with a chemiluminescence detection system. 0.1M K₂SO₄ solutions, adjusted to pH 3.0, were used as eluent to separate Co(II) and Cr(III) between them and from interferents. The detection system was the chemiluminescence of luminol/ H₂O₂ in alkaline medium catalyzed by such transition metals. Using a matrix solution analogous to soda-lime silica glass (dissolved in acids) calibration graphs were linear up to 0.5 ng ml^–1 for cobalt and up to 250 ng ml^–1 for chromium. The corresponding calculated detection limits (3 s) in such matrix were 0.05 ng ml^–1 and 15 ng ml^–1 for Co and Cr, respectively. The relative standard deviations were 1.4% at 0.5 ng ml^–1 Co level and 2.8% at the 200 ng ml^–1 Cr level. No interferences were observed from the more common metals, particularly those present in glass samples. The ion chromatography/ chemiluminescent method proposed has been successfully applied to the analysis of Co and Cr in glasses.     

Determination of arsenic and antimony in milk by hydride generation atomic fluorescence spectrometry

A highly sensitive procedure has been developed for total arsenic and antimony determination in milk samples by hydride generation atomic fluorescence spectrometry after microwave-assisted sample digestion. The discrete introduction of 2 ml of digested sample in the automated continuous flow hydride generation system allows us to reduce drastically the sample and HCl consume and to determine several elements from a same sample digestion. The method provides detection limits of 0.006 and 0.003 ng ml⁻¹, a sensitivity of 2390 and 2840 fluorescence units per ng ml⁻¹ for As and Sb respectively, and average relative standard deviation of 2.3% for As and 4.8% for Sb. The analysis of cow milk samples, obtained from the Spanish market evidenced the presence of As at concentration levels from 3.4 to 11.6 ng g⁻¹ and Sb levels from 3.5 to 11.9 ng g⁻¹, thus in a proportion near to 1:1, which is in contrast with the 10:1 natural ratio between As and Sb and could evidence the effect of the introduction of new alloys and polymer materials in the industrial process of milk. The method was validated by the comparison of data found for commercial samples by using the proposed procedure and reference methods based on dry-ashing and AFS, and microwave-assisted digestion and inductively coupled plasma mass spectrometry determination.