Y-Mn-O负载的Ni基催化剂用于乙酸自热重整产氢

为了有效地从生物质衍生的乙酸中获得高氢气产率,通过水热法合成了一系列的NiMnY催化剂并用于乙酸自热重整（ATR）过程中,并采用X射线衍射（XRD）、N₂吸附-脱附测试、H₂程序升温还原（H₂-TPR）探究催化剂中的内在联系。在Ni_0.39Mn_0.61YO_3.11±δ催化剂中,经焙烧后形成了类钙钛矿型（Ni,Mn）YO₃物相;经氢气还原后,转化为含有MnO、Y₂O₃和高分散Ni纳米粒子的热稳定的Ni-Mn-Y-O物种。Ni_0.39Mn_0.61YO_3.11±δ具有高效稳定的产氢催化性能,乙酸转化率高达100%,氢气产率达到2.68 mol_H2·mol_HAc^-1。     

负载Ni催化剂用于乙二醇蒸汽重整制氢催化性能研究

采用等体积浸渍法和共沉淀法制备了Ni催化剂,在固定床反应器上考察了Ni负载量、焙烧温度、反应温度等因素对乙二醇低温重整制氢反应活性和选择性的影响。应用X射线衍射、氮物理吸附、H₂程序升温还原等技术对负载型Ni催化剂进行了表征。结果表明,共沉淀法制备的Ni/CeO₂催化剂具有较小的NiO颗粒与CeO₂载体颗粒粒径,催化活性较高。添加少量氧化钴到Ni/CeO₂催化剂中可使H₂收率达72.6%,EG转化率达93.1%。在CeO₂中添加Al₂O₃能提高负载Ni催化剂的活性,乙二醇转化率达94.0%,H₂收率达67.0%;但添加SiO₂则使其活性明显变差。     

碳纳米管负载镍基催化剂对甘油水蒸气重整的性能研究

以硝酸盐为前驱体，CNTs为载体，采用简单浸渍法制备了一系列不同NiO含量的催化剂3Ni-CNTs、 5Ni-CNTs、 10Ni-CNTs和15Ni-CNTs（NiO含量分别为3.0%、 5.0%、 10.0%和15.0%），通过X-射线衍射（XRD）、氢气程序升温还原（H₂TPR）、氢气程序升温脱附（H₂TPD）、 X-射线光电子能谱（XPS）和透射电镜（TEM）对其物理化学性质进行了分析，并考察其对甘油水蒸气重整反应的影响。结果表明：15Ni-CNTs的催化性能最好，在375 ℃条件下，甘油转化率和氢气选择性分别为100%和72.9%。     

Ni/TPC催化剂的制备、表征及在秸秆热解燃气重整中的应用

以废弃汽车外轮胎热解后的副产物轮胎热解焦（Tyre pyrolysis char,TPC）为原料,利用均匀沉淀法制备以轮胎焦为载体的负载型Ni/TPC催化剂,采用EDX、SEM、XRD、TG、BET手段对催化剂进行了表征与分析,同时使用管式炉测试了Ni/TPC催化剂在秸秆热解燃气重整中的催化性能,并考察了热解温度、保温时间、镍负载量及催化时间对秸秆热解燃气重整效果的影响。研究结果表明,TPC富含焦和金属,Ni/TPC催化剂分散均匀,热稳定性好,比表面积为62 m²/g。催化剂活性测试显示,Ni/TPC催化剂用于作物秸秆热解燃气重整具有很强的催化活性,可显著提高燃气中可燃气体含量;热解温度在750℃、保温时间10 min、30%的Ni负载量时Ni/TPC催化剂的催化效率最高,连续使用850 min后,燃气中的H₂含量仍相对提高到50%以上,长时间使用后活性结构由Ni₃ZnC_0.7转变成FeNi₃,催化活性依然较强且趋于稳定,TPC可以作为良好的新型镍基催化剂载体。     

乙酸自热重整制氢用类水滑石衍生Zn-Ni-Al-Fe-O催化剂研究

采用共沉淀法制备了Zn_(2.4)Ni_(0.6)Al_xFe_(1-x)O_(4.5±δ)(x=1/0.5/0)系列类水滑石型镍基催化剂,用于乙酸自热重整制氢,并利用XRD、H_2-TPR、BET、XPS等表征手段对催化剂进行了表征。结果表明,Zn_(2.4)Ni_(0.6)Al_(0.5)Fe_(0.5)O_(4.5±δ)催化剂在乙酸自热重整中乙酸转化率维持在100%,氢气产率为2.39 mol-H_2/mol-HAc。Zn-Al水滑石前驱体经焙烧后形成了ZnO为骨架的复合氧化物,铁的适量添加增大了催化剂的比表面积,经还原后形成Fe NiZn合金,Fe以及Zn的给电子作用提高了Ni的抗氧化能力,催化剂的抗氧化烧结和抗积炭能力得到提高。     

钙钛矿型氧化物负载Ni催化剂上甲烷二氧化碳重整反应研究

采用浸渍法制备了一系列MTiO₃(M=Mg、Ca、Sr、Ba)钙钛矿型氧化物负载的Ni催化剂(Ni的负载量为5%,质量分数),通过XRD、氮吸附、H₂-TPR、CO₂-TPD、XPS和TG等技术对催化剂进行了表征,对其甲烷二氧化碳重整反应的催化性能进行了研究。结果表明,M为不同碱土金属时,催化剂上金属载体相互作用、活性组分的表面原子浓度以及催化剂晶格氧的流动性都发生了变化。Ni/CaTiO₃催化剂上金属载体相互作用较强,还原出的活性组分Ni的含量较多,晶格氧流动性较高,因而具有较好的催化性能。SrTiO₃载体颗粒粒径较大,Ni/SrTiO₃催化剂上Ni的分散度不高,金属载体的相互作用较弱,表面Ni原子相对含量较低,晶格氧的流动性较差,其甲烷二氧化碳重整反应活性也最低。     

流化床中高分散镍基催化剂上甲烷的自热重整和部分氧化

Highly dispersed Ni catalysts on spherical SiO2 were prepared by simple impregnation of Ni（acac）2, [Ni-（NH3）6-n（H2O）n]^2＋, [Ni（en）3]^2＋ and [Ni（EDTA）]^2-. Pulse adsorption of H2 and TEM analysis results confirmed that Ni was dispersed very well on the surface of SiO2 even after calcination （4 h） and reduction （1 h） at high temperature of 800 ℃. These highly dispersed and uniquely sized Ni crystallites were more stable and more reactive for both autothermal reforming and partial oxidation of methane in fluidized reactor.     

Pd基催化剂在分解甲酸析氢中的研究进展

甲酸是最简单的羧酸,无色、低毒,在室温下便于运输和储存。最近,甲酸作为一种最有前景的储氢材料,在室温下采用异相催化剂分解甲酸制氢气引起了科研工作者的广泛关注。和其他催化剂相比,Pd基催化剂在温和条件下催化甲酸分解制备氢气方面表现出优良的性能,是一种非常理想的非均相催化剂。本文介绍了多种Pd基催化剂的性能特点、制备方法和其在催化甲酸分解制备氢气领域的研究进展,并对其未来研究发展方向进行展望。     

Ni基催化剂催化燃油重整耦合选择性催化还原NOx反应

分别以La₂O₂CO₃, CeO₂, ZrO₂和Al₂O₃为载体, 采用浸渍法制备了Ni基重整催化剂, 并以正十二烷模拟车载燃油进行催化重整反应以同时制备小分子碳氢化合物(HCs)和H₂, 考察了其在4wt%Ag/Al₂O₃上选择性催化还原(HC-SCR)氮氧化物(NO_x)的性能. 采用N₂吸附-脱附、X射线粉末衍射、H₂程序升温还原和热重等手段对Ni基催化剂进行了表征. 结果表明, 随着重整催化剂氧化还原性能增强, 产物中H₂浓度增加, 可参与SCR反应的HCs含量减少, 从而导致重整-SCR耦合体系上NO_x净化活性温度窗口向低温移动, NO_x最高转化率降低. Ni/ZrO₂+Ag/Al₂O₃耦合体系中H₂/HCs符合SCR反应所需的最优比例, 在柴油车典型排气温度范围内表现出良好的NO_x净化能力. 同时, 在Ni/ZrO₂+Ag/Al₂O₃耦合体系上考察了其燃油重整-SCR的活性稳定性. 结果显示, 重整催化剂的耐久性有待进一步提高.     

制备条件对用于甘油蒸汽重整反应Ni基催化剂性能的影响

研究了制备参数对用于甘油蒸汽重整反应的Ni基催化剂性能的影响。采用过量浸渍法、等体积浸渍法和改进的平衡沉积过滤(EDF)法制备了一系列Al2O3负载的8 wt%Ni催化剂,运用X射线衍射(XRD)、电感耦合等离子体光谱仪、N2吸附-脱附、扫描电镜(SEM)、透射电镜和H2程序升温还原(TPR)表征了催化剂的表面和体相性质;采用CHN分析仪和SEM表征了使用后催化剂以测定其表面沉积的碳及其形貌。结果表明,制备方法对所制催化剂的织构、结构和表面性质影响很大,导致氧化铝表面Ni物种的分散和种类的不同。即使XRD和TPR结果证实形成了铝酸镍晶相,但Ni/Al-edf催化剂中β峰的贡献大于其它两个催化剂的,表明在这种情况下铝酸镍更容易还原。在550 oC以上CO2选择性增加和CO选择性不变,表明Ni/Al-wet和Ni/Al-edf催化剂可成功催化水汽变换反应。另外,650oC时Ni/Al-edf催化剂上甘油生成气相产物的转化率、氢气产率以及烯丙醇、乙醛和乙酸选择性最高,且它在所有催化剂中的积炭量也最低。将催化剂结构性质、分散度和还原性与其催化性能相关联,发现EDF法制得的催化剂比表面积和活性相分散度更高,更易被还原,因而其活性和生成H2的选择性更高,也更抗积碳。     

Support Modification of Supported Nickel Catalysts for Hydrogen Production by Auto-thermal Reforming of Ethanol

Recent progress on support modification of supported nickel catalysts for hydrogen production by auto-thermal reforming of ethanol was reported in this review. Nickel catalysts supported on various materials, including metal oxides and metal oxide-stabilized mesoporous zirconias, were prepared by an incipient wetness impregnation method for use in hydrogen production by auto-thermal reforming of ethanol. Various experimental measurements such as NH₃-TPD (temperature-programmed desorption) and TPR (temperature-programmed reduction) were carried out to elucidate the different catalytic performance of supported nickel catalysts. It was revealed that acid property of supporting materials served as one of the important factors determining the catalytic performance. Hydrogen yield over nickel catalysts supported on metal oxides showed a volcano-shaped curve with respect to acidity of the supports. Among the catalysts tested, Ni/ZrO₂ catalyst with an intermediate acidity exhibited a superior catalytic performance. It was also observed that reducibility of nickel catalysts supported on metal oxide-stabilized mesoporous zirconias played a key role in determining the catalytic performance in the auto-thermal reforming of ethanol for hydrogen production. Hydrogen yield over nickel catalysts supported on metal oxide-stabilized zirconias increased with increasing reducibility of the catalysts (with decreasing TPR peak temperature of the catalysts).     

One‐Step Synthesis of Self‐Supported Nickel Phosphide Nanosheet Array Cathodes for Efficient Electrocatalytic Hydrogen Generation

Nickel phosphide is an emerging low‐cost, earth‐abundant catalyst that can efficiently reduce water to generate hydrogen. However, the synthesis of nickel phosphide catalysts usually involves multiple steps and is laborious. Herein, a convenient and straightforward approach to the synthesis of a three‐dimensional (3D) self‐supported biphasic Ni₅P₄‐Ni₂P nanosheet (NS) array cathode is presented, which is obtained by direct phosphorization of commercially available nickel foam using phosphorus vapor. The synthesized 3D Ni₅P₄‐Ni₂P‐NS array cathode exhibits outstanding electrocatalytic activity and long‐term durability toward the hydrogen evolution reaction (HER) in acidic medium. The fabrication procedure reported here is scalable, showing substantial promise for use in water electrolysis. More importantly, the approach can be readily extended to synthesize other self‐supported transition metal phosphide HER cathodes.     

Oxidative Conversion of Glucose to Formic Acid as a Renewable Hydrogen Source Using an Abundant Solid Base Catalyst

Formic acid is one of the most desirable liquid hydrogen carriers. The selective production of formic acid from monosaccharides in water under mild reaction conditions using solid catalysts was investigated. Calcium oxide, an abundant solid base catalyst available from seashell or limestone by thermal decomposition, was found to be the most active of the simple oxides tested, with formic acid yields of 50 % and 66 % from glucose and xylose, respectively, in 1.4 % H₂O₂ aqueous solution at 343 K for 30 min. The main reaction pathway is a sequential formation of formic acid from glucose by C−C bond cleavage involving aldehyde groups in the acyclic form. The reaction also involves base-catalyzed aldose-ketose isomerization and retroaldol reaction, resulting in the formation of fructose and trioses including glyceraldehyde and dihydroxyacetone. These intermediates were further decomposed into formic acid or glycolic acid. The catalytic activity remained unchanged for further reuse by a simple post-calcination.     

钙钛矿型甲醇水蒸气重整制氢催化材料的研究

采用溶胶凝胶法合成了钙钛矿复合氧化物,负载氧化铜后得钙钛矿负载型催化材料,通过XRD(X射线衍射分析)、BET(比表面积测试)、H2-TPR(程序升温还原分析)、XPS(X射线光电子能谱)等手段对催化材料进行了表征,考察了不同种类钙钛矿负载纳米铜催化材料的结构、性质对甲醇水蒸气重整制氢性能的影响.结果显示,钙钛矿负载纳...     

Paper-like Microfibrous Nickel Catalyst for Hydrogen Production via NH3 Decomposition in Fuel Cell Applications

Recently, miniature H2 generator to power fuel cells for portable/micro electronic devices and passenger propulsion has been the focus of intense research activities1-3. One of the strategies is to find simple CO-free H2 production with novel microreactor…     

甲醇自热重整制氢用Cu-ZnO/Al2O3催化剂的研究

 研究了负载于堇青石蜂窝陶瓷载体上的Cu-ZnO/Al2O3催化剂对甲醇自热重整制氢反应的催化性能,考察了铜负载量和反应条件对催化剂活性和反应速率的影响,采用XRD和H2-TPR技术对催化剂的分散状态和还原进行了表征. 结果表明,铜负载量较低时铜处于较均匀的分散状态,容易被还原,γ-Al2O3的引入促进了铜的还原. 还原后的低铜负载量的样品上,在空速为4000～12000 h-1和氧/醇摩尔比为0.3的条件下,甲醇的转化率接近100%,H2的生成率和CO2的选择性较高. 证实了还原的铜为反应的活性位.     

功能化氮化碳对Pd基甲酸分解制氢催化剂性能的促进作用

负载型Pd基催化剂是最有效的甲酸分解(FAD)制氢催化剂之一,其中氮化碳载体的N含量较高,但是通常一步热解法制备的氮化碳为块状,难以有效分散表面金属纳米粒子(NPs)。 本文通过将尿素前驱体在溶剂化作用后热解得到功能化氮化碳,以此为载体,利用阴离子交换和硼氢化钠直接还原法制备了功能化氮化碳负载的Pd基催化剂(Pd/C₃N₄-F)。 通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线光电子能谱(XPS)对材料结构进行表征,并通过气体质量流量计测试了催化剂的性能。 Pd/C₃N₄-F具有优异的催化FAD制氢性能,30 ℃下的初始TOF(总转换频率)值和质量比活性分别为1824 h^-1和17.14 mol_H2/(g_Pd·h)。 对产物的气相色谱分析结果也表明没有副产物CO生成,表明催化剂具有优异的选择性。 并且随着温度的升高(30～40 ℃),催化剂性能逐渐提高。     

Selective Hydrogen Production from Methanol with a Defined Iron Pincer Catalyst under Mild Conditions

Molecularly well‐defined iron pincer complexes promote the aqueous‐phase reforming of methanol to carbon dioxide and hydrogen, which is of interest in the context of a methanol and hydrogen economy. For the first time, the use of earth‐abundant iron complexes under mild conditions for efficient hydrogen generation from alcohols is demonstrated.