BaHfO_3∶Ce粉体活化能对烧结透光性影响

用正、反向共沉淀法制备了BaHfO3∶Ce粒子;用XRD、TG-DTA、SEM等测试手段对样品的物相、形貌及发光性能进行了表征;在不同升温速率条件下研究了粒子合成动力学。结果表明:由正向和反向沉淀法得到的前驱体物相变化分3个阶段,用Doyle-Ozawa和Kissinger法分别计算了各阶段的表观活化能,其平均值分别为83.41、61.70、262.11 kJ·mol-1和81.70、42.86、253.44 kJ·mol-1,计算正反向沉淀法样品的晶粒生长活化能分别为27.36 kJ·mol-1和23.07 kJ·mol-1;反向法的样品分别在530nm波长下的激发光谱和399 nm波长的发射光谱的相对发光强度优于正向法,在2 073 K真空烧结保温3 h获得具有一定透光性的BaHfO3∶Ce透明陶瓷。     

BaHfO3：Ce粉体活化能对烧结透光性影响

用正、反向共沉淀法制备了BaHfO₃：Ce粒子;用XRD、TG-DTA、SEM等测试手段对样品的物相、形貌及发光性能进行了表征;在不同升温速率条件下研究了粒子合成动力学。结果表明：由正向和反向沉淀法得到的前驱体物相变化分3个阶段,用Doyle-Ozawa和Kissinger法分别计算了各阶段的表观活化能,其平均值分别为83.41、61.70、262.11kJ·mol^-1和81.70、42.86、253.44kJ·mol^-1,计算正反向沉淀法样品的晶粒生长活化能分别为27.36kJ·mol^-1和23.07kJ·mol^-1;反向法的样品分别在530nm波长下的激发光谱和399nm波长的发射光谱的相对发光强度优于正向法,在2073K真空烧结保温3h获得具有一定透光性的BaHfO₃：Ce透明陶瓷。     

正、反向共沉淀法对Pr_2Zr_2O_7纳米粒子表观活化能的影响

以氨水作为沉淀剂,采用正、反向共沉淀法制备Pr2Zr2O7纳米粒子。利用XRD、SEM、TEM、TG-DTA等测试手段表征了样品物相及形貌;研究其制备过程中合成动力学和晶粒生长动力学,采用Doyle-Ozawa法和Kissinger法分别计算正、反向沉淀粒子在主要反应阶段的表观活化能。结果表明:反向沉淀的滴定速率为2 mL·min-1、母盐溶液初始浓度0.05 mol·L-1、反应体系温度273 K、pH值11、煅烧温度为1 173 K,保温2 h的条件下获得的样品形貌近球形、无团聚现象、一次粒径约60 nm。Pr2Zr2O7前驱体的分解过程分为3个阶段,正、反向粒子各阶段平均表观活化能分别为:71.2、97.8、183.2 kJ·mol-1和45.37、84.34、152.16kJ·mol-1;晶粒生长活化能分别为19.02和11.95 kJ·mol-1,后者比前者的晶粒生长活化能降低了7.07 kJ·mol-1;反向共沉淀制备工艺优于正向共沉淀法。     

正、反向共沉淀法对Pr2Zr2O7纳米粒子表观活化能的影响

以氨水作为沉淀剂,采用正、反向共沉淀法制备Pr₂Zr₂O₇纳米粒子。利用XRD、SEM、TEM、TG-DTA等测试手段表征了样品物相及形貌;研究其制备过程中合成动力学和晶粒生长动力学,采用Doyle-Ozawa法和Kissinger法分别计算正、反向沉淀粒子在主要反应阶段的表观活化能。结果表明：反向沉淀的滴定速率为2mL·min^-1、母盐溶液初始浓度0.05mol·L^-1、反应体系温度273K、pH值11、煅烧温度为1173K,保温2h的条件下获得的样品形貌近球形、无团聚现象、一次粒径约60nm。Pr₂Zr₂O₇前驱体的分解过程分为3个阶段,正、反向粒子各阶段平均表观活化能分别为：71.2、197.8、183.2kJ·mol^-1和45.37、84.34、152.16kJ·mol^-1;晶粒生长活化能分别为19.02和11.95kJ·mol^-1,后者比前者的晶粒生长活化能降低了7.07kJ·mol^-1;反向共沉淀制备工艺优于正向共沉淀法。     

LiFePO4锂嵌脱动力学过程研究

采用固相法和微乳液法制备LiFePO4正极材料,制备样品分别用XRD和SEM进行表征,通过交流阻抗和充放电测试电化学性能.结果显示:微乳液法制备样品平均粒径约0.15μm,在2.5-4.0V(vs.Li/Li )范围内、15 mA·g-1电流密度下放电,首次放电容量达到163 mAh·g-1,该样品的表观Li 扩散活化能和表观电荷转移活化能计算值分别为4.95、21.4 kJ·mol-1.制备粒度小的活性物质颗粒有利于减小Li 离子脱嵌动力学限制,提高LiFePO4材料的电化学性能.     

BaCe1-xEuxO3-δ解质的Raman谱与TG-DTA研究

合成了初始摩尔比为Ba/(Ce+Zu)=1.0和1.1的钙钛矿型氧化物BaCe1-xEuxO3-δ(x=0.05,0.10,0.15,0.20).XRD分析表明,过量Ba的样品Ba/(Ce+Eu)=1.1已成钙钛矿单相,样品Ba/(Ce+Eu)=1.0有微量CeO2相存在.Raman谱分析表明,微量CeO2相的产生是由于高温烧结时引起一定量BaO的蒸发引起的;样品Ba/(Ce+Eu)=1.1中过量的Ba对高温烧结时BaO的蒸发起到了补偿作用.热重(TGA)和差热分析(DTA)显示,样品长期放置在空气中,会与空气中的CO2发生一定的反应.     

固溶体MAX相(Ti0.5V0.5)3AlC2的制备及其对MgH2储氢性能的催化影响

通过无压烧结法制备了固溶体MAX相(Ti_(0.5)V_(0.5))_3AlC_2,研究了其添加对MgH_2储氢性能的影响。结果发现,固溶体MAX相(Ti_(0.5)V_(0.5))_3AlC_2中的Ti和V元素通过协同作用,呈现出更高的催化活性。添加质量分数10%(Ti_(0.5)V_(0.5))_3AlC_2的MgH_2样品的起始放氢温度为230℃,较原始MgH_2降低了60℃。在275℃下等温放氢,(Ti_(0.5)V_(0.5))_3AlC_2添加样品的放氢速率可达0.35%·min~(-1),是原始MgH_2样品的4倍左右。此外,完全放氢后的MgH_2-10%(Ti_(0.5)V_(0.5))_3AlC_2样品在150℃、5 MPa氢压下,可在60 s内吸收4.7%的氢。计算显示,MgH_2-10%(Ti_(0.5)V_(0.5))_3AlC_2样品的表观活化能为79.6 kJ·mol~(-1),较原始MgH_2(153.8 kJ·mol~(-1))降低了48%,这是MgH_2放氢性能得到改善的主要原因。     

添加C10H10Cl2Ti对6LiBH4-CaH2-3MgH2体系储氢性能的影响

C_(10)H_(10)Cl_2Ti的添加可以有效改善6LiBH_4-CaH_2-3MgH_2样品吸放氢性能,添加的质量分数为5%时具有较好的催化效果。样品的起始和终止放氢温度比原始样品分别降低约30和25℃,可逆储氢量(质量分数)约为8.1%。添加C_(10)H_(10)Cl_2Ti催化剂的样品在360℃下等温放氢速率比原始样品提高了178%。两步放氢反应的表观活化能分别为131.4和138.8 kJ·mol~(-1),相比原始样品降低了约18.6%和15.8%。利用X射线光电子能谱(X-ray photoelectron spectroscopy,XPS)对样品进行分析发现,热分解过程中C_(10)H_(10)Cl_2Ti生成了多价态的Ti化合物,催化了LiBH_4与CaH_2的反应,从而改善了复合体系的储氢性能。     

喷雾热解法制备球形YAG∶Ce~(3+)荧光粉研究

采用喷雾热解法制备了无团聚的球形YAG∶Ce3+荧光粉。考察了前驱体溶液浓度、载气流速、热解温度对实验结果的影响。当溶液浓度从0.05 mol.L-1增加至0.8 mol.L-1时,所制备的前驱体粒子的平均粒径也从0.60增加至1.50μm,前驱体产量随着前驱体溶液的浓度增加呈现先上升后下降的趋势。提高载气流速可以增加前驱体的产量。当热解温度大于800℃时,得到的粒子呈现实心球体。通过比较喷雾热解法与固相煅烧法所制备的荧光粉,喷雾热解法制备的荧光粉具有发光强度高、形貌好、粒径分布窄等优点。     

Ce0.8Sm0.2O1.9的尿素燃烧法合成与性能

采用以尿素为燃料的燃烧合成法制备Ce0.8Sm0.2O1.9(SDC)氧离子导体材料, 对燃烧合成粉体的物相和显微形态进行了表征, 并研究了燃烧法合成SDC的烧结性能以及烧结体的导电性能. 研究结果表明, 采用尿素燃烧法合成SDC具有简便高效和合成粉体烧结活性高的优点. 经过燃烧过程后即可得到立方萤石结构的纯相SDC粉体, 合成粉体的分散性良好, 为50~150 nm的球形颗粒, 具有高的烧结活性, 在1250 ℃的烧结温度下, 陶瓷样品的相对密度可达到95.1%. 在600和800 ℃的测试温度下, 烧结温度为1250 ℃的陶瓷样品的电导率分别达到5.4×10-2和1.0×10-1 Ω-1·cm-1.     

Near infrared study of aqueous rare-earth ethylsulfates

The near infrared spectra of aqueous solutions of the ethylsulfates of La, Nd, Gd, Tb, Er, Yb, Lu, Y, and Na have been determined from about 0.2 mol-dm^–3 to nearly saturation. The extinction coefficients of water have been calculated taking into account the absorption of ethylslfate anions determined in separate experiments. Their values appeared to be nearly the same as that of pure water. The relative contents of free OH groups in 0.5 and 0.7M solutions have been estimated from the absorbances at 1160 nm. They were lower in solutions of the heavy rare-earth ethylsulfates (Tb, Er, Yb, Lu) than in equimolar solutions of the lighter ones (La, Nd), confirming our previous view that secondary hydration of the heavy trivalent rare-earth cations is distinctly stronger than that of the lighter ones. A comparison of the spectra of these aqueous ethylsulfates with those of perchlorates shows that the structure-breaking ability of the C₂H₅SO ₄ ^– ion is much smaller than that of perchlorate anion.     

Microstructures of Some Bi-W-Nb-O Phases

Microstructures of three Bi-W-Nb-O phases have been examined by using high-resolution transmission electron microscopy. Bi₁₇W₂Nb₃O₃₉ and Bi₁₇WNb₃O₃₆ have incommensurate superstructures derived from the defect fluorite-type δ-Bi₂O₃ and can be regarded as intermediate phases between the type II solid solutions in the Bi-Nb-O and Bi-W-O systems. Bi₈W₂Nb₂O₂₃ has a Bi₂WO₆-like subunit cell with a stepped superstructure. Formation mechanisms of various superstructures are discussed.     

Reactivity of Binary Mixtures of La(III) Oxide and Cu(II) Oxalate or Nitrate and Synthesis of La(III) Cuprate

Reactivity of mixtures of La(III) oxide and Cu(II) oxalate/nitrate in hydrated as well as anhydrous state was studied using TG, DTA and XRD. Cu(II) oxide formed in the endothermic decomposition of mixture containing hydrated Cu(II) nitrate and La(III) oxide could not form La₂CuO₄ while Cu(II) oxide formed in the exothermic decomposition of mixture containing hydrated/anhydrous Cu(II) oxalate and La(III) oxide reacts with La(III) oxide and develops the phases CuLaO₃ and La₂CuO₄. The maximum reactivity with respect to the formation of La₂CuO₄phase was observed in mixture containing anhydrous Cu(II) oxalate. This revised version was published online in July 2006 with corrections to the Cover Date.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

电感耦合等离子体光谱法测定铜冶炼烟尘中锌

本实验介绍了电感耦合等离子体光谱法测定铜冶炼烟尘中锌含量的分析方法。针对样品碳,硅含量高的特点,有针对性的研究了样品的消解方法,确定采用盐酸、硝酸、氢氟酸、高氯酸对铜冶炼烟尘样品进行消解。同时进行了干扰试验,确定样品中高含量的铜,铅,砷等对样品测定结果没有影响。并对仪器的工作参数进行了优化。方法检出限为为0.011 mg/L,测定下限为0.019 mg/L,3个样品的相对标准偏差在0.54%~0.92%之间,加标回收率在96%~101.14%之间。该方法样品消解完全,流程短,操作简单,快速,测定准确度高,可以满足铜冶炼烟尘中锌含量的测定。     

α-Fe2O3掺杂对In2O3电导和气敏性能的影响

用化学共沉淀法制备了α Fe2O3掺杂的In2O3纳米晶微粉,研究了α Fe2O3掺杂对In2O3电导和气敏性能的影响. 结果表明, α Fe2O3和In2O3间可形成有限固溶体In2－xFexO3(0≤x≤0.40); Fe3＋对In2O3晶格中In3＋格位的部分取代,大大增强了阴阳离子间的结合力,导致材料中氧空位VO×数骤降、 自由电子的浓度变稀和电导下降. n(Fe3＋):n(In3＋)=5 :5的共沉淀粉于800 ℃下灼烧4 h所得的α Fe2O3掺杂In2O3传感器元件,对45 μmol•L－1 C2H5OH的灵敏度达54.0,为相同浓度干扰气体汽油的8倍多.     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

Li_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3,Na_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3的离子交换研究

研究了在不同温度下的NaNO3和AgNO3水溶液中Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3离子交换行为.实验表明Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3均显示出了高选择性与Na+和Ag+进行离子交换的特征,且对Ag+的选择性高于Na+.升高温度可显著提高Ag/Li和Ag/Na的交换反应速度.     

Reactivity of Zn3V2O8 Towards ZnMoO4 in the Solid State

The reactivity of Zn₃ V₂ O₈ towards ZnMoO₄ was investigated by using DTA and XRD methods. A new compound of the formula Zn_2.5 VMoO₈ was found. It crystallises in an orthorhombic system. The melting temperature was determinated to be 845±5°C. This revised version was published online in August 2006 with corrections to the Cover Date.