Tb~(3+):ZnO/ZnS荧光粉的结构与发光性能

采用溶胶凝胶-沉淀法制备掺杂Tb~(3+)的ZnO/ZnS绿色荧光粉。通过XRD与IR手段对所制备的绿色荧光粉的结构进行分析。XRD测试结果表明,荧光粉主要以ZnO和ZnS形式存在,其中ZnO属于六方相结构(No.74-0534)、 ZnS属于三角晶结构(No.89-2427)。TEM显示荧光粉呈无规则块状,S的含量为1.85%(原子分数)。IR测试结果表明:绿色荧光粉主要含有Zn-S键、 Zn-O键,其相应吸收峰的位置随退火温度的升高而发生变化。利用激发谱图和发射谱图的分析,探讨荧光粉的发光性能及发光机制。荧光粉制备的最佳退火温度为800℃, Tb~(3+)以磁偶极跃迁为主(~5D_4→~7F_5);掺入ZnS可形成新的能带结构且增大复合几率,从而提高了荧光粉的发光性能,即ZnO/ZnS:Tb~(3+)荧光粉的发光性能强于ZnO:Tb~(3+)荧光粉的发光性能。     

ZnO/Eu~(3+)发光材料的高温固相合成及其发光性能

采用高温固相法制备了ZnO/Eu3+红色长余辉发光材料.应用正交试验设计法(每个因素取3个水平,选用L9(34)正交试验表),以初始亮度为指标,研究了煅烧温度、Eu3+质量分数、敏化剂Li+质量分数、煅烧时间等4个因素对发光性能的影响;利用X射线衍射仪对合成的ZnO/Eu3+发光材料进行了物相分析,应用荧光分光光度计测定了样品的激发光谱和发射光谱,应用照射计测定了样品的发光特性.结果表明,当各个因素在水平范围内变化时,所制备的样品均具有ZnO晶格结构;荧光粉的主激发峰位于365 nm和458 nm处,主发射峰位于480 nm、570 nm和600 nm~640 nm,对应于Eu3+的4f和5d间的激发和发射.所确定的最佳合成条件为:煅烧温度850℃,w(Eu3+)=4%,w(Li+)=2.5%,煅烧时间3 h.     

NaY(WO4)2∶Eu3+/Tb3+/Tm3+白色荧光粉的制备与发光性能

采用溶剂热法合成了一种单一相白色荧光粉NaY(WO4)2∶Eu3+,Tb3+,Tm3+。通过X射线衍射(XRD)、扫描电镜(SEM)、X射线能谱(EDS)及荧光光谱(PL)对制备的系列样品的物相、形貌和荧光性质进行了表征。结果表明:在荧光粉NaY(WO4)2∶x%Eu3+,4%Tb3+,1%Tm3+(x=5,10,15,20)中,随着Eu3+掺入量的增加,发光从绿光区进入白光区。同时观察到Tb3+到Eu3+的有效能量传递。     

SrSi2O2N2∶Eu2+荧光粉的制备及性能研究

以SrCO3,Si3N4,Eu2O3为原料,在N2气氛下,采用自还原高温固相法制备了SrSi2O2N2:Eu2+荧光粉。研究了该荧光粉的物相结构、发光性能和晶体形貌,同时对比在不同气氛下合成的荧光粉。结果表明,在N2气氛与N2/H2气氛下分别合成的SrSi2O2N2:Eu2+荧光粉物相结构和光谱特性基本一致。显示出合成了主晶相SrSi2O2N2,但还含有少量未知的中间项。Eu2+浓度的变化不影响激发状态,而发射光谱的波长在Eu2+浓度为1mol%-20mol%之间,从530 nm的绿光红移至550 nm的黄绿光区域。同时,激发光谱覆盖的范围宽,均能有效的被UV或蓝光激发,这意味着该类荧光粉在白光LED方面有可能得到广泛的应用。     

不同方法制备CaMoO4∶0.05Eu3+红色荧光粉的对比研究

分别以高温固相法、溶胶-凝胶法、水热法和共沉淀法合成Eu3+掺杂的CaMoO4红色荧光粉,通过X-射线衍射(XRD)、场发射扫描电镜(FESEM)、傅立叶变换红外光谱(FTIR)、光致荧光光谱(PL)进行表征,考察荧光粉晶相、形貌及发光性能对制备方法的依赖性。实验表明,由于Ca2+的半径(0.099 nm)与Eu3+半径(0.094 7 nm)大小相差不大,Eu3+容易取代Ca2+的位置进入晶格,Eu3+掺杂的CaMoO4在晶体结构上保持白钨矿结构。FESEM结果表明:未经后处理的水热法所得样品为片状、多孔结构;高温固相法所得样品尺寸大、团聚严重;溶胶-凝胶法所得样品分散度好、呈条形结构;共沉淀法所得样品形貌、尺寸比较均一。荧光光谱显示,四种样品发光强度差异很大,共沉淀法制得样品的发光强度为未经后处理的水热法制得样品的6-7倍,该现象主要是由样品形貌及表面缺陷的差异引起的。     

Si-N共掺对CaAl2O4:Eu2+和CaAl2O4:Eu2+,Sm3+荧光粉荧光和余辉性能的优化

采用高温固相反应法制备了不同浓度Si-N共掺的CaAl2O4:Eu2+蓝色荧光粉,发现只需2%(摩尔分数)的Si-N共掺就可以明显提高荧光粉的荧光性能。研究还发现在CaAl2O4:Eu2+,Sm3+中掺入Si-N后,荧光粉的荧光强度和余辉性能都有提高。通过荧光粉的光谱图,发现共掺没有改变荧光粉中发光中心Eu离子的价态,而电子顺磁共振(EPR)谱则表明,Si-N共掺对Eu离子周围的配位环境产生了较大的影响。这说明掺杂的Si-N倾向于取代Eu2+附近的Al-O,并且由于Si-N键相对于Al-O键具有较短的键长,使发光中心周围晶体骨架的刚性得到了增强,从而减少了晶格热震动导致的非辐射跃迁能量损失,提高荧光粉的发光性能。同时,热释光谱表明,掺杂的Si-N会在发光离子周围产生新的缺陷能级,从而提高荧光粉的余辉性能。     

Gd_3Al_5O_(12)∶Eu~(3+)柠檬酸盐硝酸盐燃烧法合成及其发光性能研究

采用柠檬酸盐硝酸盐燃烧法,在较低的温度(900℃)下成功地合成单一晶相Gd3Al5O12∶Eu3+发光粉体,紫外激发荧光光谱分析表明,粉体615 nm和593 nm荧光发射源于Eu3+的5D0-7F2和5D0-7F1跃迁.该方法中各工艺条件(如pH值、柠檬酸/金属离子比、煅烧温度)对Gd3Al5O12∶Eu3+发光性能均有影响,通过试验得出了获得最佳发光性能荧光粉体的工艺参数.     

Lu2O3和Lu2O3:Eu3+单分散球形粉体合成及其荧光性能研究

以Lu(NO3)3和尿素为原料,采用均相沉淀法合成镥盐前驱体,研究Lu3+浓度、尿素/Lu3+摩尔比R对前驱体形貌的影响。结果表明,在反应温度为95℃时,低Lu3+浓度有利于单分散球形粉体的合成,并且适当的调整R值可将单分散球形颗粒尺寸控制在180～270 nm之间。在此基础之上,研究Eu3+掺杂Lu2O3单分散球形荧光粉体的合成,探讨了Eu3+的掺杂量(1%,3%,5%,7%,9%(原子分数))及煅烧温度(600～1200℃)对颗粒形貌及其荧光性能的影响。结果表明,Eu3+的掺杂使所得(Lu,Eu)盐前驱体颗粒尺寸远小于单纯的Lu盐前驱体,且Eu含量对荧光粉的荧光强度有着显著的影响,荧光淬灭浓度为5%。在考察的煅烧温度范围内,荧光粉的荧光强度随煅烧温度的提升而增强。     

白光LED用荧光材料Ba3 Gd( BO3 )3:Eu3+的发光性能研究

用高温固相反应法制备了稀土离子Eu3+ 掺杂的三元稀土硼酸盐Ba3Gd(BO3)3发光材料, 通过X射线衍射 (XRD) 、荧光光谱和扫描电镜 (SEM) 等测试手段对Ba3Gd(BO3)3:Eu3+ 荧光粉的制备条件、发光性能以及形貌进行了研究. XRD结果表明, 在1000 ℃时可得到Ba3Gd(BO3)3 纯相. 扫描电镜照片显示颗粒基本为球形, 粒径约为200～400 nm. 发光光谱测试表明, Ba3Gd(BO3)3:Eu3+荧光粉在近紫外区(UV) (396 nm)和蓝光区(466 nm)可以被有效地激发, 分别用255和396 nm的紫外光激发样品时, 以Eu3+ 的 5D0-7F2 (611和616 nm) 超灵敏跃迁为主要发射峰. 当Eu3+的掺杂浓度为10%(摩尔分数)时, Ba3Gd(BO3)3:Eu3+ 在611和616 nm处的发光强度最大. 因此, 这种荧光粉是一种可能应用在白光LED上的红色荧光材料.     

白光用红色荧光粉Gd2SrAl2O7:Eu3+的合成及发光性能研究

用传统的固态反应法合成了新型红色Eu3+掺杂的Gd2SrAl2O7红色荧光粉。通过添加Li2CO3助熔剂,有效地降低了反应温度,获得了纯Gd2SrAl2O7相。用X射线衍射仪分析确认了产物为Gd2SrAl2O7晶相,并用光谱仪测试了光谱性能,发现当Eu3+掺杂浓度为30%时,荧光粉在623 nm处有最强发光,是Y2O3:Eu3+的两倍。(Gd0.7Eu0.3)2SrAl2O7(x=0.650,y=0.349)色度值与美国国家电视标准委员会标准值(x=0.670,y=0.330)接近。     

Ce3+,Tb3+,Eu3+共掺杂Sr2MgSi2O7体系的白色发光和能量传递机理

通过正交试验,采用高温固相法制备了Sr2-x-y-zMgSi2O7∶xCe3+,yTb3+,zEu3+系列样品.使用X射线衍射仪和荧光光谱仪表征了样品的物相和发光性质,并讨论了Ce3+-Tb3+-Eu3+共掺杂Sr2MgSi2O7体系中的能量传递过程.实验结果表明,在327 nm波长激发下,所合成荧光粉的发射峰主要位于387 nm(蓝紫)、542nm(绿)和611 nm(红)处;分别以387,542和611 nm为监控波长,所得激发光谱显示荧光粉在327 nm处有最好的激发.在327 nm光激发下,系列样品发光进入白光区.最优化的荧光粉为Sr1.91MgSi2O7∶0.01Ce3+,0.05Tb3+,0.03Eu3+,其色坐标为(0.337,0.313),是一种潜在的发光二极管(LED)用白色荧光粉.     

白色荧光粉NaGd（MoO4）2:Dy3+,Eu3+的水热合成及发光性能

采用谷氨酸辅助水热法合成了八面体形NaGd(MoO4)2:Dy3+,Eu3+白色荧光粉.X射线衍射结果表明,合成的样品为四方晶系的NaGd(MoO4)2纯相.扫描电子显微镜照片显示所制备的粒子为八面体形,各边长约为2μm.荧光光谱结果表明,在NaGd(MoO4)2:4%Dy3+,yEu3+(y=0,0.5%,0.6%,0.7%,0.8%,0.9%,1.0%)样品中,随着Eu3+掺入量的增加,Dy3+的发射峰逐渐减弱,而Eu3+的发射峰逐渐增强,说明Dy3+-Eu3+之间存在能量传递.通过色坐标图可知,当Eu3+掺杂量y=0.9%时,荧光粉的色坐标(0.338,0.281)与标准的白光色坐标(0.33,0.33)接近,表明NaGd(MoO4)2:4%Dy3+,0.9%Eu3+是很好的近紫外光激发下的白色荧光粉.     

Eu3+掺杂的LaBO3荧光粉制备及发光性能

采用水热法合成前驱体,后经热处理方式制备不同晶相的LaBO3∶Eu^3+荧光粉。通过X射线衍射(XRD)、电子扫描电镜(SEM)、红外光谱和荧光光谱对样品的结构、形貌和发光性能进行了研究。并研究了硼酸用量、热处理温度及初始溶液pH等对晶相结构和发光性能的影响。XRD研究结果表明:合成样品具有单斜结构、正交结构及单斜和正交两相混合结构。适当的硼酸用量、较高的热处理温度及较高的初始溶液pH值易于获得正交结构的荧光粉。红外光谱显示:pH值和硼酸用量影响前驱体成分,热处理温度影响晶相的转变。SEM结果显示:LaBO3∶Eu^3+荧光粉的晶粒尺寸随着pH值的增加逐渐减小,与XRD计算结果相一致。荧光光谱结果表明:正交结构的LaBO3∶Eu^3+发光粉具有较高的紫外吸收和较为纯正的红色发射强度。     

YBO3:Eu荧光粉的水热法制备及形貌控制

用水热法在低于300℃成功地制备出具有不同形貌的YBO3:Eu3+荧光粉,其反应温度比固相反应了约800℃.研究了初始原料、pH值、反应温度、反应溶剂和催化剂等条件对目的产物形貌及粒度的,得到了具有Vaterite结构、粒度分布均匀的球形荧光粉的最佳合成工艺.在254nm激发下,水热法的球形Y0.95Eu0.05BO3荧光粉最强发射峰位于598nm处,属于Eu3+的5D0→7F1的跃迁,是固相反应所品的1.5倍.这些结果表明,在PDP和荧光灯等显示和照明用荧光粉的制备中水热法具有潜在的应用.     

Morphology control and luminescence properties of BaMgAl10O17:Eu phosphors prepared by spray pyrolysis

Starting from the aqueous solutions of metal nitrates with citric acid and polyethylene glycol (PEG) as additives, BaMgAl₁₀O₁₇:Eu²⁺ (BAM:Eu²⁺) phosphors were prepared by a two-step spray pyrolysis (SP) method. X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence spectra were used to characterize the resulted BAM:Eu²⁺ phosphors. The obtained BAM:Eu²⁺ phosphor particles have spherical shape, submicron size (0.5-3 μm). The effects of process conditions of the spray pyrolysis, such as molecular weight and concentration of PEG, on the morphology and luminescence properties of phosphor particles were investigated. Adequate amount of PEG was necessary for obtaining spherical particles, and the optimum emission intensity could be obtained when the concentration of PEG was 0.03 g/ml in the precursor solution. Moreover, the emission intensity of the phosphors increased with increasing of metal ion concentration in the solution. Compared with the BAM:Eu²⁺ phosphor prepared by citrate-gel method, spherical BAM:Eu²⁺ phosphor particles showed a higher emission intensity.     

MgAl2O4∶Er^3+,Yb^3+荧光粉的制备及其上转换发光性能

以尿素为沉淀剂,采用低温水热法结合煅烧过程制备出MgAl2O4∶Er^3+,Yb^3+上转换荧光粉,并对样品的结构、微观形貌及上转换发光性能予以表征。结果表明,随尿素加入量的增大,产物主形貌由六角片状结构向纳米棒状转变,经1100℃煅烧可得纯相镁铝尖晶石结构,且Er^3+和Yb^3+能有效进入MgAl2O4晶格并占据Mg^2+位置形成均匀固溶体。在980 nm光激发下,MgAl2O4∶1.0%(n/n)Er^3+,x%(n/n)Yb^3+(x=0~8.0)荧光粉表现出在524、545 nm处绿光以及658 nm处的强红光发射,红绿光强度均在5.0%(n/n)Yb^3+掺杂时达到最大,但红绿光强度比却在7.0%(n/n)Yb^3+掺杂时达到最大值5.2,这归因于Er^3+-Er^3+之间交叉弛豫(CR)在红光发射过程中所起的重要作用。通过控制荧光粉中Yb^3+的掺杂量,能初步实现对于黄绿光色度的有效调控。     

Synthesis and spectral characteristics of Sr2Y8(SiO4)6O2: Eu polycrystals

Spectral-luminescent characteristics of Sr₂Y₈(SiO₄)₆O₂: Eu powder crystal phosphor with the apatite structure and high-intensity luminescence of Eu³⁺ ions have been studied. The charge state of europium in the samples has been characterized by means of X-ray L₃-adsorption spectroscopy. It was established that Eu³⁺ forms two types of optical centers. Besides, luminescence of Eu²⁺ions was found. Reduction Eu³⁺→Eu²⁺ was considered, which may be due to vacancy formation in the 4f crystal lattice position and to negative charge transfer by this vacancy to two ions. Thus, in the silicate lattice there exist inhomogeneously distributed oxygen-deficient centers, which are responsible for nonradiative transfer of excitation energy to Eu³⁺ and Eu²⁺ ions. To study electron-vibrational interactions in the crystal phosphor samples, their IR and Raman spectra were examined. In the luminescence spectrum of Eu²⁺, a series of low-intensity bands caused by interaction of the 4f⁶5d state of Eu²⁺ with silicate lattice vibrations was observed.     

A novel red emitting phosphor Ca2SnO4: Eu

A novel red emitting phosphor, Eu³⁺-doped Ca₂SnO₄, was prepared by the solid-state reaction. X-ray powder diffraction (XRD) analysis confirmed the formation of Ca₂SnO₄: Eu³⁺. Field-emission scanning electron-microscopy (FE-SEM) observation indicated a narrow size-distribution of about 500 nm for the particles with spherical shape. Photoluminescence measurements indicated that the phosphor exhibits bright red emission at about 615 nm under UV excitation. The excellent luminescence properties make it possible as a good candidate for plasma display panels (PDP) application. Splitting of the ⁵D₀-⁷F_J transitions of Ca₂SnO₄: Eu³⁺ suggests that the Eu³⁺ ions occupied two nonequivalent sites in the crystallite. The luminescence lifetime measurement showed a bi-exponential decay, providing other evidence for the existence of two different environments for Eu³⁺ ions.     

ZnO/In2O3复合空心球的制备及其光电催化葡萄糖降解性能

通过葡萄糖协助的水热以及随后的退火处理两步法成功制备了系列ZnO/In₂O₃复合空心球. X射线衍射谱(XRD)表明, 经500 ℃退火制得的ZnO/In₂O₃复合空心球中ZnO以非晶态存在, 但是随着退火温度的提高, 其逐渐转变为纤锌矿结构. 场发射扫描电子显微镜(FE-SEM)和透射显微镜(TEM)结果表明, ZnO/In₂O₃复合材料具有空心球结构, 复合纳米颗粒之间结合紧密. 将ZnO/In₂O₃复合空心球组装成薄膜光电极, 研究了其光电催化降解葡萄糖的性能. 结果表明, 700 ℃退火处理的ZnO/In₂O₃复合空心球薄膜电极可产生最高的光致电流密度. 通过光致发光光谱(PL)发现, 与ZnO或In₂O₃空心球相比, ZnO/In₂O₃复合空心球的发光强度猝灭效果明显. 这是由于复合材料中晶界处产生的p-n结电场, 降低了光生电子-空穴对的复合几率, 从而使更多的光生电子可迁移到电极表面.     

电化学溶解钛金属直接水解法制备纳米TiO2

Metallic titanium was electrochemically dissoluted in absolute ethanol in the presence of Et4N•Br(as electro conductive additive),The electrolyte solution was then directly hydrolysized to obtain nanocrystalline TiO2.The powder obtained was calcined at 720℃ for 1 h.FT IR,Raman spectra,XRD and TEM were used to investigate the structure and particle size of the powder.Studies showed that the nanocrystalline TiO2 prepared by this method was of monocline structure with high textural stability and narrow size distribution of 10－20 nm,and its Raman spectra showed a shift of about 25 cm－1.The experiments also showed that the product yield could be improved by controlling the temperature under 50－60℃,selecting R4N•Br as conductive additive and preventing titanium anode from being passivated.The electrochemical dissolution of metal anode may be recommanded as a promising technique for the synthesis of nanomaterials.