碳纳米管传感器方波伏安法检测环境水样中的百草枯

制备了多壁碳纳米管修饰玻碳电极,采用循环伏安法等方法研究了农药百草枯在修饰电极上的电化学特性,建立了一种新的检测百草枯的电化学分析方法。在最佳实验条件下,用方波伏安法检测百草枯,其响应电流与百草枯的浓度在5.38×10-7~2.37×10-4mol/L范围内有很好的线性关系,检出限为5.0×10-7mol/L。用此方法检测了环境水样中的百草枯。     

Rapid quantitative detection of capsaicinoids in serum based on an electrochemical immunosensor with a dual-signal amplification strategy

Journal of Solid State Electrochemistry - In this paper, a dual-signal amplified electrochemical immunosensor for quantitative detection of capsaicinoids in serum was reported, which could be used...     

A molecularly imprinted polymer based on functionalized multiwalled carbon nanotubes for the electrochemical detection of parathion-methyl

A novel composite of vinyl group functionalized multiwalled carbon nanotubes (MWCNTs) molecularly imprinted polymer (MIP) was synthesized and applied as a molecular recognition element to construct an electrochemical sensor for parathion-methyl in this paper. The special molecular recognition properties of parathion-methyl mainly dominated by π-π, p-π interaction and hydrogen bonding formed among functional monomer, template and matrix. A series of electrochemical experiment results proved that the prepared material had good adsorption capacity and fast mass transfer rate to parathion-methyl. The good selectivity of the sensor allowed fine discrimination between parathion and paraoxon, which had similar structures to parathion-methyl. The response of the MIPs was linearly proportional to the concentration of parathion-methyl over the range of 2.0 × 10(-7) to 1.0 × 10(-5) mol L(-1) with a lower detection limit of 6.7 × 10(-8) mol L(-1) (S/N = 3). This sensor was also applied in the detection of parathion-methyl in pear and cucumber with average recoveries of between 94.9% and 106.2% (RSD < 5%) being obtained. The results mentioned above show that the novel electrochemical sensor is an ideal device for the real-time determination of parathion-methyl in real samples.     

Functionalization of single-walled carbon nanotubes for direct and selective electrochemical detection of DNA

We report here a new strategy to graft both redox and DNA probes on carbon nanotubes to make a label-free DNA sensor. Oxidized single-walled carbon nanotubes are first immobilized on a self-assembled monolayer of cysteamine; then the redox probe, a quinone derivative 3-[(2-aminoethyl)sulfanyl-5-hydroxy-1,4-naphthoquinone], is grafted on the free carboxylic groups of the nanotubes. After that, for DNA probe grafting, new carboxylic sites are generated via an aryl diazonium route. After hybridization with a complementary sequence, the conformational changes of DNA could influence the redox kinetics of quinone, leading to a current increase of the redox signal, detected by square wave voltammetry. The system is selective, as it can discriminate a single mismatched sequence from the complementary one.     

Synthesis and electrochemical properties of composites based on carbon nanotubes and polyaniline

composites made of polyaniline and multiwalled carbon nanotubes have been electrochemically synthesized. The modification of multiwalled carbon nanotubes by a salt of phenyldiazonium significantly increases the redox currents of the polyaniline matrix in the composite. As a result of modification, the conformational state of polyaniline macrochains changes, leading to changes in the morphology, structure, and chemical composition of the composite.     

A sensitive DNA electrochemical biosensor based on magnetite with a glassy carbon electrode modified by muti-walled carbon nanotubes in polypyrrole

A novel sensitive electrochemical biosensor based on magnetite nanoparticle for monitoring DNA hybridization by using MWNT-COOH/ppy-modified glassy carbon electrode is described. In this new detection system, mercapatoacetic acid (RSH)-coated magnetite nanoparticles, capped with 5′-(NH₂) oligonucleotide, is used as DNA probe to complex 29-base polynucleotide target (a piece of human porphobilinogen deaminase PBGD promoter from 170 to 142). Target sequence hybridized with the probe results in the decrease of the reduction peak current of daunomycin connected with probe. The response of non-complementary sequence was almost the same as the blank, and the response of three-base mismatched sequence within 29-base polynucleotide was obviously distinguished from complementary sequence, which can easily identify point mutation of DNA. The equation of calibration plot is i_p (μA) = 0.8255 − 0.0847c_{target oligonucleotide} × 10¹³ in the range of 6.9 × 10⁻¹⁴ to 8.6 × 10⁻¹³ mol/L, and correlation coefficient is 0.9974. The detective limit is 2.3 × 10⁻¹⁴ mol/L of target oligonucleotide. This device can be optimized for the detection of complex sequence.     

The evaluation of carbon nanotubes as a sorbent for dicamba herbicide

The potential of carbon nanotubes (CNTs) as a novel sorbent for extraction of dicamba, a highly polar acidic herbicide, from aqueous samples was evaluated. The sorption capacity of CNTs increases remarkably with decreasing sample pH. The solution of ACN and ammonia (80:20 v/v) was found to be the most effective as the eluent for desorption from a 0.2 g CNT cartridge. The method was tested for river water samples with the LOD of 2 microg/L (for 100 mL sample) and compared with C18 bonded silica.     

Determination of beta-carboline alkaloids in foods and beverages by high-performance liquid chromatography with electrochemical detection at a glassy carbon electrode modified with carbon nanotubes

Simple and sensitive methods for the separation and quantification of β-carboline alkaloids in foods and beverages by HPLC with electrochemical detection at carbon nanotubes-modified glassy carbon electrodes (CNTs-GCE) are reported. Electrode modification with multi-wall CNTs produced an improved amperometric response to β-carbolines, in spite of the working medium consisting of methanol:acetonitrile: 0.05 mol L⁻¹ Na₂HPO₄ solution of pH 9.0 (20:20:60). On the contrary to that observed at a bare GCE, a good repeatability of the amperometric measurements carried out at +900 mV versus Ag/AgCl (R.S.D. of 3.2% for i_p, n = 20) was achieved at the CNTs-GCE. Using an Ultrabase C₁₈ column and isocratic elution with the above mentioned mobile phase, a complete resolution of the chromatographic peaks for harmalol, harmaline, norharmane, harmane and harmine, was achieved. Calibration graphs over the 0.25-100 μM range with detection limits ranging between 4 and 19 ng mL⁻¹, were obtained. The HPLC-ED at CNTs-GCE method was applied to the analysis of beer, coffee and cheese samples, spiked with β-carbolines at concentration levels corresponding to those may be found in the respective samples. The steps involved in sample treatment, such as extraction and clean-up, were optimized for each type of sample. Recoveries ranging between 92 and 102% for beer, 92 and 101% for coffee, and 88 and 100% for cheese, at sub-μg mL⁻¹ or g⁻¹ analytes concentration levels were achieved.     

Rapid hydrolysis and electrochemical detection of trace carbofuran at a disposable heated screen-printed carbon electrode

A disposable heated screen-printed carbon electrode (HSPCE) is successfully fabricated. It demonstrates rapid responses to electrical heating and is easily elevated above the water boiling point by a high frequency alternating current. The temperature rise at the HSPCE was found to be strongly dependent on the square of the heating current and the electrode width. Carbofuran (CAF) could be rapidly hydrolyzed to carbofuran phenol at the HSPCE with raised temperature, and then determined at the same electrode at room temperature by differential potential voltammetry (DPV). The factors influencing the detection were examined, including pH, hydrolytic temperature and heating time. Under the optimum conditions, the detection linear range of CAF was from 4.0 x 10(-7) to 4.0 x 10(-4) mol L(-1) and the detection limit was 5.0 x 10(-8) mol L(-1) (S/N = 3). This method was successfully applied to the analysis of CAF residues in real samples (spiked water, soil and vegetables), and satisfactory recoveries were obtained.     

Determination of phenols in water by on-line solid-phase disk extraction and liquid chromatography with electrochemical detection

Poly(styrene-divinylbenzene) (PS-DVB) membrane extraction disks were used as sorbents for the on-line solid phase extraction of 13 phenols (nitro and chlorophenols) in river and tap waters. Determination was performed by liquid chromatography with electrochemical detection (LC-ED). An acetate buffer-acetonitrile-methanol mixture as mobile phase and amperometric detection at +1100 mV were used. High water volumes, up to 250 ml, can be preconcentrated without loss of phenols (recoveries between 80% and 100%) except for the more polar ones. Moreover, detection limits between 0.01 and 0.1 μg l⁻¹ in tap water and between 0.1 and 1.0 μg⁻¹ in river water were obtained. The method has been applied to the analysis of two river water samples.     

A new solid-phase extraction disk based on a sheet of single-walled carbon nanotubes

A new kind of solid-phase extraction disk based on a sheet of single-walled carbon nanotubes (SWCNTs) is developed in this study. The properties of such disks are tested, and different disks showed satisfactory reproducibility. One liter of aqueous solution can pass through the disk within 10–100 min while still allowing good recoveries. Two disks (DD-disk) can be stacked to enrich phthalate esters, bisphenol A (BPA), 4-n-nonylphenol (4-NP), 4-tert-octylphenol (4-OP) and chlorophenols from various volumes of solution. The results show that SWCNT disks have high extraction ability for all analytes. The SWCNT disk can extract polar chlorophenols more efficiently than a C₁₈ disk from water solution. Unlike the activated carbon disk, analytes adsorbed by the new disks can be eluted completely with 8–15 mL of methanol or acetonitrile. Finally, the DD-disk system is used to pretreat 1000-mL real-world water samples spiked with BPA, 4-OP and 4-NP. Detection limits of 7, 25, and 38 ng L⁻¹ for BPA, 4-OP, and 4-NP, respectively, were achieved under optimized conditions. The advantages of this new disk include its strong adsorption ability, its high flow rate and its easy preparation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Multi-walled carbon nanotubes as a solid-phase extraction adsorbent for the determination of chlorophenols in environmental water samples

Multi-walled carbon nanotubes (MWCNs) are used as adsorbent for solid-phase extraction (SPE) of several chlorophenols (CPs). CPs were adsorbed on MWCNs cartridge, then desorbed with pH 10.0 methanol, finally determined by HPLC. Under the optimized conditions, detection limits of 0.08-0.8 ng mL(-1) were obtained. The method had been applied to analyze the five CPs in tap water and river water.     

Formation of carbon nanotubes in water by the electric-arc technique

A simplified arc discharge apparatus was used for growing carbon nanotubes, required only water (solution) in a glass container with no need for vacuum, water-cooled chamber. Carbon nanotubes with highest purity (20%) and highest yield (7 mg/min) were obtained when using salt solution as the medium. Resonance Raman spectrum of multi-walled carbon nanotubes (MWNTs) presented in as-grown materials was measured and RBM peaks originating from very thin core nanotubes were observed. The results show that high-quality MWNTs can be effectively prepared in water-arcing process.     

Rapid analysis of pesticide residues in drinking water samples by dispersive solid‐phase extraction based on multiwalled carbon nanotubes and pulse glow discharge ion source ion mobility spectrometry

An analytical method based on dispersive solid‐phase extraction with a multiwalled carbon nanotubes sorbent coupled with positive pulse glow discharge ion mobility spectrometry was developed for analysis of 30 pesticide residues in drinking water samples. Reduced ion mobilities and the mass–mobility correlation of 30 pesticides were measured. The pesticides were divided into five groups to verify the separation capability of pulse glow discharge in mobility spectrometry. The extraction conditions such as desorption solvent, ionic strength, conditions of adsorption and desorption, the amounts of multiwalled carbon nanotubes, and solution pH were optimized. The enrichment factors of pesticides were 5.4‐ to 48.7‐fold (theoretical enrichment factor was 50‐fold). The detection limits of pesticides were 0.01～0.77 μg/kg. The linear range was 0.005–0.2 mg/L for pesticide standard solutions, with determination coefficients from 0.9616 to 0.9999. The method was applied for the analysis of practical and spiked drinking water samples. All results were confirmed by high‐performance liquid chromatography with tandem mass spectrometry. The proposed method was proven to be a commendably rapid screening qualitative and semiquantitative technique for the analysis of pesticide residues in drinking water samples on site.     

Purification of multiwalled carbon nanotubes by annealing and extraction based on the difference in van der Waals potential

The potential energies of van der Waals interactions between two multiwalled carbon nanotubes (MWNTs) as well as two carbon nanoparticles (CNPs) were calculated and compared on the basis of the continuum Lennard-Jones model. The well depth of the potential is 1 order of magnitude higher for MWNTs than for CNPs, indicating that MWNTs and CNPs can be separated from each other through polymer-induced steric stabilization. On the basis of this prediction, a novel method for the purification of MWNTs was proposed. The method involves a high-temperature annealing (2600 degrees C, 1 h) followed by an extraction treatment with a selected dispersing agent. While the annealing process evaporates the metal particles, the extraction treatment removes CNPs. The quality of the nanotubes obtained after purification was examined by laser Raman, thermogravimetric analysis, and electron microscopy observations.     

A label-free cytosensor for the enhanced electrochemical detection of cancer cells using polydopamine-coated carbon nanotubes

An electrochemical, label-free method was developed to detect folate receptor positive tumor cells by specific recognition of a polydopamine-coated carbon nanotubes-folate nanoprobe to cell-surface folate receptors. This strategy offers great promise to extend its application in studying the interaction of ligand and cell-surface receptor.     

Amperometric detection of nitrite based on Dawson-type vanodotungstophosphate and carbon nanotubes

A nitrite sensor based on Dawson vanodotungstophosphates α₂-K₇P₂VW₁₇O₆₂·18H₂O (P₂W₁₇V) and carbon nanotubes (CNTs) was prepared by electrostatic layer-by-layer self-assembly technique. The sensor {PEI/PSS/[PDDA/P₂W₁₇V-CNTs]_n} was characterized by UV–vis spectroscopy, atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray photoelectron spectra (XPS). The electron transfer and sensing ability of this sensor were explored using cyclic voltammetry (CV) and electrochemical impedance spectra (EIS) technology. The results show that the incorporation of CNTs and P₂W₁₇V into the composite film endowed the modified electrode with fast transfer rate and high electrocatalytic activity towards oxidation of nitrite. This nitrite sensor with 10 bilayers has a broad linear range of 5 × 10⁻⁸ to 2.13 × 10⁻³ M, a low detection limit of 0.0367 μM (S N⁻¹ = 3), a high sensitivity of 0.35 mA mM⁻¹ NO₂⁻, an excellent anti-interference property in the presence of other potential interfering species and a good stable. It was successfully employed for determination of nitrite in real towards.