不同质子酸掺杂对银/聚苯胺纳米复合材料结构和导电性的影响

利用紫外光作为辅助条件,在反胶束体系中采用一步双原位法合成了硝酸(HNO3)、对甲基苯磺酸(TSA)和5-磺基水杨酸(SSA)掺杂的银/聚苯胺(Ag/PANI)纳米复合材料.通过对复合材料进行红外光谱(FTIR)、紫外光谱(UV-Vis)、扫描电镜(SEM)、X射线衍射(XRD)和导电性能的测试,研究了不同质子酸对Ag/PANI纳米复合材料结构、形貌和导电性能的影响.测试结果表明,3种酸掺杂制备的Ag/PANI纳米复合材料均为聚苯胺包覆银粒子的核-壳结构.不同的质子酸掺杂会对Ag/PANI纳米复合材料的电性能有重要影响.在3种酸掺杂的复合材料中,TSA掺杂的复合材料的电导率最佳,为215.14 S·cm-1.     

PI/PANI复合材料的制备与表征

以纳米聚苯胺为电磁波的吸收剂,高强度、耐高温的聚酰亚胺为基体设计与制备了高强度、耐热、质轻、薄和吸收宽的新型纳米复合吸波材料.利用微乳液法,以十二烷基苯磺酸(DBSA)为乳化剂和掺杂剂,以过硫酸铵(APS)为氧化剂合成了纳米级聚苯胺(PANI).在此基础上,以PANI的NMP溶液为均苯四甲酸二酐(PMDA)与4,4′-二氨基二苯醚(ODA)的聚合场所,室温下,原位聚合出PANI/聚酰胺酸(PAA)复合材料,再经过亚胺化制备出了PANI/PI复合材料.利用XRD表征了聚合物的结晶形态.红外光谱表征了中间体和聚合物.利用场发射扫描电镜发现PANI/PI复合材料呈现海岛结构,PANI像岛屿一样分散在PI的连续相中,两种材料复合并没有破坏各自的结晶形态.利用数字电桥和自制电极表征了不同含量复合材料的损耗性能,当聚苯胺加到3.4%以上时,复合材料的损耗因数提高了,并且随着频率的增大损耗因数直线增大.     

功能化石墨烯/聚苯胺复合电极材料的制备和电化学性能

利用水合肼还原十八胺(ODA)接枝的氧化石墨烯(GO),得到了十八胺功能化石墨烯(ODA-G),将ODAG与聚苯胺(PANI)通过溶液共混法,制备了功能化石墨烯和聚苯胺纳米复合材料(ODA-G/PANI).采用傅里叶变换红外(FTIR)光谱、X射线衍射(XRD)、热重分析(TGA)、拉曼(Raman)光谱及透射电镜(TEM),对复合材料的结构和形貌进行了表征;利用循环伏安、恒流充放电及交流阻抗谱等,对复合材料的电化学性能进行了测试.结果显示,少量ODA-G的引入为PANI的电化学氧化还原反应提供了更多的电子通道和活性位置,有利于提高PANI的赝电容.在电流密度1.0 A·g-1下,2%(w)ODA-G/PANI的比电容达到787 F·g-1,而相应的PANI仅有426 F·g-1.此外,ODA-G/PANI的循环稳定性也远高于纯PANI.     

不同形貌ZnO@PANI纳米复合材料的制备及光催化性质

采用直接沉淀法和水热合成法制备出形貌和尺寸比较均一的颗粒状、棒状和球形花状的纳米ZnO。使用硅烷偶联剂KH-42(苯胺甲基三乙氧基硅烷,C6H5-NH-CH2-Si(OCH3)3)对所得纳米ZnO进行表面化学修饰,修饰后的纳米ZnO(m-ZnO),经由皮克林乳液聚合法使苯胺单体在其表面聚合,形成聚苯胺(PANI)包覆的氧化锌纳米复合材料(m-ZnO@PANI),采用XRD、SEM、HRTEM、FTIR、UV-Vis、TG等对样品进行表征;研究了m-ZnO@PANI纳米复合材料对亚甲基蓝(MB)的光催化性能。结果表明,复合材料对可见光也有较强的吸收,在紫外、可见光照射下都有较好的光催化降解效率。其中,棒状ZnO纳米复合材料的光催化降解性能最好,它的紫外-可见光和可见光光催化降解率分别达到98.2%和97.1%,而且复合材料的光催化性能稳定,二次循环的紫外-可见光催化降解率仍达到96.0%。     

有限域聚合法制备碳纳米管-聚苯胺复合材料及其电化学性能

通过有限域聚合法将聚苯胺(PANI)均匀地生长在碳纳米管(CNTs)表面, 得到CNTs-PANI纳米复合材料. 通过透射电子显微镜(TEM)、扫描电子显微镜(SEM)、傅立叶变换红外(FTIR)光谱对样品的形貌及成分进行表征. 将得到的复合材料组装成电化学超级电容器, 进行电化学的循环伏安和恒流充放电测试. 结果显示, 运用此有限域聚合法所制备的复合材料中PANI 可以非常均匀地包裹在CNTs表面, 复合材料的比容量可以达到117.7 F·g-1(有机电解液), 远远高于所用纯碳纳米管(25.0 F·g-1)和纯聚苯胺(65.0 F·g-1)的比容量, 从而表明有限域聚合法是一良好的纳米复合材料的制备方法.     

ZnO-聚苯胺同轴纳米线及其列阵的制备和表征

以阳极氧化铝膜 (AAO)作模板 ,制备聚苯胺 (PANI)纳米管和PANI纳米管列阵 ;同时利用溶胶_凝胶法制备ZnO_PANI同轴纳米线和同轴纳米线列阵 .PANI纳米管和ZnO_PANI同轴纳米线的形貌通过透射电子显微镜表征 .PANI纳米管的外径约 3 0nm ,内径约 1 0nm ;ZnO_PANI同轴纳米线直径约 60nm .实验发现 ,较之ZnO纳米线 ,同轴AAO模板中纳米线列阵的可见光发射谱带兰移 ,强度显著增强 ,这可能和PANI链上的NH基团与表面Zn2 +离子之间的相互作用有关 ,以及由于ZnO纳米微粒在PANI上富集、PANI的光生载流子部分转移给ZnO微粒所致 .实验还发现分散在NaOH溶液中的同轴纳米线 ,其可见光发射谱带比AAO模板中同轴纳米线的谱带兰移更甚     

聚苯胺/碳纳米纤维复合材料的制备及电容性能

采用原位聚合法制备了聚苯胺/碳纳米纤维(PANI/CNF)复合材料,用傅里叶变换红外(FT-IR)光谱、热重分析(TGA)、扫描电镜(SEM)和孔分布及比表面积测定仪研究了复合材料的表面官能团、组成、表面形貌及比表面积,并运用循环伏安(CV)法和计时电位法测试了PANI/CNF布作为电极材料的电化学性能.研究结果表明:PANI/CNF复合材料具有粗糙的毛刺结构,PANI沿碳纳米纤维均匀分布;PANI/CNF电极氧化还原反应的可逆性良好;在100mA·g-1电流密度下,当PANI含量为44.4%(w)时,复合材料比电容量高达587.1F·g-1,比能量为66.1Wh·kg-1,电流密度为800mA·g-1时比功率可达1014.2W·kg-1;在5A·g-1的电流密度下,1000次循环充放电后,复合材料的比电容量衰减28%.PANI/CNF复合材料具有良好的导电性和快速充放电能力,是一种优良的超级电容器电极材料.     

PANI/Ce(OH)3-Pr2O3·3H2O/NanoG复合材料制备与表征

开发了反胶束模板-原位聚合纳米复合法制备聚苯胺(PANI)/Ce(OH)3-Pr2O3·3H2O/石墨纳米薄片(NanoG)纳米复合材料的方法.膨胀石墨在乙醇水溶液中经超声处理制得石墨纳米薄片,以苯胺的氯仿溶液为油相,稀土金属离子Pr3+、Ce3+水溶液为水相,依靠表面活性剂十六烷基三甲基溴化铵(CTAB)自组装形成的反胶束为模板-制备PANI/Ge(OH)3-Pr2O3·3H2O/NanoG复合材料.利用红外光谱(FTIR)、扫描电镜(SEM)、透射电镜(TEM)和 X-射线衍射(XRD)对该复合材料进行了表征和分析,研究了其导电性能和热性能.结果表明,PANI/Ce(OH)3-Pr2O3·3H2O/NanoG复合材料各相分散均匀,稀土纳米粒子在体系中以棒状的形态分布.热重分析表明,该复合材料的热稳定性明显提高;导电性研究说明,石墨纳米薄片的特殊的结构(较大的径厚比)对其在聚合物基体中形成导电网络具有重要作用;PANI/Pr2O3-Ce(OH)3/NanoG纳米复合材料的渗滤阀值低于1.0wt%.     

ZnO-聚苯胺复合膜的制备和性能研究

利用溶胶-凝胶法在Au膜、聚苯胺膜(PANI)和ITO(导电玻璃)基体上制备ZnO纳米微粒膜,初步研究了该微粒膜的形貌,结构和紫外-可见吸收等性质.结果表明,PANI的孔洞结构抑制了ZnO颗粒的团聚,因此,ZnO-PANI复合膜的紫外-可见吸收光谱和荧光光谱相对于ZnO-Au微粒膜有一定程度的蓝移.光电流谱研究同时表明,ZnO-聚苯胺复合膜有望在光电化学方面得到应用.     

PANI/AMTES-TiO2纳米复合材料的制备及其光催化性能

首先用偶联剂苯胺基甲基三乙氧基硅烷(AMTES)对纳米TiO2进行表面修饰(AMTES-TiO2), 然后通过苯胺单体在AMTES-TiO2表面的原位化学氧化接枝聚合, 制备了基于共价键结合的聚苯胺(PANI)/AMTES-TiO2纳米复合光催化材料. 用红外光谱(FTIR), X射线衍射(XRD), 热重分析(TGA), 紫外-可见漫反射光谱(UV-Vis-DRS)和荧光发射光谱(PL)等技术对复合材料进行了表征. 以亚甲基蓝(MB)为目标降解物, 研究了PANI/AMTES-TiO2复合材料在太阳光和紫外光下的光催化性能. 结果表明:聚苯胺敏化拓宽了TiO2的光谱响应范围, 复合材料在紫外和可见光区都有较强的吸收, 提高了光能的利用率和光生载流子的分离效率, 使复合材料表现出较高的光催化活性; 苯胺与AMTES-TiO2的质量比(w)对复合材料的光催化活性有较大影响, 当w为0.025时, 复合材料在两种光源下的催化性能均优于TiO2和AMTES-TiO2.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.