氢化双酚A型环氧树脂的固化动力学

将氢化双酚A与环氧氯丙烷反应合成了氢化双酚A型环氧树脂(HBPA-EP),产物分别用多元胺类或酸酐类固化剂固化,利用差示扫描量热分析(DSC)对固化反应特性进行了研究,得到了相应的固化条件、固化反应活化能和固化反应动力学方程等.结果表明,当分别采用1,3-环己二甲胺、液态聚酰胺、顺式六氢苯酐、甲基六氢苯酐固化HBPA-EP(环氧值为0.45)时,其固化条件分别为100℃、2h,145℃、4h,90℃、2h,120℃、4h,130℃、2h,150℃、4h,140℃、2h和160℃、4h,用这4种固化剂进行固化反应的表观活化能分别为50.62、56.88、74.56 kJ/mol和68.36 kJ/mol,其反应级数分别为0.886、0.901、0.915和0.905.     

FTIR法研究环氧树脂固化反应动力学

用傅里叶红外光谱（ＦＴＩＲ）法研究了双酚Ｓ环氧树脂和甲溴双酚Ａ环氧树脂分别与二胺基二苯砜在恒温条件下的固化反应动力学,得出了各反应的表观活化能。     

Monte Carlo Study of Binary Copolymerizations. 2. The Determination of Reactivity Ratios,Applications

This paper discusses an improved and efficient version of the MEMØRY-7 computer program described in a previous paper. The program, called MEMØRY-7/1, implements a Monte Carlo algorithm to compute reactivity ratios in binary irreversible copolymerizations. For the copolymerization of acrylic acid and methyl acrylate, the computed r₁, r₂ values (r₁ = 1.374, r₂ = 1.038) compare quite well with experimentally determined ones (r₁ = 1.4, r₂ = 1.0; Eldridge and Treloar).     

双酚-S环氧树脂与琥珀酸酐固化反应动力学

用差示扫描量热法（ＤＳＣ）研究了双酚－Ｓ环氧树脂（ＢＰＳＥＲ）与琥珀酸酐固化反应的历程。实验结果表明,固化反应主要分两个阶段,前期由化学动力学控制,服从自催化机理。实验数据利用Ｋａｍａｌ方程处理得到两个速率常数ｋ、、ｋ２及两个反应级数ｍ、ｎ、ｋ１、ｋ２的值随反应温度的升高呈增大的趋势,总反应级数ｍ＋ｎ在２～２．５之间,当转化率达到４０％左右后,由于交联程度增加,分子量迅速增长,分子间扩散较慢,进入     

TBBPAER/DDM的固化反应动力学

用等温差示扫描量热法研究了4，4’-二氨基二苯甲烷固化四溴双酚-A环氧树脂的反应动力学，测定了固化反应热，得出了不同温度下固化反应速率与反应程度、固化反应程度与反应时间的关系曲线．结果表明等温固化反应按自催化反应机理进行，用Kamal方程较好地描述了不同温度下其固化反应的自催化反应过程，并反映出不同温度下扩散作用的差别，其动力学参数k1、k2、m、n由非线性回归法拟合而出，k1、k2对应的反应表现活化能分别为52．2kJ·mol-1和46．5kJ·mol-1。     

The effect of zeolite on the curing of epoxy resin by polyaniline: a kinetic study

Polyaniline sulfate‐zeolite composite was prepared by emulsion polymerization. Epoxy resin was cured using polyaniline‐sulfate salt and various amounts of polyaniline sulfate‐zeolite composite. The kinetics of the cure reaction for an epoxy resin based on the diglycidyl ether of bisphenol A (DGEBA) with polyaniline‐sulfate and polyaniline sulfate‐zeolite composite have been studied using differential scanning calorimetry (DSC) under isothermal and dynamic conditions. Isothermal kinetics analysis was performed using the phenomenological model of Kamal. Dynamic kinetic analysis was performed using Kissinger's method. Copyright © 2002 John Wiley & Sons, Ltd.     

Influence of the Curing Temperature in the Mechanical and Thermal Properties of Nanosilica Filled Epoxy Resin Coating

0.5–3 wt% nanosilica was added to an epoxy resin based on diglycidyl ether of bisphenol A (DGEBA) and cured at 25, 40 or 60 °C using isophoronediamine (IPDA) as hardener. Aggregates of nanosilica were properly dispersed into the DGEBA-IPDA resin and agglomerates formation was avoided. Addition of nanosilica increased the storage modulus E′ and the area and height of the tan δ curve of DGEBA-IPDA resin cured at 25 °C, but no significant differences were found by curing at higher temperature. Gel time measurements and the results obtained by applying the Kamal model to isotherm DSC curing of DGEBA-IPDA-nanosilica revealed that nanosilica catalysed the curing reaction between DGEBA and IPDA, in less extent by increasing the curing temperature.     

氮丙啶交联剂的交联性能及固化动力学研究

合成了一种氯丙啶交联剂，并以丙烯酸树脂乳液为模型化合物对交联剂的交联性能及固化动力学进行了研究。结果表明：在丙烯酸树脂乳液中加入适量的氯丙啶交联剂，可使胶膜的力学性能及耐水碱性，耐溶剂性都得到很大的提高；但交联对玻璃化转变温度的影响较小。用程序升温DSC（差示扫描量热法）方法对固化反应动力学进行了研究，计算出固化反应的活化能。     

环氧树脂/桐油酸酐/蒙脱土纳米复合材料固化动力学

环氧树脂/桐油酸酐/蒙脱土纳米复合材料固化动力学;固化反应;DSC     

双酚A甲醛酚醛环氧树脂与二氨基二苯醚的固化反应及热降解

用傅里叶红外光谱、差示扫描量热仪和热重分析测试技术研究了双酚A甲醛酚醛环氧树脂(bis-ANER)与二氨基二苯醚(DDE)的固化反应及其固化产物的热降解性能。在等温固化反应中环氧基团红外光谱吸收强度随固化时间延长而逐渐减弱,羟基吸收强度逐渐增强,固化反应后期出现羰基红外吸收,其强度随固化时间的延长而增强。用Kissinger法和Ozawa-Flynn-Wall法计算出的bis-ANER/DDE非等温固化反应活化能分别为57.6和61.5kJ/mol。固化产物的热降解首先是醚键的断裂,在N2气和O2气气氛下起始阶段的热降解反应均符合g(α)=[-ln(1-α)]2/3的核增长反应机理,2种气氛下高温阶段的热降解机理不同,O2气在降解过程中产生氧化作用。     

Study of cure kinetics of epoxy/DDS/nanosized (SiO2/TiO2) system by dynamic differential scanning calorimetry

In this study the curing kinetics of epoxy based on the diglycidyl ether of bisphenol A (DGEBA), 4,4′‐diaminodiphenyl sulfone (DDS) as a hardener, and SiO₂/TiO₂ (70:30) as a nanofiller was investigated by nonisothermal differential scanning calorimetry (DSC). The effects of different weight contents of SiO₂/TiO₂ nanoparticles were studied using DSC in Dynamic Mode and the best value of the nanofiller was found to be 5 phr (parts per hundred). Dynamic measurements were used to obtain the total heat of reaction of the epoxy system as well as its activation energy (E_a) based on the isoconversional methods of Kissinger and Ozawa. The process revealed a dependence of the activation energy on conversion (α). The morphology of the cured system was investigated by scanning electron microscopy (SEM). It showed a strong cross‐linking between the resin and hardner and a relatively better dispersion of surface modified filler nanoparticles. Copyright © 2009 John Wiley & Sons, Ltd.     

A Well-Defined Cyclotriphosphazene-Based Epoxy Monomer and Its Application as A Novel Epoxy Resin: Synthesis,Curing Behaviors,and Flame Retardancy

Abstract

A novel cyclotriphosphazene-based epoxy monomer, hexa-[4-(glycidyloxycarbonyl) phenoxy]cyclotriphosphazene (HGCP), was synthesized via a four-step synthetic route, and fully characterized by ¹H, ¹³C, and ³¹P NMR spectroscopy, high-resolution mass spectrometry, and elemental analysis. Thermosetting systems based on HGCP with three curing agents, for example, 4,4′-diaminodiphenylsulfone (DDS), 4,4′-diaminodiphenylmethane (DDM), and dicyandiamide (DICY), were used for making a comparison of their thermal curing behaviors. The curing behaviors were measured by differential scanning calorimetry. Moreover, flame retardancy of HGCP thermosetting systems was estimated by Limiting Oxygen Index (LOI) and Vertical Burning Test (UL-94). The resulting HGCP thermosetting systems exhibited better flame retardancy than the common epoxy resins diglycidyl ether of bisphenol A (DGEBA) and the regular brominated bisphenol A epoxy resin (TBBA) cured by DDS, respectively. When HGCP was cured by DDS, its thermosetting system gave the most char residues, met the UL-94 V-0 classification, and had a limiting oxygen index value greater than 35.     

丁腈羟增韧环氧树脂固化反应

丁腈羟增韧环氧树脂固化反应李绍英＊＊韩孝族＊刘振海张庆余（中国科学院长春应用化学研究所长春１３００２２）关键词丁腈羟，增韧环氧树脂，固化反应动力学，ＤＳＣ１９９６－０５－０４收稿，１９９６－０９－１７修回＊＊现在河北轻化工学院化工设计研究所工作环氧树...     

Avrami法研究环氧树脂/蒙脱土/咪唑纳米复合材料的固化动力学

运用Flory凝胶化理论和Avrami法研究环氧树脂／有机蒙脱土／咪唑插层型纳米复合体系在不同温度及不同有机蒙脱土用量时的固化动力学。实验表明,随固化温度的提高,Avrami速率常数k值增大,凝胶化时间tg缩短,凝胶点后的t1/2降低,固化速率加快,当固化温度低于90℃时,Avrami指数n值为3左右,而固化温度高于90℃时,n值为2左右。有机蒙脱土的加入,使固化速率加快,但并不改变固化反应的机理,Avrami方程可以很好地描述凝胶点后的固化动力学。     

咪唑改性氧化石墨烯对阻燃环氧固化动力学的促进作用

讨论了添加量为1%(Per hundreds of resin)的咪唑改性的氧化石墨烯(GO-IPDI-MZ)对磷质量分数为1.5%的环氧树脂体系(1.5P-D-U-EMI)固化的影响.差示扫描量热法(DSC)研究结果表明,当GO-IPDI-MZ添加量为1%时不会改变1.5P-D-U-EMI的非等温自催化固化反应特征.添加1%GO-IPDI-MZ的磷质量分数为1.5%的环氧树脂(1.5P-D-GOM-1)的固化起始温度(Tonset)和峰顶温度(Tp)均比1.5P-D-U-EMI体系低,而总的固化热(ΔH)比1.5P-D-U-EMI体系高.说明GO-IPDI-MZ添加量为1%时,对环氧体系起到一定的促进固化和共固化作用.等温DSC分析表明,在固化反应后期,体系出现了玻璃化转变现象,在此阶段,含扩散控制因子的Kamal模型预测结果与实验结果吻合较好.GO-IPDI-MZ的加入使固化反应相对均匀地进行,对固化反应会产生促进和共固化作用.     

Miscibility and crystallization behavior of PBT/epoxy blends

The miscibility and the isothermal crystallization kinetics for PBT/Epoxy blends have been studied by using differential scanning calorimetry, and several kinetic analyses have been used to describe the crystallization process. The Avrami exponents n were obtained for PBT/Epoxy blends. An addition of small amount of epoxy resin (3%) leads to an increase in the number of effective nuclei, thus resulting in an increase in crystallization rate and a stronger trend of instantaneous three‐dimensional growth. For isothermal crystallization, crystallization parameter analysis showed that epoxy particles could act as effective nucleating agents, accelerating the crystallization of PBT component in the PBT/Epoxy blends. The Lauritzen–Hoffman equation for DSC isothermal crystallization data revealed that PBT/Epoxy 97/3 had lower nucleation constant K_g than 100/0, 93/7, and 90/10 PBT/Epoxy blends. Analysis of the crystallization data of PBT/Epoxy blends showed that crystallization occurs in regime II. The fold surface free energy, σ_e = 101.7–58.0 × 10^?3 J/m², and work of chain folding, q = 5.79–3.30 kcal/mol, were determined. The equilibrium melting point depressions of PBT/Epoxy blends were observed and the Flory–Huggins interaction parameters were obtained. It indicated that these blends were thermodynamically miscible in the melt. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1320–1330, 2006     

Effect of new nonionic curing agent on curing kinetics and mechanical properties of epoxy resin

The current research work presents a novel nonionic curing agent (AEDA) synthesized by utilizing ethylene glycol diglycidyl ether (EGDE), 3,4-dimethoxyaniline (DI), and triethylenetetramine (TETA). Infrared spectroscopy and nuclear magnetic resonance spectroscopy were used to characterize the structure of AEDA curing agent. Non-isothermal scanning calorimetry was used to determine the activation energy and curing conditions of epoxy resin in the curing process. An impact testing machine, a tensile testing machine and a scanning electron microscope (SEM) were used to analyze the impact strength, tensile strength, bending strength, and micromorphology of the AEDA/E-51 system with different mass ratios. The results show that AEDA is an effective high-temperature curing agent. For the AEDA/E-51 system with the optimal mass ratio of 10:100, the best curing temperature is 92.15°C, and the post-curing temperature is 135.65°C. Furthermore, the apparent activation energy (E_a) of 1670 J/mol, the pre-exponential factor (A) of 3.7 × 10^?4, and the reaction series (n) value of 0.76 are obtained for the AEDA/E-51 system. The impact strength of AEDA/E-51 epoxy resin polymer is 7.82 kJ/m², tensile strength is 14.2 MPa, and bending strength is 18.92 MPa. The micromorphological results of the AEDA/E-51 system are consistent with the results of DSC test and mechanical properties test. Hence, this study provides theoretical support for the practical applications of AEDA as curing agent.     

取代脲促进环氧树脂／双氰胺固化体系反应机理

双氰胺作为环氧树脂的固化剂，由于固化产物具有优良的机械和电性能，广泛应用在汽车、航天及电子等领域中．但由于其固化温度高达180C以上，使应用范围受到很大限制．专利文献曾报道晚衍生物作为环氧树脂／双氰胺固化体系的促进剂，可以使体系的固化温度降低到130～140oC，并且在室温下仍保持一定的潜伏性［‘，’］．在以往的研究中，认为取代脉的促进作用在于其与环氧发生反应生成环状化合物2一心竣烷酮和仲胺，仲胺与环氧基进一步反应生成的叔胺可以催化环氧发生阴离子聚合［’～’］．实验表明，环氧树脂／双氰胺／取代脉体系的固化温…     

环单体的合成,聚合及与环氧树脂的固化反应

合成了新螺环原碳酸酯单体：３，９－二（对甲氧基苄基）－１，５，７，１１－四氧杂螺环［５，５］十一烷。以ＢＦ３·ＯＥｔ２为催化剂，实现了其阳离子聚合。聚合产物的＾１Ｈ ＮＭＲ、＾１３Ｃ ＮＭＲ、ＩＲ及元素分析均表明发生了双开环聚合反应。探讨了其聚合历程。用ＤＳＣ和ＩＲ跟踪环氧树脂及其与螺环单体混合后的固化反应过程，研究了固化剂、反应条件对固化反应的影响。     

螺环单体的合成、聚合及与环氧树脂的固化反应

合成了新螺环原碳酸酯单体：３，９－二（对甲氧基苄基）－１，５，７，１１－四氧杂螺环［５，５］十一烷．以ＢＦ３·ＯＥｔ２为催化剂，实现了其阳离子聚合．聚合产物的１ＨＮＭＲ、１３ＣＮＭＲ、ＩＲ及元素分析均表明发生了双开环聚合反应．探讨了其聚合历程．用ＤＳＣ和ＩＲ跟踪环氧树脂及其与螺环单体混合后的固化反应过程，研究了固化剂、反应条件对固化反应的影响