A simple and rapid pre-confirmation method to distinguish endogenous human haemoglobin from synthetic haemoglobin-based oxygen carriers in doping control

A specific, sensitive and rapid analytical procedure based on capillary electrophoresis with UV/Vis detection at 405 and 415?nm was developed and validated to detect human haemoglobin and haemoglobin-based oxygen carriers (Hemopure?, Oxyglobin? and Polyheme?) in blood samples collected for doping control. The electrophoretic separation, based on capillary dynamic coating, was achieved in less than 10 min. The effects of capillary temperature, injection conditions and initial ramping were investigated. The optimum separation voltage was 25 kV with a capillary temperature of 20 °C, initial ramping of 1?kV/s and an injection pressure of 0.5?psi for 10?s. The removal of haptoglobin using anti-human haptoglobin antibody prior to the analysis was mandatory to increase the specificity of the analysis. Sufficient resolution between endogenous haemoglobin variants and the three haemoglobin-based oxygen carriers here investigated was obtained, thus allowing discrimination between a normal haemolysed sample and a sample in which Oxyglobin?, Hemopure? or Polyheme? is present. Good repeatability of migration times (CV% less than 1), peak resolution and adequate sensitivity (limit of detection: 2.5?mg/mL) was obtained.     

Extremely highly efficient on-line concentration and separation of gold nanoparticles using the reversed electrode polarity stacking mode and surfactant-modified capillary electrophoresis

In this study, gold nanoparticles (Au NPs) were separated using the reversed electrode polarity stacking mode (REPSM) of a capillary electrophoresis (CE) system for on-line enhancement prior to performing surfactant-modified CE separation. Under optimized conditions [running electrolyte buffer, sodium dodecyl sulfate (70 mM) and 3-cyclohexylamino-1-propanesulfonic acid (10 mM) at pH 10.0; applied voltage, 20 kV; operating temperature, 25°C; REPSM strategy for sample on-line concentration; REPSM applied prior to initializing separation], two parameters were varied to further enhance the concentration and separation of the Au NPs: (i) the rate of polarity switching (from -20 to +20 kV) between the REPSM and surfactant-modified CE separation modes and (ii) the length of the capillary column. At a polarity switching rate of 1333 kV min(-1) and a column length of ca. 83.5 cm, the resolution of the separation of a mixture of 5.3- and 40.1-nm Au NPs was greater than 19; in addition, the numbers of theoretical plates for the 5.3- and 40.1-nm-diameter Au NPs were greater than 15,000 and up to 1.15×10(7), respectively-the latter being extremely high. Thus, this CE-based method for separating Au NPs provided high performance in terms of separation resolution and the number of theoretical plates, both of which were improved by greater than fivefold relative to those published previously. Notably, the sensitivity enhancement factors for the 5.3- and 40.1-nm-diameter Au NPs were improved (by ca. 20- and 500-fold, respectively) relative to those obtained using conventional surfactant-modified CE separation.     

Application of experimental design and radial basis function neural network to the separation and determination of active components in traditional Chinese medicines by capillary electrophoresis

Orthogonal design has been used to the optimization of separation and determination of two active components in traditional Chinese medicines by capillary electrophoresis. The concentration of phosphate, applied voltage, organic modifier content and buffer pH were selected as variable parameters. Their different effects on peak resolution were studied by the experimental design method. Optimized separation conditions were obtained and successfully applied to the separation and determination of aconitine and hypaconitine in Aconitum medicinal herbs. Good separation was achieved within 7 min using a buffer system composed of 20 mmol L⁻¹ phosphate and 35% acetonitrile at pH 9.5. The applied voltage was 14 kV and the detection was set at 235 nm. In addition, a radial basis function neural network with a “4-18-1” structure was developed based on the experimental results of orthogonal design and uniform design, and was applied to the prediction of peak resolution of the two active components under the optimum separation conditions given by orthogonal design. The predicted results were in good agreement with the experimental values, indicating that radial basis function neural network is a potential way for the selection of separation conditions in capillary electrophoresis.     

Nonaqueous capillary electrophoresis of dextromethorphan and its metabolites

This study deals with the nonaqueous capillary electrophoretic separation of dextromethorphan and its metabolites using a methanolic background electrolyte. The optimization of separation conditions was performed in terms of the resolution of dextromethorphan and dextrorphan and the effect of separation temperature, voltage, and the characteristics of the background electrolyte were studied. Complete separation of all analytes was achieved in 40 mM ammonium acetate dissolved in methanol. Hydrodynamic injection was performed at 3 kPa for 4 s. The separation voltage was 20 kV accompanied by a low electric current. The ultraviolet detection was performed at 214 nm, the temperature of the capillary was 25°C. These conditions enabled the separation of four analytes plus the internal standard within 9 min. Further, the developed method was validated in terms of linearity, sensitivity, and repeatability. Rat liver perfusate samples were subjected to the nonaqueous capillary electrophoretic method to illustrate its applicability.     

Capillary zone electrophoresis with a dynamic double coating for analysis of carbohydrate-deficient transferrin in human serum: impact of resolution between disialo- and trisialotransferrin on reference limits

Capillary electrophoresis with a dynamic double coating formed by charged polymeric reagents represents a very effective tool for the separation of iron-saturated transferrin (Tf) isoforms and thus the determination of carbohydrate-deficient transferrin (CDT) in human serum. The resolution between di- and trisialo-Tf is dependent on the applied voltage and capillary temperature. With a 50 microm inside diameter (ID) capillary of about 60 cm total length mounted into the P/ACE MDQ, 28 kV and 40 degrees C, the resolution of the two Tf isoforms is shown to be between 1.0 and 1.4, whereas with reduced voltage and/or temperature, increased resolution at the expense of elongated run times is observed. Best data with complete resolution (Rs > or = 1.4) are obtained at 20 kV and 30 degrees C. For the determination of CDT in serum, incomplete separation of di- and trisialo-Tf is demonstrated to have an impact on the reference limits. Analysis of the sera of 54 healthy individuals with no or moderate alcohol consumption and using valley-to-valley peak integration, the upper (lower) reference limits for CDT in relation to total Tf at the two power levels are 1.33 (0.52) and 1.57 (0.81)%, respectively, representing intervals that are significantly different (P < 0.001). Furthermore, the reference intervals are shown to be strongly dependent on the peak integration approach used. Valley-to-valley peak integration should only be employed for conditions with complete resolution between disialo- and trisialo-Tf.     

Direct chiral resolution of tartaric acid in food products by ligand exchange capillary electrophoresis using copper(II)-D-quinic acid as a chiral selector.

Chiral resolution of native DL-tartaric acid was performed by ligand-exchange capillary electrophoresis using copper(II)-D-quinic acid as a chiral selector. Factors affecting chiral resolution, migration time, and peak area of tartaric acid were studied. The running conditions for optimum separation of tartaric acid were found to be 1 mM copper(II) sulfate-10 mM D-quinic acid (pH 5.0) with an effective voltage of -15 kV at 30 degrees C, using direct detection at 250 nm, and resolution of racemic tartaric acid was approximately 1.3. With this system, chiral resolution of DL-tartaric acid in food products was conducted successfully.     

Chiral separation of benzothiazole derivatives of amino acids using capillary zone electrophoresis

A method for the separation of enantiomers of leucine and phenylalanine benzothiazole derivatives as potential antimicrobial agents was developed using capillary zone electrophoresis with a dual cyclodextrin (CD) system. The best resolution of enantiomers was achieved in 100 mmol/L phosphate background electrolyte (pH 3.5) with the dual CD system consisting of 10 mmol/L of β‐CD with 10 mmol/L of 2‐hydroxypropyl‐β‐cyclodextrin for leucine derivative and 10 mmol/L of 2‐hydroxypropyl‐γ‐cyclodextrin for phenylalanine derivative, respectively. Under the optimal conditions, the highest enantioresolution of 1.25 was achieved in a noncoated‐fused silica capillary at 17°C and 24 kV applied voltage.     

Direct chiral resolution of malic acid in apple juice by ligand-exchange capillary electrophoresis using copper(II)-L-tartaric acid as a chiral selector

Chiral resolution of native DL-malic acid was achieved by ligand-exchange capillary electrophoresis using copper(II)-L-tartrate as a chiral selector. Factors affecting chiral resolution, migration time, and peak area of malic acid were studied. The running conditions for optimum separation of malic acid were found to be 1 mM copper(II) sulfate-1 mM L-tartrate (pH 5.1) with an effective voltage of -20 kV at 30 degrees C, using direct detection at 280 nm, and resolution (Rs) of racemic malic acid was approximately 4. With this system, D- and L-malic acids in apple juice were analyzed successfully.     

On-line sample stacking and short-end injection CE for the determination of fluoxetine and norfluoxetine in plasma: Method development and validation using experimental designs

A short-end injection CE method combining field-amplified sample stacking (FASS) is presented for the analysis of fluoxetine (FL) and norfluoxetine in plasma. In this study, FASS enhanced the sensitivity about 1100-fold, while short-end injection reduced the analysis time to less than 4 min. Parameters involved in the separations were investigated using a central composite design (CCD) and response surface methodology to optimize the separation conditions in a total of only 32 runs. Samples injected into the capillary for 99.9 s at a voltage of -5 kV were stacked in a water plug (0.5 psi, 9 s). Baseline resolution of FL and its major metabolite was achieved using a BGE formulation consisting of phosphate-triethanolamine at low pH, and a separation voltage of -10 kV. Five percent methanol was added as organic modifier to enhance selectivity and resolution. The linear range was between 10 and 500 ng/mL (r >0.9946), covering the expected plasma therapeutic ranges. The LOD in plasma were 4 ng/mL (S/N = 3), a value comparable to that obtained using LC-MS, showing the success of the on-line stacking technique. Our method was also successfully validated in quantification and pharmacokinetic studies with three volunteer plasma samples and could be applied to pharmacogenetic studies.     

Resolution of overlapped peaks of amino acid derivatives in capillary electrophoresis using multivariate curve resolution based on alternating least squares

The application of chemometric techniques to the resolution of overlapped peaks in capillary electrophoresis (CE) is described. When a physical separation can not be completely accomplished, chemometrics might still resolve the determination of the analytes mathematically. CE with diode array detection can provide a large amount of data consisting of spectra registered over time. In this study, the capillary electrophoretic separation of 1,2-naphthoquinone-4-sulfonate derivatives of amino acids is studied. Most of the common amino acid derivatives can be separated at 30 kV in a fused-silica capillary by using a 40 mM sodium tetraborate + isopropanol (3:1 v/v) solution as background electrolyte. However, peaks of certain derivatives (Phe, His, Leu and Ile) still overlap. A multivariate curve resolution method based on an alternating least squares optimization procedure is used for the resolution of the overlapped electrophoretic peaks. The method takes advantage of spectral and electrophoretic differences of analytes to recover their pure electrophoretic and spectral profiles. In addition, each analyte in the mixture can be quantified using the corresponding standards.     

Chiral capillary electrophoretic determination of the enantiomeric purity of tetrahydronaphthalenic derivatives, melatoninergic ligands, using highly sulfated beta-cyclodextrins

Using cyclodextrin capillary zone electrophoresis (CD-CZE), baseline separation of synthetic tetrahydronaphthalenic derivatives, potential melatoninergic compounds, was achieved. A method for the enantioresolution of these tetralins and determination of their enantiomeric purity was developed using anionic CDs (highly sulfated-CD or highly S-CD) as chiral selectors and capillaries dynamically coated with polyethylene oxide (PEO). Operational parameters such as the nature and concentration of the chiral selectors, buffer pH, organic modifiers, temperature and applied voltage were investigated. The use of charged CDs provides a driving force for our neutral compounds in the running buffer and enantiomeric resolution by inclusion of compounds in the CD cavity. The highly S-beta-CD was found to be the most effective complexing agent, allowing good enantiomeric resolution. The complete resolution of three tetralin compounds was obtained using 25 mM phosphate buffer at pH 2.5 containing 2.5% w/v of highly S-beta-CD at 25 degrees C with an applied field of 0.25 kV/cm. The apparent association constants of the inclusion complexes were calculated. This optimized method was validated in terms of linearity, sensitivity, accuracy and recovery. The enantiomeric purity for the three molecules was determined and the detection limit of enantiomer impurities is about 0.3-0.6%.     

Experimental design optimization of the capillary electrophoresis separation of leucine enkephalin and its immune complex

To optimize the capillary electrophoretic separation conditions for leucine enkephalin (LE) and the immune complex of the LE and anti-LE reaction, an analysis using a three-level, three-factorial Box-Behnken design was performed. Three separation parameters, buffer pH (X(1)), buffer concentration (X(2)), and applied voltage (X(3)), were chosen to observe the effect on separation responses. The responses were theoretical plate number, migration time of the LE peak, and resolution between the peaks. The optimum conditions and process validation were determined using statistical regression analysis and surface plot diagrams. The capillary electrophoresis optimum separation conditions were established to be 75 mM phosphate buffer at pH 7.00 with an applied separation voltage of 15 kV. By using the analysis technique, the prediction of responses was satisfactory and process verification yielded values within the +/-5% range of the predicted efficiency.     

卤代乙酸及其结构相近化合物的高效毛细管电泳分离

氟、氯、溴等卤代乙酸是结构非常相近的离子型化合物,对它们的分离测定比较困难。用高效毛细管电泳法在碱性或酸性缓冲液条件下可将它们分离。在酸性缓冲液条件下,可提高有机酸分离的选择性。较低的操作电压有利于提高阴离子的分离度,而改变温度对分离度的影响不大。     

Multivariate optimisation of a cyclodextrin-assisted-capillary zone electrophoretic method for the separation of torasemide and its metabolites

In this work, a rapid cyclodextrin-assisted capillary electrophoretic method is developed for the separation of the diuretic torasemide and three of its metabolites. Both fractional factorial and central composite designs were employed to optimise the separation method. The factors studied were pH, concentration of methyl-β-cyclodextrin, concentration of the background electrolyte and percentage of acetonitrile as organic modifier. Monitored response was a composite quality response (Q*) which balanced conflicting normalized responses, such as resolution and migration time. Optimal separation of the four studied compounds was achieved in less than 6.5 min, using an electrolyte of 60 mM borate buffer with no organic modifier and 25 mM methyl-β-cyclodextrin concentration adjusted to pH 8.0 at a potential of 30 kV. Detection wavelength and temperature were 197 nm and 20 °C respectively. This work means a significant improvement with regard to a previous separation method for these compounds developed in our laboratory.     

Simultaneous determination of dihydroxybenzene positional isomers by capillary electrochromatography using gold nanoparticles as stationary phase

The paper describes the enhanced separation of o-, m-, p-dihydroxybenzene by capillary electrochromatography (CEC) using gold nanoparticles (AuNPs) as stationary phase. The effect of the AuNPs concentration upon separation was investigated. The experimental parameters, including separation voltage, pH, and concentration of running buffer, were optimized. Under the optimum conditions, a good resolution of three dihydroxybenzene isomers was obtained within 15 min in a 50 cm effective length capillary modified with 0.02 nmol/L AuNPs at a separation voltage of 16 kV in a 50 mmol/L acetate buffer (pH 5.0). The linear ranges were from 10(-6) to 10(-4) mol/L and the detection limits were as low as 10(-7) mol/L. This method was successfully used to analysis two kinds of hair coloring agent sample with recoveries in the range of 90-105% and relative standard deviations (RSD) less than 5.0%.     

Enhanced separation of seven quinolones by capillary electrophoresis with silica nanoparticles as additive

This paper describes the enhanced separation of lomefloxacin, sparfloxacin, fleroxacin, norfloxacin, ofloxacin, gatifloxacin and pazufloxacin by capillary zone electrophoresis (CZE) using silica nanoparticles (SiNPs) as running buffer additive. The impact of SiNPs concentration on the resolution and selectivity of separation was investigated and a given value of SiNPs was finally chosen under the optimum conditions. The addition of the SiNPs to the running buffer enabled electroosmotic flow (EOF) decrease and permitted full interaction between SiNPs and analytes. The influence of separation voltage, pH and buffer concentration on the separation in the presence of SiNPs was examined. Interactions between drugs and nanoparticles during the separation are discussed; the determination of interaction constants is also achieved. A good resolution of seven quinolones was obtained within 15 min in a 50 cm effective length fused-silica capillary at a separation voltage of +10 kV in a 12 mM disodium tetraborate-phosphate buffer (pH 9.08) containing 5.2 μg mL⁻¹ SiNPs.     

Optimizing separation conditions for polycyclic aromatic hydrocarbons in micellar electrokinetic chromatography

We report the separation of polycyclic aromatic hydrocarbons (PAHs) using 0.1% poly(ethylene oxide) (PEO) in micellar electrokinetic chromatography (MEKC). In the presence of PEO, adsorption of PAHs on the capillary wall was reduced, leading to better resolution and reproducibility. Effects of tetrapentylammonium iodide (TPAI), dextran sulfate (DS), methanol, and sodium lauryl sulfate (SDS) on the separation of PAHs were elucidated. In terms of resolution and speed, DS, compared to TPAI, is a better additive for separation of PAHs. When using 0.1% PEO solution containing 45% methanol, 50 mM SDS, and 0.02% DS, separation of 10 PAHs containing 2 to 5 benzene rings was accomplished in less than 12 min at 15 kV in a commercial CE system. The method has also been tested for separating seven PAHs with high quantum yields when excited at 325 nm using a He-Cd laser. Unfortunately, separation of the seven PAHs was not achieved and sensitivity diminished under the same conditions. To optimize sensitivity, resolution and speed, a stepwise technique in MEKC has been proposed. The seven PAHs were resolved in 35 min at 15 kV when separation was performed in 0.1% PEO solution containing 35 mM SDS, 40% methanol and 0.02% DS for 2 min, and subsequently in 0.1% PEO solution containing 20 mM SDS, 50% methanol, and 0.02% DS.     

3-苯基乳酸的手性毛细管电泳拆分

考察了环糊精种类、环糊精浓度、缓冲溶液pH、分离电压、温度等因素对3-苯基乳酸手性分离的影响,并对分离条件进行了优化。结果表明,采用区带毛细管电泳技术,以0.03 mol/L的羟丙基-β-环糊精为手性选择剂,0.1 mol/L的磷酸缓冲溶液(pH 5.5)为电泳缓冲溶液,26 kV的分离电压,在25 ℃下可使3-苯基乳酸对映体达到基线分离,分离度为1.51。     

Direct chiral resolution of lactic acid in food products by capillary electrophoresis

Chiral resolution of native DL-lactic acid was performed by capillary electrophoresis using 2-hydroxypropyl-beta-cyclodextrin as a chiral selector. Various factors affecting chiral resolution, migration time, and peak area of lactic acid were studied. The running conditions for optimum separation of lactic acid were found to be 90 mM phosphate buffer (pH 6.0) containing 240 mM 2-hydroxypropyl-beta-cyclodextrin with an effective voltage of -30 kV at 16 degrees C, using direct detection at 200 nm. In order to enhance the sensitivity, sample injection was done under a pressure of 50 mbar for 200 s. On-line sample concentration was accomplished by sample stacking. With this system, D- and L-lactic acids in food products were analyzed successfully.     

Enantiomeric separation by capillary electrochromatography using monolithic capillaries with sol-gel-glued cyclodextrin-modified silica particles

By an on-column sol-gel process, a chiral monolithic stationary phase was prepared by the fusion of permethyl-beta-cyclodextrin-silica (Chira-Dex-silica) particles and by linking them to the internal capillary wall. The resulting monolith is stable toward voltage (30 kV) and pressure (300 bar) and possesses a high efficiency (up to 100,000 theoretical plates per meter). Efficient enantiomeric separation of various chiral compounds by pressure-supported capillary electrochromatography (CEC) was achieved. When comparing this method to capillary liquid chromatography (LC) employing the same column in an unified equipment, CEC shows a twofold higher column efficiency at comparable elution times and hence better resolution factors.