Nonaqueous electrochromatography on continuous bed columns of sol-gel bonded large-pore C18 material: separation of retinyl esters

A nonaqueous electrochromatographic reversed-phase separation method for retinyl esters using continuous bed columns has been developed. The packing material 7 μm Nucleosil 4000 Å C₁₈ was sol–gel bonded in 180 μm I.D. capillaries. The mobile phase used was 2.5 mM lithium acetate in N,N-dimethylformamide–acetonitrile–methanol (2+7+1, v/v). At 350 V/cm and 30°C, this mobile phase composition gave rise to an electroosmotic flow of 1 mm/s. No Joule heating nor bubble formation were observed even at 625 V/cm (17 μA). With a 36 cm L_eff column complete separation of the commercially available and synthesized standards (all-trans-retinyl acetate, palmitate, heptadecanoate, stearate, oleoate, and linoleoate) was obtained within 10 min. The within-day and between-day variations of retention times of all-trans-retinyl palmitate were <0.3% relative standard deviation (RSD) (n=3) and <2% RSD (n=6), respectively. The within-day and between-day variations of peak areas were both <2% (both n=3). The columns were used for more than 1 month without degradation. Liver extracts from arctic seal were analyzed.     

Nonaqueous electrochromatography on C30 columns: separation of retinyl esters.

A nonaqueous packed capillary electrochromatographic reversed-phase method for separation of retinyl esters has been developed. The retinyl esters all-trans-retinyl acetate, palmitate, heptadecanoate, stearate, oleoate, and linoleoate were separated on a 180 microm ID column packed with 5 microm C30 particles with a mobile phase consisting of 2.5 mM lithium acetate in N,N-dimethylformamide-methanol (99:1, v/v). With this mobile phase, the electroosmotic flow was 0.8 mm/s at 650 V/cm and 40 degrees C, and the separation was completed in less than 30 min on 30 cm columns. To obtain electrostable frits of the hydrophobic C30 material both the preparation of the frits and the conditioning of the column prior to electroconditioning were of importance. Selectivity changes were introduced by replacing up to 70% v/v of the N,N-dimethylformamide by acetonitrile. The increase in the amount of acetonitrile was, however, accompanied by a significant increase in analysis time. Liver extracts obtained from arctic seal were analyzed.     

Surface diffusion in reversed-phase liquid chromatography using silica gels bonded with C1 and C18 ligands of different densities

Surface diffusion in reversed-phase liquid chromatography (RPLC) using silica gels bonded with C₁ and C₁₈ alkyl ligands of different densities was studied from the viewpoints of two extrathermodynamic relationships, i.e., enthalpy-entropy compensation (EEC) and linear free energy relationship (LFER). First, according to the four methods proposed by Krug et al., the values of surface diffusion coefficient (D_s) were analyzed to confirm that an actual EEC resulting from substantial physico-chemical effects takes place for surface diffusion. Then, it was also demonstrated that a LFER is observed between surface diffusion and the retention equilibrium. The establishment of EEC and LFER suggests a mechanistic similarity of molecular migration by surface diffusion, irrespective of the alkyl chain length and the densities of C₁ and C₁₈ ligands. Finally, a thermodynamic model for the LFER based on the real EEC was used to estimate D_s values under various RPLC conditions. The D_s values can be estimated with a mean square deviation of about 25–30%. The agreement between the D_s values estimated and those experimentally measured suggests that the total mass flux by surface diffusion consists of the two contributions due to C₁ and C₁₈ ligands and that the contribution of each ligand is proportional to the ligand density.     

Schiff base complex sol–gel method for LaCoO3 perovskite preparation with high-adsorbed oxygen

A novel Schiff base complex sol–gel method has been used to prepare LaCoO₃ producing high ratios of adsorbed (or surface) oxygen (α) to lattice oxygen (β). The as-prepared gels, characterized by Fourier transform infrared spectroscopy (FTIR), showed that both lanthanum and cobalt ions were complexed before calcinations. IR spectra revealed that CO₃²⁻ and NO₃⁻ presented on the sample surfaces during heat treatment. High-resolution transmission electron microscopic (HRTEM) images of all samples showed resolved lattice fringes with the inter-planar spacing 0.37–0.39 nm of the (0 1 2) plane in hexagonal perovskite. BET surface areas of LaCoO₃ nano-crystals were 11.7–18.6 m²/g. Ratios of adsorbed (or surface) oxygen (α) to lattice oxygen (β) quantified by X-ray photoemission spectroscopy showed that LaCoO₃ prepared by the Schiff base complex method produced higher ratios when bases had higher nitrogen content in molecules. Carbonate and nitrate which were resulting from the oxidation of functional groups in the Schiff base complex, can produce gaseous compounds and leave vacant sites for oxygen in the gas phase to adsorb.     

Characterization and evaluation of Fe2O3/Al2O3 oxygen carrier prepared by sol–gel combustion synthesis

The sol-gel combustion synthesis (SGCS) for oxygen carrier (OC) to be used in chemical looping combustion (CLC) was first designed and experimented in this work, which is a new method of OC synthesis by combining sol-gel technique and solution combustion synthesis. Cheap hydrated metal nitrates and urea were adopted as precursors to prepare Fe₂O₃/Al₂O₃ OC at the molar ratio to unity (Fe1Al1), which was characterized through various means, including Fourier transforms infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), differential thermal analysis (DTA), X-ray diffractor (XRD), and N₂ isothermal adsorption/desorption method. FTIR analysis on the chemical structure of the dried gel of Fe1Al1 indicated that urea was partly hydrolyzed and the hydrated basic carbonate was formed by the combination of groups such as (Fe(_1−yAl_y)_1−xO_1−3x, CO₃²⁻ and -OH-. By analyzing the staged products during SGCS, calcination was found as a necessary step to produce Fe₂O₃/Al₂O₃ OC with separate phases of α-Fe₂O₃ and α-Al₂O₃. Through TGA-DTA, the decomposition of the dried gel was found to undergo five stages. The analysis of the evolved gases from the gel decomposition using FTIR partially confirmed the staged decomposition and assisted a better understanding of the mechanism of SGCS. XRD identification further substantiated the necessity of calcination to synthesize Fe₂O₃/Al₂O₃ OC with separate phases of α-Fe₂O₃ and α-Al₂O₃, though it was not necessary for the synthesis of single phase α-Fe₂O₃ and α-Al₂O₃. Structural characterization performed on N₂ adsorption analyzer displayed that the pore shape of Fe1Al1 particles was heterogeneous. Finally, H₂ temperature-programmed reduction (TPR) of Fe1Al1 products in TGA indicated that the reduction reaction of Fe1Al1 OC after calcination was a single step reaction from α-Fe₂O₃ to Fe, and calcination benefited to improve the transfer rate of the lattice oxygen from the OC to fuel H₂. Furthermore, four times of reduction and oxidization (redox) reaction by alternating with H₂ and air demonstrated the synthesized OC had good reactivity and sintering-resistance, much suitable to be used in the realistic CLC. Overall, the SGCS method was found superior to other existent methods to prepare Fe₂O₃/Al₂O₃ OC for CLC application.     

Preparation and characterization of a supported Si3N4 membrane via a non-aqueous sol–gel process

We report a novel fabrication process of a mesoporous Si₃N₄ membrane on an Al₂O₃ support via a non-aqueous sol–gel technique. The membrane was prepared by dipping an -Al₂O₃ support disk into a silicon diimide sol that was synthesized by catalytic ammonolysis of tris(dimethylamino)silylamine, H₂NSi(NMe₂)₃. The SEM image and nitrogen adsorption analysis indicate that amorphous Si₃N₄ layers with nano-sized pores have formed on the surface and also inside the pores of the Al₂O₃ support disk. The new membrane demonstrates high selective absorption of NO₂, suggesting a potential application as a selective filter for gas sensors.     

Donor–acceptor interaction of fullerene C60 with triptycene in molecular complex TPC·C60

A molecular complex of fullerene C₆₀ with triptycene, TPC·C₆₀ is obtained. The complex has a three-dimensional packing of C₆₀ molecules. According to the IR spectra, the freezing of free rotation of C₆₀ molecules in the complex is maintained up to 360 K. The XP-spectra of TPC·C₆₀ show the suppression of π–π^* transitions of TPC phenylene rings. The separation of C₆₀ molecules by TPC ones in TPC·C₆₀ results in low intensity of the C₆₀ transitions in the 420–500 nm range in an optical spectrum. This absorption is assumed as that attributed to intermolecular transitions between adjacent C₆₀ molecules.     

Ion chromatographic separation of alkali metal and ammonium cations on a C18 reversed-phase column

The separation of alkali metal (Li⁺, Na⁺, K⁺, Rb⁺ and Cs⁺) and ammonium cations on a C₁₈ reversed-phase column using three anionic surfactants [sodium 1-eicosyl sulphate, sodium dodecyl benzenesulphonate and sodium dodecyl sulphate (SDS)] is described. Two methods were examined: (a) “permanent” coating, with the use of a C₁₈ reversed-phase column previously coated with the surfactants; and (b) dynamic coating, with addition of the surfactants to the mobile phase. With method (a) the separation of the six cations was achieved with SDS. However, the retention times gradually decreased owing to dissolution of the SDS coating. Good separation was obtained with method (b), where 10 mM HNO₃ containing 0.1 mM SDS was used as the mobile phase with conductivity detection, and it was applied satisfactorily to real samples. The effect of system peaks on determination is also discussed.     

Photodegradation of a textile dye catalyzed by sol–gel derived nanocrystalline TiO2 via ultrasonic irradiation

Nanocrstalline pure anatase titania were prepared by sol–gel process at room temperature followed by ultrasonication (Ti–US). The photocatalytic activity of Ti–US has been evaluated by the degradation of textile dye, Methylene Blue in presence and absence of common inorganic salts (NO₃⁻, C₂O₄²⁻, SO₄²⁻, citrate). It was observed that, in presence of anions, the degradation of the dye increases significantly. The influence of the presence of H₂O₂ on the degradation rate was studied. The dependence of photodegradation of the dye rates on various parameters such as dye concentration, photocatalyst concentration and pH were also investigated. The photodegradation rate follows first order kinetics. H₂O₂ and UV light have a negligible effect in absence of Ti–US catalyst. The relative photonic efficiency of the system is reported using phenol as a standard organic compound.     

Micro-Raman scattering of KTP (KTiOPO4) nanocrystallites synthesized by modified sol–gel Pechini method

KTP nanocrystallites were successfully grown by the modified Pechini method which uses a process for the preparation of the precursor polymeric resin. The products were characterized and examined by back-scattering micro-Raman spectroscopy, X-ray diffraction, FTIR transmission spectroscopy and near normal incidence IR reflection spectroscopy analysis. From the latter study and by using Kramers–Kronig analysis and dispersion relations, we have calculated and reported the typical behavior of real parts of refractive and dielectric indices in the spectral region of 400–4000 cm⁻¹.     

Analysis of C60 and C70 fullerenes using high-performance liquid chromatography–Fourier transform infrared spectroscopy

The performance of Fourier transform infrared spectroscopy (FT-IR) detection coupled to high-performance liquid chromatography for the analysis of C₆₀ and C₇₀ fullerenes was investigated. The isocratic separation method involved an octadecylsilane (ODS) column and an acetonitrile–toluene (1:1) mobile phase. The hyphenated system was designed with a split valve to control eluent volume leading to the FT-IR detector; this allowed for additional coupling of the liquid chromatograph to ultraviolet–visible detection. On-line FT-IR spectra of C₆₀ and C₇₀ were matched with standard off-line FT-IR spectra from the literature. In addition, with band chromatograms individual fullerenes can be identified using FT-IR active modes known specifically for each fullerene. Few changes to a pre-existing HPLC–UV method were necessary for the HPLC–FT-IR method, and there was no need for fraction collection to identify the fullerenes C₆₀ and C₇₀.     

Reaction of allylic and benzylic alcohols and esters with PPh3/I2: one-pot synthesis of β,γ-unsaturated compounds

The treatment of tertiary and secondary allylic alcohols containing a terminal double bond, and their acetyl derivatives, with triphenylphosphine and iodine under mild conditions leads regiospecifically and in high stereoselectivity to the corresponding primary allylic iodides, which can react ‘in situ’ with diverse nucleophiles. Primary allylic alcohols and benzyl alcohols and acetates are also transformed into the corresponding iodides under these conditions.     

Expeditious synthesis of a key C9–C21 subunit of the aplyslatoxine and oscillatoxins

The C₉–C₂₁ portion of the aplysiatoxin/oscillatoxin bluegreen algal metabolites was synthesized as the 9-aldehyde bearing a tert-butyldimethylsilyl ether group on the C₁₁ hydroxyl and a trimethylsilylethoxymethyl ether group on the C₂₀ hydroxyl. Featuring an asymmetric aldol and an asymmetric oxazaborolldine reduction, the synthesis proceeded with high (>90%) stereoselectivity in 13 steps and 5–7% overall yield from commercial starting material.     

Cobalt phthalocyanine derivatives supported on TiO2 by sol–gel processing: Part 2. Activity in sulfide and ethanethiol oxidation

The catalytic activity of cobalt(II) 2,9,16,23-tetrasulphophthalocyanine and cobalt(II) 2,9,16,23-tetra(chlorosulphonyl)phthalocyanine covalently bonded to a TiO₂ matrix by sol–gel processing was investigated for sulfide and ethanethiol (CH₃CH₂SH) liquid-phase oxidation. A comparison of the kinetic data as well as the state of active component by using electron spectroscopy in dependence on precursors was carried out. Kinetic data shows that the most stable and active catalysts for ethanethiol oxidation are both CoPc(SO₃H)₄ and CoPc(SO₂Cl)₄ in TiO₂ from Ti(OⁱPr)₄, whereas in the case of Na₂S oxidation in neutral medium the activity of the former is higher.     

Preparation of polyimide/silica hybrid material by sol–gel process under basic catalysis: Comparison with acid conditions

Hybrid polyimide/silica materials were prepared from polyimides bearing reactive functions along the polymer backbone, which can react with. The silica phase was formed by sol–gel process using ammonium hydroxide catalyst. Silica fillers prepared under basic conditions were compared with materials prepared using chlorhydric acid. The synthesized hybrid materials were characterized by TGA, IRTF, and NMR. The density of the different systems was also measured. The morphology of these hybrid systems were investigated by both scanning and transmission electron microscope. Thermal properties of the composites were also evaluated by DSC and DMA. The morphology of silica fillers highly depends on the catalyst, on the reaction conditions of the sol–gel process, and the linking formation with the polyimide. It results that optimized conditions lead to homogeneous hybrid films containing 12 wt % of silica particles of about 20 nm. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1891–1902, 2008     

Sol–gel derived nano-crystalline CaSnO3 as high capacity anode material for Li-ion batteries

CaSnO₃ with the distorted-perovskite structure was prepared by sol–gel and high temperature solid-state reaction and electrochemical properties were studied in cell with Li as counter electrode. The sol–gel method gave uniform nano-crystallites (200–300 nm) of CaSnO₃ and was shown to deliver a reversible capacity of 380 mAh/g (0.005–1.0 V; 60 mA/g) with good cycling stability up to 45 cycles. The observed capacity involved in the first-discharge and the reversible capacity values during subsequent charge–discharge cycles show that the electrochemical process in CaSnO₃ is similar to other Sn-containing mixed oxide systems, viz., an initial structural reduction with Sn-metal formation followed by reversible Li–Sn alloy formation. The performance with respect to the attainable capacity, its retention on charge–discharge cycling and rate capability is better than the previously reported best-performing bulk Sn-oxide or ATCO starting materials which reveals that the perovskite structure and Ca-ion play a beneficial role.     

Barium alginate caged Fe3O4@C18 magnetic nanoparticles for the pre-concentration of polycyclic aromatic hydrocarbons and phthalate esters from environmental water samples

The hydrophobic octadecyl (C₁₈) functionalized Fe₃O₄ magnetic nanoparticles (Fe₃O₄@C₁₈) were caged into hydrophilic barium alginate (Ba²⁺-ALG) polymers to obtain a novel type of solid-phase extraction (SPE) sorbents, and the sorbents were applied to the pre-concentration of polycyclic aromatic hydrocarbons (PAHs) and phthalate esters (PAEs) pollutants from environmental water samples. The hydrophilicity of the Ba²⁺-ALG cage enhances the dispersibility of sorbents in water samples, and the superparamagnetism of the Fe₃O₄ core facilitates magnetic separation. With the magnetic SPE technique based on the Fe₃O₄@C₁₈@Ba²⁺-ALG sorbents, it requires only 30 min to extract trace levels of analytes from 500 mL water samples. After the eluate is condensed to 0.5 mL, concentration factors for both phenanthrene and di-n-propyl-phthalate are over 500, while for other analytes are about 1000. The recoveries of target compounds are independent of salinity and solution pH under testing conditions. Under optimized conditions, the detection limits for phenanthrene, pyrene, benzo[a]anthracene, and benzo[a]pyrene are 5, 5, 3, and 2 ng L⁻¹, and for di-n-propyl-phthalate, di-n-butyl-phthalate, di-cyclohexyl-phthalate, and di-n-octyl-phthalate are 36, 59, 19, and 36 ng L⁻¹, respectively. The spiked recoveries of several real water samples for PAHs and PAEs are in the range of 72-108% with relative standard deviations varying from 1% to 9%, showing good accuracy of the method. The advantages of the new SPE method include high extraction efficiency, short analysis time and convenient extraction procedure. To the best of our knowledge, it is unprecedented that hydrophilic Ba²⁺-ALG polymer caged Fe₃O₄@C₁₈ magnetic nanomaterial is used to extract organic pollutants from large volumes of water samples.     

Higher trifluoromethylated derivatives of C60, C60(CF3)16 and C60(CF3)18: Synthesis, structure, and theoretical study

Three isomers of C₆₀(CF₃)₁₆ and one isomer of C₆₀(CF₃)₁₈ have been isolated by HPLC from a mixture prepared by trifluoromethylation of C₆₀ with CF₃I in a glass ampoule at 380-400 °C. The molecular structures of the four new compounds have been determined by means of X-ray single crystal diffraction and discussed in terms of mechanistic pathways of their formation and relative stability according to the DFT calculations.     

Gas chromatography of homologous esters : XXVIII. Retention increments of aliphatic C1---C18n-alkyl esters of butanoic acid and its monochloro derivatives on SE-30 and OV-351 capillary columns

The retention behaviour of C₁---C₁₈n-alkyl esters of butanoic 2-, 3- and 4-chlorobutanoic acids was examined isothermally at several temperatures on SE-30 and OV-351 capillary columns. Retention increments showing the effects of each position of chlorine substitution are presented. The considerable enhancement of terminal chlorine substitution is discussed together with the corresponding behaviour of the monochloropropanoate esters.     

Preparative and spectral investigations on C3 bonded acetylacetonates of tellurium(IV)

In the reaction of 3,3-bis(chloromercury)-2,4-pentanedione with TeCl₄, Ph₂TeCl₂, or Ph₃TeCl, the replacement of one HgCl group by a tellurium moiety gives Cl₃Te(C₅H₆O₂)HgCl·2C₄H₈O₂ (I), Ph₂Te(Cl)(C₅H₆O₂)HgCl (II) and Ph₃Te(C₅H₆O₂)HgCl (III), respectively. The IR and ¹H NMR data indicate that the Te is bonded to the C₃ carbon of acetylacetone. In solution the compounds appear to ionize into Cl⁻ and an organometallic cation in which Hg seems to be involved in secondary interaction with the carbonyl groups; far IR and mass spectral data suggest that Hg---O interaction is significant even in solid state.