应力场对多层膜Permalloy/Cu/Co/NiO铁磁共振性质影响的理论研究

采用能量极小原理研究了Permalloy(Py)/Cu/Co/Ni O多层膜结构中层间耦合强度和应力各向异性场对薄膜共振频率的影响,得到共振频率随外磁场强度变化关系式.结果发现外应力场强度和方向对系统共振频率的影响在本文中要强于层间耦合强度和交换各向异性场,外应力场方向对光学模共振频率的影响强于声学模,而外应力场强度对声学模共振频率的影响强于光学模.     

溅射制备的Co/V多层膜微观结构特征与铁磁共振研究

研究了用射频磁控溅射方法制备的［Co(1.5nm)/V(d_V)］₂₀(0.5nm≤d_V≤4nm)多层膜的结构和磁性.用X射线衍射、透射电子显微镜、高分辨率透射电子显微镜等手段对其结构的分析,表明它们层状周期结构良好,沿膜的生长方向具有fcc Co(111)和bcc V(110)织构,且是由小的柱状晶粒构成的多晶薄膜.界面一定程度的合金化,使其成为成分调制周期结构,也是它们的一个结构特征.由其铁磁共振谱计算得到较小的g因子和4πM_{e 关键词：}     

应力各向异性下耦合三层薄膜铁磁共振

研究铁磁/铁磁/反铁磁三层薄膜中应力各向异性场对共振场的影响.得到系统存在声学和光学两种模,并且随着应力场的增强,在某些区域声学模和光学模共振场均向高值方向移动.此外发现声学模共振场对两铁磁层厚度的依赖较大,对光学模而言,随着两铁磁层厚度的改变,应力各向异性场对其共振场的影响甚微.     

Fe/[NiFe/Cu]30多层膜线列阵的铁磁共振研究

用铁磁共振(FMR)技术研究Fe/［NiFe/Cu］₃₀多层膜线列阵的特性,线列阵采用激光全息光刻和离子束刻蚀技术加工,线密度为250线/mm和500线/mm.线列阵样品的FMR谱在稍高于主峰（声学峰）的共振场下有光学峰出现,相当层间交换耦合为反铁磁型.光学峰与声学峰的峰位间距沿易轴小于沿难轴.又,来自非磁Cu夹层的顺磁共振峰的幅度远大于原始的连续膜,说明线列阵加工致使层结构退化. 关键词：     

外应力场下双层铁磁薄膜中的铁磁共振性质

用铁磁共振方法得到了双层铁磁薄膜的色散关系解析表达式.发现共振场依赖于层间耦合强度和应力场.假定层间为反铁磁性耦合，且铁磁层Ａ有较强的平面内各向异性.随着外磁场的增强，铁磁层Ｂ中的磁化强度突然由最初的反平行转为平行，从而导致色散曲线的阶跃，并且发现光学模阶跃幅度比声学模大.随着应力场的增强，Ｂ层中磁化强度反转所需的外磁场减弱.此外，在不同的交换耦合强度和应力场下，光学模共振场对外磁场方向的依赖性较强. 关键词： 双层铁磁薄膜 界面相互作用 应力各向异性场 铁磁共振     

磁控溅射Fe/Mo多层膜的巨磁电阻及层间耦合

研究了DC/RF磁控溅射Fe/Mo多层膜的磁电阻特性.在反铁磁性耦合的样品中,观察到了磁电阻比率约为12%的巨磁电阻效应.当Mo层厚度改变时,还观察到了周期约为1.0—1.2nm的层间耦合振荡.另外,F/Mo多层膜的磁电阻比率不仅随Mo层厚度改变出现振荡,而且与Fe层厚度的改变也有着很强的依赖关系. 关键词：     

Pt插层对Co/FeMn界面的影响

采用磁控溅射的方法制备了Co/FeMn/Co多层膜,研究了Co（底部）/FeMn和FeMn/Co（顶部）界面插入Pt层后磁矩的变化情况．通过测量磁滞回线可知,Co（底部）/FeMn界面的Pt插层改变了体系的饱和磁化强度Ｍ_s,随着Co层厚度（t_Co）的增加Ｍ_s不断趋近于Co块体结构理论值1440 kA/m．这是因为Co（底部）/FeMn界面产生了净磁矩,而界面处的Pt插层可以减少这种净磁矩的产生．但是 关键词： 磁性多层膜 垂直磁各向异性 交换耦合     

Co/Ni多层膜垂直磁各向异性的研究

采用直流磁控溅射法在玻璃基片上制备了Pt底层的Co/Ni多层膜样品, 对影响样品垂直磁各向异性的各因素进行了调制, 通过样品的反常霍尔效应系统的研究了Co/Ni多层膜的垂直磁各向异性. 结果表明, 多层膜中各层的厚度及周期数对样品的反常霍尔效应和磁性有重要的影响. 通过对多层膜各个参数的调制优化, 最终获得了具有良好的垂直磁各向异性的Co/Ni多层膜最佳样品Pt(2.0)/Co(0.2)/Ni(0.4)/Co(0.2)/Pt(2.0), 经计算, 该样品的各向异性常数K_eff 达到了3.6×10⁵ J/m³, 说明样品具备良好的垂直磁各向异性. 最佳样品磁性层厚度仅为0.8 nm, 样品总厚度在5 nm以内, 可更为深入的研究其与元件的集成性.     

应力各向异性对铁磁/反铁磁双层薄膜磁性质的影响

 采用铁磁共振方法,研究了交换各向异性和应力各向异性对铁磁/反铁磁双层薄膜性质的影响。结果表明：界面交换作用导致单向各向异性,应力各向异性对材料的磁化难易程度有较大影响。在外磁场方向接近应力场方向时,共振频率向高值方向移动,其它区域共振频率则向低值方向移动。对频率线宽而言,接近应力场方向,频率线宽加宽,其它区域频率线宽则变窄。此外,当磁场变化时,应力的存在使得共振频率向低值方向移动,尤其在β＝π方向情况较为复杂,在弱场范围出现了两个区域：即在某磁场范围内,共振频率向高值方向移动,且频率线宽加宽;而其它范围的共振频率（线宽）是向高值方向移动（加宽）还是向低值方向移动（变窄）,取决于外磁场的相对强弱。     

磁性多层膜层间交换耦合的自由电子模型研究

基于自由电子模型,考虑到不同膜厚和不同磁化排列的费密能的不同,自洽地给出费密能。利用这种方法,计算了材料铁磁层和非磁层电子密度对层间耦合振荡周期的影响,并比较了我们所得结果与他人按巨势法得到的结果的异同,发现振荡周期随着电子密度的变化而改变,并且当铁磁层和非磁层的电子密度不同时,将出现不等周期的振荡。这一新的理论结果与最近的实验相符。此外,还计算了极化强度和由于能带不匹配造成的接触势对耦合强度及振荡相位的影响:前者是决定耦合强度的主要因素,后者则会影响振荡相位,甚至周期。 关键词：     

双层磁性薄膜系统中铁磁共振性质

利用能量极小原理研究了双层磁性薄膜系统中的铁磁共振特性,给出共振频率与线宽随外加磁场的变化关系.以及考虑应力各向异性、交换各向异性和单轴各向异性后,系统共振频率与线宽的变化情况.数值计算结果表明:外应力场和交换各向异性场对铁磁共振频率、频谱宽度以及磁化行为均有影响.     

Magnetic properties of Fe/ZnSe/Fe trilayers

The magnetic properties of Fe/Zn/Fe trilayers have been studied by ferromagnetic resonance and magnetization measurements. These measurements have been used to investigate the magnetic anisotropy of the iron layers and the magnetic coupling across the semiconductor spacer. The angular dependence of the resonance spectra has been measured in-plane and out-of-plane in order to deduce magnetic anisotropy constants of the samples. Experimental data were fitted by using an energy-density expression that includes bulk cubic anisotropy, growth-induced uniaxial in-plane anisotropy and perpendicular-surface anisotropy terms. A small ferromagnetic coupling is observed in the trilayers with spacer thickness up to .     

Dynamic response of permalloy/Cu/Co magnetoresistive sandwiches

The dynamic response of trilayer magnetoresistive permalloy/Cu/Co films was studied by high-frequency permeability spectra measurements. The resonance frequency is shown to depend on the interlayer copper thickness. This dependence is related to exchange coupling between permalloy and cobalt and the interaction field is estimated using the Landau–Lifschitz–Gilbert model.     

Oscillatory ferromagnetic interlayer coupling in [Pt(5 Å)/Co(4 Å)]3/Cr(x Å)/[Co(4 Å)/Pt(12 Å)]3 multilayers with perpendicular anisotropy

Investigation has been performed on the interlayer coupling between two Co/Pt multilayers with perpendicular anisotropy separated by Cr spacers. As a function of the Cr spacer thickness, only ferromagnetic interlayer coupling has been observed between the two Co/Pt multilayers in contrast to the oscillatory interlayer coupling between ferromagnetic and antiferromagnetic observed in ferromagnetic layers with in-plane anisotropy separated by Cr spacers. It is the strength of the ferromagnetic interlayer coupling that has been observed to be oscillatory as a function of the Cr spacer thickness with a period of about 7 Å.     

Ferromagnetic resonance investigation of nanocrystalline FeCuNbSiB

An elaborate line-shape analysis of the ferromagnetic resonance (FMR) spectra taken in the temperature range 100 K to 350 K on amorphous FeCuNbSiB alloys before and after nanocrystallizing them reveals that in the nanocrystalline state, (i) spin wave stiffness (D) is enhanced while the saturation magnetization,M _S, is reduced, (ii) both the ‘in-plane’ anisotropy field,H _K, as well as the FMR line-width scale with MS, (iii) the single-ion anisotropy of spin-orbit plus crystal field origin dominates over the twoion anisotropy of dipolar origin and (iv) multi-magnon scattering contributions to FMR line-width become important in some cases     

Ferromagnetic resonance and magnetization in permalloy films with nanostructured antidot arrays of variable size

We present the results of structural and magnetic characterization of Permalloy (Fe₂₀Ni₈₀) films deposited by sputtering on self-organized nanoporous alumina previously treated with phosphoric acid to vary the pore diameters. SEM and AFM images of the top film surfaces show a triangular array of pores with diameters similar to the untreated porous alumina. However, the underlying pore enlargement is evidenced by the magnetic study. Indeed magnetization measurements reveal a decrease in the easy-plane anisotropy energy with elapsing time of chemical etching. Consistent with these results, ferromagnetic resonance measurements perpendicular to the film indicate a systematic reduction of the resonance field which can be directly related to an increase in the pore diameter. The effect of lateral confinement (due to the pores) in the spin-wave resonance is evidenced in multiple absorption lines when the applied field is in the film plane and perpendicular to it. This contrasts with the results for the continuous test film.     

Dependence of the ferromagnetic resonance modes on the coupling strength in exchange-coupled trilayer structures

The dependence of the dispersion relation and the magnetization on the exchange coupling strength was calculated for a system consisting of two ferromagnetic layers exchange-coupled through a nonmagnetic spacer layer. The magnetic layers are characterized by both uniaxial and cubic magnetocrystalline anisotropies. A minimization procedure was developed which allows the resonance modes to be obtained for any magnetic field orientation and strength, as well as for any exchange coupling strength. If the antiparallel coupled film is unsaturated at resonance, the dispersion relation for both acoustic and optic modes could be rather complex, especially when the field is applied in the plane of the film.     

The effect of substrate on magnetic properties of Co/Cu multilayer nanowire arrays

Ordered Co/Cu multilayer nanowire arrays have been fabricated into anodic aluminium oxide templates with Ag and Cu substrate by direct current electrodeposition. This paper studies the morphology, structure and magnetic properties by transmission electron microscopy, selective area electron diffraction, x-ray diffraction, and vibrating sample magnetometer. X-ray diffraction patterns reveal that both as-deposited nanowire arrays films exhibit face-centred cubic structure. Magnetic measurements indicate that the easy magnetization direction of Co/Cu multilayer nanowire arrays films on Ag substrate is perpendicular to the long axis of nanowire, whereas the easy magnetization direction of the sample with Cu substrate is parallel to the long axis of nanowire. The change of easy magnetization direction attributed to different substrates, and the magnetic properties of the nanowire arrays are discussed.     

Ferromagnetic resonance study of sputtered Co|Ni multilayers

We report on room temperature ferromagnetic resonance (FMR) studies of [ t Co|2t Ni]  × N sputtered films, where 0.1 ≤ t ≤ 0.6 nm. Two series of films were investigated: films with the same number of Co|Ni bilayer repeats (N = 12), and samples in which the overall magnetic layer thickness is kept constant at 3.6 nm (N = 1.2/t). The FMR measurements were conducted with a high frequency broadband coplanar waveguide up to 50 GHz using a flip-chip method. The resonance field and the full width at half maximum were measured as a function of frequency for the field in-plane and field normal to the plane, and as a function of angle to the plane for several frequencies. For both sets of films, we find evidence for the presence of first and second order anisotropy constants, K₁ and K₂. The anisotropy constants are strongly dependent on the thickness t, and to a lesser extent on the total thickness of the magnetic multilayer. The Landé g-factor increases with decreasing t and is practically independent of the multilayer thickness. The magnetic damping parameter α, estimated from the linear dependence of the linewidth ΔH, on frequency, in the field in-plane geometry, increases with decreasing t. This behaviour is attributed to an enhancement of spin-orbit interactions with decreasing Co layer thickness and in thinner films, to a spin-pumping contribution to the damping.