Development of new polar monolithic coatings for stir bar sorptive extraction

Polar vinyl monomers have been used for the synthesis of several polymer monoliths, to serve as novel coatings for stir bar sorptive extraction; the monovinyl monomers 2‐hydroxyethyl methacrylate (HEMA) and poly(ethylene glycol) monomethacrylate) (PEGMA) were copolymerized with (apolar) divinylbenzene (DVB) and/or pentaerythritol triacrylate (PETRA), both of which are cross‐linking agents. After the optimization of the most important synthesis parameters, which included the ratio between total monomers and porogen, the nature of the porogen, and the monomer ratios, inter alia, three mechanically stable, polar monolithic coatings for stir bar sorptive extraction were obtained that were based on poly(HEMA‐co‐DVB), poly(HEMA‐co‐PETRA), and poly(PEGMA‐co‐PETRA). Thereafter, and in order to evaluate the hydrophilicity of the resulting monoliths, they were applied as materials in the stir bar sorptive extraction of a group of emerging pollutants with a wide range of polarities. The results showed that both the poly(HEMA‐co‐DVB) and poly(PEGMA‐co‐PETRA) materials could be used to extract both polar and nonpolar compounds by stir bar sorptive extraction, in an effective manner. Taking into account the desired chemical and morphological properties, as well as the extraction efficiencies, the poly(PEGMA‐co‐PETRA) material seemed to be a particularly promising monolith for application as a novel coating in stir bar sorptive extraction.     

Comparison of in-tube sorptive extraction techniques for non-polar volatile organic compounds by gas chromatography with mass spectrometric detection

A commercial in-tube sorptive extraction device, known as solid-phase dynamic extraction (SPDE), has been evaluated for the extraction of non-polar volatile aromatic analytes from aqueous solutions in both headspace and liquid injection modes. An automated sampler is used with a gas-tight 2.5 ml syringe equipped with a special needle that is coated on the inside with a non-polar extraction phase. After absorption onto the phase, the analytes were thermally desorbed directly into a GC-MS system. The technique was evaluated for the determination of furan, benzene and toluene. The sensitivity for toluene was greatly improved on using SPDE compared to static headspace. A slight increase in sensitivity was observed for benzene but none for determination of furan. Estimated limits of detection ranged from 0.2 to 2 microg/l.     

Ion-pair sorptive extraction of perfluorinated compounds from water with low-cost polymeric materials: Polyethersulfone vs polydimethylsiloxane

A method for the determination of seven perfluorinated carboxylic acids and perfluorooctane sulphonate (PFOS) in aqueous samples using low-cost polymeric sorptive extraction as sample preparation technique, followed by liquid chromatography–tandem mass spectrometry (LC–MS/MS) determination has been developed and validated. Simplicity of the analytical procedure, low volume of solvent and sample required, low global price and a good selectivity providing cleaner extracts are the main advantages of this extraction technique. Polydimethylsiloxane (PDMS) and polyethersulfone (PES) materials were evaluated and compared to achieve the best extraction efficiencies. Hence, different variables have been optimized, viz.: sample pH, concentration of an ion-pairing agent (tetrabutylammonium), ionic strength, sample volume, extraction time, desorption solvent volume, desorption time and the need for auxiliary desorption techniques (sonication). Overall, PES leaded to a better sensitivity than PDMS, particularly for the most polar compounds, reaching detection limits (LODs) in the 0.2–20 ng L⁻¹ range. The precision of the method, expressed as relative standard deviation (RSD), was lower than 16%. Finally, the PES material was employed for the analysis of sea, sewage and fresh water samples. Perfluoroheptanoic acid (PFHpA), perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA) and perfluorodecanoic acid (PFDA) were detected in all the analyzed influent samples reaching levels of up to 401 ng L⁻¹. In surface water, perfluorohexanoic acid (PFHxA) exhibited the highest concentrations, up to 137 ng L⁻¹.     

A novel stir bar sorptive extraction coating based on monolithic material for apolar, polar organic compounds and heavy metal ions

In this study, a novel stir bar sorptive extraction (SBSE) based on monolithic material (SBSEM) was prepared. The monolithic material was obtained by in situ copolymerization of vinylpyrrolidone and divinylbenzene in the presence of a porogen solvent containing cyclohexanol and 1-dodecanol with azobisisobutyronitrile as initiator. The influences of polymerization conditions on the extraction efficiencies were investigated, using phenol and p-nitrophenol as detected solutes. The monolithic material was characterized by various techniques, such as elemental analysis, scanning electron microscopy, mercury intrusion porosimetry, infrared spectroscopy. Polycyclic aromatic hydrocarbons were used to investigate the extraction efficiencies of SBSEM for apolar analytes. Hormones, aromatic amines and phenols were selected as test analytes to investigate the extraction efficiencies of SBSEM for weakly and strongly polar compounds. The results showed that the new SBSEM could enrich the above-mentioned organic compounds effectively. It is worthy to mention that the SBSEM can enrich some heavy metal ions, such as Cu²⁺, Pb²⁺, Cr³⁺ and Cd²⁺, through coordination adsorption. To our best knowledge, that is the first to use SBSE to enrich heavy metal ions.     

Evaluation of extraction techniques for butyltin compounds in sediment

There have been many methods available for the determination of butyltin compounds in sediment. The variations of these methods are not in the methods of determination but rather in the extraction of these compounds from the complex matrices. All of these methods have not been critically compared or evaluated, mainly because of the lack of a suitable reference sediment for butyltin compounds. Recently, the National Research Council of Canada has introduced a reference sediment (PACS-1) which contains certified values of butyltin compounds. The present study compares the recoveries of ten extraction techniques for butyltin species using ethylation derivatization and GC AA as the method of determination. Of these ten methods, only four were found satisfactory for extraction of the dibutyltin and tributyltin species. None of the methods evaluated, however, could quantitatively extract monobutyltin from sediment.     

Evaluation of low-cost disposable polymeric materials for sorptive extraction of organic pollutants in water samples

The capabilities of four commercially available and low cost polymeric materials for the extraction of polar and non-polar contaminants (log K_ow = −0.07–6.88, from caffeine to octocrylene, respectively) from water samples was compared. Tested sorbents were polyethersulphone, polypropylene and Kevlar, compared to polydimethylsiloxane as reference material. Parameters that affect the extraction process such as pH and ionic strength of the sample, extraction time and desorption conditions were thoroughly investigated. A set of experimental partition coefficients (K_pw), at two different experimental conditions, was estimated for the best suited materials and compared with the theoretical octanol–water (K_ow) partition coefficients of the analytes. Polyethersulphone displayed the largest extraction yields for both polar and non-polar analytes, with higher K_pw and lower matrix effects than polydimethylsiloxane and polypropylene. Thus, a sorptive microextraction method, followed by large volume injection (LVI) gas chromatography–tandem mass spectrometry (GC–MS/MS), was proposed using the former sorbent (2 mg) for the simultaneous determination of model compounds in water samples. Good linearity (>0.99) was obtained for most of the analytes, except in the case of 4-nonylphenol (0.9466). Precision (n = 4) at 50 and 500 ng L⁻¹ levels was in the 2–24% and limits of detection (LODs) were in the 0.6–25 ng L⁻¹ range for all the analytes studied.     

Analysis of wine primary aroma compounds by stir bar sorptive extraction

Due to the great importance of some primary aroma compounds on wine quality, these compounds which includes terpenes, C₁₃-norisoprenoids and C₆ compounds, have been analyzed by stir bar sorptive extraction (SBSE) followed by a thermal desorption-gas chromatography-mass spectrometry analysis. The stir bar sorptive extraction method was optimized in terms of temperature, time, pH and NaCl addition. The best SBSE sorption kinetics for the target analytes were obtained after submitting the solutions to 60 °C during 90 min. The addition of sodium chloride did not enhance the volatile extraction. The method proposed showed good linearity over the concentration range tested, with correlation coefficients higher than 0.98 for all the analytes. The reproducibility and repeatability of the method was estimated between 0.22 and 9.11%. The detection and quantification limits of all analytes were lower than their respective olfactory threshold values. The application of this SBSE method revealed that monovarietal white wines were clearly separated by two canonic discriminating functions when grape varieties were used as differentiating variable, the first of which explained 98.4% of the variance. The compounds which contributed most to the differentiation were limonene, linalool, nerolidol and 1-hexanol.     

New hydrophilic polymeric resin based on 4-vinylpyridine-divinylbenzene for solid-phase extraction of polar compounds from water

A 4-vinylpyridine-divinylbenzene (VP-DVB) resin was synthesized to be used for on-line solid-phase extraction process and it was tested for a group of polar compounds. The high specific surface area and the nitrogen content of the VP-DVB sorbent increased the interactions with the polar analytes in the preconcentration process. The sorbent enabled 100 ml of water to be concentrated with recoveries higher than 70% for several polar compounds (including phenol) except for oxamyl (55%) and methomyl (43%). The method was used to analyse water samples by liquid chromatography and UV detection. Linearity was good and detection limits were 0.1-0.2 microg l(-1) for all compounds. Several tap and river water and waste water treatment plant samples were analyzed; phenol and (4-chloro-2-methyl-phenoxy)acetic acid (MCPA) were tentatively determined in some samples.     

Optimization and validation of headspace sorptive extraction for the analysis of volatile compounds in wine vinegars

Quantification of aroma compounds in wine vinegars is challenging due to the complexity of the matrix and the low concentrations expected. A method for the determination of volatile compounds in wine vinegars employing headspace sorptive extraction-thermal desorption-gas chromatography-mass spectrometry (HSSE-TD-GC-MS) was developed. A central composite design was used to optimize the sampling condition. The proposed method was successfully validated and low detection and quantification limits was obtained. The application of the proposed methodology allows the determination of 53 compounds in different wine vinegars (red, Sherry). Five of them have been detected in wine vinegars for the first time.     

Stir bar sorptive extraction for trace analysis

Stir bar sorptive extraction (SBSE) was introduced in 1999 as a solventless sample preparation method for the extraction and enrichment of organic compounds from aqueous matrices. The method is based on sorptive extraction, whereby the solutes are extracted into a polymer coating on a magnetic stirring rod. The extraction is controlled by the partitioning coefficient of the solutes between the polymer coating and the sample matrix and by the phase ratio between the polymer coating and the sample volume. For a polydimethylsiloxane coating and aqueous samples, this partitioning coefficient resembles the octanol-water partitioning coefficient. In comparison to solid phase micro-extraction, a larger amount of sorptive extraction phase is used and consequently extremely high sensitivities can be obtained as illustrated by several successful applications in trace analysis in environmental, food and biomedical fields. Initially SBSE was mostly used for the extraction of compounds from aqueous matrices. The technique has also been applied in headspace mode for liquid and solid samples and in passive air sampling mode. In this review article, the principles of stir bar sorptive extraction are described and an overview of SBSE applications is given.     

Development of a stir bar sorptive extraction method for the determination of volatile compounds in orange juices

A stir bar sorptive extraction method for the determination of volatile compounds in orange juices was developed. The extraction variables were optimized using a reduced two‐level factorial screening design (2^5‐1), and the most suitable analytical conditions for the extraction of the studied compounds were: sample volume 10 mL, extraction time 60 min, stirring speed 1800 rpm, NaCl amount 30% (weight/volume), and twister length 10 mm. The optimized method was further validated, obtaining good linearity and detection and quantification limits low enough to correctly determine the studied compounds. As well, for most of the studied compounds precision and recovery values were good. Several orange juice samples (squeezed and commercial) were extracted following the optimized extraction method and analyzed by gas chromatography coupled to mass spectrometry detection. The method has proven to be suitable for the determination of the aroma of orange juice, of which limonene was the major volatile compound in all the studied samples.     

Passive sampling and stir bar sorptive extraction for the determination of endocrine-disrupting compounds in water by GC-MS

A new method using the extraction and preconcentration capabilities of stir bar sorptive extraction, combined with high-resolution gas chromatography and mass spectrometry, was developed for the determination of five selected endocrine-disrupting compounds (4-n-nonylphenol, bisphenol A, estrone, 17β-estradiol, and 17α-ethinylestradiol) in water. In situ derivatization to transform the phenolic compounds into lipophilic and volatile analytes was carried out with acetic anhydride. Two different methods of headspace derivatization to further improve the chromatographic properties of 17β-estradiol and 17α-ethinylestradiol were developed and compared. The optimized method provided good sensitivity (limits of quantitation 1.2–2.6 ng), repeatability (relative standard deviation 2–9%), and reproducibility (relative standard deviation 10–17%). Passive sampling by means of polar organic chemical integrative samplers was applied to monitor river waters used as supply sources for drinking water treatment plants in the Liguria region of Italy. The analytes showed a different distribution at the three sites considered; bisphenol A proved to be the most abundant, ranging from 185 to 459 ng per sampler.     

New sorbents for extraction and microextraction techniques

This review outlines recent progress in the research on some new classes of sorbents for extraction and microextraction techniques. Carbon nanotubes are allotropes of carbon with cylindrical structure. They are very stable systems having considerable chemical inertness due to the strong covalent bonds of the carbon atoms on the nanotube surface. Some applications of carbon nanotubes are presented in a perspective view. Molecular imprinting has proved to be an effective technique for the creation of recognition sites on a polymer scaffold. By a mechanism of molecular recognition, the molecularly imprinted polymers are used as selective tools for the development of various analytical techniques such as liquid chromatography, capillary electrochromatography, solid-phase extraction (SPE), binding assays and biosensors. Sol–gel chemistry provides a convenient pathway to create advanced material systems that can be effectively utilized to solve the solid phase microextraction fiber technology problems. This review is mainly focused on recent advanced developments in the design, synthesis and application of sol–gel in preparation of coatings for the SPME fibers.     

Development and application of a polar coating for stir bar sorptive extraction of emerging pollutants from environmental water samples

In the present study, a stir bar coated with hydrophilic polymer based on poly(N-vinylpyrrolidone-co-divinylbenzene) was prepared for the sorptive extraction of polar compounds. The main parameters affecting the polymerisation of the coating were investigated.The new stir bar was applied successfully in stir bar sorptive extraction with liquid desorption followed by liquid chromatography–mass spectrometry in tandem with a triple quadrupole for the determination of a group of polar pharmaceuticals and personal care products (PPCPs) in environmental water matrices. Different variables affecting extraction and desorption such as agitation speed, temperature, ionic strength and extraction time were optimised. The results showed that the stir bar is able to enrich the selected analytes effectively.The developed method was applied to determine a group of PPCPs in different complex environmental samples, including river, effluent and influent waste water.     

Optimisation of stir bar sorptive extraction applied to the determination of volatile compounds in vinegars

Stir bar sorptive extraction (SBSE) was evaluated for analysing volatile compounds in vinegar. The extraction and desorption analytical conditions have been optimised using a two-level factorial design expanded further to a central composite design. This chemometric tool is very appropriate in screening experiments where the aim is to investigate several possibly influential and/or interacting factors. For the extraction step, the optimum analytical conditions were: sample volume 25 ml without dilution, sampling time 120 min, NaCl content 5.85 g, and stirring speed 1250 rpm. For the desorption step, the optimised analytical conditions were: desorption temperature 300 degrees C, cryofocusing temperature -140 degrees C, flow of helium 75 ml min(-1), and desorption time 10 min. The SBSE procedure developed shows detection limits, and linear ranges adequate for analysing this type of compounds. The repeatability values obtained were lower than 10%. SBSE is a very simple, solvent-free, fast technique with better sensitivities, in general, than SPME. However, a disadvantage of this technique is that, up to now, the stir bar offers a limited enrichment capability for polar compounds because is only available with PDMS coating.     

Recent developments in stir bar sorptive extraction

As a crucial step in qualitative and quantitative analysis, sample pretreatment is commonly used to isolate the target analytes, concentrate them, or convert them into the forms tailored to the instrumental analysis. In recent years, there has been a trend for sample pretreatment techniques to become more miniaturized and more environmentally friendly. Stir bar sorptive extraction (SBSE), which was developed in 1999, is such an environmentally friendly microextraction technique. Compared with other microextraction techniques, including solid phase microextraction and liquid phase microextraction, SBSE provides a higher extraction efficiency and better reproducibility owing to the much greater amount of the extraction phase, and no special skills are required. However, there are some problems associated with SBSE, such as the limited applicable coatings, coating abrasion of the laboratory-made stir bar, and the difficulty in automation, which restrict the further improvement and application of SBSE. This review focuses on the development of SBSE in the past decade, in terms of coating preparation, automated systems, novel extraction modes, its use with various instruments, and applications in food, environmental, and biological samples.

Solid-phase extraction of polar compounds with a hydrophilic copolymeric sorbent

A new synthesized copolymer based on N-vinylimidazole-divinylbenzene (VIm-DVB) was tested as a sorbent for the solid-phase extraction (SPE) of polar analytes. In the on-line SPE, this synthesized sorbent enabled 100 ml of sample to be preconcentrated with recoveries as high as 80% for oxamyl, phenol (Ph) and derivates, bentazone and (4-chloro-2-methylphenoxy)acetic acid (MCPA). For the off-line SPE, 1000 ml of sample was extracted and recoveries were higher than 92% for all compounds with the exception of oxamyl (83%) and methomyl (78%). The VIm-DVB sorbent gives better recoveries than the previously synthesized 4-vinylpyridine-divinylbenzene (VP-DVB) resin and similar to such highly crosslinked commercial sorbents as LiChrolut EN or Oasis HLB. Real water samples were used to validate the on-line SPE method. Linearity was good and detection limits were between 0.1 and 0.2 microg l(-1).     

Solid-phase dynamic extraction for the enrichment of polar volatile organic compounds from water

Headspace solid-phase dynamic extraction coupled to gas chromatography-mass spectrometry (HS-SPDE-GC/MS) was evaluated for the trace determination of polar volatile organic compounds (PVOC) from aqueous matrices. The target compounds included 3 ethers and 12 alcohols. Four SPDE needle coatings with different phase polarities and sorption properties (WAX, 1701, PDMS, PDMS/AC) were tested. The effects of extraction temperature, number of extraction cycles, and ionic strength on partitioning of the target compounds have been investigated in detail, including the determination of salting-out constants for the investigated compounds. Lowest method detection limits (MDLs) were obtained with the WAX and the PDMS/AC phase. The WAX phase showed MDLs for ethers in the range of 0.06 microg/L (MTBE) to 0.8 microg/L (1,4-dioxane) and for alcohols between 0.02 microg/L (3-methyl-1-pentanol) and 3.5 microg/L (1-propanol). The evaluated MDLs for ethers with the PDMS/AC were in the range 0.06 microg/L (MTBE) to 1.2 microg/L (1,4-dioxane) and for alcohols between 0.004 microg/L (1-hexanol) and 4.9 microg/L (ethanol). Using either of these two phases, SPDE provides comparable or better sensitivities for the investigated compounds than other enrichment techniques, high sample throughput because of full automation, and short extraction times as well as a high robustness of the extraction phase because of its protection inside the steel needle. SPDE applicability has been demonstrated for the determination of fusel oils in different alcoholic beverages.