Bi_(0.5)Na_(0.5)TiO_3的制备及光催化性能研究

以Bi(NO3)3·5H2O、Na OH、Ti(OC4H9)4为原料,采用水热法制备Bi0.5Na0.5Ti O3纳米光催化剂。用XRD、TEM表征了Bi0.5Na0.5Ti O3光催化剂的结构和形貌。以亚甲基蓝为模型污染物,考察了不同浓度的Na OH对Bi0.5Na0.5Ti O3晶体在紫外光和可见光照射下光催化活性的影响。通过荧光技术研究了Bi0.5Na0.5Ti O3光催化剂表面羟基自由基的生成,探究了清除剂对光催化降解污染物活性的影响。结果表明:Na OH的浓度对Bi0.5Na0.5Ti O3光催化剂的紫外光和可见光活性有很大的影响,当Na OH浓度为8mol·L-1时制备的Bi0.5Na0.5Ti O3晶体光催化活性最高,光照1h,亚甲基蓝的紫外及可见光催化降解率分别达到69.8%、53.4%,在光催化降解过程中·O2ˉ和·OH起主要作用,尤其是·O2-起了重要作用。     

稀土离子Tm3+掺杂Bi2WO6的可见光催化性能

以Na_2WO_4·2H_2O和Bi(NO_3)_3·5H_2O为主要原料,采用水热法合成了稀土离子Tm~(3+)掺杂的Bi_2WO_6光催化剂。采用XRD、SEM、TEM、Raman、PL、DRS研究了Tm~(3+)掺杂Bi_2WO_6的物相,微观形貌和可见光催化性能。结果表明,Tm~(3+)掺杂有效提高了Bi_2WO_6的光催化性能,当掺杂量为6%时,样品的光催化性能最好,可见光照射30 min后,对罗丹明B的降解效率达到91.27%,而可见光照射5 h后,对焦糖色素的降解效率达45.25%。与未掺杂Bi_2WO_6相比,分别提高了27.78%和35.22%。     

Bi2Ti2O7/TiO2复合纤维：原位水热合成及光催化性能

采用静电纺丝技术制备的TiO2纤维作为模板和反应物,通过原位水热合成了具有异质结构的Bi2Ti2O7/TiO2复合纤维。利用X射线衍射(XRD)、扫描电镜(SEM)、能量散射光谱(EDS)、高分辨透射电镜(HRTEM)和紫外可见吸收光谱(UV-Vis)等分析测试手段对样品的结构和形貌进行表征。以罗丹明B为模拟有机污染物进行光催化降解实验。结果表明:花状Bi2Ti2O7纳米结构均匀地生长在TiO2纤维上,制备了Bi2Ti2O7与TiO2相复合的光催化材料,其光谱响应范围拓宽至可见光区,与纯TiO2纤维相比可见光催化活性显著提高,且易于分离、回收和循环使用。初步探讨了Bi2Ti2O7/TiO2异质结的生长机制和光催化活性提高机理。     

BiVO_4/Bi_6O_6(OH)_3(NO_3)_3复合光催化剂的制备及光催化性能研究

以Bi(NO_3)_3·5H_2O和NH_4VO_3为原料,控制水溶液介质p H及反应时间,采用水热合成法制备钒酸铋(BiVO_4)及其复合物(BiVO_4/Bi_6O_6(OH)_3(NO_3)_3).利用X-射线粉末衍射、扫描电子显微镜和紫外-可见漫反射吸收光谱等手段对制备的样品进行了物理表征,结果表明,在控制反应时间为1 h,介质p H值在1.14~9.01之间时,制备的样品为BiVO_4/Bi_6O_6(OH)_3(NO_3)_3复合物,当p H值增加至10.92时为纯BiVO_4;控制介质p H为7.17,反应时间在1~12 h之间时得到BiVO_4/Bi_6O_6(OH)_3(NO_3)_3复合光催化剂,反应时间为18 h时为纯BiVO_4.在可见光(λ≥400 nm)照射下,以有机染料罗丹明B(Rhodamine B,Rh B)为底物,研究不同条件制备的BiVO_4或者复合物为光催化剂的光催化特性,发现p H=7.17,水热反应12 h得到的催化剂(BiVO_4/Bi_6O_6(OH)_3(NO_3)_3)光催化降解活性高于对照制备的纯BiVO_4.同时在可见光照射下,BiVO_4/Bi_6O_6(OH)_3(NO_3)_3亦可以有效降解无色小分子2,4-二氯苯酚(2,4-Dichlorophenol,2,4-DCP),说明氧化过程涉及到光催化过程.分析BiVO_4/Bi_6O_6(OH)_3(NO_3)_3复合光催化剂对Rh B光催化降解过程中活性物种,表明在降解过程中主要涉及空穴和超氧氧化,O_2·~-起主要作用.     

Bi_2MoO_6/BiVO_4异质结的水热合成和可见光催化活性(英文)

采用一步水热法制备Bi2MoO6/BiVO4复合光催化剂.利用X射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、高分辨透射电子显微镜(HRTEM)等手段对其晶体结构和微观结构进行了表征.结果表明,Bi2MoO6纳米粒子沉积在BiVO4纳米片表面从而形成异质结结构.紫外-可见漫反射光谱(UV-Vis DRS)表明所制备的Bi2MoO6/BiVO4异质结较纯相Bi2MoO6和BiVO4对可见光吸收更强.由于形成异质结结构及其光吸收性能使Bi2MoO6/BiVO4光催化活性有较大提高.可见光下(λ420 nm)光催化降解罗丹明B(RhB)实验结果表明,Bi2MoO6/BiVO4光催化活性较纯相Bi2MoO6和BiVO4高.Bi2MoO6/BiVO4样品光催化性能提高的原因是Bi2MoO6和BiVO4形成异质结,从而有效抑制光生电子-空穴对的复合,增大了可见光吸收范围及比表面积.     

圆盘状Bi2WO6-BiPO4异质结的水热合成及光催化性能

采用水热法制备Bi2WO6-BiPO4异质结光催化剂．利用模拟太阳光照射下的罗丹明B降解实验评价了Bi2WO6-BiPO4复合物的光催化性能．结果表明,Bi2WO6-BiPO4光催化活性比Bi2WO6和BiPO4高得多．当Bi2WO6与BiPO4的摩尔比为1：1时复合光催化剂对罗丹明B的降解率最高．Bi2WO6-BiPO4催化活性增强主要归结为两者之间形成了有效的异质结结构,其内建电场能够促进光生载流子的分离．同时,Bi2WO6的加入增强了其对可见光的吸收．研究表明O2^· -和h^＋在光催化降解过程中是主要的活性物种.     

pH值对Bi2MoO6晶体形貌和可见光催化性能的影响

以(NH₄)₆Mo₇O₂₄·4H₂O和Bi(NO₃)₃·5H₂O为原料,采用普通水热法制备Bi₂MoO₆光催化剂,研究pH值对制备该光催化剂的影响.对所制备的系列样品,采用X-射线衍射仪(XRD)、扫描电子显微镜(SEM)、比表面积分析仪、X射线光电子能谱仪(XPS)和紫外-可见漫反射(UV-Vis DRS)进行表征.结果表明:pH值对Bi₂MoO₆晶体的物相组成、形貌和光催化性能均有显著影响.pH值为1~7时,所制备的样品为纯相Bi₂MoO₆,pH值为9或11时,出现第二相Bi_3.64Mo_0.36O_6.55;随着pH值的升高,形貌依次为纳米棒、纳米片和无规则纳米颗粒.在可见光(λ≥420 nm)照射下,通过光催化降解罗丹明B(Rhodamine B,RhB),探讨了制备Bi₂MoO₆的pH值对其可见光催化活性的影响.当pH=7时,制备的样品光催化效果最好,光照50 min后对初始浓度为5 mg·L^-1的罗丹明B溶液的降解率为85%.     

Ce掺杂Bi2MoO6/TiO2纳米纤维异质结的制备及可见光催化性能

以静电纺丝技术制备的TiO_2纳米纤维为基质,通过溶剂热法制备了异质结型稀土Ce掺杂Bi_2MoO_6/TiO_2复合纳米纤维。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)、透射电镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)以及荧光光谱(PL)等分析测试手段对样品的物相、形貌和光学性能等进行表征。以罗丹明B为模拟有机污染物,研究了样品的可见光催化性能。结果表明:在稀土掺杂样品中,Ce离子进入Bi_2MoO_6晶格,部分取代Bi3+,导致晶胞膨胀,晶格畸变,形成缺陷;与TiO_2复合形成异质结,有利于光生电荷的产生、转移和有效分离,从而提高TiO_2纳米纤维的光催化活性。可见光照射180 min,罗丹明B的降解率达到95.1%。经5次循环光催化降解活性基本不变,样品具有良好的光催化稳定性。     

Bi/TiO_2复合纳米纤维制备及可见光催化性能

以电纺TiO_2纳米纤维为基质,EDTA为鳌合剂和吸附剂,采用溶剂热法制备Bi/TiO_2复合纳米纤维光催化材料,利用X射线粉末衍射(XRD)、扫描电镜(SEM)、X射线能量色散谱(EDS)、透射电镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)和荧光光谱(PL)等分析测试手段对样品的物相、形貌和光学性能等进行表征,以罗丹明B(Rh B)为模拟有机污染物,考察了样品的光催化性能。结果表明:EDTA在复合纳米纤维的合成过程中起到关键作用,通过改变EDTA的用量可以有效控制纤维表面构筑单质Bi纳米球的大小和覆盖密度。所制备的复合纳米纤维具有良好的可见光催化活性和稳定性,当单质Bi的负载量为65%时光催化活性最强,可见光照射180 min,RhB的降解率达到96.40%,循环使用5次降解率仍保持在91%以上。     

Ｂｉ（ Ｎｂ） ＯＣｌ 光 催 化 剂 的 制 备 及 其 可 见 光 降 解罗 丹 明 Ｂ 溶 液 的 性 能

半导体光催化剂作为环境净化材料,具有稳定性好、光效率高、无二次污染等特点,具有广泛的应用前景.过去的研究大都集中在以TiO2为基础的光催化剂上.本文制备了具有层状结构的Bi基氧氯化物Bi(Nb)OCl光催化剂,用XRD、BET和UV-VIS吸收对样品进行了晶相、孔结构和光吸收性能表征,用罗丹明B的降解表征了材料的光催化活性.结果表明,BiOCl和Bi4NbO8Cl均具有可见光光催化降解活性,但两者的反应机理不同,Bi4NbO8Cl是光催化机制,BiOCl是染料光敏化机制.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Preparation and structure of NaSr0.5Al2B2O7 and NaCa0.5Al2B2O7

Two compounds NaSr_0.5Al₂B₂O₇ and NaCa_0.5Al₂B₂O₇, have been found to crystallize into a new structure type by Rietveld refinement from X-ray powder diffraction data. Their structure belongs to hexagonal space group P6₃/m, with lattice parameters of , for NaSr_0.5Al₂B₂O₇ and , for NaCa_0.5Al₂B₂O₇, respectively. The structure is built up by [Al₂B₂O₇]²⁻ double layer and Na⁺/Ca²⁺ or Na⁺/Sr²⁺ ions alternatively stacking along the c-axis. The sites in the inter-double layer are fully occupied jointly by Na and Ca or Sr, but the intra-double layer sites are only half occupied solely by Na. A mechanism of the transition of the structure from CaAl₂B₂O₇ to present structure type by replacing only 1% Ca by Na (2%) as observed by Chang and Keszler (Mater. Res. Bull. 33 (1998) 299) is also proposed.     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Synthesis and characterization of quaternary selenides Sn2Pb5Bi4Se13 and Sn8.65Pb0.35Bi4Se15

Quaternary selenides Sn₂Pb₅Bi₄Se₁₃ and Sn_8.65Pb_0.35Bi₄Se₁₅ were synthesized from the elements in sealed silica tubes; their crystal structures were determined by single-crystal and powder X-ray diffraction. Both compounds crystallize in monoclinic space group C2/m (No.12), with lattice parameters of Sn₂Pb₅Bi₄Se₁₃: a = 14.001(6) Å, b = 4.234(2) Å, c = 23.471(8) Å, V = 1376.2(1) Å³, R₁/wR₂ = 0.0584/0.1477, and GOF = 1.023; Sn_8.65Pb_0.35Bi₄Se₁₅: a = 13.872(3) Å, b = 4.2021(8) (4) Å, c = 26.855(5) Å, V = 1557.1(5) Å³, R₁/wR₂ = 0.0506/0.1227, and GOF = 1.425. These compounds exhibit tropochemical cell-twinning of NaCl-type structures with lillianite homologous series L(4, 5) and L(4, 7) for Sn₂Pb₅Bi₄Se₁₃ and Sn_8.65Pb_0.35Bi₄Se₁₅, respectively. Measurements of electrical conductivity indicate that these materials are semiconductors with narrow band gaps; Sn₂Pb₅Bi₄Se₁₃ is n-type, whereas Sn_8.65Pb_0.35Bi₄Se₁₅ is a p-type semiconductor with Seebeck coefficients −80(5) and 178(7) μV/K at 300 K, respectively.     

Structural chemistry of Sr3Cr2WO9, Ca3Cr2WO9, and Ba3Cr2WO9

We have studied the preparation and crystallographic structure of three perovskite-type compounds: Sr₃Cr₂WO₉, cubic, the lattice parameter of which is a = 7.812Å; Ca₃Cr₂WO₉, tetragonal, the lattice parameters of which are a = 5.408 Å and c = 7.635Å; and Ba₃Cr₂WO₉, hexagonal, the lattice parameters of which are a = 5.691 Å and c = 13.957Å. We have compared these three structures and shown the relationship between the dimensions of the alkaline-earth metal and the existence of the different structures.