镍锌铁氧体/膨胀石墨/聚苯胺复合物的电磁损耗性能

用化学共沉淀法和原位乳液聚合法分别制备了镍锌铁氧体(Ni_xZn_1-xFe₂O₄)、Ni_0.7Zn_0.3Fe₂O₄/膨胀石墨(NZF/EG)二元复合物及其聚苯胺(PANI)包覆的三元复合物(NZF/EG/PANI)。用现代测试技术表征了样品的组成、结构、形貌和电磁性能。结果表明,NZF粒子较好地嵌入到EG的层间,PANI对NZF/EG的包覆效果良好;三元复合物的磁性能随磁性组分含量的减小而减弱,而电导率与EG和PANI的导电性及其相对含量相关联;复合物的电磁损耗性能优良,其中三元复合物优于二元复合物。含PANI 70wt%的NZF/EG/PANI三元复合物,制样厚度分别为1.5、2.0和2.5 mm时,其反射损耗峰值(有效带宽)分别为-19.99 dB(5.82 GHz),-20.33 dB (4.08 GHz)和-25.28 dB(3.67 GHz),具有优良的电磁波吸收效果。     

聚苯胺/聚丙烯酰胺/镍锌铜铁氧体复合物的制备及电磁性能

采用溶液聚合法制备了聚苯胺/聚丙烯酰胺/镍锌铜铁氧体(PANI/PAM/Zn0.4Ni0.5Cu0.1Fe2O4)三元复合物. 利用X射线衍射仪、红外光谱仪、扫描电子显微镜和振动样品磁强计分别表征了样品的结构、形貌和磁性能, 用阻抗/材料分析仪测定了复合物在1 MHz～1 GHz的频率范围内的磁损耗和介电损耗, 并研究了聚苯胺和引发剂的相对含量对复合物的磁损耗和介电损耗的影响. 结果表明复合物中磁性粒子和聚合物之间具有一定的相互作用, 复合物在1 MHz～1 GHz的频率范围内具有较大电磁损耗能力.     

Zn-Ni-Cu铁氧体/聚邻甲氧基苯胺复合物的制备及电磁性能

用共沉淀法和溶液原位聚合法分别制备了锌镍铜铁氧体粉末(ZNCF)及其聚邻甲氧基苯胺(POMA)复合物.用粉末X-射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、振动样品磁强计(VSM)等分别表征了产物的结构、形貌、电磁性能.结果表明,ZNCF/POMA复合物的组分之间存在一定的相互作用;POMA对ZNCF粒子的包覆能起到调控样品电磁性能的作用,复合物的磁性能随POMA含量的增加而减小,而电导率则相反;与单一组分相比,POMA/ZNCF复合物表现出更优良的电磁波吸收性能,ωZNCF为20%的复合物的反射损耗峰值和有效带宽分别为-27.32 dB和8.81 GHz,峰值对应的共振频率为11.61 GHz,是颇具应用前景的电磁波吸收材料.     

CoFe2O4及其膨胀石墨复合物的制备与电磁性能

通过超声-共沉淀技术合成了CoFe₂O₄(CF)及CoFe₂O₄/膨胀石墨复合物(CF/EG), 并表征了样品的微观结构、形貌、热稳定性和电磁性能.结果表明, CF的磁性能受沉淀剂类型和烧结温度等因素的影响, CF/EG复合物具有良好的导电性、磁性和电磁波吸收性能.EG与CF质量比为0.8的CF/EG复合物和石蜡制成的2.0 mm涂层(质量比1:2)在13.52 GHz处的最小反射损耗为-16.08 dB, 有效带宽达6.6 GHz, 在10~18 GHz频段表现出良好的电磁波吸收性能.复合物的吸波性能主要来自于膨胀石墨的电导损耗和介电损耗、钴铁氧体的磁损耗、组分间的界面弛豫作用及协同效应.     

膨胀石墨/聚苯胺/Fe_3O_4复合材料的制备及吸波性能

采用原位聚合方法制备了膨胀石墨/聚苯胺(EG/PANI)复合材料,将Fe_3O_4负载于EG/PANI表面,得到具有电磁吸收性能的EG/PANI/Fe_3O_4复合材料.通过扫描电子显微镜(SEM)、X射线衍射仪(XRD)、傅里叶变换红外光谱仪(FTIR)及矢量网络分析仪(VNA)等对复合材料的形貌、成分和吸波性能进行了研究.吸波性能分析结果表明,当掺杂浓度为0.05 mol/L,匹配厚度d=2 mm时,样品的最小反射损耗(RLmin)在8.64 GHz处达到-37 dB.随着掺杂浓度的增加,最小反射损耗峰向低频移动,对应的匹配厚度逐渐变厚.材料的介电弛豫极化、涡流损耗及λ/4模型的干涉相消现象出现的双峰,使EG/PANI/Fe_3O_4复合材料在电磁波吸收领域有一定的应用前景.     

Fe_3O_4@聚吡咯@聚苯胺核壳结构的制备及吸波性能

用聚吡咯(PPy)对溶剂热法制备的Fe_3O_4纳米颗粒进行表面修饰,再用聚苯胺(PANI)调控Fe_3O_4@PPy复合材料的电磁组成,制备出具有核壳结构的Fe_3O_4@PPy@PANI复合吸波材料.当PPy对Fe_3O_4纳米颗粒修饰后,PANI极易包覆在纳米颗粒表面.电磁性能分析结果表明,当苯胺(An)与Fe_3O_4@PPy质量比为1/4时,最小反射损耗值(RLmin)达到-39.2 d B;当An与Fe_3O_4@PPy的质量比为1/2时,反射损耗小于-10d B的频宽达到4.6 GHz.电磁成分比例对复合材料的吸波性能有较大的影响,随着聚苯胺含量的增加,电磁吸收呈现先增加后减小的趋势.     

配位-氧化聚合-水热法制备聚苯胺/CoFe_2O_4纳米复合物及其微波吸收性能

采用"配位-氧化聚合-水热法"制备了本征态聚苯胺/CoFe2O4二元纳米复合物,再以磺基水杨酸掺杂获得聚苯胺/CoFe2O4电磁复合物.考察了反应物配比及掺杂酸浓度对产物电磁性能的影响.通过透射电子显微镜(TEM)、X射线衍射(XRD)、红外光谱(FTIR)及电磁测量等手段对聚苯胺/CoFe2O4的形貌、结构及性能进行了表征.结果表明,复合物呈现多级结构,其中CoFe2O4为立方体状,平均粒径小于20 nm.当CoFe2O4的质量分数为8.86%时,复合物的电导率约为0.43 S/cm;当聚苯胺/CoFe2O4复合物厚度为2 mm时,在16.01 GHz处最大反射损耗为-16.71 dB,小于-10 dB的带宽达4.68 GHz;而当聚苯胺/CoFe2O4复合物厚度为3.2 mm时,在9.23 GHz处最大反射损耗达-51.81 dB,小于-10 dB的带宽为3.69 GHz,表明具有良好的吸波性能.     

兼具电磁性能的PANI/ZnFe2O4纳米复合材料的制备

运用改进的溶胶凝胶-原位聚合法制备出了兼具电、磁性能的PANI/ZnFe2O4纳米复合材料,借助TEM、XRD、FTIR、四探针电导率仪和VSM(振动样品磁强计)等技术研究了复合材料的结构及其电磁性能。结果表明,通过该法可以实现ZnFe2O4与PANI的有机复合,制得纳米尺寸的、ZnFe2O4与PANI相间以化学键结合的纳米复合材料;复合材料兼具电、磁性能,其导电率随ZnFe2O4含量增加而降低,饱和磁化强度随之而升高,复合物的矫顽力在所研究的含量范围内均较纯ZnFe2O4大,且随ZnFe2O4含量的增加呈先升高后降低的变化趋势。此外,对ZnFe2O4进行HNO3预处理可以有效改善复合材料的电磁性能。     

导电聚苯胺与磁性CoFe2O4纳米复合物的合成及其电磁性能

在利用HNO3处理CoFe2O4磁性纳米粒子使其表面离子化、分散性得到改善的基础上,采用苯胺在其表面原位聚合,制备了具有电磁功能的聚苯胺(PANI)/CoFe2O4纳米复合物.借助TEM、XRD、FT-IR、四探针电导率仪和VSM(振动样品磁强计)等分析手段研究了复合物的形貌、结构及其电磁性能.结果表明,CoFe2O4以25 nm左右的粒子分散于聚苯胺基体中,被其完全包覆,CoFe2O4与PANI之间存在化学键合作用;复合物同时具有电性能和磁性能,其导电牢随CoFe2O4含量增加而降低,饱和磁化强度随之升高,而矫顽力在所研究的范围内则先增大而后又减小,且均高于CoFe2O4的矫顽力.     

导电聚苯胺与磁性CoFe2O4纳米复合物的合成及其电磁性能

在利用HNO3处理CoFe2O4磁性纳米粒子使其表面离子化、分散性得到改善的基础上, 采用苯胺在其表面原位聚合, 制备了具有电磁功能的聚苯胺(PANI)/CoFe2O4纳米复合物. 借助TEM、XRD、FT-IR、四探针电导率仪和VSM(振动样品磁强计)等分析手段研究了复合物的形貌、结构及其电磁性能. 结果表明, CoFe2O4以25 nm左右的粒子分散于聚苯胺基体中, 被其完全包覆, CoFe2O4与PANI之间存在化学键合作用; 复合物同时具有电性能和磁性能, 其导电率随CoFe2O4含量增加而降低, 饱和磁化强度随之升高, 而矫顽力在所研究的范围内则先增大而后又减小, 且均高于CoFe2O4的矫顽力.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.