Evaluation of continuous hydride generation combined with helium and argon microwave induced plasmas using a surfatron for atomic emission spectrometric determination of arsenic,antimony and selenium

The direct coupling of continuous hydride generation with both Ar and He microwave induced plasmas (MIP) sustained in a surfatron has been optimized for the simultaneous determination of arsenic, antimony and selenium with atomic emission spectrometry. While a discharge tube of quartz was found suitable for the Ar plasma, the use of an Al₂O₃ tube led to improved performance of the He plasma. The He MIP was found to be less tolerant to the introduction of hydrogen than the Ar MIP, and correspondingly the hydride generation should be operated at a lower flow rate of 0.5% NaBH₄ solution. The introduction of the H₂O vapour produced during hydride generation into both discharges was found to greatly decrease the sensitivities and to degrade the measurement precision. It could be effectively removed with trapping by concentrated H₂SO₄. The detection limits (3σ) for As, Sb and Se are 1, 0.4 and 1 ng ml⁻¹ with the Ar MIP, and 2, 0.3 and 6 ng ml⁻¹ with the He MIP, respectively. The calibration curves are linear over three decades of concentration. The mutual interferences from As(III), Sb(III), Se(IV), Bi(III) and Sn(IV) were found to be negligible at interferent concentrations below 1 μg ml⁻¹ and in most cases the tolerable interferent concentrations are up to 20 μg ml⁻¹. The proposed method has been applied to the determination of As, Sb and Se in tea samples at μg g⁻¹ levels.     

Measurements of rubidium in standard reference samples by wavelength-modulation diode laser absorption spectrometry in a graphite furnace

An investigation of the capabilities of the WM-LDAS-GF (wavelength-modulation laser diode absorption spectrometry in graphite furnaces) technique for detection of Rb at low pg ml⁻¹ concentrations in samples with complex matrices has been performed. Five reference materials were investigated with respect to their Rb content by the WM-LDAS-GF technique: corn bran (NIST 8433); NIST water; (1643d) riverine water (SLRS-2); estuarine water (SLEW-1); and sea water (NASS-3). Freeze-dried corn bran was found to have a Rb concentration of 440 ± 70 ng g⁻¹. This compares well with the certified concentration of 500 ± 300 ng g⁻¹. The Rb content of the NIST water was assessed to 12.7 ± 1.7 ng ml⁻¹. This compares excellently with the specified (although not certified) level of 13 ng ml⁻¹. None of the three other reference materials has any certified Rb level. The Rb content of riverine water was found to be 3.4 ± 0.8 ng ml⁻¹. Chemical interferences were encountered when estuarine water and sea water were analyzed (loss of Rb as RbCl). Addition of NH₄NO₃ as the matrix modifier increased the Rb recovery values considerably (although not fully to unity). Estuarine water and sea water were found to have Rb contents of 30 ± 10 ng ml⁻¹ and 140 ± 50 ng ml⁻¹, respectively. A detection limit for Rb in deionized water of 10 fg (corresponding to a concentration of 1 pg ml⁻¹ using a 10 μL aliquot) was obtained. This is identical to (and thus verifies) the previously published result by the group of K. Niemax. These results show that the WM-LDAS-GF technique is capable of detecting traces of Rb in samples also with complex matrices.     

Evaluation of tungsten–rhodium coating on an integrated platform as a permanent chemical modifier for cadmium,lead, and selenium determination by electrothermal atomic absorption spectrometry

A tungsten–rhodium coating on the integrated platform of a transversely heated graphite atomizer is proposed as a permanent chemical modifier for the determination of Cd, Pb, and Se by electrothermal atomic absorption spectrometry. It was demonstrated that coating with 250 μg W+200 μg Rh is as efficient as the conventional Mg(NO₃)₂+NH₄H₂PO₄ or Pd+Mg(NO₃)₂ modifiers for avoiding most serious interferences. The permanent W–Rh modifier remains stable for 300–350 firings of the furnace, and increases tube lifetime by 50%–100% when compared to pyrolytic carbon integrated platforms. Also, there is less degradation of sensitivity during the atomizer lifetime when compared with the conventional modifiers, resulting in a decreased need of re-calibration during routine analysis. The characteristic masses and detection limits achieved using the permanent modifier were respectively: Cd 1.1±0.4 pg and 0.020 μgL⁻¹; Pb 30±3 pg and 0.58 μgL⁻¹ and Se 42±5 pg and 0.64μgL⁻¹. Results from the determination of these elements in water reference materials were in agreement with the certified values, since no statistical differences were found by the paired t-test at the 95% level.     

Multiple microflame quartz tube atomizer — further development towards the ideal hydride atomizer for atomic absorption spectrometry

The development of an improved type of hydride atomizer for atomic absorption spectrometry — multiple microflame quartz tube atomizer (MMQTA) — is presented. The main feature of this atomizer is recurrent analyte atomization proceeding over its whole optical tube length, which is achieved by production of H-radicals at multiple points within the tube by oxygen microflames burning in the hydrogen-containing atmosphere. The MMQTA design optimization leading to a complete filling of the observation volume with H-radicals is described. The influence of individual atomization parameters is discussed. Optimum H-radical producing oxygen intake into the MMQTA was found to correspond to a H₂:O₂ stoichiometric (3:1) ratio. The performance of the individual MMQTA tube designs is evaluated and compared to a typical externally heated quartz tube atomizer (EHQTA) — the linearity of calibration graphs for As, Se and Sb is significantly improved in all MMQTA tubes, without compromising the sensitivity, simplicity, low cost and easy operation. In fact, the free atom reactions within the tube causing calibration curvature are avoided up to an analyte concentration of at least 200 ng ml⁻¹ for Se and Sb and 100 ng ml⁻¹ for As. Tolerance limits of 0.7, 1.4, 0.2 and 0.2 μg ml⁻¹ are achieved for the atomization interferences of As on Se, Se on As, Sb on Se and Se on Sb, respectively, which is an improvement by 1–2 orders of magnitude in comparison to the conventional EHQTA with the same hydride generation system.     

Determination of arsenic in glycerine by flow injection,hydride generation and inductively-coupled plasma/atomic emission spectrometry

The determination of low concentrations of arsenic in glycerine is investigated with flow injection for the introduction of analyte and tetrahydroborate reagent for arsine generation, separation in a vapor-liquid flow cell, and inductively-coupled plasma/atomic emission spectrometry (i.c.p./a.e.s.). Peak areas are used to quantify arsenic in the concentration range 0.12–3.0 μg ml^?1. Peak areas for prepared standards exhibited average deviations of about 1.4% for this concentration range. The slope and intercept for a least- squares fit of area (nanocoulombs) vs. concentration (μg ml^?1) were 10.9 ± 0.17 and 0.46 ± 0.3, respectively.     

Internal standardization in graphite furnace atomic absorption spectrometry: Comparative use of As and Ge to minimize matrix effects on Se determination in milk

Arsenic and germanium have been evaluated as internal standards to minimize matrix effects on the direct determination of selenium in milk by graphite furnace atomic absorption spectrometry (GFAAS) using tubes with integrated platform, pre-treated with W together with Pd as chemical modifier. The efficiency of As and Ge as internal standards for 25 μg L^− 1 Se plus 500 μg L^− 1 As or Ge in diluted (1 + 9 v/v) milk plus 1.0% (v/v) HNO₃ was evaluated by means of correlation graphs plotted from the normalized absorbance signals (n = 20) of internal standard (axis y) versus analyte (axis x). The equations that describe the linear regression were: A^As = − 0.004 ± 0.019 + 1.02 ± 0.019 A^Se (r = 0.9967 ± 0.005); A^Ge = − 0.017 ± 0.015 + 1.01 ± 0.015 A^Se (r = 0.9978 ± 0.004). Samples and reference solutions were automatically spiked with 500 μg L^− 1 Ge or As and 1.0% (v/v) HNO₃ by the autosampler. For 20 μL of aqueous standard solutions, analytical curves in the 5.00–40.0 μg L^− 1 Se range were established using the ratio of Se absorbance to internal standard absorbance (A^Se / A^IS) versus analyte concentration, and good linear correlations were obtained. The characteristic mass was 40 pg Se. Limits of detection were 0.55 and 0.40 μg L^− 1 with As and Ge as the internal standard, respectively. Relative standard deviations (RSD) for a sample containing 25 μg L^− 1 Se were 1.2% and 1.0% (n = 12) using As and Ge, respectively. The RSD without internal standardization was about 6%. The accuracy of the proposed method was evaluated by an addition-recovery experiment and all recovered values were in the 99–105% range with IS and in the 70–80% range without IS. Using Ge as the internal standard, results of analysis of standard reference materials were in agreement with certified values at a 95% confidence level. The selenium concentration for 10 analyzed milk samples varied from 5.0 to 20 μg L^− 1.     

Simultaneous determination of hydride forming elements (As, Sb, Se, Sn) and Hg in sonicate slurries of biological and environmental reference materials by hydride generation microwave induced plasma optical emission spectrometry (SS-HG-MIP-OES)

A slurry sampling hydride generation (SS-HG) method for the simultaneous determination of hydride forming elements (As, Sb, Se, Sn) and Hg, without total sample digestion, has been developed using batch mode generation system coupled with microwave induced plasma optical emission spectrometry (MIP-OES) from certified biological and environmental reference materials. Slurry concentration up to 3.6% m/v (particles < 80 μm) prepared in 10% HCl containing 100 μl of decanol, by the application of ultrasonic agitation, was used with calibration by the standard addition technique. Harsh conditions were used in the slurry preparation in order to reduce the hydride forming elements to their lower oxidation states, As(III), Sb(III), Se(IV) and Sn(II) and Hg, being reduced to mercury vapor, before reacting with sodium tetrahydroborate. An ultrasonic probe was used to homogenize the slurry in the quartz cup just before its introduction into the reaction vessel. For 10 ml of slurry sample, detection limits (LOD, 3σ_blank, peak area) of 0.06, 0.08, 0.15, 0.12 and 0.10 μg g^− 1 were obtained for As, Sb, Se, Sn and Hg, respectively. The method offers relatively good precision (RSD ranged from 9 to 12%) for slurry analysis. To test the accuracy, three certified reference materials were analyzed with the analyte concentrations mostly in the μg g^− 1 level. Measured concentrations are in satisfactory agreement with certified values for the biological reference materials: NRCC LUTS-1 (lobster hepatopancreas), NRCC DOLT-2 (Dogfish Liver) and environmental reference material: NRCC PACS-1 (Marine Sediment), all adequate for slurry sampling. The method requires small amounts of reagents and reduces contamination and losses.     

Vibrational spectra and normal coordinate calculations for trimethylselenonium-d0 and -d9 ions and dimethyl selenide-d0, -d6

The i.r. (4000-30 cm⁻¹) and Raman (4000-0 cm⁻¹) spectra of trimethylselenonium iodide and dimethyl selenide have been obtained, together with those of their deuterated analogues. All the active fundamentals of the trimethylselenonium ion have been assigned, assuming C_3ν molecular symmetry. Normal coordinate calculations have been carried out for the trimethyl-selenonium ion and dimethyl selenide and the SeC force constants of both the compounds are compared, including those of other corresponding chalcogenides.     

Application of a wall-stabilized argon plasma arc for the determination of some volatile hydride-forming elements

Volatile hydrides of As, Se, Sb and Sn, produced by a continuous manifold hydride generator, have been swept with argon and injected into the plasma of home-made direct current wall-stabilized argon plasma arc via one of its stabilizing segments. The arc burns in argon with an arc current of 20 A and a cathode-anode voltage of 40 V. Measurements were carried out using a 1 m focal length computer-controlled monochromator (Jobin Yvon 1000R) equipped with a holographic grating having 2400 grooves mm^− 1. Optimal values of the experimental variables that give the highest value of intensity ratio of line-to-background were determined. These are: plasma gas flow rate 1.0 l min^− 1, carrier gas flow rate 0.35 l min^− 1 for As and Sb and 0.6 l min^− 1 for Se and Sn, concentration of nitric acid used for acidification of the sample 2 M for As and Sb, 0.5 M for Se and 0.1 M for Sn and sodium borohydride concentration: 1.5% for As and Se and 2% for Sb and Sn. Chemical interference of some transition elements that affect the hydride generation process and a trial to mask their interference effect were investigated. Calibration curves were linear and limits of detection calculated on the base of 3σ of the background were found to be as low as 3.9, 6.8, 9.8 and 13.2 ng ml^− 1 for As, Se, Sb and Sn, respectively. Finally, the analytical applicability of the arc device was tested by the determination of As in four lake sediment samples, LKSD 1, LKSD 2, LKSD 3 and LKSD 4, of the Centre for Mineral and Energy Technology, Ottawa, Ontario, Canada, which have been analyzed for As using atomic absorption spectrometry (AAS). The results were in good agreement with those obtained by AAS.     

Preconcentration of analytes by aerosol deposition in Graphite Furnace Atomic Absorption Spectrometry at the pg ml−1 level

Different experimental configurations were considered, using an atomic absorption spectrometer, in order to obtain a suitable preconcentration of analyte inside the graphite furnace via aerosol deposition.The aim was to optimize the procedure in order to measure concentrations down to 1–5 pg ml⁻¹ in matrices with a low chemical content, such as snow or ice. At these concentration levels, the risk of contaminating the sample is one of the main problems to be considered when designing the aerosol deposition set-up. In addition, since the deposition time (t_dep) may be up to several tens of minutes, all the parameters which are decisive in controlling both deposition and atomization steps must be time independent and show good repeatability among measurements.With the procedure proposed in this paper it was found that the absorbance was linearly dependent on the product C_s·t_dep, where C, is the analyte concentration in the sample solution, down to the pg ml⁻¹ level. The regression parameters of the calibration curve were found to be reproducible for a period of weeks, indicating that the instrumental variables presented a high repeatability and, in particular, that the yield of atoms per unit mass in the sample was not influenced by the life-time of the graphite furnace (usually about 1000 firings).At a concentration of 3 pg ml⁻¹ of cadmium, the coefficient of variation of the absorbance (5 replicates) was found to be as low as 3 – 5%, when a 15 min deposition time was applied. At this concentration, the overall sample standard deviation, which depends on all the steps from sampling to analysis, remains the most significant figure of merit.     

Simultaneous determination of Se and As by hydride generation atomic absorption spectrometry with analyte concentration in a graphite furnace coated with zirconium

Conditions for the simultaneous determination of selenium and arsenic at ng l⁻¹ level were developed. Simultaneous determination of these elements was possible through the multielement capabilities of hydride generation, with in situ trapping and atomization in a graphite tube coated with zirconium and measurements using a dual channel atomic absorption spectrophotometer. The zirconium coating employed in this work was relatively stable; once formed it could stand ≈80 firings without any significant change in the efficiency of hydride collection. This appears to be an advantage over the palladium coating, which is usually formed individually before each measurement because of its thermal instability during the atomization step of the furnace temperature programme. As a result, two determinations of the two elements could be performed in 2.5 min. Under the optimized conditions, concentration detection limits of 17 and 13 ng l⁻¹ for a 7.1 ml sample volume were obtained for selenium and arsenic, respectively (absolute detection limits 120 and 92 pg for Se and As).     

Cyclic and stripping voltammetry of Se(+4) and Se(−2) at the HMDE in acidic media

Electroreduction of Se(+4) and electrooxidation of Se(?2) were studied at mercury electrodes in acidic media and an improved mechanism of the reduction process was proposed. This mechanism takes into account the fact that the reduction path is concentration-dependent. At lower concentrations of Se(+4), mercury selenide and hydrogen selenide are formed at various potentials. At higher Se(+4) concentrations the electrode quickly becomes covered by a rigid deposit of mercury selenide and then the reduction starts to proceed to elemental selenium. Another form of selenium was formed in the vicinity of the mercury surface due to a chemical reaction between H₂SeO₃ and H₂Se. Oxidation of hydrogen selenide proceeds similarly, in the sense that after coverage of the electrode surface by a deposit of mercury selenide the oxidation starts to proceed to elemental selenium. The cathodic stripping peak of mercury selenide can be obtained down to 2 × 10^?8M of Se(+4), but this peak is often split and therefore the determination of traces of Se(+4) by the cathodic stripping technique is cumbersome.     

In situ trapping of stibine in externally heated quartz tube atomizers for atomic absorption spectrometry

An evaluation of an extremely simple method for antimony preconcentration based on the novel experimental approach, in situ trapping of stibine in externally heated quartz tube atomizers, is presented. The only difference to the set-up employed for the conventional operation mode is that a flow of oxygen (at stoichiometric excess over hydrogen) is introduced just upstream of the atomizer in the trapping step of the procedure. The volatilization of the trapped analyte can be performed just by switching off the oxygen inlet. The collection/volatilization efficiency (± S.D.) is 100 ± 2%. For the collection time of 300 s (sample volume of 20 ml), the preconcentration ratio and detection limit (3σ), respectively, is 400 and 2.8 pg ml^− 1. A possible way of further improvement of the detection limit is suggested. The same approach can be analytically useful also for bismuthine (efficiency 55 ± 2%) but not for arsine, selenium hydride and tellurium hydride.     

Simultaneous determination of cadmium and lead in wine by electrothermal atomic absorption spectrometry

A method has been developed for the direct simultaneous determination of Cd and Pb in white and red wine by electrothermal atomic absorption spectrometry (ET-AAS) using a transversely heated graphite tube atomizer (THGA) with longitudinal Zeeman-effect background correction. The thermal behavior of both analytes during pyrolysis and atomization stages were investigated in 0.028 mol l⁻¹ HNO₃ and in 1+1 v/v diluted wine using mixtures of Pd(NO₃)₂+Mg(NO₃)₂ and NH₄H₂PO₄+Mg(NO₃)₂ as chemical modifiers. With 5 μg Pd+3 μg Mg as the modifiers and a two-step pyrolysis (10 s at 400°C and 10 s at 600°C), the formation of carbonaceous residues inside the atomizer was avoided. For 20 μl of sample (wine+0.056 mol l⁻¹ HNO₃, 1+1, v/v) dispensed into the graphite tube, analytical curves in the 0.10–1.0 μg l⁻¹ Cd and 5.0–50 μg l⁻¹ Pb ranges were established. The characteristic mass was approximately 0.6 pg for Cd and 33 pg for Pb, and the lifetime of the tube was approximately 400 firings. The limits of detection (LOD) based on integrated absorbance (0.03 μg l⁻¹ for Cd, 0.8 μg l⁻¹ for Pb) exceeded the requirements of Brazilian Food Regulations (decree #55871 from Health Department), which establish the maximum permissible level for Cd at 200 μg l⁻¹ and for Pb at 500 μg l⁻¹. The relative standard deviations (n=12) were typically <8% for Cd and <6% for Pb. The recoveries of Cd and Pb added to wine samples varied from 88 to 107% and 93 to 103%, respectively. The accuracy of the direct determination of Cd and Pb was checked for 10 table wines by comparing the results with those obtained for digested wine using single-element ET-AAS, which were in agreement at the 95% confidence level.     

Direct determination of arsenic in fresh and saline waters by electrothermal vaporization inductively coupled plasma mass spectrometry

A method is described for the direct determination of arsenic in fresh and saline waters by electrothermal vaporization inductively coupled plasma mass spectrometry. Arsenic could be determined directly in waters containing up to 10 000 μg ml⁻¹ NaCl without interference from the formation of ⁷⁵ArCl⁺. For non-saline waters, arsenic was determined directly with the addition to both aqueous calibration standards and samples of 0.1 μg each of Pd and Mg to act as physical carriers. For the analysis of highly saline waters, the use of Pd and Mg chemical modifier served to thermally stabilize arsenic up to a temperature of 1000°C, while the separate addition of 8 mg of ammonium nitrate was used to remove chloride from the sample. This eliminated serious spectral interference on ⁷⁵As⁺ from ⁷⁵ArCl⁺. Although the ArCl⁺ spectral interference was completely eliminated, residual Na co-volatilized with As caused signal suppression, requiring the use of the method of standard additions for calibration. An absolute limit of detection limit for As of 0.069 pg was obtained corresponding to 6.9 pg ml⁻¹ in a 10 μl sample.     

Electrofusion of protoplasts modified by protein adsorption

The synergistic influence of proteins at lowest concentrations (below mg ml⁻¹) on barley protoplast electrofusion together with dielectrophoresis for adhesion of protoplast membranes has been studied by determination of the relative electrofusion yield F_r, which allows further insight into `protein modified electroporation and electrofusion'. As a general rule all proteins with isoelectric points pI>8 stimulate fusion: F_r>1 in buffer free mannitol solution (pH 6.5) reaching levels at F_r=2∼3. Proteins with pI<8 show at lowest concentrations (<1 mg ml⁻¹) also a stimulating effect: F_r>1 followed by the inhibition of F_r—sometimes reaching zero—accompanied by rising conductivity with increasing concentrations. These results are important for resealing, insertion, transfection and the role of integral membrane proteins for the mechanism of fusion.     

Simultaneous determination of hydride forming (As, Bi, Ge, Sb, Se, Sn) and Hg and non-hydride forming (Ca, Fe, Mg, Mn, Zn) elements in sonicate slurries of analytical samples by microwave induced plasma optical emission spectrometry with dual-mode sample introduction system

A slurry sampling method for the simultaneous determination of hydride forming (As, Bi, Ge, Sb, Se, Sn) and Hg and non-hydride forming (Ca, Fe, Mg, Mn, Zn) elements, without total sample digestion has been developed using the commercial dual-mode sample introduction system (MSIS) coupled with microwave induced plasma optical emission spectrometry (MIP-OES) from biological and environmental reference materials and real samples. The main advantage of this system is its simultaneous determination of elements that form volatile vapor species and elements that do not, without any instrumental changes. Optimization of reaction, nebulization and instrumental conditions was performed to characterize the new system. Slurry concentration up to 4% m/v (particles < 100 μm) prepared in 10% HNO₃ containing 100 μL of decanol, by application of ultrasonic agitation, was used with calibration by the standard addition technique. An ultrasonic probe was used to homogenize the slurry in the quartz cup just before its introduction into the reaction/nebulization system; the multimode sample introduction system (MSIS) combines the benefits of nebulization and vapor generation in a single device. Detection limits (LOD, 3σ_blank, peak area) of 0.07, 0.29, 0.25, 0.10, 0.12, 0.14, 0.11, 0.28, 0.42, 0.02, 0.21 and 0.34 μg g^− 1 were obtained for As, Bi, Ge, Sb, Se, Sn, Hg, Ca, Fe, Mg, Mn and Zn, respectively. The relative standard deviations were ca. 10%, adequate for slurry analysis. To test the accuracy, six certified reference materials were analyzed with the analyte concentrations mostly in the μg g^− 1 level. Measured concentrations are in satisfactory agreement with certified values for the biological reference materials (LUTS-1, DOLT-2) and environmental reference materials (PACS-1, GWB 07302, NIST 2710, NBS 1633b), all adequate for slurry sampling. The method was successfully applied to the determination of the elements in real samples (coal fly ash, lake sediment, sewage). The method requires small amounts of reagents and reduces contamination and losses.     

Hydride generation-graphite furnace atomic absorption spectrometry: new prospects

Summary Methods are described for the interference free determination of As and Se in seawater as well as marine tissues and sediments based on the generation of AsH₃, and SeH₂ using NaBH₄ with subsequent trapping in a graphite furnace at 600° C. Calibration is achieved with simple aqueous working curves having sensitivities of 24±4 and 72±17 pg/0.0044 A for As and Se, respectively. Absolute detection limits of 30 pg As and 70 pg Se are estimated. Precision of determination is 2–3% for As and 5–10% for Se.

---

Graphitofen-AAS mit Hydriderzeugung: neue Entwicklungen

Zusammenfassung Verfahren werden beschrieben zur störungsfreien Bestimmung von As und Se in Meereswasser sowie marinen Geweben und Sedimenten, die auf der Erzeugung von AsH₃ und SeH₂ mit Hilfe von NaBH₄ und anschließender Graphitofen-AAS (600° C) beruhen. Die Eichung erfolgt mit einfachen Eichkurven, die mit wässrigen Lösungen hergestellt werden (Empfindlichkeit: 24±4 bzw. 72±17 pg/0,0044 A für As bzw. Se). Die absoluten Nachweisgrenzen liegen bei 30 pg As und 70 pg Se. Die Präzision beträgt 2–3% für As und 5–10% für Se.

     

Application of tertiary amines for arsenic and selenium signal enhancement and polyatomic interference reduction in ICP-MS analysis of biological samples

Water soluble tertiary amines enhance signals and decrease polyatomic chloride interferences in the direct inductively coupled plasma – mass spectrometric (ICP-MS) determination of As and Se in biological samples. Preliminary experiments with amine concentrations and nebulizer flow rates produced element and interference signal intensity changes. Arsenic and Se ICP-MS determination parameters have been optimized by a simplex procedure with amines in an argon plasma or without amines but with addition of N₂ to the Ar. Variables include RF (radio frequency) power, nebulizer gas flow rate, intermediate gas flow rate, and amine concentration or nitrogen gas flow rate. Detection limit, minimization of polyatomic ion intensities, and reproducibility have been evaluated as reponse factors. The signal enhancement and element-to-molecular interference ratios differ to some extent with analyte intensity optimum operating conditions. The detection limits with addition of nitrogen (16 pg mL^–1 for As and 180 pg mL^–1 for Se) or of amines (8 pg mL^–1 for As and 120 pg mL^–1 for Se) and the extent of chloride interference minimization were compared. Amines addition was more beneficial. Biological standard reference materials and food and fecal samples were analyzed following different sample dissolution procedures.     

Evaluation of non-chromatographic approaches for speciation of extractable As(III) and As(V) in environmental solid samples by FI-HGAAS

Non-chromatographic speciation approaches have been developed for determination of water-soluble and phosphate-exchangeable As(III) and As(V) in certified reference materials of coal fly ash and sediments by FI-HGAAS. A 2_IV^6-2 fractional factorial design was employed for screening optimisation of the flow injection manifold. A simple two-stage sequential extraction protocol involving deionized water and a phosphate buffer as extractants was employed. Determination of both oxidation states of As in the extracts could be accomplished following arsine generation under different reaction conditions, namely, (i) selective determination of As(III) in citric acid medium or using soft generation conditions (i.e. low HCl and NaBH₄ concentrations); (ii) determination of total As in each extract using thioglycollic acid as reaction medium or after pre-reduction of As(V) to As(III) with a KI+ascorbic acid mixture. The As(V) content was estimated by difference between both measurements. Reaction conditions were previously optimised and analytical parameters in each reaction medium were established. Overall, the extractable As content was less than 5% in sediment and fly ash CRMs. The LOD of As was around 0.07 μg l⁻¹ for As(III) determination, and 0.06 μg l⁻¹ for total As determination after prereduction. Liquid chromatography coupled to atomic fluorescence spectrometry with post-column hydride generation was used for comparison.