Uranium determination in seawater by total reflection X-ray fluorescence spectrometry

A study regarding uranium determination in seawater by total reflection X-ray fluorescence (TXRF) spectrometry is reported. Uranium, present in seawater in concentration of about 3.3 ng/mL, was selectively extracted in diethyl ether and determined by TXRF after its preconcentration by evaporation and subsequent dissolution in a small volume of 1.5% suprapure HNO₃. Yttrium was used as an internal standard. Before using diethyl ether for selective extraction of uranium from seawater, its extraction behavior for different elements was studied using a multielement standard solution having elemental concentrations in 5 ng/mL levels. It was observed that the extraction efficiency of diethyl ether for uranium was about 100% whereas for other elements it was negligible. The detection limit of TXRF method for uranium in seawater samples after pre-concentration step approaches to 67 pg/mL. The concentrations of uranium in seawater samples determined by TXRF are in good agreement with the values reported in the literature. The method shows a precision within 5% (1σ). The study reveals that TXRF can be used as a fast analytical technique for the determination of uranium in seawater.     

Trace analysis of high-purity copper by total reflection X-ray fluorescence spectrometry

Total reflection X-ray fluorescence (TXRF) analysis after the separation of matrix element was studied for the determination of trace impurity elements (Ca, Sc, V, Cr, Mn, Fe, Co, Ni and Zn) in high purity copper. Matrix copper was removed by electrolysis (0.2 A, 8 h) of a nitric acid solution. A 10 μL aliquot of the remaining solution of the electrolysis was dropped on a silicon-wafer sample-carrier and dried in a vacuum. This was repeated five times and the precipitate of five 10 μL-aliquots was analyzed by TXRF using a W-Lβ beam with an incident angle of 0.05?°. TXRF analytical values were obtained by using relative sensitivity factors of the analytes to the internal standard element (Pd). Detection limits of the analytes ranges from 0.077 ng for Zn to 0.785 ng for Ca.     

Trace analysis of high-purity copper by total reflection X-ray fluorescence spectrometry

Total reflection X-ray fluorescence (TXRF) analysis after the separation of matrix element was studied for the determination of trace impurity elements (Ca, Sc, V, Cr, Mn, Fe, Co, Ni and Zn) in high purity copper. Matrix copper was removed by electrolysis (0.2 A, 8 h) of a nitric acid solution. A 10 μL aliquot of the remaining solution of the electrolysis was dropped on a silicon-wafer sample-carrier and dried in a vacuum. This was repeated five times and the precipitate of five 10 μL-aliquots was analyzed by TXRF using a W-Lβ beam with an incident angle of 0.05 °. TXRF analytical values were obtained by using relative sensitivity factors of the analytes to the internal standard element (Pd). Detection limits of the analytes ranges from 0.077 ng for Zn to 0.785 ng for Ca. Received: 25 December 1997 / Revised: 30 March 1998 / Accepted: 2 April 1998     

Element determination in natural biofilms of mine drainage water by total reflection X-ray fluorescence spectrometry

Human impacts like mining activities lead to higher element concentration in surface waters. For different pollution levels, the consequences for aquatic organisms are not yet investigated in detail. Therefore, the aim of this investigation is to determine the influence of mining affected surface waters on biofilms.Elements like heavy metals can be absorbed on cell walls and on polymeric substances or enter the cytoplasm of the cells. Thus, they are important for the optimization of industrial biotechnological processes and the environmental biotechnology. Beyond this, biofilms can also play an important role in wastewater treatment processes and serve as bioindicators in the aquatic environment.The presented total reflection X-ray fluorescence spectroscopic investigation was performed to compare the element accumulation behavior of biofilms grown on natural or on artificial materials of drainage water affected by former copper mining activities. A high salt and heavy metal pollution is characteristic for the drainage water. For an assessment of these results, samples from stream Schlenze upstream the confluence with the drainage water, a small tributary of the Saale River in central Germany, were analyzed, too.     

Simultaneous determination of elemental content in water samples by total reflection X-ray fluorescence and atomic absorption spectrometry

An analytical exercise between two laboratories was performed in order to compare the elemental composition of a water sample. The metal concentration of Cr, Cu, Fe, Mn, Ni, Pb, and Zn in the water sample was analyzed by Total Reflection X-Ray Fluorescence and Atomic Absorption Spectrometry. The analysis by Total Reflection X-Ray Spectrometry was realized by an Ital Structures TX-2000 and the analysis by Atomic Absorption Spectrometry was made by a Perkin Elmer Spectrophotometer Model 3110. Results show a good agreement in the metal concentrations obtained by both techniques. The variation coefficient between the results with both techniques was less than 14%. Therefore, it is possible to conclude that both techniques are reliable and adequate for the determination of these elements in environmental water samples.     

Determination of copper,iron and zinc in spirituous beverages by total reflection X-ray fluorescence spectrometry

The concentration of copper in traditional homemade alcoholic distillates produced in Venezuela (Cocuy de Penca) were determined by total reflection X-ray fluorescence (TXRF) using vanadium as internal standard. The results were compared to those obtained by flame atomic absorption spectrometry (FAAS). Three preparative methods of addition of vanadium were compared: classical internal standard addition, ‘layer on layer’ internal standard addition and in situ addition of internal standard. The TXRF procedures were accurate and the precision was comparable to that obtained by the FAAS technique. Copper levels were above the maximum allowed limits for similar beverages. Zinc and iron in commercial and homemade distilled beverages were also analyzed by TXRF with in situ addition of internal standard demonstrating the usefulness of this technique for trace metal determination in distillates.     

Determination of fluorine by total reflection X-ray fluorescence spectrometry

There is a growing interest in determination of low Z elements, i.e. carbon to phosphorus, in various samples. Total reflection X-ray fluorescence spectrometry (TXRF) has been already established as a suitable trace element analytical method with low sample demand and quite good quantification limits. Recently, the determinable element range was extended towards Z = 6 (carbon).     

Investigation of polyelectrolytes by total reflection X-ray fluorescence spectrometry

Water soluble polyelectrolyte samples containing mono-, bi- and trivalent metal ions were investigated without any pretreatment. Acid digestion of linear polymers may lead to a product insoluble in water so the digestion has to be avoided. The determination of analytical characteristics and limitations of the total reflection X-ray fluorescence (TXRF) analysis for poly(vinylalcohol-vinylsulfate) copolymers containing the following cations: Cs⁺; Ba²⁺; Cu²⁺ and La³⁺ are presented in this communication. On the basis of our results efficiency of ion-exchange during preparation of polyelectrolytes and stoichiometry of the end-product were determined. TXRF results were compared with data gained by inductively coupled plasma atomic emission spectrometry (ICP-AES) measurements except in the case of Cs⁺, which has poor sensitivity in ICP-AES. Good agreement was found between the results of the two techniques and calculations from titrimetric data. Concentration of Li⁺ and Mg²⁺ in polymer samples was measured only by ICP-AES.     

Trace element determination in thorium oxide using total reflection X-ray fluorescence spectrometry

Applicability of Total Reflection X-ray Fluorescence (TXRF) spectrometry for the determination of trace metals at concentration of µg/g level in thorium oxide was studied. The TXRF spectrometer was calibrated using a multielement standard solution and the method was validated by analyzing another multielement standard solution. Sample preparation conditions were optimized for the TXRF determinations of trace metals in thorium oxide. The elements K, Ca, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Sr, Y, Ba and Pb present in thorium oxide standards were determined after dissolving them in HNO₃/HF mixture and separating the bulk matrix, thorium, by solvent extraction using tri-n-butyl phosphate (TBP) and tri-n-octyl phosphine oxide (TOPO) as extractants. A comparison of TXRF determined concentrations of trace elements Ca, V, Cr, Mn, Fe, Ni and Cu with the certified values shows that TXRF determined concentrations have an RSD of 20% (1 s for n = 4) and are within an agreement of 20% of the certified values in most of the cases.     

Characterization of nuclear materials by total reflection X-ray fluorescence spectrometry

Nuclear energy is one of the available energy options for long term energy security of world. In order to produce electricity using this mode of energy generation in an efficient and safe manner, it is necessary that the materials used for such energy generation comply with the specifications assigned. The major and trace composition of these materials is an important specification for their quality control. Different analytical techniques are used for such quality control. Total reflection X-ray fluorescence (TXRF) is a comparatively new technique having several features well suited for trace and major element determinations in nuclear materials. However, this technique has not been used so far extensively for characterization of nuclear materials. The present paper gives a brief introduction of TXRF, its suitability for nuclear material characterization and some details of the TXRF studies made in our laboratory for the characterization of nuclear materials.     

A method for trace element determination of single Daphnia specimens using total reflection X-ray fluorescence spectrometry

Two new preparation techniques for total-reflection X-ray fluorescence (TXRF) element determination of single freshwater crustacean specimens (dry weight: 3–40 μg ind⁻¹) have been developed and tested using Daphnia pulex from a deep, oligotrophic freshwater lake located in southern Chile. Dry method: Specimens were washed with 0.2 μm filtered lake water and frozen in liquid nitrogen. The freeze-dried Daphnia specimens were weighed using an ultra-fine microbalance and placed on quartz glass carriers for TXRF analysis. Wet method: Specimens were washed with 0.2 μm filtered lake water and placed on quartz glass carriers for TXRF analysis and dried in air. The dry weight was determined using the previously established body length–dry weight relationship. Method validation for both the dry and the wet preparation method in combination with TXRF spectrometry for the element determination in small single freshwater crustaceans showed that both methods can be used for routine investigations. There were no significant differences between the dry and the wet methods concerning the elements Ca, K, Fe, Zn, Br, P, Cu, but the determination of Mn, S and Sr revealed significant differences between the two methods. It seems that the dry method yields more precise results, but the wet method is easier to handle in the field when samples cannot be fixed with liquid nitrogen.     

Analytical approaches for Hg determination in wastewater samples by means of total reflection X-ray fluorescence spectrometry

At present, there is a considerable interest in Hg monitoring in wastewater samples due to its widespread occurrence and the high toxicity of most of its compounds. Hg determination in water samples by means of total reflection X-ray fluorescence spectrometry (TXRF) entails some difficulties due to the high vapor pressure and low boiling point of this element that produce evaporation and loss of Hg from the surface of the reflector during the drying process, commonly used for sample preparation in TXRF analysis.The main goal of the present research was to develop a fast and simple chemical strategy to avoid Hg volatilization during the analysis of wastewater samples by TXRF spectrometry. Three different analytical procedures were tested for this purpose: (i) increasing the viscosity of the wastewater sample by adding a non-ionic surfactant (Triton^® X-114), (ii) Hg immobilization on the quartz reflectors using the extractant tri-isobutylphosphine (Cyanex 471X) and (iii) formation of a stable and non-volatile Hg complex into the wastewater sample. The best analytical strategy was found to be the formation of a Hg complex with thiourea (pH = 10) before the deposition of 10 μL of sample on the reflector for following TXRF analysis. Analytical figures of merit such as linearity, limits of detection, accuracy and precision were carefully evaluated. Finally, the developed methodology was applied for the determination of Hg in different types of wastewater samples (industrial effluents, municipal effluents from conventional systems and municipal effluents from constructed wetlands).     

Trace analysis of high-purity iron by total reflection X-ray fluorescence spectrometry

Summary A combined procedure enabling simultaneous multielement analysis of trace impurities in high-purity iron is presented. After removal of the iron matrix by solvent extraction with methyl isobutyl ketone, the trace elements Ti, V, Cr, Mn, Ni, Cu, Pb and Bi are determined by means of total reflection X-ray fluorescence analysis. Detection limits are found in the range of 100 ng/g. The reliability of the method is verified by the analysis of commercial high-purity iron and by the comparison of analytical data obtained by ICP-AES.     

Determination of sulphur in uranium matrix by total reflection X-ray fluorescence spectrometry

The possibility of sulphur determination in uranium matrix by total reflection x-ray fluorescence spectrometry (TXRF) has been studied. Calibration solutions and samples of sulphur in uranium matrix were prepared by mixing uranium in form of a standard uranyl nitrate solution and sulphur in the form of Na₂SO₄ standard solution, prepared by dissolving Na₂SO₄ in Milli-Q water. For major element analysis of sulphur, it was determined without separation of uranium whereas for the trace level determinations, uranium was first separated by solvent extraction using 30% tri-n-butyl phosphate (TBP) in dodecane as an extractant. In order to countercheck the TXRF results, a few samples of Rb₂U(SO₄)₃, a chemical assay standard for uranium, were diluted to different dilutions and sulphur content in these solutions were determined. The TXRF determined results for trace determinations of sulphur in these diluted solutions were counterchecked after addition of another uranium solution, so that sulphur is at trace level compared to uranium, separating uranium from these solution mixtures using TBP extraction and determining sulphur in aqueous phase by TXRF. For such TXRF determinations, Co was used as internal standard and W Lα was used as excitation source. The precision and accuracy of the method was assessed for trace and major element determinations and was found to be better than 8% (1σ RSD) and 15% at a concentration level of 1 μg/mL of sulphur measured in solutions whereas for Rb₂U(SO₄)₃, these values were found to be better than 4 and 13%, respectively.     

Direct determination of trace elements in boron nitride powders by slurry sampling total reflection X-ray fluorescence spectrometry

The use of slurry sampling total reflection X-ray fluorescence spectrometry (SlS-TXRF) for the direct determination of Ca, Cr, Cu, Fe, Mn and Ti in four boron nitride powders has been described. Measurements of the zeta potential showed that slurries with good stabilities can be obtained by the addition of polyethylenimine (PEI) at a concentration of 0.1 wt.% and by adjusting the pH at 4. For the optimization of the concentration of boron nitride in the slurries the net line intensities and the signal to background ratios were determined for the trace elements Ca and Ti as well as for the internal standard element Ga in the case of concentrations of boron nitride ranging from 1 to 30 mg mL⁻¹. As a compromise with respect to high net line intensities and high signal to background ratios, concentrations of 5 mg mL⁻¹ of boron nitride were found suitable and were used for all further measurements. The limits of detection of SlS-TXRF for the boron nitride powders were found to range from 0.062 to 1.6 μg g^– 1 for Cu and Ca, respectively. Herewith, they are higher than those obtained in solid sampling and slurry sampling graphite furnace atomic absorption spectrometry (SoS-GFAAS, SlS-GFAAS) as well as those of solid sampling electrothermal evaporation inductively coupled plasma optical emission spectrometry (SoS-ETV-ICP-OES). For Ca and Fe as well as for Cu and Fe, however, they were found to be lower than for GFAAS and for ICP-OES subsequent to wet chemical digestion, respectively. The universal applicability of SlS-TXRF to the analysis of samples with a wide variety of matrices could be demonstrated by the analysis of certified reference materials such as SiC, Al₂O₃, powdered bovine liver and borate ore with a single calibration. The correlation coefficients of the plots for the values found for Ca, Fe and Ti by SlS-TXRF in the boron nitride powders as well as in the before mentioned samples versus the reference values for the respective samples over a concentration range from 2.5 to 1470 μg g^– 1 were found to be 0.995, 0.991 and 0.997, respectively.     

Capability and limitations of the determination of sulfur in inorganic and biological matrices by total reflection X-ray fluorescence spectrometry

The capability and limitations of TXRF were explored for the determination of the light element sulfur in inorganic and biological samples. The recovery rates of sulfur were measured with tungsten L-radiation in the dry residues of various sulfates and sulfur containing amino acids with a sulfur concentration ranging from 0.5 to 20 mg/l. Furthermore, the surface topography of the dry residues of the samples was investigated by scanning electron microscopy (SEM) and their thickness profiles were recorded by an Alpha-Step. The results show that the reliable determination of sulfur in inorganic samples depends on the cation involved. Alkali sulfates tend to form bulky residues which disturb the determination of sulfur distinctly due to absorption effects of the soft sulfur K radiation. In this case the use of smoothing detergents like 1% HF, 1% malic acid and 2% hydrazine hydrate is necessary for the determinations with reasonable accuracy (tolerance range: ±10% of the recovery rate). The results for the biological samples measured agree well with the expected values. The investigations lead to the conclusion that TXRF combined with a proper sample preparation is well suited for the determination of sulfur in samples of various matrices in a wide range of concentrations.     

Element determination in medieval soil samples by total reflection X-ray fluorescence analysis

An aqua regia extraction procedure for heavy metals in soils optimised for total reflection X-ray fluorescence analysis is presented. The procedure is applied to 92 soil samples of medieval layers from the city area of Dortmund. Sixteen elements (P, S, K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, Rb, Sr, Ag, Sn, and Pb) were used to characterise 17 sample sites. The results are projected onto the medieval urban structure of Dortmund. Two sites loaded with non-ferrous heavy metal could be detected and correlated with archaeological data. The efficiency and repeatability of the proposed extraction procedure is discussed.     

Simultaneous determination of copper and iron in automotive gasoline by X-ray fluorescence after pre-concentration on cellulose paper

This paper proposes an alternative analytical method using energy dispersive X-ray fluorescence (EDXRF) to determine Fe and Cu in gasoline samples. In the proposed procedure, samples were distilled and the distillation residues were spotted on cellulose paper disk to form a uniform thin film and to produce a homogeneous and reproducible interface to the XRF instrument. The disks were dried at 60 °C for 20 min and copper and iron were determined directly in the solid phase at 6.40 and 8.04 keV, respectively. The calibration curves showed linear response in the 20-800 μg L⁻¹ concentration range of each metal. The precisions (repeatability) calculated from 15 consecutive measurements and defined as the coefficient of variation of solutions containing 100 μg L⁻¹ of Fe and Cu were 7.8 and 8.1%, respectively. The limits of detection (LOD), defined as the analyte concentration that gives a response equivalent to three times the standard deviation of the blank (n = 10), were found to be 10 and 15 μg L⁻¹ for Fe and Cu, respectively. The proposed method was applied to copper and iron determination in gasoline samples collected from different gas stations.     

Determination of Ni,Co, and Cu in seawater by total external reflection X-ray fluorescence spectrometry

Total external reflection X-ray fluorescence spectrometry is a promising method for the highly sensitive determination of heavy metals in seawater, offering such advantages as the mobility of the used equipment and the low cost of analysis. Various methods of sample preparation to the analysis of seawater aimed at the elimination of interferences with the salt matrix were compared. It was shown that the method based on the preliminary extraction of metals as diehyldithiocarbamate complexes followed by back extraction is characterized by the highest efficiency. A procedure was developed for the determination of Ni, Cu, and Co in seawater with limits of detection at a level of 0.16–0.26 μg/L.