ETAAS method for the determination of Cd, Cr, Cu, Mn and Se in blood fractions and whole blood

An electrothermal atomic absorption method (ETAAS) for the direct determination of trace elements (Cd, Cr, Cu, Mn, Se) both in blood fractions (erythrocytes, plasma and lymphocytes) and whole blood was developed. Zeeman background correction and graphite tubes with L'vov platforms were used. Samples were diluted with HNO3/Triton X-100 and pipetted directly into the graphite tube. Ashing, pretreatment and atomization steps were optimized carefully for the different fractions and elements applying different matrix modifiers for each element. For the lymphocyte fraction a multi-fold injection technique was applied. Low detection limits of the ETAAS method (Cd 0.13 microgram/L, Cr 0.11 microgram/L, Cu 0.52 microgram/L, Mn 0.13 microgram/L, Se 0.7 microgram/L of whole blood) combined with small quantities of sample necessary for analysis allow determination of trace elements in this matrix. Verification of possible differences in the trace element status of humans was performed with statistical significance (P < 0.05). In addition, a contribution to the determination of normal values of essential elements was achieved. The method was applied for determination of trace elements in human blood and blood fractions of two groups (n = 50) different in health status.     

Determination of As,Cd, Cu,Hg and Pb in biological samples by modern electrothermal atomic absorption spectrometry

Pollution from heavy metals has increased in recent decades and has become an important concern for environmental agencies. Arsenic, cadmium, copper, mercury and lead are among the trace elements that have the greatest impact and carry the highest risk to human health. Electrothermal atomic absorption spectrometry (ETAAS) has long been used for trace element analyses and over the past few years, the main constraints of atomic absorption spectrometry (AAS) methods, namely matrix interferences that provoked high background absorption and interferences, have been reduced. The use of new, more efficient modifiers and in situ trapping methods for stabilization and pre-concentration of these analytes, progress in control of atomization temperatures, new designs of atomizers and advances in methods to correct background spectral interferences have permitted an improvement in sensitivity, an increase in detection power, reduction in sample manipulation, and increase in the reproducibility of the results. These advances have enhanced the utility of Electrothermal atomic absorption spectrometry (ETAAS) for trace element determination at μg L⁻¹ levels, especially in difficult matrices, giving rise to greater reproducibility, lower economic cost and ease of sample pre-treatment compared to other methods. Moreover, the recent introduction of high resolution continuum source Electrothermal atomic absorption spectrometry (HR-CS-ETAAS) has facilitated direct solid sampling, reducing background noise and opening the possibility of achieving even more rapid quantitation of some elements. The incorporation of flow injection analysis (FIA) systems for automation of sample pre-treatment, as well as chemical vapor generation renders (ETAAS) into a feasible option for detection of As and Hg in environmental and food control studies wherein large numbers of samples can be rapidly analyzed. A relatively inexpensive approach with low sample consumption provide additional advantages of this technique that reaches figures of merit equivalent to Inductively coupled plasma mass spectrometry (ICP-MS). Herein is presented an overview of recent advances and applications of (ETAAS) for the determination of As, Cd, Cu, Hg and Pb in biological samples drawn from studies over the last decade.     

ETAAS method for the determination of Cd, Cr, Cu, Mn and Se in blood fractions and whole blood

An electrothermal atomic absorption method (ETAAS) for the direct determination of trace elements (Cd, Cr, Cu, Mn, Se) both in blood fractions (erythrocytes, plasma and lymphocytes) and whole blood was developed. Zeeman background correction and graphite tubes with L’vov platforms were used. Samples were ¶diluted with HNO₃/Triton X-100 and pipetted directly ¶into the graphite tube. Ashing, pretreatment and atomization steps were optimized carefully for the different fractions and elements applying different matrix modifiers ¶for each element. For the lymphocyte fraction a multi-fold injection technique was applied. Low detection limits ¶of the ETAAS method (Cd 0.13 μg/L, Cr 0.11 μg/L, ¶Cu 0.52 μg/L, Mn 0.13 μg/L, Se 0.7 μg/L of whole blood) combined with small quantities of sample necessary for analysis allow determination of trace elements in this matrix. Verification of possible differences in the trace element status of humans was performed with statistical significance (P < 0.05). In addition, a contribution to the determination of normal values of essential elements was achieved. The method was applied for determination of trace elements in human blood and blood fractions of two groups (n = 50) different in health status.     

悬浊液直接进样非火焰原子吸收法测定蔬菜样品中微量铬的研究

本文通过用直接悬浊液进样原子吸收法对新鲜蔬菜中铬的测定,研究了各种实验条件,并建立了实际测定新鲜蔬菜中微量元素的方法。该法将可用于食品。     

Determination of Hg,Cd, Mn,Pb and Sn in seafood by solid sampling Zeeman atomic absorption spectrometry

Direct solid sampling Zeeman atomic absorption spectrometric methods were developed and applied to the determination of mercury, cadmium, manganese, lead and tin in seafood. All elements but mercury were measured by a third generation Zeeman atomic absorption spectrometry combined with an automatic solid sampler. In 3-field- and dynamic mode the calibrations concentration range was substantially extended and high amounts of analyte were detectable without laborious dilution of solid samples. The measurements were based on calibrations using certified reference materials of organic matrices. In case solid certified reference materials were not available calibration by aqueous standard solutions was proved to be an alternative. No matrix effects were observed under the optimized conditions. Results obtained were in good agreement with the certified values. Solid sampling Zeeman atomic absorption spectrometry proved to be a reliable, rapid and low-cost method for the control of trace elements in seafood.     

Advantages of the iridium permanent modifier in fast programs applied to trace-element analysis of plant samples by electrothermal atomic absorption spectrometry

The application of a fast program combined with the advantages of the iridium permanent modifier is proposed for trace element analysis of plant samples by electrothermal atomic absorption spectrometry (ETAAS). For two volatile elements (Cd, Pb) and two mid-refractory elements (Cr, Ni) it was demonstrated that coating of the platform or of the tube atomization area with Ir is an efficient means of improving the accuracy and precision of results. A detailed study of interference from individual main matrix components and from composite plant matrices has confirmed the usefulness of the whole approach. The validity of the method has been confirmed by analysis of eight reference plant materials.     

Direct determination of traces of Ag, Cd, Pb, Bi, Cr, Mn, Co, Ni, Li, Be, Cu and Sb in environmental waters and geological materials by simultaneous multi-element graphite furnace atomic absorption spectrometry with Zeeman-effect background correction

A method was developed for direct determination of minor and trace amounts of Cr, Mn, Cu, Ni, Co, Li, Pb, Cd, Bi, Sb, Be and Ag in silicate rock, lake and stream sediments using a microwave oven dissolution method and a multi-element graphite furnace atomic absorption spectrometer equipped with a Zeeman-effect background correction device. The measurement technique was also suitable for direct determination of trace and ultra-trace amounts of these elements in drinking and seawater samples. A rock or sediment sample was brought into solution in a Teflon vessel by heating in a microwave oven with a mixture of hydrofluoric acid and aqua regia, followed by a further heating with a mixture of boric acid and ethylenediaminetetraacetic acid. The specified elements were directly determined in a group of four elements in one firing and eight elements in two firings from this solution or from a diluted solution using the optimum operating parameters developed in this work. The method, tested with 23 international reference rocks and sediments and seven international quality control and reference water samples, showed good to excellent agreement with the recommended values.     

Advantages of the iridium permanent modifier in fast programs applied to trace-element analysis of plant samples by electrothermal atomic absorption spectrometry

The application of a fast program combined with the advantages of the iridium permanent modifier is proposed for trace element analysis of plant samples by electrothermal atomic absorption spectrometry (ETAAS). For two volatile elements (Cd, Pb) and two mid-refractory elements (Cr, Ni) it was demonstrated that coating of the platform or of the tube atomization area with Ir is an efficient means of improving the accuracy and precision of results. A detailed study of interference from individual main matrix components and from composite plant matrices has confirmed the usefulness of the whole approach. The validity of the method has been confirmed by analysis of eight reference plant materials.     

火焰原子吸收法测定夏枯草果穗的微量元素

使用灰化法处理样品,火焰原子吸收光谱法测定夏枯草果穗中的铬、银、锌、镍、镉、铁、铜的含量。结果表明,除Ag元素未检出外,夏枯草果穗的微量元素含量Cr、Zn、Ni、Cd、Fe、Cu分别为1．024、1．096、36．152、0．580、0．656、6．872μg/g,各元素含量由高到低顺序为：Ni,Cu,Zn,Cr,Fe,Cd,加标回收率为98．6％～115．2％,该法测定快速、简单,原子吸收光谱法测定夏枯草果穗中微量元素具有可行性。     

Developing electrodeposition techniques for preconcentration of ultra-traces of Ni, Cr and Pb prior to arc-atomic emission spectrometry determination

Electrodeposition is known to be proper for separation and preconcentration of extremely low concentrations of analytes from the bulk sample which is instrumentally very simple. In the present research, a combination of electrodeposition with arc atomic emission spectrometry (ED-AAES) method has been developed in order to improve the analytical performance of this spectrometry technique. The results show that sensitivity and detection limits by using ED-AAES were improved 1000–2000 folds over those of normal arc atomic emission spectrometry in determination of the selected elements. The detection limits for measurement of Ni, Cr and Pb were 2.56, 3.05 and 2.11 µg L^{− 1} for monodeposition and 3.31, 3.72 and 3.25 µg L^{− 1} for simultaneously deposition, respectively. The precision of determination was in the range of 2–4% RSD. Typical calibration graphs for these elements were linear up to 100 µg L^{− 1}, depending on the element and matrix.Application of this technique was also tested on determination of the studied elements in an electroplating plant's waste water. The accuracy of technique was verified by comparing the results of the waste water analysis with those of electrothermal atomic absorption spectroscopy as a reference standard method.The obtained results show that the combined technique (ED-AAES) has been progressed substantially toward the ultimate goal of direct interference-free determination of trace analysis in complex samples by AAES.     

Derivative flame atomic absorption spectrometry and its application in trace analysis

Flame atomic absorption spectrometry (FAAS) is an accepted and widely used method for the determination of trace elements in a great variety of samples. But its sensitivity doesn’t meet the demands of trace and ultra-trace analysis for some samples. The derivative signal processing technique, with a very high capability for enhancing sensitivity, was developed for FAAS. The signal models of conventional FAAS are described. The equations of derivative signals are established for FAAS, flow injection atomic absorption spectrometry (FI-FAAS) and atom trapping flame atomic absorption spectrometry (AT-FAAS). The principle and performance of the derivative atomic absorption spectrometry are evaluated. The derivative technique based on determination of variation rate of signal intensity with time (dI/dt) is different from the derivative spectrophotometry (DS) based on determination of variation rate of signal intensity with wavelength (dI/dλ). Derivative flame atomic absorption spectrometry (DFAAS) has higher sensitivity, lower detection limits and better accuracy. It has been applied to the direct determination of trace elements without preconcentration. If the derivative technique was combined with several preconcentration techniques, the sensitivity would be enhanced further for ultra-trace analysis with good linearity. The applications of DFAAS are reviewed for trace element analysis in biological, pharmaceutical, environmental and food samples.     

Open wet ashing of some types of biological materials for the determination of mercury and other toxic elements

An open wet decomposition procedure for trace element analysis of biological material has been worked out. It is based on the utilization of nitric acid, hydrochloric acid and hydrogen peroxide and is well suited for the determination of As, Bi, Cd, Cr, Hg, Pb, Sb, Se and Tl. For these elements the recoveries were examined by the radiotracer technique, with lichens, pine needles, grass and human hair as representative biological samples. In addition to the conventional labelling technique, use was also made of in situ labelling. In all cases, recoveries between 93 and 100% were achieved, which are adequate for quantitative trace element analysis.     

Electrothermal atomic absorption spectrometric determination of chromium,iron and nickel in lithium metal

Graphite-furnace atomic absorption spectrometry is applied to the determination of traces of Cr, Fe and Ni in lithium metal, after dissolution as lithium chloride. Direct determination is applied to lithium samples containing higher levels of impurities, but determination in pure lithium samples requires preliminary separation by lanthanum hydroxide coprecipitation. With this enrichment, detection limits of 0.02–0.25 μg g^-1 are obtained using 0.5-g samples of lithium. The accuracy of the procedure was checked by analysis of lithium samples by the proposed coprecipitation method, by direct determination, and by determination after extraction, atomic absorption spectrometry being used in all cases.     

Flame AAS/flame AES for trace determination in fresh and used lubricating oils with sample introduction by hydraulic high-pressure nebulization

In hydraulic high-pressure nebulization (HHPN) an aerosol is produced by means of an HPLC-pump and a special nebulization nozzle, applying a pressure of about 200 bar. This spray technique has been employed for sample introduction of mineral oil samples in flame atomic absorption/flame emission spectrometry. The determination of the trace elements Al, Cr, Cu, Fe, K, Na, Ni, Pb, Si and V has been investigated. Viscosity hardly acts upon the sensitivity of the determination, thereby avoiding a time consuming dilution of oil samples. By means of two interconnecting sampling valves a calibration method based on the standard addition technique can be performed which is both simple and easy to carry out. In samples of used oils, results for Cu and Pb equalled those of XRF-analysis. Regarding Fe traces, data obtained from AAS and XRF measurement correlate. In comparison with sample uptake by pneumatic nebulization, which is restricted to diluted oil samples, detection limits decrease by a factor of 2 to 4, indicating the dilution required in pneumatic nebulization.     

三种癌的铬、锰、锌、铜、铁、镁、钙含量

为进一步阐明癌组织与宏量、徽量元素的关系．用原子吸收光谱法测定胃癌、大肠癌、乳腺癌组织及其癌旁组织和同体正常组织中铬、锰、锌、铁、镁、铜和钙的含量．试找这些元素在癌、癌旁及其同体正常组织中的分布规律．测定结果；在胃癌组织中锌的含量比癌旁组织、同体正常组织少。铜的含量比正常组织多。其余五种元素的含量在这三个组织之间比较无明显差异；在大肠癌组织中锰、镁的音量比癌旁组织多．其他五种元素的含量在这三个组织之间比较，无明显差异；在乳腺癌组织中铬，锰和铁的含量比正常组织多。锌、镁、钙的含量比同体正常组织和癌旁组织多，铜的含量在这三个组织中比较无明显差异，总之，胃癌、大肠癌及乳腺癌组织及其癌旁组织和同体正常组织中。上述七种元素的音量是不同的。特别是在乳腺癌组织中除铜以外的六种元素的含量都比正常组织多．值得进一步研究．     

Flame AAS/flame AES for trace determination in fresh and used lubricating oils with sample introduction by hydraulic high-pressure nebulization

In hydraulic high-pressure nebulization (HHPN) an aerosol is produced by means of an HPLC-pump and a special nebulization nozzle, applying a pressure of about 200 bar. This spray technique has been employed for sample introduction of mineral oil samples in flame atomic absorption/flame emission spectrometry. The determination of the trace elements Al, Cr, Cu, Fe, K, Na, Ni, Pb, Si and V has been investigated. Viscosity hardly acts upon the sensitivity of the determination, thereby avoiding a time consuming dilution of oil samples. By means of two interconnecting sampling valves a calibration method based on the standard addition technique can be performed which is both simple and easy to carry out. In samples of used oils, results for Cu and Pb equalled those of XRF-analysis. Regarding Fe traces, data obtained from AAS and XRF measurement correlate. In comparison with sample uptake by pneumatic nebulization, which is restricted to diluted oil samples, detection limits decrease by a factor of 2 to 4, indicating the dilution required in pneumatic nebulization.     

Determination of some trace metals in water and sediment samples by flame atomic absorption spectrometry after coprecipitation with cerium (IV) hydroxide

A cerium(IV) hydroxide coprecipitation method was developed for the determination of some trace elements (Cu, Co, Pb, Cd, Ni) in aqueous solutions, water and sediment samples by flame atomic absorption spectrometry (AAS). Several parameters governing the efficiency of the coprecipitation method were evaluated including pH of sample solution, amount of carrier element, volume of sample solution and the effect of possible matrix ions The procedure was validated by the analysis of GBW 07309 standard reference material sediment and by use of a method based on a solid phase extraction.     

A new strategy for preparation of hair slurries using cryogenic grinding and water-soluble tertiary-amines medium

The investigation of trace metal contents in hair can be used as an index of exposure to potentially toxic elements. Direct determination of Cd, Cu and Pb in slurries of hair samples was investigated using an atomic absorption spectrometer with Zeeman-effect background correction. The samples were pulverized in a freezer/mill for 13 min, and hair slurries with 1.0 g l⁻¹ for the determination of Cu and Pb, and 5.0 g l⁻¹ for the determination of Cd, respectively, were prepared in three different media: 0.1% v/v Triton X-100, 0.14 mol l⁻¹ HNO₃, and 0.1% v/v of CFA-C, a mixture of tertiary amines. The easiest way to manipulate the hair samples was in CFA-C medium. The optimum pyrolysis and atomization temperatures were established with hair sample slurries spiked with 10 μg l⁻¹ Cd²⁺, 30 μg l⁻¹ Pb²⁺, and 10 μg l⁻¹ Cu²⁺. For Cd and Pb, Pd was used as a chemical modifier, and for Cu no modifier was needed. The analyte addition technique was used for quantification of Cd, Cu, and Pb in hair sample slurries. A reference material (GBW076901) was analyzed, and a paired t-test showed that the results for all elements obtained with the proposed slurry sampling procedure were in agreement at a 95% confidence level with the certified values. The cryogenic grinding was an effective strategy to efficiently pulverize hair samples.     

Quality Control in Element Analysis of Plant Materials

A worldwide laboratory intercomparison was organized by the International Atomic Energy Agency's Analytical Quality Control Services (AQCS) involving the determination of elements in plant materials used for human consumption. The main purpose of this work was to evaluate the performance of our analytical methods including sample preparation and to obtain new reference materials that can be used in our further work. Both materials (spinach and cabbage) were analyzed by inductively coupled plasma atomic emission spectrometry (ICP-AES) and instrumental neutron activation analysis (INAA). Six subsamples of each material were subjected to our digestion procedure and the solutions were measured by ICP-AES. The dried samples were analyzed using INAA. Up to 26 elements were determined in plant materials. For easy review of our data a score has been calculated based on the reference value for each measured element. According to our results the ICP-AES technique was useful for determination of the following elements: Ba, Ca, Cr, Fe, K, Mn, Mo, P, S, Sr, Ti. The INAA method was reliable for measurement of Ce, Co, Mn, Na, Rb, Th, and V.     

Matrix effects during trace element analysis in plant samples by inductively coupled plasma atomic emission spectrometry with axial view configuration and pneumatic nebulizer

Plant sample matrix effects have been investigated during trace element analysis by inductively coupled plasma atomic emission spectrometry with axial view and pneumatic nebulizer. Eight elements often analyzed in environmental samples were studied: As, Cd, Co, Cr, Cu, Ni, Pb and Se. To simulate the effects caused by digested plant samples, the spectral line profiles of analytes were measured on solutions containing various concentrations of elements encountered in plant matrix such as K, Ca and Mg. Depressions in the emission intensities occurred and were more dramatic with high concentrations of the concomitant species. The inter-element effects were found to be caused by the matrix amount entering into the central channel of the plasma. In fact, energy consumed for droplets desolvation and particles of salts vaporization leads to lower plasma temperatures and produce changes in excitation mechanisms. Ion emissions were especially affected. The matrix effects can be removed using a high generator power (1.4 kW) and a moderate uptake flow rate of solution into the plasma (pump speed: 15 rev./min). The use of the natural plant sample led to the same conclusions. These operating conditions decreased the sensitivity but routine analyses of the plant material could be carried out.