川芎中锌、锰、铁、钙、镁元素的形态分析

利用原子吸收分光光度法对中药川芎中锌、锰、铁、钙、镁五种元素的形态进行了研究。用阳离子交换树脂将川芎可溶态中锌、锰、铁、钙、镁分为游离态和非游离态,建立了两形态的分离分析方法。结果表明,可溶态中锌全部以游离态存在,不存在非游离态;钙和镁存在少量非游离态;锰和铁存在超过50％的非游离态。     

新疆茜草中铜锰铁锌钙镁的形态分析

结合新疆茜草的药用价值,用煎煮法对新疆茜草中的Cu、Mn、Fe、Zn、Ca和Mg进行了含量和形态分析.用0.45 μm滤膜分离提取液中的可溶态与悬浮态,用D101大孔吸附树脂分离可溶态中的有机态与无机态.对水煎渣依次用丙酮和盐酸提取有机态和无机态,用原子吸收光谱(AAS)法对六种元素的各个形态进行测定.结果表明:新疆茜草中各个元素的提取率在31.5%～45.2%之间,六种微量元素的相对标准偏差在0.11%～1.23%,回收率在92.5%～104.7%.     

穿心莲中7种微量元素的形态分析

采用传统煎煮法对穿心莲中的铁、锰、铜、锌、铝、硼和锶7种微量元素进行提取,用0.45 μm微孔滤膜分离提取液中的可溶态与悬浮态;用LSA-10大孔吸附树脂分离可溶态中的有机态与无机态;并用正辛醇-水分配体系在模拟人体胃肠酸度的条件下,将可溶态中各待测元素分离为醇溶态和水溶态;采用电感耦合等离子原子发射光谱法(ICP-A...     

半枝莲中铜,锰,锌的初级形态分析

按照微量元素初级形态分析要求,对抗癌中药半枝莲的原药、头煎、二煎、及其残渣、用0.45μm膜分离煎液所得的颗粒物及可溶态共7种样品中的铜、锰、锌进行测定。通过计算得到一系列形态分析参数。其中原药中微量元素含量Cu 18.56×10~(-6),Zn 149.4×10~(-6),Mn 218.8×10~(-6)。头煎提取率:Cu32.67％、Zn 43.69％、Mn 44.49％。二煎提取率:Cu 1.61％、Zn 16.13％、Mn 5.01％。     

治肺癌复方中铬,镍的形态分析

本实验对含１３味中药的治肺癌复方原药，头煎及二煎残渣和浸汁，经０．４５μ膜分离的颗粒物，可溶态，以及可溶态分别通过阳离子交换树脂，用三氯甲烷萃取后所得各自柱截留物，穿过物，有机相，水相等共１５个样品中铬，镍，按照中药微量元素初级和次形态分析的要求，进行分析测定，以此计算出一套形态分析参数和相关数据，为探讨中草约中微量元素的化学形态提供了新的信息。     

全蝎中4种微量元素的形态分析

对中药全蝎中铜、锌、铁和镁4种微量元素存在的形态及含量进行了研究。文中叙述了全蝎样品中元素的各种形态(可溶态、悬浮态、无机态、有机态)的提取方法和分离,采用火焰原子吸收光谱法测定了各试液中4种微量元素的含量。结果显示,全蝎中4种元素的总提取率在39.9%~63.2%之间,浸留比在73.6%~126.0%之间,悬浮态颗粒吸附率在10%左右,铜、锌、铁、镁的有机态与无机态的比例在250.0%~550.0%之间。     

火焰原子吸收光谱法分析香青兰中微量元素的溶出特性及化学形态

结合香青兰的药用功效,对其铜、锌、锰、铁、镁、镍6种微量元素的含量和形态进行了分析.分别用0.45 μm滤膜、D101型大孔吸附树脂,将香青兰水煎液中铜、锌、锰、铁、镁、镍分为悬浮态和可溶态、有机态和无机态;并采取正辛醇-水分配体系模拟水煎液中铜、锌、锰、铁、镁、镍在人体胃肠中的分配情况,建立了上述6种元素的4种形态分离分析方法,用火焰原子吸收光谱法测定6种微量元素的含量、分布及其在不同溶剂中的溶出特性和化学形态.结果表明,方法的回收率在92%～106%范围内,相对标准偏差均在3.8%以下,铜、锌、锰、铁、镁、镍是各以某种形态为主的多种形态共存的混杂体系.     

黄芪中痕量元素的形态分析

对不同产地中药黄芪中铁、锰、铜及锌4种痕量元素存在的形态及其含量进行研究。文中叙述了分离各种形态的方法及其试液,包括样品中测定痕量元素总量的试液,水煎液的可溶态和悬浮态的试液,可溶态试液中有机形态、无机形态、稳定形态和不稳定形态的试液,以及水煎药渣中4种元素测定溶液等8种试液的制备方法。采用电感耦合等离子体原子发射光谱法测定了各试液中4种痕量元素的含量。以可溶无机形态的试液为基体,用标准加入法作回收试验,测得4种元素的回收率在97.6%～102.0%之间。     

火焰原子吸收光谱法分析香菇中微量元素的形态

对香菇中Cu、Zn、Fe、Mn、Ca和Mg进行了微量元素的含量和形态分析.分别用0.45μm滤膜,D101型大孔吸附树脂,将香菇水煎掖中Cu、Zn、Fe、Mn、Ca和Mg分为悬浮态和可溶态、有机态和无机态,用HCl和CCl4处理煎渣,得煎渣无机态和有机态,火焰原子吸收光谱法测定香菇各形态含量.方法的回收率在95.0%～101.7%范围内,相对标准偏差均在2%以下.     

中草药龙胆中微量元素的形态分析

采用传统煎煮法对丽水当地中草药龙胆中钙、锌、铁、铜、锰、铅、镉和铬等8种元素进行提取,并用微孔滤膜分离提取液中可溶态与悬浮态;利用大孔吸附树脂分离可溶态中有机态与无机态;采用正辛醇/水分配体系模拟水煎液中这8种微量元素在人体胃肠中分配情况,再用火焰原子吸收光谱法(FAAS)测定了各种形态中的8种元素。研究结果显示:龙胆中8种元素的提取率在34.25%～74.53%,浸留比在49.58%～371.1%,悬浮态颗粒吸附率在6.5%～29.8%,该法对各元素的加标回收率在91.3%～108.5%;相对标准偏差小于3.5%;锌、铁、铜、锰在正辛醇/水分配体系中溶出性受酸碱性影响大些。     

Metal-Directed Formation of Tetra-, Hexa-, Octa-, and Nonanuclear Complexes of Magnesium,Calcium, Manganese,Copper, and Cadmium

Efficacious metal control of self-assembly of dialkylketipinate dianions leads to completely different supramolecular assemblies. The structures of grid 1 , double-decker 2 , triple-decker 3 , and metalla-spherand 4 were characterized by X-ray crystallographic analyses or by NMR spectroscopy.     

Optimization of parameters for semiempirical methods. III Extension of PM3 to Be,Mg, Zn,Ga, Ge,As, Se,Cd, In,Sn, Sb,Te, Hg,Tl, Pb,and Bi

Using a recently developed procedure for optimizing parameters for semiempirical methods,¹ PM3 has been extended to a total of 28 elements. Average ΔH_f errors for the newly parameterized elements are Be: 8.6, Mg: 8.4, Zn: 5.8, Ga: 14.9, Ge: 11.4, As: 8.5, Se: 11.1, Cd: 2.6, In: 11.3, Sn: 9.0, Sb: 13.7, Te: 11.3, Hg: 6.8, Tl: 6.5, Pb: 7.4, and Bi: 10.9 kcal/mol. For some elements the paucity of data has resulted in a method, which, while highly accurate, is likely to be only poorly predictive.     

猪胰脏中铁钙镁铜铅锌镉锰钴镍的测定

采用硝酸－过氧化氢在自动回流消化仪中消化猪胰脏,火焰原子吸收光度法测定铁、钙、镁、铜、锌、铅、镉、锰、钴、镍的含量。,方法简便,快速,结果令人满意,并对猪胰脏食用价值进行了评价。     

Prediction of the enthalpy of vapourisation for anhydrides,formates, acetates,propionates, butyrates,esters, and ethers

Four analytical correlations based on the use of the corresponding states principle were used to calculate the enthalpy of vapourisation of fluids. Three of these correlations require as inputs the critical temperature and the acentric factor. The fourth requires a molecular Lennard–Jones parameter and the acentric factor. Results for 184 polar and non-polar fluids grouped into 9 families are compared with the values accepted by the Design Institute for Physical Property (DIPPR) project. Recommendations are given for the use of each model and for the choice of the adequate model for each family of fluids.     

ICP-AES法测定铝中铁、硅、铜、镓、镁、锌、锰和钛

用 50g L氢氧化钠溶液溶解铝样品 ,硝酸 (1 1 )酸化 ,以ICP AES测定其中铁、硅、铜、镓、镁、锌、锰和钛等 8种杂质元素。     

ICP-MS测定化妆品中铍、镉、铊、铬、砷、碲、钕、铅

目的：建立化妆品中铍、镉、铊、铬、砷、碲、钕、铅8种有害元素的测定方法。方法：采用电感耦合等离子体质谱法,样品采用微波消解,以钇、锂、铟、铋为内标作定量分析。结果：各元素和内标元素在一定浓度范围内的质量数比值均与浓度呈良好的线性关系,线性方程的相关系数均大于0.9998,平均回收率为95%~104%,相对标准偏差(RSD)均小于3%。结论：该方法灵敏度高,准确,可为化妆品中上述元素的限量检查提供参考。     

Thin-layer chromatographic separation of aldrin,dieldrin, γ-hexachlorocyclohexane,malathion, ethyl-parathion,pentachlorophenol, and of chlordane,dieldrin, γ-hexachlorocyclohexane,malathion, ethyl-parathion,and pentachlorophenol from each other

A thin-layer chromatographic method is reported for the separation of aldrin (or chlordane), dieldrin, γ-hexachlorocyclohexane, malathion, ethyl-parathion, and pentachlorophenol from each other. The procedure, however, does not separate aldrin and chlordane from each other although it does separate either pesticide from the other components. The method employs alumina plates with n-hexane:xylene:benzene:toluene:cyclohexane:methyl cyclohexane (50:50:50:50:50:50:) as developing solvent.     

Enthalpies of dilution of aqueous solutions of formamide,acetamide, propionamide,andN,N-dimethylformamide

The enthalpies of dilution of aqueous solutions of formamide, acetamide, propionamide,N,N-dimethylformamide, and sucrose have been measured from about 0.15 to 2.0 moles-kg ^–1 at 25.0°C. The results of the enthalpy measurements were used to calculate the pairwise enthalpies of interaction for each compound with itself. The equation of Savage and Wood together with their interaction parameters are used to predict the experimental results. All of the predictions are within the standard deviation of the original correlation of Savage and Wood (±220 J-kg-mole ^–2 ). Detailed examination of the results shows that specific effects are present but they are less than 220 J-kg-mole ^–2 . Results on urea and substituted ureas are used to determine interaction coefficients for a urea group with itself and with another CH ₂ group. The result,H _U,U =–280 andH _{U,CH 2} =29 J-kg-mole ^–2 , is an improvement on the previous arbitrary assignment of parameters for urea interactions.