DEPU对上海光源储存环的影响与补偿

上海光源储存环安装了一套由两台椭圆极化波荡器组成的插入件（DEPU）,该插入件尤其是其中一台椭圆极化波荡器的积分场误差引起了闭轨畸变、工作点漂移、耦合度变化、动力学孔径减小等多种效应,这些效应对上海光源储存环的正常运行造成了极大影响。采用校正线圈前馈将最大闭轨畸变降低到10 m的水平,采用四极铁强度前馈将工作点漂移控制在0.001左右,采用斜四极铁前馈将耦合度很好地控制在0.1%左右。通过六极铁在线优化解决了动力学孔径退化的问题,将注入效率保持在80%以上。在接近4年的运行中,补偿方案工作表现很好,轨道补偿的前馈还在不断地完善中。     

合肥同步辐射光源的耦合度校正

在合肥同步辐射储存环中由于四极铁的旋转误差和在六极铁中垂直方向的闭轨畸变等,导致电子水平和垂直两个方向的运动的耦合,耦合度达到12%（测量值）。为降低束流的横向耦合度,提高光源亮度,拟在储存环中安装斜四极铁,探讨了斜四极铁的设计及安装的方法。     

合肥同步辐射光源的耦合度校正

 在合肥同步辐射储存环中由于四极铁的旋转误差和在六极铁中垂直方向的闭轨畸变等,导致电子水平和垂直两个方向的运动的耦合,耦合度达到12%（测量值）。为降低束流的横向耦合度,提高光源亮度,拟在储存环中安装斜四极铁,探讨了斜四极铁的设计及安装的方法。     

工作点反馈系统对同步辐射光源运行稳定性的提升（英文）

上海同步辐射装置(SSRF)储存环上目前已经安装了十台插入元件(IDs)。在用户时间,插入元件的间隙被反复地调整以进行科学实验。虽然使用了插入件前馈系统,但依然存在扰动束流光学的残余四极场,它会导致束流横向振荡工作点的变化,进而影响机器的性能和同步辐射光亮度的稳定。为此,我们研发了一个工作点反馈系统来解决这个问题,并且已经在上海光源储存环上投入了运行,在两周左右的运行周期内,工作点的稳定度达到了±0.001。这个反馈系统还有另一个重要功能,即可以根据监控反馈系统校正电流的变化趋势来判断二极磁铁电源和四极磁铁电源是否存在慢漂问题。为了验证这个工作点反馈的可行性,我们对使用反馈前后几周的束流参数进行了比较,包括储存环注入效率、束流寿命、水平方向束斑尺寸以及β函数的变化情况(beta-beatings)。     

工作点反馈系统对同步辐射光源运行稳定性的提升

上海同步辐射装置（SSRF）储存环上目前已经安装了十台插入元件（IDs）。在用户时间,插入元件的间隙被反复地调整以进行科学实验。虽然使用了插入件前馈系统,但依然存在扰动束流光学的残余四极场,它会导致束流横向振荡工作点的变化,进而影响机器的性能和同步辐射光亮度的稳定。为此,我们研发了一个工作点反馈系统来解决这个问题,并且已经在上海光源储存环上投入了运行,在两周左右的运行周期内,工作点的稳定度达到了±0.001。这个反馈系统还有另一个重要功能,即可以根据监控反馈系统校正电流的变化趋势来判断二极磁铁电源和四极磁铁电源是否存在慢漂问题。为了验证这个工作点反馈的可行性,我们对使用反馈前后几周的束流参数进行了比较,包括储存环注入效率、束流寿命、水平方向束斑尺寸以及β函数的变化情况（beta-beatings）。     

上海光源首批波荡器永磁块研制

介绍了上海光源2台混合型真空室内波荡器IVU25用636件Sm2Co17永磁块(规格为65 mm×25 mm×8.965 mm)和1台APPLE-Ⅱ型椭圆极化波荡器EPU100用668件NdFeB永磁块(规格为35 mm×35 mm×25 mm)的研制情况。指出了影响剩磁离散性、磁化偏角、机械尺寸精度等技术要求的基本因素,并对其原理进行了分析。研制的Sm2Co17和NdFeB永磁块的磁性能、磁场品质、机械尺寸精度等满足了上海光源首批波荡器插入件技术要求。     

上海光源首批波荡器永磁块研制

介绍了上海光源2台混合型真空室内波荡器IVU25用636件Sm2Co17sub>永磁块(规格为65 mm×25 mm×8.965 mm)和1台APPLE-Ⅱ型椭圆极化波荡器EPU100用668件NdFeB永磁块(规格为35 mm×35 mm×25 mm)的研制情况。指出了影响剩磁离散性、磁化偏角、机械尺寸精度等技术要求的基本因素,并对其原理进行了分析。研制的Sm2Co17sub>和NdFeB永磁块的磁性能、磁场品质、机械尺寸精度等满足了上海光源首批波荡器插入件技术要求。     

磁铁安装误差对束流轨道的影响

采用数值方法系统地分析了HLS储存环磁铁安装误差对束流闭轨的影响,发现造成闭轨畸变的主要原因是四极铁在横向位置的安装误差和二极铁在束流方向的旋转,并给出了它们的放大因子;同时对横向发射度的耦合进行了研究,发现造成垂直方向发射度增加的主要原因是闭轨畸变;在综合考虑各种误差的情况下,提出了需要对各种磁铁进行进一步准直的要求。     

上海光源储存环线性模型校正

上海光源是我国刚刚建成的一台第三代中能同步辐射光源。为使得上海光源能够严格工作在设计状态下, 在调试过程中进行了一系列线性模型的校正, 主要包括闭轨校正、 基于束流准直（BBA）校正、 LOCO参数校正和线性耦合校正。经过反复的线性模型校正以后, 上海光源储存环的闭轨畸变均方根误差在水平和垂直两个方向可以分别控制到50和60 μm的水平, 包络函数畸变和色散函数畸变都可以控制到小于1%的状态, 工作点和束流发射度基本上校正到了设计值。线性耦合校正能够方便地将储存环的耦合度从0.02%调节到2%左右。调试结果表明, 上海光源采取的这一套线性模型校正方法, 能够有效地将上海光源的工作状态校正到设计状态, 并且为其他模式的调节奠定了基础。In the commissioning stage of Shanghai Synchrotron Radiation Facility(SSRF) storage ring, several methods were used to correct the linear optics. Beam Based Alignment(BBA) was used for BPM\|Quadrupole offsets measurement; Response matrix was used for orbit correction; LOCO was used for linear optics fitting, and quadrupoles strength were adjusted to correction the beta function; coupling was measured and corrected by skew quadrupoles. After correction, closed orbit are reduced to 50/60 μm in hortizontal and vertical plane; β beating and dispersion errors are less than 1%; betatron tune and emmittance are closed to the design value; betatron coupling also can be adjusted from 0.02% to 2%. These methods have been proved to be useful for storage ring calibrations, with the help of these methods, SSRF storage ring can be tuned to the design model and other model easily.     

HEPS-TF低温波荡器低温系统设计

高能同步辐射光源验证装置(HEPS-TF)插入件系统计划研制一台基于镨铁硼的低温波荡器(CPMU)样机。低温波荡器的最大热负荷预计不超过700 W@80 K,要求低温系统冷却磁铁温度至85 K以下。低温波荡器低温系统采用过冷液氮闭循环迫流冷却的方式,对低温波荡器真空室内磁铁磁极阵列和真空内大梁进行冷却。根据热负荷估算情况,设计主循环流量为12 L/min,分为两条支路分布冷却低温波荡器内上下两排磁铁磁极阵列。根据循环流量对泵的热量、换热器换热能量、流经低温波荡器的液氮平均温度的影响,推导了液氮循环泵的调节策略。     

Coupling measurement and correction at the SSRF storage ring

Brightness is an important parameter for 3^rd generation light source. Correcting the emittance coupling is a realistic way to increase brightness without any additional equipment in a machine under operation. The main sources of emittance coupling are betatron coupling and vertical dispersion. At the SSRF storage ring, tune split and LOCO are used to measure the respective betatron and emittance coupling. Both of these sources can be corrected by skew quadrupoles. By measuring the skew quadrupole-coupling response matrix, betatron coupling can be changed from 0.014% to 2%. But the vertical dispersion changes at the same time. LOCO can find the suitable setting to correct simultaneously the betatron coupling and vertical dispersion. The emittance coupling can be reduced to 0.17% by this method. More simulations show the potential for smaller emittance coupling if more skew quadrupoles are employed.     

Studies of closed orbit correction and slow orbit feedback for the SSRF storage ring

Details of the active ways to suppress Closed Orbit Distortion (COD), including bending magnet sorting and survey and alignment of the magnets, are discussed based on the studies of affections to the COD by the bending magnet field error and the misalignment of quadrupoles. The closed orbit correction and the Slow Orbit Feed Back (SOFB) system for the SSRF storage ring are presented in this paper. With these available methods, better results were obtained during the commissioning period with 3 GeV beam energy.     

Studies of closed orbit correction and slow orbit feedback for the SSRF storage ring

Details of the active ways to suppress Closed Orbit Distortion （COD）, including bending magnet sorting and survey and alignment of the magnets, are discussed based on the studies of affections to the COD by the bending magnet field error and the misalignment of quadrupoles. The closed orbit correction and the Slow Orbit Feed Back （SOFB） system for the SSRF storage ring are presented in this paper. With these available methods, better results were obtained during the commissioning period with 3 GeV beam energy.     

Beam dynamics of the superconducting wiggler on the SSRF storage ring

In the SSRF Phase-II beamline project, a superconducting wiggler(SW) will be installed in the electron storage ring. It may greatly impact on the beam dynamics due to the very high magnetic field. The emittance growth becomes a major problem, even after correction of the beam optics. A local achromatic lattice is studied, in order to combat the emittance growth and keep the performance of the SSRF storage ring as high as possible. Other effects of the SW are also simulated and optimized, including the beta beating, the tune shift, the dynamic aperture, and the field error effects.     

Nonlinear optimization of the modern synchrotron radiation storage ring based on frequency map analysis

In this paper, we present a rule to improve the nonlinear solution with frequency map analysis (FMA), and without frequently revisiting the optimization algorithm. Two aspects of FMA are emphasized. The first one is the tune shift with amplitude, which can be used to improve the solution of harmonic sextupoles, and thus obtain a large dynamic aperture. The second one is the tune diffusion rate, which can be used to select a quiet tune. Application of these ideas is carried out in the storage ring of the Shanghai Synchrotron Radiation Facility (SSRF), and the detailed processes, as well as better solutions, are presented in this paper. Discussions about the nonlinear behaviors of off-momentum particles are also presented.     

上海光源储存环工作点测量系统

报道了工作点测量技术的研究现状,对束流频谱分析用于工作点测量的方法进行了详细说明。介绍了上海光源储存环工作点测量系统的物理需求、方案设计、硬件结构及关键设备选型。采用束流实验的方法对系统配置参数进行优化,对系统测量误差及分辨力进行测试评估,讨论了测量系统不同工作模式的优缺点,并给出加速器不同运行阶段应该采用的运行模式。优化后的上海光源工作点测量系统,其系统测量误差小于0.000 1,测量分辨力好于0.000 05,测量过程对束流轨道及等效束斑尺寸的扰动控制在μm量级,现已在上海光源运行及机器研究中投入实用。     

中国散裂中子源磁铁系统和样机研制

中国散裂中子源(China Spallation Neutron Source, CSNS)快循环同步加速器(Rapid Cycling Synchrotron, RCS)磁铁由24块二极磁铁、48块四极磁铁、16块六极磁铁和若干斜四极磁铁以及校正磁铁组成, 其中二极磁铁和四极磁铁是带直流偏置的25Hz正弦交流励磁, 铁芯和线圈导体将产生不可忽视的涡流效应. 为了积累批量生产磁铁的制造经验, 探索磁铁后期处理和磁场测量方法, 已完成了中空水冷铝绞线试样线圈的研制, 启动了二极磁铁和四极磁铁样机的研制. 本文将对相关进展进行介绍.     

Tune optimization of the third generation light source storage ring based on Frequency Map Analysis

Tune optimization is necessary to optimize the nonlinearity of the third generation light source storage ring. In this paper we summarize the common strategies for choosing a tune and discuss tune op-timization. Frequency Map Analysis (FMA) is applied as a tune scanning tool to reveal information about nonlinear resonances and guide the tune optimization. The Shanghai Synchrotron Radiation Facility (SSRF) storage ring is taken as a test lattice, and the optimum solutions are presented in this paper. Moreover, the third order regular structural resonances excited by sextupoles are particularly investigated, and it is found that these resonances distort the tune shifts with amplitude and show a stop-band like the linear structural resonances.