Continuous-wave optical parametric oscillator based on periodically poled KTiOPO(4)

We report what is to our knowledge the first demonstration of a continuous-wave optical parametric oscillator (OPO) based on periodically poled KTiOPO(4) . The 10-mm-long flux-grown crystal had a quasi-phase-matched period of 9mum . The pump source was a miniature frequency-doubled Nd:YAG laser, and the threshold power of this doubly resonant device was 51 mW. The OPO was operated near room temperature. The signal and the idler wavelengths could be tuned in the range 1037-1093 nm by variation of the crystal temperature (32-38 degrees C) and the cavity length. Unlike in other nonlinear crystals, green-induced infrared absorption was not observed up to the highest pumping intensity of approximately 4.5kW/cm(2) .     

Continuous-wave optical parametric oscillator based on periodically poled KTiOPO(4) and its application to spectroscopy

We report a continuous-wave, doubly resonant optical parametric oscillator (OPO) based on the nonlinear material periodically poled KTiOPO(4) and its application to spectroscopy. The OPO, which is pumped by a diode-pumped frequency-doubled Nd:YLF laser at 523 nm, has a low pump-power threshold of 25 mW and can deliver 10 mW of single-frequency output at 1.65 mum for a pump power of 200 mW. The idler wavelength can be temperature tuned at a rate of 0.73 nm/( degrees )C , and smooth tuning of the output frequency over ~3 GHz is achieved by smooth tuning of the pump laser. We demonstrate the practicality of the OPO by recording the absorption spectrum of methane near 1649 nm.     

Widely and continuously tunable optical parametric oscillator based on a cylindrical periodically poled KTiOPO(4) crystal

We report on what is to our knowledge the first realization of a quasi-phase-matched optical parametric oscillator (OPO) based on a crystal with a cylindrical shape. The main reason for interest in this device is its broad, continuous tuning. In experiments with a 1064-nm pump, the signal tuning range was equal to 525 nm (1515-2040 nm), and the corresponding idler was continuously tuned over 1340 nm (2220-3560 nm). The angular tuning was 26 degrees , with only a minor variation of the OPO threshold over the entire tuning range.     

Nanosecond optical parametric oscillator based on large-aperture periodically poled RbTiOAsO(4)

We report on optical parametric oscillators (OPO's) based on periodically poled RbTiOAsO(4) (PP RTA), which are pumped by Q -switched solid-state lasers. With a diode-pumped Nd:YVO(4) laser (pulse energy, 800microJ ; pulse duration, 5.5 ns; repetition rate, 1 kHz) the PP RTA OPO generated 1.58-microm signal and 3.26-microm idler radiation with a signal pulse energy of 45microJ . The large aperture of 3 mmx3 mm of the PP RTA crystal also permitted OPO operation with pump pulse energies as high as 65 mJ, provided by a flash-lamp-pumped Q -switched Nd:YAG laser (pulse duration, 20 ns; repetition rate, 10 Hz). With this pump source the OPO generated signal pulse energies as high as 17 mJ, corresponding to an efficiency of 26%. The performance of this OPO shows that large-aperture PP RTA crystals are well suited for pulsed nanosecond OPO operation with pump pulse energies of tens of millijoules.     

High-power optical parametric oscillation in large-aperture periodically poled KTiOPO(4)

Electric field poling has been employed to fabricate 3-mm-thick periodically poled KTiOPO>(4) crystal for a high-power optical parametric oscillator. The maximum output power of the singly resonant optical parametric oscillator reached 13 mJ with 45% efficiency when the resonator was pumped with a 2.2-mm-diameter beam from a Q-switched Nd:YAG laser. The influence of the cavity design on the spectral and spatial qualities of the output parametric radiation is also discussed.     

Singly resonant optical parametric oscillator in periodically poled KTiOPO(4) pumped by a Bessel beam

Conical pumping was used in a periodically poled KTiOPO(4) optical parametric oscillator for singly resonant idler generation in a nearly diffraction-limited axial beam. A single signal-idler pair was generated over the whole tuning range by use of asymmetric reflectivity of the OPO mirrors. Pump depletion of 40% and total conversion efficiency of 27% were obtained. Additional OPO tuning capability was demonstrated by adjustment of the angle of the conical pump beam.     

Efficient femtosecond traveling-wave optical parametric amplification in periodically poled KTiOPO(4)

We report, for the first time to our knowledge, high-power femtosecond traveling-wave optical parametric amplification by use of periodically poled KTiOPO(4) . With a single pass through a 4-mm-long sample of 1.23-mm thickness we achieved 40% internal conversion efficiency and 5microJ of single-pulse idler energy near 3.8microm , using only 75microJ of energy from the output of a conventional 1-kHz Ti:sapphire regenerative amplifier. The 210-fs-long idler pulses were almost transform limited. We discuss the specific problems encountered in high-power parametric conversion, such as unwanted quasi-phase-matched upconversion processes for polarization configurations that utilize the largest (d(33)) nonlinear coefficient and the related formation of color centers (gray tracking) in KTiOPO(4) .     

Continuous-wave singly resonant optical parametric oscillator based on periodically poled RbTiOAsO(4)

We report a continuous-wave optical parametric oscillator (OPO) based on periodically poled RbTiOAsO(4) (PPRTA). The singly resonant OPO, which is located within a Ti:sapphire laser, has a high-finesse signal cavity and delivers a maximum output power of 270 mW to the nonresonant idler wave at 2.92mum , through a 4.5-mm PPRTA crystal. For room-temperature operation and a crystal with a 30-mu;m grating period, pump tuning over 838-848 nm results in OPO tuning over 1.13-1.27mum (signal) and 2.53-3.26mum (idler), limited by the bandwidth of optical coatings. PPRTA exhibits thermal properties superior to those of periodically poled LiNbO(3) .     

Temperature-tunable nanosecond optical parametric oscillator based on periodically poled

We report a compact quasi-phase-matched optical parametric oscillator (OPO) using periodically poled MgO-doped LiNbO₃ with different grating periods. The OPO is pumped by a diode-pumped passively Q-switched Nd:YAG laser providing 4.8-ns pulses at 5.4-kHz repetition rate. The OPO generates signal and idler wavelengths tunable in the ranges of 1.5– and 2.8–, respectively, by changing the crystal temperature between room temperature and . The temperature-dependent Sellmeier equation for the extraordinary refractive index of MgO-doped LiNbO₃ is modified in the Mid-IR region, which gives an accurate prediction of the experimental temperature-tuning results. The linewidth of the signal wave is in the range of 0.5–1.0 nm without any controlling element.     

Near- to mid-infrared picosecond optical parametric oscillator based on periodically poled RbTiOAsO(4)

We describe a Ti:sapphire-pumped picosecond optical parametric oscillator based on periodically poled RbTiOAsO(4) that is broadly tunable in the near to mid infrared. A 4.5-mm single-grating crystal at room temperature in combination with pump wavelength tuning provided access to a continuous-tuning range from 3.35 to 5microm , and a pump power threshold of 90 mW was measured. Average mid-infrared output powers in excess of 100 mW and total output powers of 400 mW in ~1-ps pulses were obtained at 33% extraction efficiency.     

Broadly tunable infrared femtosecond optical parametric oscillator based on periodically poled RbTiOAsO(4)

We present results from what we believe is the first reported example of an optical parametric oscillator based on periodically poled RbTiOAsO(4). The oscillator is pumped by a femtosecond self-mode-locked Ti:sapphire laser and, with a single-grating 2-mm-long crystal and one mirror set, a combination of pump and cavity-length tuning provided wavelength coverage from 1060 to 1225nm (signal) and 2.67 to 4.5 microm (idler). Average output powers were as much as 120mW in the signal and 105mW in the idler and interferometric autocorrelations recorded at signal and idler wavelengths of 1.1 and 3.26 microm, respectively, imply pulse durations of 125 and 115fs, respectively.     

Ultrabroad gain in an optical parametric generator with periodically poled KTiOPO4

An optical parametric gain bandwidth of 115 THz at full-width half maximum is generated from a picosecond Ti:sapphire pumped degenerate optical parametric generator. This ultrabroad bandwidth could be obtained by first identifying the wavelength where the nonlinear optical material has zero group-velocity dispersion (GVD). By pumping at half this wavelength the degenerate signal–idler pairs can accommodate ultrabroad bandwidths. The explanation for this is that the group velocities of the signal and the idlers are approximately matched and the GVD is small. However, in order to thoroughly investigate the degeneracy region around 1700 nm we fabricated several periodically poled KTiOPO₄ (PPKTP) crystals with different periods, and also one periodically poled RbTiOPO₄ (PPRTP). Both collinear and noncollinear configurations were employed for broadband parametric generation in this region. It was found that the optimum pump wavelength is in the region between 800 nm to 850 nm for PPKTP, and we could also conclude that a similar performance was found for PPRTP. This work will allow the design of optical parametric devices for generating few-cycle pulses in the spectral region between 1.1 μm and 3.8 μm. PACS 42.65.Re; 42.65.Ky; 42.65.-k     

High-power picosecond optical parametric oscillator based on periodically poled lithium niobate

A high-power picosecond optical parametric oscillator (OPO) based on a 47-mm periodically poled lithium niobate crystal is described. More than 12 W of total average power-almost 8 W of signal power at 1.85 microm and more than 4 W of idler radiation at 2.5 microm -is simultaneously extracted from less than 18 W of average pump power. The OPO is synchronously pumped by 80-ps (FWHM) cw mode-locked pulses at 1.064 microm , and its output is tunable from 1.7 to 2.84microm . Nearly transform-limited signal pulses are obtained following the introduction of two intracavity etalons.     

Angle-tuned signal-resonated optical parametric oscillator based on periodically poled lithium niobate

We demonstrate an angle-tuned signal-resonated optical parametric oscillator (OPO) with periodically poled lithium niobate (PPLN) pumped by a diode-pumped Nd:YVO4 laser. 1499.8 - 1506.6 nm of signal wavelength is achieved at 140℃ by rotating a 29-μm period PPLN from 0° - 10.22° in the x-y plane while keeping the pump wave vertical to the resonator mirrors. Two pairs of the signal and idler waves of the same wavelengths can be achieved symmetrically for each pair of angles of rotation with same absolute value and opposite sign. Theoretical analyses on angle-tuned PPLN-OPO with pump wave vertical to the resonator mirrors are presented and in good agreement with our experimental results. It is also found that all interacting waves in the cavity (not inside the crystal) are always collineax for PPLN-OPO with the pump wave vertical to the resonator mirrors while phase-matching is noncollinear within the crystal.     

Picosecond Ti:sapphire-pumped optical parametric oscillator based on periodically poled LiNbO(3)

Periodically poled lithium niobate has been used in a singly resonant optical parametric oscillator pumped by a cw mode-locked Ti:sapphire laser. A tuning range of 1.15 to 2.4 microm was achieved when the pump was tuned, and this range was limited only by the mirror reflection bandwidth. Thresholds as low as 18 mW and an overall slope efficiency of 44% were observed, with average output powers of 130 mW (70 mW) for the signal (idler).     

Frequency-agile kilohertz repetition-rate optical parametric oscillator based on periodically poled lithium niobate

We report kilohertz repetition-rate pulse-to-pulse wavelength tuning from 3.22 to 3.7 mum in a periodically poled lithium niobate (PPLN) optical parametric oscillator (OPO). Rapid tuning over 400 cm(-1) with random wavelength accessibility is achieved by rotation of the pump beam angle by no more than 24 mrad in the PPLN crystal by use of an acousto-optic beam deflector. Over the entire tuning range, a near-transform-limited OPO bandwidth can be obtained by means of injection seeding with a single-frequency 1.5-mum laser diode. The frequency agility, high repetition rate, and narrow bandwidth of this mid-IR PPLN OPO make it well suited as a lidar transmitter source.     

Broadband nondegenerate optical parametric amplification in the mid infrared with periodically poled KTiOPO4

We theoretically and experimentally demonstrate that the bandwidth in a nondegenerate optical parametric amplifier can be substantially increased by noncollinear interaction in a quasi-phase-matched single-periodicity structure. Broadband amplification of signals between 1540 and 1720 nm was realized in periodically poled KTiOPO4. The achieved signal bandwidth of 6.9 THz at 1680 nm is large enough to accommodate sub-100 fs optical pulses.     

Green-pumped high-power optical parametric oscillator based on periodically poled MgO-doped stoichiometric LiTaO3

A high-power 532 nm-pumped multikilohertz nanosecond optical parametric oscillator using a periodically poled 1.0 mol.% MgO-doped stoichiometric lithium tantalate crystal that could be operated from room temperature to 200 degrees C without damage is reported. A broad continuous tuning range from 855 to 1410 nm was achieved within a single domain period. Efficient operation of high peak power and watt level average power with a power conversion of 62.5% was measured. These results show that a high-resolution high average power visible tunable source can be realized.     

Diode-pumped continuous-wave widely tunable optical parametric oscillator based on periodically poled lithium tantalate

We report on a diode-laser pumped cw optical parametric oscillator (OPO) based on quasi-phase-matched periodically poled lithium tantalate. Pumped by the 2.3-W single-frequency, nearly diffraction-limited 925-nm output of an InGaAs diode master-oscillator power amplifier, the pump and signal resonant OPO generates a single-frequency idler wave with an output of as much as 244 mW. The wavelengths of the signal and idler waves are widely tunable in the range 1.55-2.3mum by use of different poling periods (27.3 to 27.9mum) and by variation of the crystal temperature in the range 70-190 degrees C.