Effect of temperature on the stress-strain behavior of a polypropylene-particulate rubber composite

Composites based on polypropylene and rubber particles were studied at different temperatures. It was found that, as the temperature is elevated, the type of defects that are formed near large filler particles changes from a crack to a diamond-shaped void and, next, to an elliptical or slit-type void. The change in the defect type predetermines the change of the composite failure mechanism at a constant particulate-filler content from brittle fracture before the yield point to fracture during neck formation or propagation and, finally, to non-uniform plastic drawing with a stable neck growth.     

The effect of cold rolling on crack propagation behavior in high-density polyethylene

Crack propagation behavior in HDPE was studied. The preliminary orientation of the polymer, which is deformed in its isotropic state via necking and breaks down at the neck propagation stage, improves the crack resistance and ductility of the material. The critical crack opening in preoriented HDPE samples dramatically increases at relatively low draw ratios of cold rolling while the speed of transverse crack propagation decreases.     

Reactively compatibilized and dynamically vulcanized thermoplastic elastomers based on high-density polyethylene and reclaimed rubber

Melt blending was employed to prepare thermoplastic elastomer (TPE) of reclaimed rubber (RR) and high density polyethylene (HDPE). Mechanical properties of TPE samples were improved in different methods including dynamic vulcanization and reactive blending (reactive compatibilization) during melt mixing in an internal Haake mixer. The physical and mechanical properties of the TPE blends were investigated by the dynamic mechanical analysis (DMA) and tensile tests. The thermal behavior was characterized by differential scanning calorimeter (DSC) and thermogravimetric analysis (TGA). The phase morphology of the blends was studied by scanning electron microscopy (SEM). Experimental results showed that, both static and dynamic mechanical properties of reactively-compatibilized and dynamically-vulcanized samples improved significantly compared with the virgin samples. The effect of dynamic-vulcanization and reactivecompatibilization on the mechanical properties revealed that the Young’s modulus and storage modulus increased with both improvement methods. SEM results showed that, dynamic-vulcanization and reactivecompatibilization methods improved the distribution of RR particles in HDPE matrix. Although both methods improved the thermal and mechanical properties of the HDPE/RR blends, dynamic-vulcanization was more effective and promising approach due to the higher properties of HDPE/RR blends prepared by this method.     

On the fracture of composites based on ultrahigh-molecular-weight polyethylene and fine aluminum particles

Mechanical characteristics of polymerization filled composite materials based on ultrahigh-molecular-weight polyethylene and fine aluminum particles are studied. The prepared composites preserve their ability for high plastic deformations even when the volume filler content is φ = 0.57. For the tensile drawing of the composite material with randomly distributed particles, an equation describing the dependence of breaking stress on the volume filler content is derived. For the model of the composite with regularly ordered particles, the Nielsen equation is the approximation of the equation proposed in this work for a material with randomly distributed particles.     

Deformation behavior of composites based on low-density polyethylene and hollow glass spheres

The mechanical properties of composites of low-density polyethylene with hard particles were examined.     

Importance of temperature effect on the electrophoretic behavior of charge-regulated particles

The Joule heating effect is inevitable in electrophoresis operations. To assess its influence on the performance of electrophoresis, we consider the case of a charge-regulated particle in a solution containing multiple ionic species at temperatures ranging from 298 to 308 K. Using an aqueous SiO(2) dispersion as an example, we show that an increase in the temperature leads to a decrease in both the dielectric constant and the viscosity of the liquid phase, and an increase in both the diffusivity of ions and the particle surface potential. For a particle having a constant surface potential, its electrophoretic mobility is most influenced by the variation in the liquid viscosity as the temperature varies, but for a charged-regulated particle both the liquid viscosity and the surface potential can play an important role. Depending upon the level of pH, the degree of increase in the mobility can be on the order of 40% for a 5 K increase in the temperature. The presence of double-layer polarization, which is significant when the surface potential is sufficiently high, has the effect of inhibiting that increase in the mobility. This implies that the influence of the temperature on the mobility of the particle is most significant when the pH is close to the point of zero charge.     

The influence of nano silica particles on gamma-irradiation ageing of elastomers based on chlorosulphonated polyethylene and acrylonitrile butadiene rubber

The goal of this work was to study gamma irradiation ageing of rubber blends based on acrylonitrile butadiene rubber (NBR) and chlorosulphonated polyethylene rubber (CSM) reinforced by silica nano particles. The NBR/CSM compounds (50: 50, w/w) filled with different content of filler (0–100 phr) were crosslinked by sulfur. The vulcanization characteristics were assessed using the rheometer with an oscillating disk. The vulcanizates were prepared in a hydraulic press. The obtained materials were exposed to the different irradiation doses (100, 200, 300 and 400 kGy). The mechanical properties (hardness, modulus at 100% elongation, tensile strength and elongation at break) and swelling numbers were assessed before and after gamma irradiation ageing.     

Non-isothermal crystallization kinetics of graphite-reinforced crosslinked high-density polyethylene composites

Journal of Thermal Analysis and Calorimetry - Crosslinked high-density polyethylene (PEX) composites containing various amounts of graphite particles (1, 2.5 and 5 mass% or 0.479, 1.206 and 2.445...     

The electrical properties of schungite-containing compositions based on polypropylene and high-density polyethylene

Variations in the dc and ac conductivities of schungite-containing compositions based on polypropylene-high-density polyethylene (PP-PE) blends were studied depending on the composition of the polymeric blend, the volume concentration of the filler, and the order of the introduction of the composition components during the preparation of compositions. It was shown that the conductivities of the compositions could depend on the order of the introduction of the components. The structure of initial and schungite-containing PP-PE blends of different compositions was studied by atomic-force microscopy. It was shown that the structure of the compositions depended on the composition of the initial PP-PE blends and the order of the introduction of the components into schungite-filled PP-PE compositions.     

Dispersing behavior of recycled rubber particles

The hydrophobic nature of recycled rubber particles presently limits their use only in non-aqueous media. Recycled rubber particles were chemically modified by preparation of amphiphilic semi-interpenetrating polymer networks using poly(acrylic acid) as the hydrophilic polymer. The resulting composite particles are water dispersible and suitable for various aqueous media applications.     

The effect of post-irradiation annealing on the crosslinking of high-density polyethylene induced by gamma-radiation

Samples of two high-density polyethylenes having different crystallinity levels were gamma irradiated under vacuum at doses ranging from 20 to 300 kGy. Subsequently, the vials containing the irradiated samples were exposed to different post-irradiation treatments. Parts of the specimens were annealed while still under vacuum. The annealing time was 4 h and the annealing temperatures 110 °C or 150 °C. Others were exposed directly to air opening the vials without any thermal treatment. It was verified that in all cases the dosage to produce an incipient gel increases with the crystallinity of the initial sample. The amount of gel produced after exposing specimens of the same polymer to a given dose increases with the annealing temperature. The largest increment in the amount of gel produced at the completion of the post-irradiation treatment was found on the samples with the highest initial crystallinity level.Evidence of oxidation was found in all irradiated samples. The extent of oxidation depends on the initial crystallinity of the sample, the irradiation dose and the type of post-irradiation treatment. The heat of fusion measured in the annealed samples decreases with the gel content while the fusion temperature was slightly affected. Ductile or brittle behaviors were observed after testing specimens under tensile stress. The yield stress increases proportionally to the crystallinity level that, in turn, depends on the total dosage applied to the samples. The extensibility of ductile samples is determined by the amount of gel produced regardless of the degree of initial crystallinity and the type of annealing process applied to each sample.     

The effect of hindered amine light stabilizers on the photooxidative stability of high-density polyethylene

The photoprotective effectiveness of various polymeric and nonpolymeric hindered amine light stabilizers (HALS) was determined by exposing samples of high-density polyethylene (HDPE) containing these additives to ultraviolet (UV) light and measuring the resultant oxygen uptake characteristics. Values of the initial quantum yield for oxygen uptake calculated for these formulations indicate that the higher molecular weight HALS compounds are less effective photostabilizers than the nonpolymeric HALS, and this is partly attributable to their decreased mobility in the polymer matrix. It was further found that the addition of an ultraviolet absorber (UVA) to a formulation containing a polymeric HALS compound enhances its photostability, although this phenomenon may be partly due to synergism between the UVA and the antioxidant, the latter having been added as part of the base stabilization. The antagonism which exists between certain sulfur-containing antioxidants and HALS compounds was also investigated and it was found that the lower molecular weight sulfur-containing antioxidants exhibit the greatest degree of antagonism. The results confirm that the mobility in the polymer matrix of the stabilizer system can serve as an explanation of its effectiveness. The article provides evidence that the technique of oxygen uptake monitoring is a sensitive and rapid method of assessment of polymer photostability in the presence of stabilizer systems.     

Influence of the properties of the matrix polymer on the strain characteristics of dispersion-filled composites based on polyethylene and crumb rubber

Mechanical properties of highly filled composites based on polyethylene of various grades and crumb based on ethylene-propylene-diene rubber were studied. The influence of the crack resistance of the matrix polymer on the strain properties of rubber-reinforced plastics was considered. A scheme of failure of highly filled composites with the deformable filler was suggested.     

Reversible and irreversible crystallization in high-density polyethylene at low temperature

Reversible and irreversible crystallization and melting of high-density polyethylene at low temperature has been re-evaluated and is discussed in terms of the concept of the specific reversibility of a crystal. The concept of the specific reversibility links reversible and irreversible melting of a specific crystal such that reversible melting occurs only at slightly lower temperature than irreversible melting. In this study evidence for irreversible crystallization at low temperature in high-density polyethylene is provided, non-avoidable by primary crystallization and extended annealing at high temperature. The simultaneously observed reversible crystallization and melting at low temperature can be attributed to lateral-crystal-surface activity in addition to the well-established reversible fold-surface melting, dominant at high temperature, and evidenced by small-angle X-ray data available in the literature. This revised version was published online in August 2006 with corrections to the Cover Date.     

The effect of low-temperature crystallization on the mechanical behavior of rubber

In cold climates the correct performance of rubber components such as seismic isolators depends on them maintaining their elastic properties when exposed to prolonged periods at low temperatures. The high damping compounds developed for seismic isolation are normally especially prone to crystallization when exposed to subzero temperatures for periods of a few weeks. The effect of low-temperature crystallization on the mechanical stiffening of natural rubber is evaluated. The relationship between the shear modulus and amount of crystallization is measured using a technique in which the dimensional change and stiffness are monitored simultaneously. The relationship is found to be approximately independent of the crosslink density and the temperature of crystallization. It appears not to be realistically modeled by considering the crystals to behave as rigid filler particles but good qualitative agreement with experiment was obtained by modeling the crystals as a network of threads. Partially crystalline rubbers are found to yield under the application of a large stress like other partially crystalline polymers. Mechanisms for suppressing crystallization in rubber are discussed and the low-temperature stiffening of specially formulated rubber compounds for seismic isolation is presented. These results show that carefully formulated high damping natural rubber compounds can give adequate performance at low temperatures. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2181–2190, 2004     

New polymer composites based on keratin and polyethylene

New biodegradable composites based on keratin and polyethylene have been produced under shear deformation. It has been demonstrated that the introduction of keratin leads to an increase in elastic modulus and to a decrease in ultimate tensile strength and elongation at break of the compositions. Elongation at break ε_b depends on the keratin dispersity; the highest ε_b values are observed for the compositions containing the smallest keratin particles. It has been shown that the compositions are susceptible to mold fungi; i.e., they are biodegradable.     

Mechanical properties and crystallization of high-density polyethylene composites with mesostructured cellular silica foam

In this study, composites of high-density polyethylene (HDPE) with mesostructured cellular foam (MCF) silicas have been prepared by melt mixing and studied for the first time. Two different MCF silica analogues having different pore size were used, i.e., 12 nm (MCF-12) and 50 nm (MCF-50). The MCF content in the mesocomposites was 1, 2.5, 5, and 10 mass%. All HDPE/MCF-50 mesocomposites exhibited improved mechanical properties compared with neat HDPE, indicating that the mesocellular silica foam particles with the large mesopore size can act as efficient reinforcing agents. On the other hand, the MCF-12 silica with the smaller size mesopores induced inferior mechanical properties, mainly due to the poorer dispersion of the silica particles and the formation of large aggregates. The mesocellular silica foam particles also affected the thermal properties and the crystallization characteristics of HDPE. Crystallization of mesocomposites was faster than that of neat HDPE. Crystallization kinetics was analyzed with the Avrami equation for both isothermal and non-isothermal conditions. For isothermal crystallization, the Avrami exponent increased with increasing crystallization temperature from 2 to 3. In non-isothermal crystallization, the values of the Avrami exponent increased from 3 to 6.3 with decreasing cooling rate. Lower activation energy values of non-isothermal crystallization were calculated using the isoconversional method of Friedman, as well as using the Kissinger’s equation. Finally, the nucleation efficiency of the mesocellular silica foam particles was estimated from data associated with non-isothermal crystallization, according to the method of Dobreva.     

The thermal stability of highly filled high-density polyethylene quaternary composites: Interactive effects and improved measures

A range of formulations — consisting of high-density polyethylene, surface-coated calcium carbonate, masterbatched carbon black and a stabiliser package — were compared in terms of their thermal stability through the use of several techniques and measures. Notably, calcium carbonate loadings of up to 60 wt% were investigated. The formulations were designed to be I- and D-optimal, based on a quadratic Scheffé polynomial model. Novel and established measures for the thermal stability of the materials were compared, based on data generated using techniques for the determination of oxidative induction time and for studies by time-sweep oscillatory rheometry. For ease of comparison, all tests were performed in air. Fourier-transform infrared spectroscopy was performed on the materials subjected to time-sweep oscillatory rheometry, to ascertain the locality and modes of degradation. Variable effects were found, depending on the technique used. Broadly, strong primary effects were found: positive in the cases of the carbon black and stabiliser pack, negative in the case of calcium carbonate. The latter, however, was offset by the highly synergistic interaction of calcium carbonate with the stabiliser pack. Time-sweep oscillatory rheometry was shown to be a promising method, with it yielding high-quality, comparable results when interpreted using a novel measure.