基于拮抗作用检测除草剂的类囊体膜生物传感器研究

利用除草剂对植物类囊体束缚酶分解过氧化氢的拮抗作用,研制了一种快速检测痕量除草剂的电化学生物传感器.将植物类囊体用聚乙烯醇-苯乙烯吡啶(PVA-SbQ)光敏聚合剂在紫外光诱导下产生大分子网状结构进行包埋,制成生物敏感膜,并固定在铂电极表面.根据加入除草剂时类囊体膜束缚酶分解过氧化氢活性的变化,对除草剂进行测定.在含有1×10^-3mol/LNaCl,5×10^-3mol/LMgCl₂和0.01mol/LH₂O₂的Tris-HCl缓冲溶液(pH=7.4)中,基于测量0.65V处H₂O₂氧化电流的变化,可以对下列浓度的除草剂进行定量检测:百草枯3×10^-9～1.5×10^-7mol/L,敌草龙1×10^-8～3×10^-7mol/L,扑草净4×10^-8～3×10^-6mol/L,阿特拉津1×10^-7～5×10^-6mol/L,莠灭净1×10^-7～5×10^-6mol/L.利用PVA-SbQ光聚合膜固定类囊体,能够使酶的活性在低温下保持数月.     

一种新的流动注射电化学发光分析方法及硫离子的分析测定研究

设计了一种用于流通体系的电解池,并以恒电流电解法与流动注射技术相结合,在线定量电解产生不稳定试剂次溴酸根,使其浓度和反应活性得以在线控制,稳定地应用于化学发光分析.在此基础上,研究了BrO^-在pH=9.60Na₂CO₃-NaHCO₃缓冲介质中氧化鲁米诺弱化学发光反应的分析特性,并基于硫离子对该弱化学发光反应体系的发光强度的增敏作用,建立了一种新的测定S^2-的流动注射电化学发光分析法.采用该方法测定S^2-的线性范围为3.10×10^-7～9.30×10^-5mol/L,检出限为1.00×10^-7mol/L,相对标准偏差为2%[n=11,c(S^2-)=3.10×10^-6mol/L]     

毛细管区带电泳电化学检测法测定药物及果汁中芦丁和L-抗坏血酸

用毛细管区带电泳-电化学检测法同时测定复方芦丁片及果汁中芦丁和L-抗坏血酸的含量.研究了电极电位、电解液浓度和酸度、电泳电压及进样时间等对电泳的影响,得到了较为优化的测定条件.以直径为300μm的碳圆盘电极为检测电极,电极电位为1.0V(vs.SCE),在25mmol/L硼砂-50mmol/LNaH₂PO₄(pH8.0)运行缓冲液中,上述两组分在12min内完全分离.芦丁和L-抗坏血酸浓度分别在1.0×10^-6～2.5×10^-4和5.0×10^-6～2.5×10^-3mol/L范围内与电泳峰电流呈现良好线性关系,检测下限分别为8.0×10^-7和3.3×10^-6mol/L.9次测定含5.0×10^-5mol/L芦丁和2.5×10^-4mol/LL-抗坏血酸的试样溶液,峰高的相对标准偏差分别为2.85%和1.65%,5次测得的平均回收率分别为97.73%和99.68%.     

溶胶-凝胶法固定胆固醇氧化酶偶联普鲁士蓝化学修饰电极的研究

用溶胶-凝胶法将胆固醇氧化酶固定在普鲁士蓝修饰的玻碳电极表面,制成了一种新型胆固醇传感器,实现了低电位下对胆固醇的间接测定,胆固醇的测定范围伏安法为5×10^-7～8×10^-5mol/L,安培法为5×10^-6～5×10^-4mol/L.伏安法检出限为1.2×10^-7mol/L,是目前所见灵敏度最高的胆固醇传感器之一,该传感器对胆固醇的测定可避免常规电化学传感器测定中由于样品中大量存在的易氧化物质所带来的干扰,该传感器的寿命长,使用次数在300次以上.     

镓-水杨基荧光酮伏安络合吸附波的研究

在pH为3.0的0.2mol/L邻苯二甲酸氢钾-HCI和5.0×10^-6mol/L水杨基荧光酮底液中,线性扫描可得灵敏的Ga-SAF络合物吸附波,峰电位为-0.93V(vsSCE).镓在7.5×10^-9～3.8×10^-7mol/L浓度范围内与峰高成正比关系.     

痕量多巴酚丁胺在碳糊电极上的吸附伏安行为及其痕量测定的研究

在0.1mol/L H₂SO₄底液中,用碳糊电极吸附伏安法测定多巴酚丁胺,阳极峰电位为0.46V(υS.SCE),峰电流与多巴酚丁胺的浓度在3.0×10^-9～1.0×10^-6mol/L范围内呈良好的线性关系.该法检测下限为1.5×10^-9mol/L,回收范围为94.00%～102.59%,相对标准偏差为3.1%(n=9).本文还对反应机理进行了初步探讨.     

碳点对鲁米诺电化学发光体系抑制作用的研究及其在DNA分析中的应用

发现碳点对鲁米诺电化学发光体系有明显的抑制作用, 并且由于碳点对单双链DNA的吸附性差异, 与单双链结合的碳点对鲁米诺电化学发光体系的抑制程度不同, 基于此实现了对DNA的快速、简便、灵敏的检测. 考察了碳点粒径、浓度对鲁米诺电化学发光体系的抑制行为的影响. 优化了溶液pH值, 鲁米诺浓度等电化学发光条件. 在优化的最佳实验条件下, 该方法检测DNA的线性范围为1.0×10^-10～7.5×10^-9 mol/L, 检出限为5.2×10^-11 mol/L.     

功能化纳米金放大的DNA电化学传感器研究

研究了DNA夹心杂交和直接杂交体系,将功能化纳米金引入到标记有生物素的杂交双链上,制成具有电化学活性和纳米金放大作用的DNA电化学传感器,采用循环伏安法测试.在夹心杂交体系中,靶点DNA浓度与阳极峰电流关系曲线的相对标准偏差为3.0%～13.0%,在浓度为6.9×10^-3～0.14nmol/L范围内得到良好的线性关系,检测限达到2.0×10^-3nmol/L,实现了对单碱基突变的高灵敏检测和序列识别.直接杂交检测限为2.5×10^-4mol/L,分别在2.5×10^-4～5.0×10^-3nmol/L和5.0×10^-3～10nmol/L范围内得到峰电量与浓度的良好线性关系.并比较这两种体系.     

儿茶酚胺衍生物与DNA之间相互作用的光谱和电化学法研究

用光谱和电化学方法研究了儿茶酚胺衍生物与小牛胸腺DNA之间的作用机制.结果表明,低浓度的多巴酚丁胺和肾上腺素与DNA之间主要为静电作用;而在高浓度时,则主要为插入作用.对于多巴胺,在5.00×10^-5～9.00×10^-4mol/L范围内,它与DNA之间主要为插入作用.同时,采用电化学方法测得多巴胺、肾上腺素和多巴酚丁胺与DNA之间的表观结合常数分别为1.55×10³,9.77×10³和1.74×10⁴L/mol.     

聚茜素红膜修饰电极控制电位扫描法分别测定多巴胺和抗坏血酸

研究了聚茜素红膜修饰电极(PARE)的制备及其对多巴胺(DA)和抗坏血酸(AA)的电催化性能,结果表明,在PARE上DA和AA具有不同的循环伏安行为,前者表现为一个准可逆过程,后者则为不可逆过程,并且二者的氧化峰电位分开近200mV.因此可通过控制不同的电位范围进行分步扫描,实现了对同一体系中DA和AA的分别测定,DA的还原峰电流和AA的氧化峰电流分别在8.0×10^-6～4.0×10^-3mol/L和4.0×10^-5～2.0×10^-2mol/L范围内与各自的浓度呈线性关系;检测限分别为8.0×10^-7mol/L和1.0×10^-5mol/L.同时与导数伏安法一步测定进行比较,结果令人满意.     

Flow-injection electrogenerated chemiluminescence detection of hydrazine based on its in-situ electrochemical modification at a pre-anodized platinum electrode

In this paper. it was found that the enhancing effect of hydrazine on the weak electrogenerated chemiluminescence (ECL) signal of the electrooxidation of luminol at a pre-anodized platinum electrode was stronger than that of hydrazine at a bare platinum electrode. Based on this finding and the combination of this finding with a flow-injection technique, a novel, sensitive and selective ECL method for hydrazine was developed. Under the optimum experimental conditions, the relative ECL intensity was linear with hydrazine concentration over the range 2.0 x 10(-8) - 5.0 x 10(-5) mol L(-1), with a detection limit of 6.0 x 10(-9) mol L(-1).     

Highly Sensitive Electrogenerated Chemiluminescence Detecting Ranitidine Based On Chemically Modifying Microenvironment of the Chemiluminescence Reaction

Using a graphite electrode modified with vaseline and NiO, ranitidine showed a strongly ECL enhancing effect for the weak ECL signal of electrooxidation of luminol. Based on this finding, a more sensitive ECL method for ranitidine was firstly proposed. Under the optimum experimental conditions, the ranitidine hydrochloride concentration in the range of 3.0×10^?8–9.0×10^?6 mol/L was proportional to the enhancing ECL signal and offered a 9×10^?9 mol/L detection limit for ranitidine hydrochloride. At the same time, based on the investigation on this ECL reaction mechanism, a new concept, to improve the suitable ECL reaction micro‐environment with chemically modified electrode technique for the better analytical performances of ECL analysis was also firstly proposed.     

Co-immobilization of polymeric luminol,iron(II) tris(5-aminophenanthroline) and glucose oxidase at an electrode surface,and its application as a glucose optrode

The anodic polymerization of 3-aminophthalhydrazide (luminol) and iron(II) tris 5-aminophenanthroline (Fe(phen-NH2)3(2+)) has been reported in this paper. A bilayer electrode was developed based on these polymers and the ITO conductive glass (denoted ITO[Fe(phen-NH2)3(2+)]luminol electrode). This electrode emitted light (lambdaem: 430 nm) as it was brought into contact with H2O2. At pH 10, the resulting electrochemiluminescence (ECL) showed a linear relationship with the concentration of H2O2 in the range of 10 microM(-1) mM. This bilayer electrode also showed an application potential for the detection of glucose after being further modified with glucose oxidase (denoted ITO[Fe(phen-NH2)3(2+)]luminol]GOx electrode). Although the resulting ECL decayed more rapidly in concentrated glucose solutions (e.g., I M) because of the consumption of luminol during use, the decay became less severe in diluted glucose solutions (e.g., 10 mM). According to the flow injection analysis, a linear relationship existed between the ECL and the concentration of glucose from 10(-5)-10(-3) M at pH 9. The detection limit could reach a level of 5 x 10(-5) M at this pH.     

Electrocatalytic oxidation of methanol on Ni modified polyaniline electrode in alkaline medium

Electrolytically deposited Ni on polyaniline film covered carbon paste electrode (Ni/PANI/CPE) was used as anode for the electrooxidation of methanol in alkaline medium. The electrochemical behavior and electrocatalytic activity of the electrode were studied using cyclic voltammetry, impedance spectroscopy, chronomethods, and polarization studies. The morphology and composition of the modified film were obtained using scanning electron microscope and energy dispersive X-ray analysis techniques. The electrooxidation of methanol in NaOH was found to be more efficient on Ni/PANI/CPE than on bare Ni, electrodeposited Ni on Pt, Ni on glassy carbon, and Ni on CPE substrates. Partial chemical displacement of dispersed Ni on PANI with Pt or Pd further improved its performance towards methanol oxidation.     

Development of new potentiometric sensors for the determination of proguanil hydrochloride in serum and urine

Potentiometric electrodes were developed for the rapid determination of proguanil hydrochloride in pure samples, pharmaceutical preparations and spiked serum and urine samples using PVC membrane,screen printed(SPE), coated wired(CWE), carbon paste(CPE) and modified carbon paste(MCPE)electrodes based on the ion-exchanger of proguanil with phosphotungestic acid(Pr-PT) as a chemical modifier. The prepared electrodes showed Nernestian slopes of 59.7, 58.1, 58.5, 58.5 and 57.0 for the PVC,SPE, CWE, CPE and MCPE for the proguanil ions in a wide concentration range of 1.0 * 10~(-5)–1.0 * 10~(-2)mol L~(-1) at 25°C with detection limits of 7.94 * 10~(-6), 1.0 * 10~(-5), 1.0 * 10~(-6), 7.07 * 10~(-6) and 2.5 * 10~(-6) mol L~(-1), respectively. The prepared electrodes exhibited high proguanil selectivity in relation to several inorganic ions and sugars and they could be successfully utilized for its determination in pure solutions, pharmaceutical preparations and serum and urine samples using the direct potentiometry and standard addition methods with very good recovery values.     

Determination of Sulfite in Real Sample by an Electrochemical Sensor Based on Ni/Poly(4-Aminobenzoic Acid)/Sodium Dodecylsulfate/Carbon Paste Electrode

In this research, a modified electrode has been produced during the electropolymerization of 4-Aminobenzoic acid in the presence of sodium dodecylsulfate (SDS) and then Ni(II) ions were incorporated to the polymer by immersion of the modified electrode in a 0.1 M Ni(II) ions solution. The electrochemical behavior of Ni/poly(4-aminobenzoic acid)/sodium dodecylsulfate/carbon paste electrode (Ni/poly(4-AB)/SDS/CPE) was investigated by using cyclic voltammetry. The experimental results exhibited the stable redox behavior of the Ni(III)/Ni(II) couple immobilized at the polymeric electrode. This polymeric modified electrode has a very good activity toward the sulfite electrooxidation in a phosphate buffer solution (pH 11). By comparison of the different responses to sulfite oxidation using electrodes Ni/poly(4-AB)/SDS/CPE, poly(4-AB)/SDS/CPE and CPE, we observed that the former electrode is a more effective catalyst for the electrooxidation of sulfite. Under optimal experimental conditions, the peak current response increased linearly with sulfite concentration over the range of 0.1–1 and 1–10 mM. The detection limit of the method was 0.063 mM. Finally, the method was applied to the determination of sulfite in weak liquor sample.     

The enhanced electrochemiluminescence of luminol on the nickel phthalocyanine modified electrode

A glassy carbon electrode (GCE) modified with nickel(II) tetrasulfophthalocyanine (NiTSPc) and Nafion was used for the investigation of the catalytic oxidation of luminol. The modified electrode was found to much more effectively improve the emission of electrochemiluminescence(ECL) of luminol in a solution containing hydrogen peroxide. The enhanced ECL signal corresponded to the catalytic oxidation of both luminol and H(2)O(2) by NiTSPc. Attached Ni(II) on GCE was oxidised to Ni(III) and then used as the catalyst for the chemiluminescence of luminol. The enhanced stability of the ECL signal with Nafion would mainly result from the prevention of the dissolution of NiTSPc and the adsorption of the oxidation product of luminol on the electrode surface. The proposed method enables a detection limit for luminal of 6.0 x 10(-8) mol L(-1) to be achieved in the presence of H(2)O(2) in the neutral solution. The enhanced ECL intensity had a linear relationship with the concentration of luminol in the range of 1.0 x 10(-7)-8.0 x 10(-6) mol L(-1).     

Methanol electrooxidation on novel modified carbon paste electrodes with supported poly(isonicotinic acid) (sodium dodecyl sulfate)/Ni-Co electrocatalysts

Poly(isonicotinic acid) (PINA) was formed by successive cyclic voltammetry in monomer solution in the presence of sodium dodecyl sulfate (SDS) on the surface of a carbon paste electrode (CPE). Ni(II) and Co(II) ions were incorporated into the electrode by immersion of the polymer-modified electrodes in Ni(II) and Co(II) ion solutions in different proportions. After the preparation of modified electrodes, their electrochemical behavior was studied by cyclic voltammetric experiments. Electrocatalytic oxidation of methanol at the surface of the modified electrodes was studied in 1?M NaOH solution. These modified electrodes exhibit high electrocatalytic activity and stability in alkaline solution, showing oxidation peaks at low potentials with high current densities. The electrooxidation of methanol was found to be more efficient on CPE/PINA(SDS)/Ni₈₀Co₂₀ than on CPE/PINA(SDS)/Ni and CPE/PINA(SDS)/Ni₅₀Co₅₀. The effects of various parameters such as scan rates and methanol concentration on the electrooxidation of methanol are also investigated.     

Synthesis, characterization, and electrochemiluminescence of luminol-reduced gold nanoparticles and their application in a hydrogen peroxide sensor

It was found that chloroauric acid (HAuCl(4)) could be directly reduced by the luminescent reagent luminol in aqueous solution to form gold nanoparticles (AuNPs), the size of which depended on the amount of luminol. The morphology and surface state of as-prepared AuNPs were characterized by transmission electron microscopy, UV/visible spectroscopy, X-ray photoelectron spectroscopy, FTIR spectroscopy, and thermogravimetric analysis. All results indicated that residual luminol and its oxidation product 3-aminophthalate coexisted on the surface of AuNPs through the weak covalent interaction between gold and nitrogen atoms in their amino groups. Subsequently, a luminol-capped AuNP-modified electrode was fabricated by the immobilization of AuNPs on a gold electrode by virtue of cysteine molecules and then immersion in a luminol solution. The modified electrode was characterized by cyclic voltammetry, electrochemical impedance spectroscopy, and scanning electron microscopy. The as-prepared modified electrode exhibited an electrochemiluminescence (ECL) response in alkaline aqueous solution under a double-step potential. H2O2 was found to enhance the ECL. On this basis, an ECL sensor for the detection of H2O2 was developed. The method is simple, fast, and reagent free. It is applicable to the determination of H2O2 in the range of 3x10(-7)-1x10(-3) mol L(-1) with a detection limit of 1x10(-7) mol L(-1) (S/N=3).     

铂单晶电极表面不可逆反应动力学II 铂单晶（100）晶面电极上甲酸氧化反应动力学参数解析

The kinetics of electrooxidation of HCOOH on Pt(100) via reactive intermediates was studied by using programmed potential step technique, which avoided successfully the interference of self-poisoning. A new data processing method was established based on the transform of integration of digital data recorded in electrochemical transient experiments, and the computer software developed for this method allowed us to obtain quantitatively, for the first time, the kinetics parameters of HCOOH oxidation on Pt(100) electrode. The results demonstrated that in a narrow potential range of 0.02 V to 0.15 V, the rate constant kf being varied from 9.510 × 10-4 to 1.38 ×10-2cm•s- 1 and the relationship between ln(kf) and E being a straight line. The transfer coefficient (β) was calculated at 0.309, and the diffusion coefficient (D) of HCOOH in 5×10-3mol•L- 1 HCOOH + 0. 5mol•L- 1 H2SO4 solution was evaluated at 1.80 × 10-5 cm2•s-1.