Dense passivating poly(ethylene glycol) films on indium tin oxide substrates

We describe the formation and characterization of surface-passivating poly(ethylene glycol) (PEG) films on indium tin oxide (ITO) glass substrates. PEG chains with a molecular weight of 2000 and 5000 D were covalently attached to the substrates in a systematic approach using different coupling schemes. The coupling strategies included the direct grafting with PEG-silane, PEG-methacrylate, and PEG-bis(amine), as well as the two-step functionalization with aldehyde-bearing silane films and subsequent coupling with PEG-bis(amine). Elemental analysis by X-ray photoelectron spectroscopy (XPS) confirmed the successful surface modification, and XPS and ellipsometry provided values for film thicknesses. XPS and ellipsometry thickness values were almost identical for PEG-silane films but differed by up to 400% for the other PEG layers, suggesting a homogeneous layer for PEG-silane but an inhomogeneous distribution for other PEG coatings on the molecularly rough ITO substrates. Atomic force microscopy (AFM) and water contact angle goniometry confirmed the different degrees of surface homogeneity of the polymer films, with PEG-silane reducing the AFM rms surface roughness by 50% and the water contact angle hysteresis by 75% compared to uncoated ITO. The ability of the PEG layers to passivate the substrate against the nonspecific adsorption of biopolymers was tested using fluorescence-labeled immunoglobulin G and DNA oligonucleotides in combination with fluorescence microscopy. The results indicate a positive relationship between film density and homogeneity on one hand and the ability to passivate against biopolymer adhesion on the other hand. The most homogeneous layers prepared with PEG-silane reduced the nonspecific adsorption of fluorescence-labeled DNA by a factor of 300 compared to uncoated ITO. In addition, the study finds that the ratio of film thicknesses derived by ellipsometry and XPS is a useful parameter to quantify the structural integrity of PEG layers on molecularly rough ITO surfaces. The findings may be applied to characterize PEG or other polymeric films on similarly coarse substrates.     

Ultrathin coatings from isocyanate terminated star PEG prepolymers: patterning of proteins on the layers

This study presents the easy and fast patterning of low molecular weight molecules that act as binding partners for proteins on Star PEG coatings. These coatings are prepared from isocyanate terminated star shaped prepolymers and form a highly cross-linked network on the substrate in which the stars are connected via urea groups and free amino groups are present. Streptavidin has been patterned on these layers by microcontact printing (muCP) of an amino reactive biotin derivative and consecutive binding of streptavidin to the biotin. Patterns of Ni(2+)-nitriltriacetic acid (NTA) receptors have been prepared by printing amino functional NTA molecules in freshly prepared Star PEG layers that still contain amino reactive isocyanate groups. Complexation of the NTA groups with Ni(II) ions enabled the binding of His-tag enhanced green fluorescent protein (EGFP) in the desired pattern on the substrates. Since the unmodified Star PEG layers prevent unspecific protein adsorption, His-EGFP could selectively be bound to the sample by immersion into crude, nonpurified His-tag EGFP containing cell lysate.     

Relationship between interfacial forces measured by colloid-probe atomic force microscopy and protein resistance of poly(ethylene glycol)-grafted poly(L-lysine) adlayers on niobia surfaces

Adsorbed layers of "comb-type" copolymers consisting of PEG chains grafted onto a poly(l-lysine) (PLL) backbone on niobium oxide substrates were studied by colloid-probe AFM in order to characterize the interfacial forces associated with coatings of varying architectures (PEG/PLL ratios and PEG chain lengths) and their relevance to protein resistance. The steric and electrostatic forces measured varied substantially with the architecture of the PLL-g-PEG copolymers. Varying the ionic strength of the buffer solutions enabled discrimination between electrostatic and steric-entropic contributions to the net interfacial force. For high PEG grafting densities the steric component was most prominent, but at low ionic strengths and high grafting densities, a repulsive electrostatic surface force was also observed; its origin was assigned to the niobia charges beneath the copolymer, as insufficient protonated amine groups in the PLL backbone were available for compensation of the oxide surface charges. For lower grafting densities and lower ionic strengths there was a substantial attractive electrostatic contribution arising from interaction of the electrical double layer arising from the protonated amine groups, with that of the silica probe surface (as under low ionic strength conditions, the electrical double layer was thicker than the PEG layer). For these PLL-g-PEG coatings the net interfacial force can thus be a markedly varying superposition of electrostatic and steric-entropic contributions, depending on various factors. The force curves correlate with protein adsorption data, demonstrating the utility of AFM colloid-probe force measurements for quantitative analysis of surface forces and how they determine interfacial interactions with proteins. Such characterization of the net interfacial forces is essential to elucidate the multiple types of interfacial forces relevant to the interactions between PLL-g-PEG coatings and proteins and to advance interpretation of protein adsorption or repellence beyond the oversimplified steric barrier model; in particular, our data demonstrate the importance of an ionic-strength-dependent minimum PEG layer thickness to screen the electrostatic interactions of charged interfaces.     

Thickness and morphology of polyelectrolyte coatings on silica surfaces before and after protein exposure studied by atomic force microscopy

Analyte–wall interaction is a significant problem in capillary electrophoresis (CE) as it may compromise separation efficiencies and migration time repeatability. In CE, self-assembled polyelectrolyte multilayer films of Polybrene (PB) and dextran sulfate (DS) or poly(vinylsulfonic acid) (PVS) have been used to coat the capillary inner wall and thereby prevent analyte adsorption. In this study, atomic force microscopy (AFM) was employed to investigate the layer thickness and surface morphology of monolayer (PB), bilayer, (PB-DS and PB-PVS), and trilayer (PB-DS-PB and PB-PVS-PB) coatings on glass surfaces. AFM nanoshaving experiments providing height distributions demonstrated that the coating procedures led to average layer thicknesses between 1 nm (PB) and 5 nm (PB-DS-PB), suggesting the individual polyelectrolytes adhere flat on the silica surface. Investigation of the surface morphology of the different coatings by AFM revealed that the PB coating does not completely cover the silica surface, whereas full coverage was observed for the trilayer coatings. The DS-containing coatings appeared on average 1 nm thicker than the corresponding PVS-containing coatings, which could be attributed to the molecular structure of the anionic polymers applied. Upon exposure to the basic protein cytochrome c, AFM measurements showed an increase of the layer thickness for bare (3.1 nm) and PB-DS-coated (4.6 nm) silica, indicating substantial protein adsorption. In contrast, a very small or no increase of the layer thickness was observed for the PB and PB-DS-PB coatings, demonstrating their effectiveness against protein adsorption. The AFM results are consistent with earlier obtained CE data obtained for proteins using the same polyelectrolyte coatings.     

Effects of ionic strength and surface charge on protein adsorption at PEGylated surfaces

PEGylated Nb2O5 surfaces were obtained by the adsorption of poly(L-lysine)-g-poly(ethylene glycol) (PLL-g-PEG) copolymers, allowing control of the PEG surface density, as well as the surface charge. PEG (MW 2 kDa) surface densities between 0 and 0.5 nm(-2) were obtained by changing the PEG to lysine-mer ratio in the PLL-g-PEG polymer, resulting in net positive, negative and neutral surfaces. Colloid probe atomic force microscopy (AFM) was used to characterize the interfacial forces associated with the different surfaces. The AFM force analysis revealed interplay between electrical double layer and steric interactions, thus providing information on the surface charge and on the PEG layer thickness as a function of copolymer architecture. Adsorption of the model proteins lysozyme, alpha-lactalbumin, and myoglobin onto the various PEGylated surfaces was performed to investigate the effect of protein charge. In addition, adsorption experiments were performed over a range of ionic strengths, to study the role of electrostatic forces between surface charges and proteins acting through the PEG layer. The adsorbed mass of protein, measured by optical waveguide lightmode spectroscopy (OWLS), was shown to depend on a combination of surface charge, protein charge, PEG thickness, and grafting density. At high grafting density and high ionic strength, the steric barrier properties of PEG determine the net interfacial force. At low ionic strength, however, the electrical double layer thickness exceeds the thickness of the PEG layer, and surface charges "shining through" the PEG layer contribute to protein interactions with PLL-g-PEG coated surfaces. The combination of AFM surface force measurements and protein adsorption experiments provides insights into the interfacial forces associated with various PEGylated surfaces and the mechanisms of protein resistance.     

Biofunctionalized, ultrathin coatings of cross-linked star-shaped poly(ethylene oxide) allow reversible folding of immobilized proteins

Dense, ultrathin networks of isocyanate terminated star-shaped poly(ethylene oxide) (PEO) molecules, cross-linked at their chain ends via urea groups, were shown to be extremely resistant to unspecific adsorption of proteins while at the same time suitable for easy biocompatible modification. Application by spin coating offers a simple procedure for the preparation of minimally interacting surfaces that are functionalized by suitable linker groups to immobilize proteins in their native conformations. These coatings form a versatile basis for biofunctional and biomimetic surfaces. We have demonstrated their advantageous properties by using single-molecule fluorescence microscopy to study immobilized proteins under destabilizing conditions. Biotinylated ribonuclease H (RNase H) was labeled with a fluorescence resonance energy transfer (FRET) pair of fluorescent dyes and attached to the surface by a biotin-streptavidin linkage. FRET analysis demonstrated completely reversible denaturation/renaturation behavior upon exposure of the surface-immobilized proteins to 6 M guanidinium chloride (GdmCl) followed by washing in buffer. A comparison with bovine serum albumin (BSA) coated surfaces and linear PEO brush surfaces yielded superior performance in terms of chemical stability, inertness and noninteracting nature of the star-polymer derived films.     

Surface grafting of PEO-based star-shaped molecules for bioanalytical and biomedical applications

This article reviews surface grafting of star-shaped PEO. The use of star-shaped polymers is compared to linear PEO chains regarding the layer preparation and the ability of the resulting surfaces to resist protein adsorption. We then focus on the use of end-functionalized, star-shaped, PEO-based prepolymers that are able to form covalent crosslinks and functional polymer networks on the substrate. Examples are given for specific protein adsorption as well as for cell adhesion on such layers by covalent embedding of biofunctional molecules. The possibility of coating biomedically relevant polymer substrates in three-dimensional geometries is discussed and examples are shown for poly(ethylene terephthalate) monofilament constructs.     

Novel type of self-assembled polyamide and polyimide nanoengineered shells--fabrication of microcontainers with shielding properties

Two types of microcontainers were prepared by using the adsorption of polyamide on the surface of micrometer-sized inorganic porous calcium carbonate microparticles followed by thermal conversion of the polyamide layers into polyimide coatings. The effect of the preparation conditions on the structure and morphology of the microcontainers was studied by transmission electron microscopy and scanning electron microscopy. The smoothest and defect-free coatings were prepared using polyethylenimine as the supporting polymer. The thickness of the polyamide/polyimide shells was estimated by atomic force microscopy and scanning electron microscopy between 50 and 150 nm depending on the quantity of the layers. The water-soluble antibiotic, doxorubicin hydrochloride, was used as a model compound to demonstrate the efficiency of the microcontainers for encapsulation. The resistance of the novel microcontainers to solvent treatment was visualized by the confocal scanning fluorescence microscopy. It was demonstrated that the combination of the high thermal and chemical resistance of polyamide/polyimide shell and the sorption capacity of the CaCO3 is very useful for development of highly protective microcontainers and thermal detectors for smart fabrics.     

Fabrication and anti-fouling properties of photochemically and thermally immobilized poly(ethylene oxide) and low molecular weight poly(ethylene glycol) thin films

Poly(ethylene oxide) (PEO) and low molecular weight poly(ethylene glycol) (PEG) were covalently immobilized on silicon wafers and gold films by way of the CH insertion reaction of perfluorophenyl azides (PFPAs) by either photolysis or thermolysis. The immobilization does not require chemical derivatization of PEO or PEG, and polymers of different molecular weights were successfully attached to the substrate to give uniform films. Microarrays were also generated by printing polymer solutions on PFPA-functionalized wafer or Au slides followed by light activation. For low molecular weight PEG, the immobilization was highly dependent on the quality of the film deposited on the substrate. While the spin-coated and printed PEG showed poor immobilization efficiency, thermal treatment of the PEG melt on PFPA-functionalized surfaces resulted in excellent film quality, giving, for example, a grafting density of 9.2×10(-4)?(-2) and an average distance between grafted chains of 33? for PEG 20,000. The anti-fouling property of the films was evaluated by fluorescence microscopy and surface plasmon resonance imaging (SPRi). Low protein adsorption was observed on thermally-immobilized PEG whereas the photoimmobilized PEG showed increased protein adsorption. In addition, protein arrays were created using polystyrene (PS) and PEG based on the differential protein adsorption of the two polymers.     

Nanostructure of polymer layers formed upon the adsorption from binary and ternary solutions

Thicknesses of nanolayers formed upon the adsorption from dilute and semidilute solutions of polystyrene, poly(butyl methacrylate), and their mixtures on the surface of solid SiO₂ are estimated on the basis of adsorption isotherms and atomic force microscopy measurements. It is established that the thickness of an adsorption layer is determined by the sizes of individual macromolecular coils and clusters arising in a solution. In the case of polymer blends, adsorption leads to the formation of mosaic structures with the alternation of polymeric components in the substrate plane; the characteristic size of a domain is ≈200 nm for each component. It is shown that adsorption layers formed on the surface of a silicon single crystal (covered with intact oxide) are fractal objects whose dimension depends on the nature of polymer and conditions of its adsorption.     

Formation of antifouling functional coating from deposition of a zwitterionic-co-nonionic polymer via “grafting to” approach

We develop a new process for the preparation of synergistic antifouling functional coatings on gold surfaces via a “grafting to” approach. The strategy includes a synthetic step of polymer brushes that consist of poly (ethylene glycol) (PEG) and zwitterionic side chains via a typical reversible-addition fragmentation chain transfer (RAFT) polymerization process, and a subsequent deposition of the polymer brushes onto a gold substrate. The presence of PEG and zwitterion chains on these polymer brush-coated gold surfaces has been proved to have a synergistic effect on the final antifouling property of the coating. PEG chains lower the electrostatic repulsion between zwitterionic polymer chains and increase their graft density on gold surfaces, while zwitterionic polymer effectively improves the antifouling property that is offered by PEG chains alone. Protein adsorption and cell attachment assays tests are conducted to confirm that this copolymer layer on gold surface has a pronounced resistance against proteins such as Bovine serum albumin and Lysozyme. Importantly, the antifouling property can be systematically adjusted by varying the molar ratio of PEG to zwitterionic chains in the final coating copolymer.     

Elaboration and characterisation of yttria psz coatings deposited by RF sputtering on silicon

Yttria stabilised Zirconia coatings on polycrystalline silicon wafers have been performed using physical vapor deposition with negative bias applied to the substrate. The thicknesses determined by ellipsometry were between 45 and 70 nm and the deposition rate was about 0.25 nm per min. Secondary ion mass spectroscopy analyses revealed no interdiffusion of metallic elements between the zirconia coating and silicon substrate. Grazing incidence X-ray diffraction indicates that the coatings are crystallized, but it can not permit to identify all the crystalline phases. The disparity between the experimental and the k-ratios (Pouchou and Pichoir simulation of electron probe microanalysis analyses) showed the usefulness of others techniques to determine coating and interface compositions. Cross sectional transmission electron microscopy observations demonstrate an amorphous layer between the zirconia coating and the substrate with a thickness of 30–120 nm. If it is considered to be an amorphous silicon layer, the PAP simulation based on the ellipsometric thicknesses and an yttria stabilised zirconia density of 4 g/cm³ fits correctly the experimental values.     

Development of dextran-derivative arrays to identify physicochemical properties involved in biofouling from serum

To control protein adsorption on surfaces, low-fouling polymer coatings such as poly(ethylene oxide) (PEG or PEO) and polysaccharides are used. Their ability to resist protein adsorption is related to the layer structure, hence the immobilization mode. A polymer array technology was developed to study the structural diversity of carboxymethyl dextran (CMD) layers, whose immobilization conditions were varied. CMD arrays were analyzed by X-ray photoelectron spectroscopy (XPS) and by atomic force microscopy (AFM) colloidal probe force measurements. Serum protein adsorption was studied directly on the CMD arrays using surface plasmon resonance (SPR) microscopy. Physicochemical characterization revealed that pinning density regulates surface coverage and the amount of adsorbed molecules, and that salt concentration influences the surface structure of the charged polymer, forming extended or short layers. Protein adsorption experiments from serum showed that repulsive CMD layers are dense, with extended flexible chains. The present study underlines the usefulness of polymer arrays to study structural diversity of thin graft layers and to relate their physicochemical properties to their resistance to nonspecific protein adsorption.     

Formation of Anatase Nanocrystals-Precipitated Silica Coatings on Plastic Substrates by the Sol-Gel Process with Hot Water Treatment

Anatase nanocrystals-precipitated silica coatings were formed on plastic substrates such as poly(ethylene terephtalate) (PET), acrylic resin (AC) and polycarbonate (PC) from silica-titania gel coatings with and without addition of poly(ethylene glycol) (PEG) by hot water treatment. The maximum thickness of the coatings which can be formed without cracking or peeling-off was 100 to 200 nm for PET and PC substrates, whereas it was less than 50 nm for AC substrates. After a hot water treatment at 90°C for 120 min, the size of the anatase nanocrystals increased to be 30 and 50 nm for the coatings obtained with and without PEG, respectively. Anatase nanocrystals were formed throughout the whole of the coatings obtained with PEG and were formed only on the surface of the coatings obtained without PEG. Both coatings obtained with and without PEG were highly transparent. The plastic substrates with coatings obtained without PEG showed good weathering resistance owing to the protective effects of the residual silica under-layer. The coatings obtained with PEG showed higher photocatalytic activities than those obtained without PEG due to smaller size and higher dispersion of anatase nanocrystals in the coatings.     

Iron oxide film growth under ultrathin polysiloxane networks

This study focuses on the preparation and characterization of magnetic switchable thin iron oxide–polymer films. In a series of experiments, the formation and growth of iron oxide under ultrathin polysiloxane layers was controlled by changing the concentration of iron ions in the aqueous subphase or by varying the residence time of ammonia in the gas phase above the liquid sample. The growth of the combined film structures is studied in situ by interfacial rheology, optical microscopy, and x-ray scattering experiments and ex situ by scanning electron microscopy. Different stages of iron oxide aggregation, from a very thin layer of amorphous iron oxide with thickness of a few nanometers up to micrometer thick coatings of crystalline maghemite (γ-Fe₂O₃) were investigated. The specific interactions between the inorganic iron oxide and the polymer membranes cause the creation of new composite materials which are sensitive to magnetic forces.

Thin films of cross-linked metallo-supramolecular coordination polyelectrolytes

We report on the synthesis of a new tristerpyridine ligand, tris(2,2':6',2' '-terpyridinyl-4'-oxymethyl)ethane (tritpy), as well as its introduction into metal ion induced self-assembly of cross-linked metallo-supramolecular coordination polyelectrolytes (MEPE). For cross-linking degrees of 9.5% and below, soluble homogeneous networks are obtained. The molar mass of the networks is large and depends on the cross-linking degree. Due to the charges in the MEPE, the soluble networks are suitable for film formation on the basis of layer-by-layer self-assembly and to study the details of film growth. UV-vis spectroscopy, X-ray reflectivity, AFM, and ellipsometry show that the film growth is linear and continuous. The multilayers exhibit no inner structure and have a very low surface roughness. The thickness of the adsorbed layer of MEPE networks is in the range of 3 nm. The important point is that an influence of cross-linking is not seen in multilayers, which is the opposite of what is observed for the MEPE in solution. Our experiments did not reveal an influence of the preparation procedure on the adsorption process, e.g., increasing the layer thickness.     

TIRF microscopy as a screening method for non-specific binding on surfaces

We report a method for studying nanoparticle-biosensor surface interactions based on total internal reflection fluorescence (TIRF) microscopy. We demonstrate that this simple technique allows for high throughput screening of non-specific adsorption (NSA) of nanoparticles on surfaces of different chemical composition. Binding events between fluorescent nanoparticles and functionalized Zeonor? surfaces are observed in real-time, giving a measure of the attractive or repulsive properties of the surface and the kinetics of the interaction. Three types of coatings have been studied: one containing a polymerized aminosilane network with terminal -NH(2) groups, a second film with a high density of -COOH surface groups and the third with sterically restraining branched poly(ethylene)glycol (PEG) functionality. TIRF microscopy revealed that the NSA of nanoparticles with negative surface charge on such modified coatings decreased in the following order -NH(2)>-branched PEG>-COOH. The surface specificity of the technique also allows discrimination of the degree of NSA of the same surface at different pH.     

Membrane Preparation of Polysulfonic Acid Complexes by Layer-by-Layer Adsorption

Summary: The water-insoluble, thermostable and homogeneous polymer complex membrane formation of polysulfonic acids was examined by modifying the preparation conditions of the layer-by-layer adsorption method of the acid and base polymers. The complexation of poly(4-styrenesulfonic acid) in the 0.15 unit mM solution with poly(allylamine) gave a polymer complex membrane on a gold substrate in which one polymer layer was formed with a thickness of 1 nm. Properties including the proton conductivity of the membrane suggested possible applications of the polymer complex membrane.     

Initial Growth of Functional Plasma Polymer Nanofilms

To gain deeper insights into the initial growth mechanism, with respect to functional group density and cross-linking, plasma polymer films (PPFs) were deposited from C₂H₄/NH₃ discharges. Keeping gas phase processes and electrical discharge conditions constant all over the deposition process, the mass deposition rate of the PPF was found to be initially lower and regularly increasing before reaching steady-state conditions after a film thickness of about 5 nm on metal oxide substrates. The first gradient nano-layer, i.e. the first 5 nm deposited, were observed to possess less amino functional groups and to be more cross-linked and thus more stable compared to the film prepared in steady state conditions, in which the uniform film comprises more amino functional groups, yet is less cross-linked and thus less stable. Due to its sticking probability, the substrate thus influences the initial deposition rate. Over plasma exposure time, the substrate becomes covered by an initial layer of PPF and the film-forming species are no longer deposited onto the pristine substrate but onto the already deposited organic polymer film. The preparation of the highly stable functional nanofilm, i.e. the initial PPF layer, can lead to new possible applications and fast deposition processes.     

Density control of poly(ethylene glycol) layer to regulate cellular attachment

A wide variety of cells usually integrate and respond to the microscale environment, such as soluble protein factors, extracellular matrix proteins, and contacts with neighboring cells. To gain insight into cellular microenvironment design, we investigated two-dimensional microarray formation of endothelial cells on a micropatterned poly(ethylene glycol) (PEG)-brushed surface, based on the relationship between PEG chain density and cellular attachment. The patterned substrates consisted of two regions: the PEG surface that acts as a cell-resistant layer and the exposed substrate surface that promotes protein or cell adsorption. A PEG-brushed layer was constructed on a gold substrate using PEG with a mercapto group at the end of the chain. The density of the PEG-brushed layer increased substantially with repetitive adsorption/rinse cycles of PEG on the gold substrate, allowing marked reduction of nonspecific protein adsorption. These repeated adsorption/rinse cycles were further regulated by using longer (5 kDa) and shorter (2 kDa) PEG to construct PEG layers with different chain density, and subsequent micropatterning was achieved by plasma etching through a micropatterned metal mask. The effects of PEG chain density on pattern formation of cell attachment were determined on micropatterning of endothelial cells. The results indicated that cell pattern formation was strongly dependent on the PEG chain density and on the extent of protein adsorption. Notably, a PEG chain density high enough to inhibit outgrowth of endothelial cells from the cell-adhering region in the horizontal direction could be obtained only by employing formation of a short filler layer of PEG in the preconstructed longer PEG-brushed layer, which prevented nonspecific protein adsorption almost completely. In this way, a completely micropatterned array of endothelial cells with long-term viability was obtained. This clearly indicated the importance of a short underbrushed PEG layer in minimizing nonspecific protein adsorption for long-term maintenance of the active cell pattern. The strategy for cell patterning presented here can be employed in tissue engineering to study cell-cell and cell-surface interactions. It is also applicable for high-throughput screening and clinical diagnostics, as well as interfacing cellular and microfabricated components of biomedical microsystems.