Novel approach to improve the detection of colchicine via online coupling of ionic liquid-based single-drop microextraction with capillary electrophoresis

A novel approach based on ionic liquid‐single‐drop microextraction (IL‐SDME) online coupling with capillary electrophoresis (CE) was used to determine a toxic alkaloid – colchicine. The IL‐SDME procedure was optimized by extraction solvent, drop volume controlling, sample volume and pH, extraction time, and ionic strength. Under optimum conditions, enrichment factor was as much as 41‐fold with a relative standard deviation of 2.8% (n=3). Linear range of response was observed from 1 to 100 μg/mL, with detection limit of 0.25 μg/mL and correlation coefficient (R²) of 0.9994. The extraction of colchicine from spiked Lanzhou lily sample was performed and obtaining good result with an average recovery rate of 102.4 and 98.8% at 5 and 50 μg/mL, respectively. Comparing with the previous methods, IL‐SDME‐CE is really a convenient, economical, and environmentally benign way for determining colchicine.     

Sensitive determination of free benzophenone-3 in human urine samples based on an ionic liquid as extractant phase in single-drop microextraction prior to liquid chromatography analysis

Benzophenone-3 (BZ3), one of the compounds most commonly used as UV filter in cosmetic products, can be absorbed through the skin into the human body, since it can be found at trace levels in urine from users of cosmetic products that contain BZ3. Moreover, different undesirable effects have been attributed to this compound. Thus, sensitive analytical methods to monitor urinary excretion of this compound should be developed. This paper presents a selective and sensitive methodology for BZ3 determination at ultratrace levels in human urine samples. The methodology is based on a novel microextraction technique, known as single-drop microextraction (SDME). An ionic liquid (IL) has been used as extractant phase instead of an organic solvent. After the microextraction process, the extractant phase was injected into a liquid chromatography system. The variables of interest in the SDME process were optimized using a multivariate optimization approach. A Plackett-Burman design for screening and a circumscribed central composite design for optimizing the significant variables were applied. Ionic strength, extraction time, stirring speed, pH, ionic liquid type, drop volume and sample volume were the variables studied. The optimum experimental conditions found were: sodium chloride concentration, 13% (w/v); extraction time, 25 min; stirring speed, 900 rpm; pH, 2; ionic liquid type, 1-hexyl-3-methylimidazolium hexafluorophosphate ([C(6)MIM][PF(6)]); drop volume, 5 microL; and sample volume, 10 mL. The proposed method requires a standard addition calibration approach, and it has been successfully employed to determine free BZ3 in urine samples coming from human volunteers who applied a sunscreen cosmetic containing this UV filter. The limit of detection was in the order of 1.3 ng mL(-1) and repeatability of the method, expressed as relative standard deviation, was 6% (n=8).     

Simple and commercial readily-available approach for the direct use of ionic liquid-based single-drop microextraction prior to gas chromatography: Determination of chlorobenzenes in real water samples as model analytical application

A simple and commercial readily-available approach that enables the direct use of ionic liquid (IL)-based single-drop microextraction (SDME) prior to gas chromatography (GC) is presented. The approach is based on thermal desorption (TD) of the analytes from the IL droplet to the GC system, by using a robust and commercially-available thermodesorption system. For this purpose, a two-glass-tube concentrically disposed system was designed. The inner tube is a laboratory-cut Pyrex tube (20 mm length) that houses the ionic liquid droplet from the SDME process, and the outer tube is a commercially-available TD glass tube (187 mm length) commonly employed for stir-bar sorptive extractions (SBSE). In this way, the proposed device prevents IL from entering the GC system, as this could dirty the inlet or even block the column. The determination of 10 chlorobenzenes in water samples by GC coupled with mass spectrometric (MS) detection has been chosen as model analytical application, showing the feasibility of the proposed approach. The SDME process consists of a 5 μL droplet of 1-hexyl-3-methylimidazolium hexafluorophosphate ([C₆MIM][PF₆]) suspended in the headspace (HS) of a 10 mL stirred sample. After extracting for 37 min at room temperature, the IL droplet is directly placed into the small inner tube, which is placed into the TD tube. The whole device is placed inside the TD unit, where desorption of the analytes is performed at 240 °C for 5 min with a helium flow rate of 100 mL min⁻¹. The analytical figures of merit of the proposed IL-(HS)-SDME-TD-GC–MS approach are very suitable for the determination of chlorobenzenes at ultratrace levels, with relative standard deviation values ranging between 2% and 17%, and limits of detection ranging between 1 and 4 ng L⁻¹, showing the potential offered by the IL-based SDME process with GC.     

Revolving hollow fiber–liquid phase microextraction coupled to GC/MS using electron ionization for quantification of five aromatic hydrocarbon isomers

A dynamic liquid phase microextraction method using a revolving hollow fiber was demonstrated for coupling to GC/MS [using EI (electronic ionization) and selected ion monitor (SIM)] as a concentrating probe for rapid analysis and quantitative determination of five aromatic hydrocarbon isomers (cumene; propylbenzene; 2‐ethyltoluene; 1,2,3‐trimethylbenzene; and 1,2,4‐trimethylbenzene) from biological matrices (human urine and human plasma). This technique was named as revolving hollow fiber–liquid phase microextraction (RHF–LPME). The optimized parameters of RHF–LPME coupled to GC/MS experiments were extraction solvent, toluene; extraction time, 2 min; sample agitation rate, 700 rpm; salt concentration, 0%; rotating speed for motor driving rotator, 250 rpm; and the rotator was operated in a reversed direction with the stirrer. The linear range of calibration curve of RHF–LPME was from 0.002 to 0.4 μg/mL with R² > 0.9916 and the RSD values were from 4.5 to 5.2%. Additionally, comparing to single drop microextraction (SDME), this method offers better limits of detection (LODs) and EF (enrichment factor). This approach exhibits many advantages including simplicity, rapid detection with high reproducibility and high extraction efficiency, easy to operate and fast to reach equilibrium for analyzing biological samples. This approach has the potential to be widely used because it only requires simple devices to perform all extraction processes. We believe that this technique can be a powerful tool for GC/MS analysis of biological samples and clinical applications in the near future.     

A rapid, sensitive and effective quantitative method for simultaneous determination of cationic surfactant mixtures from river and municipal wastewater by direct combination of single-drop microextraction with AP-MALDI mass spectrometry

A rapid, simple, sensitive, and effective quantitative method for simultaneous determination of cationic surfactants (CS(+)) from river and municipal wastewater by direct combination of single-drop microextraction (SDME) with atmospheric pressure (AP)-MALDI mass spectrometry has been successfully demonstrated without the requirements of tedious sample pre- or post-treatment or separation by high-performance liquid chromatography (HPLC), gas chromatography (GC), and capillary electrophoresis (CE). This quantitative method can greatly enhance the signal-to-noise ratio for analysis of small molecules of CS(+) owing to the strong suppression of matrix ions by the analytes. In addition, SDME assisted in the isolation and preconcentration of CS(+) from water samples, which could effectively reduce the background interferences from the matrices present in waste and river water. The SDME conditions were optimized for achieving high extraction efficiency of CS(+) from aqueous samples, in terms of solvent selection, stirring speed, extraction time, exposure volume of acceptor phase, and salt addition. The enrichment factors for CS(+) were found to be 40-64-folds for 7 min of extraction time with no salt addition and at room temperature. This method was found to yield a linear calibration curve in the concentration range from 50 to 1500 microg/l CS(+) with a limit of detection (LOD) of 10 microg/l. The relative recoveries in river and municipal wastewater were found to be 93.8-103.6% and 91.0-98.7%, respectively. These results indicate that the combination of SDME with AP-MALDI/MS is effective for the simultaneous determination of CS(+) from river and municipal wastewater. In addition, a comparison of enrichments and LOD values for this method with hollow-fiber liquid phase microextraction (HF-LPME) was also demonstrated. The present approach is easy to operate, rapid, sensitive, and suitable for high-throughput of analysis.     

Headspace Single Drop Microextraction Using Micellar Ionic Liquid Extraction Solvents

A headspace single drop microextraction (SDME) method using extraction solvents comprised of micellar ionic liquids (ILs) was used to perform the extraction of 17 aromatic compounds from aqueous solution and coupled with liquid chromatography. The effects of various experimental parameters including type of micellar IL extraction solvent, stir rate, extraction time, volume of the microdroplet, and addition of organic solvent were investigated and optimized. Two different micellar solutions were formed by dissolving 1-decyl-3-methylimidazolium bromide ([DMIM][Br]) and sodium dodecyl sulfate (SDS) in 1-butyl-3-methylimidazolium chloride ([BMIM][Cl]). It was observed that the enrichment factors of the 17 studied compounds were all enhanced with the micellar ionic liquid extraction solvent compared to the neat [BMIM][Cl] IL. The highest sensitivity was obtained with the [BMIM][Cl]–[DMIM][Br] micellar solution for polycyclic aromatic hydrocarbons (PAHs) with high molecular weight and fused rings while the [BMIM][Cl]–SDS micellar solution was proven to be more sensitive for smaller, more polar molecules. The detection limits were lower when utilizing the [BMIM][Cl]–SDS and [BMIM][Cl]–[DMIM][Br] extraction solvents compared to the neat [BMIM][Cl] extraction solvent. The reproducibility of the extraction method at 20 °C using extraction solvents composed of [BMIM][Cl]–SDS and [BMIM][Cl]–[DMIM][Br] ranged from 6.7 to 14.0 and 4.2 to 14.7%, respectively.     

Solubilization of thermotropic liquid crystal compounds in aqueous surfactant solutions

We study the micellar solubilization of three thermotropic liquid crystal compounds by immersing single drops in aqueous solutions of the ionic surfactant tetradecyltrimethylammonium bromide. For both nematic and isotropic drops, we observe a linear decrease of the drop size with time as well as convective flows and self-propelled motions. The solubilization is accompanied by the appearance of small aqueous droplets within the nematic or isotropic drop. At low temperatures, nematic drops expell small nematic droplets into the aqueous environment. Smectic drops show the spontaneous formation of filament-like structures which resemble the myelin figures observed in lyotropic lamellar systems. In all cases, the liquid crystal drops become completely solubilized, provided the weight fraction of the liquid crystal in the system is not larger than a few percent. The solubilization of the liquid crystal drops is compared with earlier studies of the solubilization of alkanes in ionic surfactant solutions.     

Determination of organochlorine pesticides in complex matrices by single-drop microextraction coupled to gas chromatography-mass spectrometry

A rapid and simple single-drop microextraction method (SDME) has been used to preconcentrate eighteen organochlorine pesticides (OCPs) from water samples with a complex matrix. Exposing two microlitre toluene drop to an aqueous sample contaminated with OCPs proved an excellent preconcentration method prior to analysis by gas chromatography-mass spectrometry (GC-MS). A Plackett-Burman design was used for screening and a central composite design for optimizing the significant variables in order to evaluate several possibly influential and/or interacting factors. The studied variables were drop volume, aqueous sample volume, agitation speed, ionic strength and extraction time. The optimum experimental conditions of the proposed SDME method were: 2 μL toluene microdrop exposed for 37 min to 10 mL of the aqueous sample containing 0% w/v NaCl and stirred at 380 rpm.The calculated calibration curves gave high-level linearity for all target analytes with correlation coefficients ranging between 0.9991 and 0.9999. The repeatability of the proposed method, expressed as relative standard deviation, varied between 5.9 and 9.9% (n = 8). The detection limits were in the range of 0.022-0.101 μg L⁻¹ using GC-MS with selective ion monitoring. The LOD values obtained are able to detect these OCPs in aqueous matrices as required by EPA Method 625. Analysis of spiked effluent wastewater samples revealed that the matrix had no effect on extraction for eleven of the analytes but exerted notable effect for the other analytes.     

On-line coupling of ionic liquid-based single-drop microextraction with capillary electrophoresis for sensitive detection of phenols

An ionic liquid-based single-drop microextraction (IL-SDME) procedure using IL as an extractant on-line coupled to capillary electrophoresis (CE) is proposed. The method is capable of quantifying trace amounts of phenols in environmental water samples. For the SDME of three phenols, a 2.40 nL IL microdrop was exposed for 10 min to the aqueous sample and then was directly injected into the capillary column for analysis. Extraction parameters such as the extraction time, the IL single-drop volume, pH of the sample solution, ionic strength, volume of the sample solution and the extraction temperature were systematically investigated. Detection limits to three phenols were less than 0.05 μg mL⁻¹, and their calibration curves were all linear (R² ≥ 0.9994) in the range from 0.05 to 50 μg mL⁻¹. And enrichment factors for three phenols were 156, 107 and 257 without agitation, respectively. This method was then utilized to analyze two real environmental samples from Yellow River and tap water, obtaining satisfactory results. Compared with the usual SDME for CE, IL-SDME–CE is a simple, low-cost, fast and environmentally friendly preconcentration technique.     

Coupling of ionic liquid-based headspace single-drop microextraction with GC for sensitive detection of phenols

A headspace single-drop microextraction (SDME) based on ionic liquid (IL) has been developed for the gas chromatographic determination of phenols. The volume of IL microdrop used was 1 microL. After extraction, the analytes were desorbed from the drop in the injection port and the involatile IL was withdrawn into the microsyringe. To facilitate the withdrawal of IL the upper diameter of the split inlet liner was enlarged to some extent. Some parameters were optimized for the determination of phenols. Under the selected conditions, i.e., desorption for 100 s at 210 degrees C after extraction for 25 min at 50 degrees C in solutions (pH 3) containing 0.36 g/mL sodium chloride, the LODs, RSDs, and the average enrichment factors of phenols were 0.1-0.4 ng/mL, 3.6-9.5% (n=5), and 35-794, respectively. The proposed procedure was applied to the determination of phenols in lake water and wastewater samples, and the spiked recoveries were in the range of 81-111% at a spiked level of 0.4 microg/mL. This method is a promising alternative for the sensitive determination of phenolic compounds.     

Development of an ionic liquid-based dispersive liquid-liquid micro-extraction method for the determination of phthalate esters in water samples

Ionic liquid-based dispersive liquid-liquid micro-extraction (IL-DLLME) was coupled with high-performance liquid chromatography-ultraviolet (HPLC-UV) for the determination of four phthalate esters, including butyl benzyl phthalate, di-n-butyl phthalate, dicyclohexyl phthalate and bis(2-ethylhexyl) phthalate in water samples. The mixture of ionic liquid (IL) and dispersive solvent was rapidly injected into 10 mL aqueous sample. Then, IL phase was separated by centrifugation and was determined by high-performance liquid chromatography-ultraviolet. The factors influencing the extraction efficiency, such as type and volume of IL, disperse solvent, extraction time, centrifuging time and ionic strength, were investigated and optimized. Under the optimized conditions, the extraction recoveries by the proposed ionic liquid-based dispersive liquid-liquid micro-extraction for the four phthalates ranged from 83.0 to 91.7%. The relative standard deviations were between 7.8 and 15%. The limits of quantification for four phthalates were between 10.6 and 28.5 μg/L. The proposed method was successfully applied for the analysis of PAEs in tap, lake and treated wastewater samples.     

Single‐drop microextraction followed by in‐syringe derivatization and GC‐MS detection for the determination of parabens in water and cosmetic products

A single‐drop microextraction (SDME) method followed by in‐syringe derivatization and GC‐MS determination has been developed for analysis of five parabens, including methyl, ethyl, isopropyl, n‐propyl and n‐butyl paraben in water samples and cosmetic products. N,O‐Bis(trimethylsilyl)acetamide (BSA) was used as derivatization reagent. Derivatization reaction was performed inside the syringe barrel using 0.4 μL of BSA. Parameters that affect the derivatization yield such as temperature and time of the reaction were studied. In addition, experimental SDME parameters such as selection of organic solvent, addition of salt, extraction time and extraction temperature were investigated and optimized. The RSD of the method for aqueous samples varied from 8.1 to 13%. The LODs ranged from 0.001 (n‐butyl paraben) to 0.015 (methyl paraben) μg/L, and the enrichment factors were between 23 and 150.     

Optimization of a single-drop microextraction procedure for the determination of organophosphorus pesticides in water and fruit juice with gas chromatography-flame photometric detection

A single-drop microextraction (SDME) procedure was developed for the analysis of organophosphorus pesticides (OPPs) in water and fruit juice by gas chromatography (GC) with flame photometric detection (GC-FPD). The significant parameters affecting the SDME performance such as selection of microextraction solvent, solvent volume, extraction time, stirring rate, sample pH and temperature, and ionic strength were studied and optimized. Two types of SDME mode, static and cycle-flow SDME, were evaluated. The static SDME procedure provided more sensitive analysis of the target analytes. Therefore, static SDME with tributyl phosphate (TBP) as internal standard was selected for the real sample analysis. The limits of detection (LODs) in water for the six studied compounds were between 0.21 and 0.56 ng/mL with the relative standard deviations ranging from 1.7 to 10.0%. Linear response data was obtained in the concentration range of 0.5-50 ng/mL (except for dichlorvos 1.0-50 ng/mL) with correlation coefficients from 0.9995 to 0.9999. Environmental water sample collected from East Lake and fruit juice samples were successfully analyzed using the proposed method, but none of the analytes in both lake water and fruit juice were detected. The recoveries for the spiked water and juice samples were from 77.7 to 113.6%. Compared with the conventional methods, the proposed method enabled a rapid and simple determination of organophosphorus pesticides in water and fruit juice with minimal solvent consumption and a higher concentration capability.     

Ionic liquid-based single drop microextraction of ultra-trace copper in food and water samples before spectrophotometric determination

In this work, room temperature ionic liquid (RTIL) 1-butyl-3-methylimidazolium hexafluorophosphate ([C4mim]PF6) was used as extractant in single drop microextraction (SDME). The traditionally volatile organic extractants were substituted by this green reagent, which changed SDME preconcentration into environmentally friendly method, relatively. After this pretreatment, ultra-trace copper in water and food samples could be accurately detected by spectrophotometer. This study was focused on the improvement of the analytical performance of spectrophotometric determination, expanding its applications. The influence factors relevant to IL-SDME, such as absorption spectra of complex, drop volume of RTIL, stirring rate and time, concentration of chelating agent, pH, and salt effect were studied systematically. Under the optimal conditions, the limit of detection (LOD) was 0.15 μg L(-1) with an enhancement factor (EF) of 33. The proposed method was green, simple, rapid, sensitive, and cost-efficient.     

Tetradecyl(trihexyl)phosphonium chloride ionic liquid single-drop microextraction for electrothermal atomic absorption spectrometric determination of lead in water samples

A highly efficient single-drop microextraction (SDME) procedure using a low-cost room temperature ionic liquid (RTIL), i.e., tetradecyl(trihexyl)phosphonium chloride (CYPHOS^® IL 101), for Pb determination at trace levels in real water samples was developed. Lead was chelated with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) reagent and extracted into a 4 μL microdrop of CYPHOS^® IL 101. The RTIL drop was directly injected into the graphite furnace of the electrothermal atomic absorption spectrometer (ETAAS). Under optimal microextraction conditions, a preconcentration factor of 32 was achieved with only 1.5 mL of sample resulting in a phase-volume ratio of 375. The limit of detection (LOD) obtained was 3.2 ng L⁻¹ and the relative standard deviation (RSD) for 10 replicates at 0.5 μg L⁻¹ Pb²⁺ concentration level was 4.9%, calculated at peak heights. The calibration graph was linear from concentration levels near the detection limits up to at least 4.5 μg L⁻¹ with a correlation coefficient of 0.9996. The accuracy of the methodology was evaluated by analysis of a certified reference material (CRM). The method was successfully applied to the determination of Pb in tap, mineral, well and river water samples.     

Magnetic ionic liquid assisted single‐drop microextraction of ascorbic acid before its voltammetric determination

For the first time, we coupled a microextraction technique using a magnetic ionic liquid with voltammetric determination. A hydrophobic magnetic ionic liquid that contains the tetrachloromanganate(II) anion, namely, aliquat tetrachloromanganate(II), was synthesized and used for the extraction of ascorbic acid from aqueous solutions followed by voltammetric determination. The extraction procedure was carried out using a single drop microextraction technique in which the ascorbic acid containing magnetic ionic liquid was separated with a magnet and then cast onto the surface of a carbon paste electrode modified with TiO₂ nanoparticles for the voltammetric quantification of the extracted ascorbic acid. Electrochemical quantification was carried out in a blank phosphate buffer solution. After optimizing different experimental conditions, a linear concentration range of 1.50–40.0 nM with a detection limit of 0.43 nM was obtained for the determination of ascorbic acid. The presented approach was successfully applied to the determination of ascorbic acid in samples of vitamin C effervescent tablets and orange juice.     

Simultaneous Analysis of Carbamate and Organophosphorus Pesticides in Water by Single-Drop Microextraction Coupled with GC–MS

Single-drop microextraction (SDME) has been coupled with gas chromatography–mass spectrometry to enable rapid and simple simultaneous analysis of carbamate and organophosphorus pesticides (OPP). The significant conditions affecting SDME performance (microextraction solvent, extraction time, solvent volume, sample pH, stirring speed, and ionic strength) were studied and optimized. Extraction was achieved by suspending a 1.5-μL drop of toluene from the tip of a microsyringe directly immersed in 5-mL aqueous donor solution at pH 5 stirred at 800 rpm. The dynamic linear range and detection limits of the method were evaluated by analysis of water samples spiked with carbamate pesticides and OPP. Under selected ion-storage mode, very low detection limits (0.02–0.50 ng mL^?1) and good linearity (0.5–200 ng mL^?1) were achieved. When SDME was applied to analysis of pesticides in natural water samples good recoveries (89.4–102.1%) were obtained. Inter-day and intra-day RSD of most results were below 5.4 and 6.1%, respectively. The method proved to be a rapid and simple tool for extraction and analysis of these pesticides in water samples.     

Ultrasound assisted ionic liquid dispersive liquid phase extraction of lovastatin and simvastatin: A new pretreatment procedure

A fast and novel sample preparation procedure: ultrasound assisted ionic liquid (IL) dispersive liquid extraction for the concentration of lovastatin and simvastatin in aqueous samples was developed. An IL ([C₆MIM][PF₆]) was used as the extraction solvent, and the factors affecting the extraction efficiency such as initial temperature, the volume of IL, pH of water samples, cooling time, and salt concentration were optimized. In combination with HPLC‐UV, both lovastatin and simvastatin exhibited a good linear range of 1–100 ng/mL. The limits of detection (LODs) of lovastatin and simvastatin were 0.17 and 0.29 ng/mL, respectively. Precisions of the proposed method (RSDs, n = 9) were 4.12 and 4.52%, respectively. This method has been successfully applied for the analysis of target compounds in three real water samples and good spiking recoveries were obtained in the range of 90.0–102.2% for lovastatin and 80.5–112.0% for simvastatin. These results indicated that ultrasound assisted IL dispersive liquid phase extraction would have good application prospect in the pretreatment of environmental samples.     

Liquid-phase microextraction for rapid AP-MALDI and quantitation of nortriptyline in biological matrices

A liquid-phase microextraction (LPME) method using a micropipette with disposable tips was demonstrated for coupling to atmospheric pressure MALDI-MS (AP-MALDI/MS) as a concentrating probe for rapid analysis and quantitative determination of nortriptyline drug from biological matrices including human urine and human plasma. This technique was named as micropipette extraction (MPE). The best optimized parameters of MPE coupled to AP-MALDI/MS experiments were extraction solvent, toluene; extraction time, 5 min; sample agitation rate, 480 rpm; sample pH, 7; salt concentration, 30%; hole size of micropipette tips, 0.61 mm (id); and matrix concentration, 1000 ppm using alpha-cyano-4-hydroxycinnamic acid (CHCA) as a matrix. Three detection modes of AP-MALDI/MS analysis including full scan, selective ion monitor (SIM), and selective reaction monitor (SRM) of MS/MS were also compared for the MPE performance. The results clearly demonstrated that the MS/MS method provides a wider linear range and lower LODs but poor RSDs than the full scan and SIM methods. The LOD values for the MPE under SIM and MS/MS modes in water, urine, and plasma were 6.26, 47.5, and 94.9 nM, respectively. The enrichment factors (EFs) of this current approach were 36.5-43.0 fold in water. In addition, compared to single drop microextraction (SDME) and LPME using a dual gauge microsyringe with a hollow fiber (LPME-HF) technique, the LODs acquired by the MPE method under MS/MS modes were comparable to those of LPME-HF and SDME but it is more convenient than both methods. The advantages of this novel method are simple, easy to use, low cost, and no contamination between experiments since disposable tips were used for the micropipettes. The MPE has the potential to be widely used in the future because it only requires a simple micropipette to perform all extraction processes. We believe that this technique can be a powerful tool for MALDI/MS analysis of biological samples and clinical applications.     

New temperature-assisted ionic liquid-based dispersive liquid–liquid microextraction method for the determination of glyphosate and aminomethylphosphonic acid in water samples

A new analytical temperature-assisted ionic liquid-based dispersive liquid–liquid microextraction (TA-IL-DLLME) method was developed for glyphosate and aminomethylphosphonic acid determination in water samples. Extracted analytes were derivatized using 9-fluoroenylmethylchloroformate and quantified by liquid chromatography with fluorescence detection. For the TA-IL-DLLME method, two strategies for phase solubilization were evaluated; in approach 1, the ionic liquid and aqueous matrix sample were mixed and then heated, while in approach 2, the aqueous sample was first heated and then the ionic liquid was injected. For both approaches, optimization included parameters that significantly affect extraction efficiency: ionic liquid type and volume, solubilization temperature and time, cooling and centrifugation time. Among the evaluated ionic liquids, 1-decyl-3-methylimidazolium tetrafluoroborate showed the best performance for TA-IL-DLLME and was selected for the two solubilization approaches; with approach 2, slightly better results were obtained. Thus, sample analyses were performed using a procedure based on approach 2. An important matrix effect, attributed to the presence of salts and metals in real water samples was observed. Sample acidification before derivatization allowed this problem to diminish, with recoveries ranging from 75 and 99%, and enrichment factors between 57 and 76 for target analytes.