Microcalorimetric Evaluation of Precipitation in Cu–2Be–0.2Mg

Beryllium precipitation from the Cu-rich matrix in a Cu–2 mass% Be–0.2 mass% Mg alloy homogenized and quenched from 1073 K was studied by differential scanning calorimetry (DSC). The DSC traces showed two main exothermic effects, A and B, each comprising two subeffects: A₁ and A₂ , and B₁ and B₂ respectively. Effects A₁ and A₂ correspond to the precipitation of GP zones and subsequent overlapping and independent precipitation of the phase. Only at very low heating rates can be inherited from GP zones. Effects B₁ and B₂ correspond to heat evolved during transitions to the states with and phases, respectively. Heat effect A can be quantitatively described in terms of solid solubilities before and after precipitation, and of the precipitation heats of the phases involved. The heat content of the combined GP zone/ phase precipitation effect was proportional to the number of beryllium atoms precipitated, yielding an average value of 21 kJ mol^–1 beryllium for beryllium precipitation. It was shown that the phase arises from the combined transition from states with GP zones and phases, whereas arises from the transition of states with and phases. The apparent activation energies associated with GP zones and , and phases are 1.16±0.08, 1.18±0.07, 1.37±0.08 and 1.74±0.09 eV, respectively. These values are discussed in terms of the mobility of dissolved atoms related to the concentrations of excess vacancies and solute-vacancy complexes, and the direction of plate-like precipitate growth (either normal or perpendicular to the plate). It is inferred that the main roles of magnesium are to decrease the amount and rate of GP formation, to enhance the volume fraction of and to suppress the discontinuous precipitation of .This revised version was published online in November 2005 with corrections to the Cover Date.     

Inclusion Complexes of Cyclodextrins with 4-Amino-1,8-Naphthalimides

The formation of inclusion complexes between 4-amino-1,8-naphthalimides and cyclodextrins (CDs) was investigated. The naphthalimides used in the study were 4-amino-1,8-naphthalimide (I) and4-(2-phosphonoethylamino)-N-(2-phosphonoethyl)-1,8-naphthalimide,tetraethylester (II). The CDs employed were -CD, -CD, -CD, HP--CD, HP--CD andHP--CD (HP = hydroxypropyl). Evidence for complex formation was obtained from the changes in the fluorescence spectra of the dyes in the presence of increasing amounts of the CDs. The most striking changes were observed with HP--CD and HP--CD. Treatment of the data using Benesi–Hildebrand plotswas consistent with a 1:1 inclusion model. The determined stabilityconstants were (K_eq, M^-1): 106 (I:HP--CD, pH = 2.0), 193 (I:HP--CD, pH = 7.0), 113 (I:HP--CD, pH = 7.0), 155(II:HP--CD, pH = 2.0), 121 (II:HP--CD,pH = 7.0), 301 (II:HP--CD, pH = 7.0). It can beconcluded that compound I forms a more stable complex with HP--CD than with HP--CD. Compound II, on the other hand, forms a more stable complex with HP--CD than with HP--CD.     

An empirical equation-of-state for solid-fluid interfacial free energies

The contact angle,, formed by a liquid on a solid surface in air depends on the solid-air ( _S ), liquid-air ( _L ) and solid-liquid ( _SL ) interfacial free energies, as described by Young's equation. Critical examination of reported contact angles for numerous liquids and solids leads to an empirical correlation between _sL and both _Y and _S . Combination of this correlation with Young's equation gives an empirical relation allowing calculation of _S from _L and Calculations made with these empirical relations agree well with estimations of _S obtained by the method of critical spreading, and are consistent with Young's equation.Founded and supported by F. Hoffmann-La Roche and Co., Limited Company, Basel, Switzerland.     

The predictive accuracy for estimating infinite dilution activity coefficients by γ∞-based UNIFAC

The predictive accuracy for estimating infinite dilution activity coefficients by a modification of the UNIFAC method wherein the group interaction parameters were based on only data (referred to as -based UNIFAC) has been studied. Estimates and measured values were compared for six prototypical solutes in a series of homologous n-alkanes, l-alcohols and alkanenitrile solvents. Despite the fact that the interaction parameters were derived using only data, this approach still gave serious errors due to several inherent problems in the original UNIFAC model. Its performance is sometimes even poorer than that of the original UNIFAC method. For example for nitromethane in alcohols and p-dioxane in nitriles values predicted by the -based UNIFAC are essentially zero. The large errors for these systems are most likely due to inaccurate interaction parameters in the -based UNIFAC method.     

Methane Adsorption and Plasma-Assisted Catalytic Conversion on the Surface of γ-Alumina

Diffuse scattering IR spectroscopy was applied to study the adsorption and plasma-assisted catalytic conversion of methane (deuteromethane) on the surface of -alumina. It was found that CH₄ adsorption sites on the -Al₂O₃ surface were formed by molecular and dissociative mechanisms under the action of an electric-discharge plasma at room temperature. As distinct from -radiolysis, plasma treatment leads to the formation of acetylene in addition to other hydrocarbon products, aluminum hydrides, and surface hydroxyl groups. Plausible mechanisms were proposed for plasma-assisted catalytic reactions in the -Al₂O₃–adsorbed CH₄(CD₄) system.     

Cohesion of crystals and the temperature coefficient of their equilibrium surface pressure

Summary Surface tension _e of mercury in equilibrium with crystals (floating on its surface) of octacosane, 1-hexadecanol, 1-octadecanol, ethyl palmitate, benzophenone and azoxybenzene at 7° is almost equal to that at 23° (measured earlier); also the difference between the surface tension ( ₀) of uncontaminated mercury and _e (i. e., equilibrium surface pressure) is independent of temperature within the limits of the experimental error. This shows that the hypothesis making ₀- _e an analog of the vapor pressure of the solid is incorrect. The relation _e= (=cohesion of the crystal,=thickness of the surface layer of mercury) is in agreement with the negligible temperature coefficient of _e . The calculated is approximately 9 angstroems.

---

Zusammenfassung Die Oberflächenspannung _e von Quecksilber im Gleichgewicht mit Kristallen (schwimmend auf der Oberfläche) von Octosane, 1-hexadecanol, 1-octodecanol, Äthylpalmitat, Benzophenon und Azoxylbenzol bei 7 °C ist nahezu gleich der bei23 °C gemessenen. Auch die Differenz der Oberflächenspannung von reinstem Quecksilber ( ₀) und ( _e), d. h. dem Gleichgewichtsobderflächendruck ist unabhängig von der Temperatur innerhalb der experimentellen Fehlergrenze. Dies zeigt, daß die Hypothese, nach der man ₀- _e in Analogie zum Dampfdruck des Festen betrachtet, unkorrekt ist. Die Beziehung _e= (=Kohäsion des Kristalls,=Dicke des Oberflächenfilms auf Quecksilber) ist in Übereinstimmung mit dem vernachlässigbaren Temperaturkoefifzienten von _e. Das berechnete beträgt ungefähr 9 Å.

     

Fast non-destructive determination of silicon in coal by means of /n,n′ γ/ and /n, γ/ processes

The possibilities were evaluated of nondestructive determination of silicon content in large-scale samples of coal /about 20–50 kg/, based on the spectrometry of prompt -radiation from processes /n, n /, E=1779 keV and /n, /, E=3539 keV and 4935 keV. The neutron sources were either²⁴¹Am–Be or²⁵²Cf located additionally in D₂O moderator. A Ge/Li/ detector was used for -radiation detection. In exposure times of up to 2 h, the detection limits of 1.3% and 0.9% and accuracies of silicon determination of 0.66% and 0.40% have been achieved in case of /n, / and /n, n / processes, respectively.     

Intercalation of porphyrin (TMPyP) and copper-porphyrin into γ-zirconium phosphate

Water-soluble ,,,-tetrakis(4-N-methylpyridyl)porphine(TMPyP) was directly intercalated into -zirconium phosphate (-ZrP) with expansion of the interlayer distance from 12.3 to a maximum of 17.2 Å, indicating parallel orientation of porphyrin to the layer of -ZrP. Diffuse reflectance spectra of the intercalate shows that the porphyrin is protonated in the interlayer space. Uptake of Cu²⁺ ions into the porphyrin intercalate takes place with further increase in the interlayer distance. It was observed that TMPyP metalated Cu²⁺ in -ZrP. Copper porphyrin can also be taken up quite easily and an interlayer spacing of 18.6 Å is attained.     

Synthesis of organocyclosiloxanes containing cyanoalkyl groups on the silicon atom

The cohydrolysis of-cyanoethyl- and-cyanopropylmethyldichlorosilanes with dimethyldichlorosilane has been studied and the optimum conditions ensuring the maximum yield of rings containing cyanoalhyl groups have been determined.B is(-cyanoethyl)hexamethylcyclotetrasiloxane,-cyanopropylpentamethylcyclotetrasiloxane, and bis(-cyanopropyl)hexamethylcyclotetrasiloxane have been obtained for the first time and characterized.     

Efficiency calibration and summation effects in gamma-ray spectrometry

Precise, absolute -ray efficiences ( ) and total efficiences ( _T), have been measured at various distances from the detector, using a set of standards. The observed linear variation of and _T as well as / _T with E and provides a simple means of interpolation and extrapolation. Experimental coincidence summation effects were determined for various nuclides and compared with calculated values. The results are found to be in good agreement with each other.     

Solubility Study of Nimodipine Inclusion Complexation with α- and β-Cyclodextrin and some Substituted Cyclodextrins

The solubility of nimodipine was measured in aqueous solutions of the following cyclodextrins: -cyclodextrin (-CD), hydroxypropyl--CD (HP--CD), -cyclodextrin (-CD), random substituted methyl--CD (M--CD), three hydroxypropyl--CDs (HP--CD) with mutually different average degree of substitution, and hydroxypropyl--cyclodextrin (HP--CD). From the determined linear solubility diagrams the values of the binding constant K₁₁ of the inclusion complexes of nimodipine with the respective CDs were evaluated. The -CDs efficiently solubilized sparingly soluble nimodipine, the highest value of K₁₁ was found for M--CD (1680 M^-1), followed by -CD (550 M^-1) and HP--CDs, where the higher degree of substitution lowered K₁₁. Only slight solubilization of nimodipine was observed in the solutions of the -CDs and HP--CD.     

Dissociative electron capture and level width of quasistationary molecular states

Perturbation theory is applied to give the cross section for dissociative capture e+A₂A+A^–. From the requirement of quantitative agreement with experiment, the level widths for the quasistationary states are estimated as ₁1.2 eV; ₂0.2 eV; ₃0.05 eV for the first three terms for H ₂ ^– .Visiting worker from the Boris Kidri Institute of Nuclear Sciences, Belgrade.     

Aqueous solubilities and octanol-water partition coefficients of binary liquid mixtures of organic compounds at 25°C

From thermodynamics and certain assumptions it is shown that, under the usual experimental conditions, the octanol-water partition coefficient (K_o/w) of a given organic liquid should be the same whether the substance is partitioned neat or as part of a mixture. Measurements of several mixtures of n-propylbenzene (log K_o/w=3.71±0.04)+ethylbenzene (log K_o/w=3.16±0.01) clearly confirm this. It is also shown that the aqueous solubility (S_w) of a neat organic liquid can be related to its aqueous solubility (S _w ), when it is present at volume fraction in an organic liquid mixture, by S _w =S_w, where is its activity coefficient in the organic mixture. The measured S _w values for n-propylbenzene + ethylbenzene (1), n-hexane + nitrobenzene (>1) and di-isopropyl ether + chloroform (<1) are found to be in good agreement with the predicted values (average differences of, respectively, <2%, 8% and 6%). In general, the bounds on S _w are expected to be 0w w.     

Determination of solid solution limits based on the thermal behaviour of aluninium substituted iron hydroxides and oxides

The formation of substitutional solid solutions of the isostructural oxyhydroxides -FeOOH--AlOOH (goethite-diaspore and -FeOOH--AlOOH (lepidocrocite-boehmite) was investigated by X-ray powder diffraction technique and by thermal analysis.The unit cell parameters of both orthorhombic structures of -Fe_1–x-Al_xOOH (Pbnm) and -Fe_1–xAl_xOOH (Cmcm) decrease clearly with the increase of aluminium content up tox=0.10.Thermal analysis reveals the sensitivity of DTA and DTG effects to the composition of solid solutions. The temperatures of topotactic formation of rhombohedral -(Fe, Al)₂O₃ and of the defect-spinel -(Fe, Al)₂O₃ during the dehydroxylation of -(Fe, Al)OOH and -(Fe, Al)OOH respectively increase as the aluminium concentration rises up to 10 mol%. The dehydration curves of samples with greater aluminium content exhibits the same maximumm/T as for the 10 mol% Al-preparation, indicating indirectly the end-members of the solid solution ranges.

---

Zusammenfassung Mittels Röntgendiffraktion und Thermoanalyse wurde die Bildung von Substitutions-Mischkristallen der isostrukturellen Oxyhydroxide -FeOOH--AlOOH (Goethit-Diaspor) und -FeOOH--AlOOH (Lepidokrokit-Böhmit) untersucht. Die Elementarzellenparameter beider rhombischer Strukturen von -Fe_1–xAl_xOOH (Pbnm) und -Fe_1–xAl_xOOH (Cmcm) werden mit zunehmenden Aluminiumgehalt bis zux=0.10 eindeutig kleiner.Thermoanalyse zeigt die Empfindlichkeit von DTA- und DTG-Effekten gegenüber der Zusammensetzung der Mischkristalle. Steigt die Aluminiumkonzentration bis 10 mol% an, so erhöhen sich auch die Temperaturen für die topotaktische Bildung von rhomboedrischem -(Fe,Al)₂O₃ und des Defekt-Spinells -(Fe,Al)₂O₃ bei der Dehydroxylierung von -(Fe,Al)OOH und -(Fe,Al)OOH. Die Dehydratationskurven von Proben mit einem größeren Aluminiumgehalt zeigen dasselbe m/T-Maximum wie für die Proben mit 10 mol%, was indirekt auf die Grenze des Mischkristallbereiches deutet.

     

Comparison of the Complexation of Cosmetical and Pharmaceutical Compounds with γ-Cyclodextrin, 2-Hydroxypropyl-β-cyclodextrin and Water-Soluble β-Cyclodextrin-co-epichlorhydrin Polymers

The ability of different cyclodextrins (CDs): CD, 2-hydroxypropyl CD to complex drugs like 3--hydroxy-11-oxoolean- 12-en-30-oic acid, 2-ethylhexyl-3-(4-methoxyphenyl)-2-propanoate and menthol was compared to that of water-soluble polymers: CD-co-epichlorhydrin polymer (pCD/EP) and CD-co-epichlorhydrin polymer partially modified with trimethylammonium groups (pCD/EPN⁺). 3--Hydroxy-11-oxoolean-12-en-30-oic acid was poorly solubilized by CD compared with other CD derivatives, however the determination of the complexation constants was possible for pCD/EP, K₁₁ = 740, K₁₂ = 4, for pCD/EPN⁺, K₁₁ = 681, for CD, K₁₁ = 16 and for hydroxypropyl CD, K₁₁ = 114, K₁₂ = 3.4. A significant increase of the solubility was observed for 2-ethylhexyl-3-(4-methoxyphenyl)-2-propanoate with all host molecules, it was 916 times its solubility in pure water with pCD/EPN⁺, 1116 and 1300 times with 2-hydroxypropyl CD and pCD/EP respectively. The association constants are K₁₁ = 7970, K₁₁ = 4700, K₁₁ = 1470, K₁₁ = 230 and K₁₂ = 200 with pCD/EP, pCD/EPN⁺, CD, 2-hydroxypropyl CD respectively. An increase of the solubility of menthol was observed with all CD derivatives, up to 36–37 times, except for CD. The complexation constants are similar equal to about 200.     

Mass spectrometric study of monoalkyl-substituted thiacyclanes

Monosubstituted - and -alkylthiophans and -, -, and -alkylthiacyclohexanes were subjected to a comparative mass spectrometric study. The stability of the M⁺ ion increases on passing from - to -alkylthiophans and from - to - and -alkylthiacyclohexanes. In the case of -alkylthiophans and - and -alkylthia-cyclohexanes the principal process is associated with ejection of the substituent as a whole, whereas a portion of the alkyl substituent, with retention of one CH₂ group in the composition of the charged fragment, is eliminated from the molecular ions of -alkylthiophans and -alkylthiacyclohexanes.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 2, pp. 176–181, February, 1978.     

Condensation of 2-(1-ethoxyvinyl)oxiranes with sodiomalonic ester and decarboxylation of the reaction products obtained

-(1-Ethoxyvinyl)- and -(1-ethoxyvinyl)--ethoxycarbonyl--butyrolactones were obtained by the reaction of 2-(1-ethoxyvinyl)oxiranes with sodiomalonic ester. Decarboxylation of the -(1-ethoxyvinyl)--ethoxycarbonyl-butyrolactones in DMSO leads to -(1-ethoxyvinyl)--butyrolactones, the hydrolysis of which gives -acetyl-butyrolactones. Ethyl trans-3-acetyl-3-pentenoate was obtained by decarboxylation of -methyl--(1-ethoxyvinyl)--ethoxycarbonyl--butyrolactone in DMSO.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 1, pp. 22–25, January, 1992.     

Effect of ageing atmospheres on the changes in surface free energies of oxygen plasma-treated polyethylene films

The changes in the surface properties of oxygen plasma-treated polyethylene films during ageing in various atmospheres (water, dry nitrogen gas, and hexane) were studied from the viewpoint of the interaction of the surface functional groups formed on the films and the ageing media. The XPS (x-ray photoelectron spectroscopy) and the SSIMS (static secondary ion mass spectrometry) spectra indicated the formation of polar groups containing oxygen such as C=O on the film surface. The changes in the critical surface tension (_C) of the film with ageing time were largely affected by the ageing atmospheres: the _C value of the film aged in water increased, and those of the films aged in nitrogen gas and hexane decreased with an increase in ageing time. These different tendencies among the ageing media could be understood reasonably with examining the surface free energy ratios (the total energy, _S ^tot , the dispersion force component, _S ^d / _S ^tot , the polar component, _S ^p / _S ^tot , the hydrogen bonding component, _S ^h / _S ^tot ) of the films. The ageing in water of which _L is large gave the films with higher _S ^p / _S ^tot values, suggeting that the overturn and/or the orientation of the polar groups toward the water phase occurred so as to minimize the discrepancy of the surface free energy between the polymer surface and water. On the other hand, the ageing in nitrogen gas and hexane media of which _L are small gave the films with lower _S ^p / _S ^tot and _S ^h / _S ^tot values, suggesting the overturn and/or the orientation of the polar groups into the bulk polymer.     

Preparation,characterization of crystalline zirconium phosphates and study on their acid stability and ion exchange behavior with uranyl ions

Two kinds of crystalline zirconium phosphate, - and -ZrP were prepared by direct method, and characterized by means of X-ray powder diffractometry, thermogravimetric analysis and pH titration. The total exchange capacity of -ZrP and -ZrP for Na⁺ ions determined by pH titration was 8.80 mmol/(g Zr(HPO₄)₂·6H₂O) and 3.80 mmol/(g NH₄ZrH(PO₄)₂·H₂O), respectively. The thermodynamic equilibrium constant of exchange reactions on -ZrP and on -ZrP at 25.0°C is 2.5 and 1.1, respectively. Although UO ₂ ²⁺ in solution is more preferred by -ZrP than by -ZrP, the selectivity of -ZrP for UO ₂ ²⁺ decreases with decreasing pH value while less effect of pH on the amount of UO ₂ ²⁺ ions exchanged to -ZrP has been found. It is also interesting to find out that both H⁺ and NH ₄ ⁺ ions in -ZrP can be replaced by UO ₂ ²⁺ ions existed in concentrated solution.     

Phase solubility analysis in studying the interaction of nifedipine with selected cyclodextrins in aqueous solution

The solubilizing potential and complexing tendencies of six cyclodextrins (CyD) with nifedipine in aqueous solution were evaluated using phase solubility methods. Solubility curves of nifedipine with -CyD, 2-hydroxypropyl--CyD (2HP--CyD) and 2-hydroxypropyl--cyclodextrin (2HP--CyD) were classified as type A_L, while for heptakis (2,6-dimethyl)--CyD (DIMEB), randomly methylated--CyD (RAMEB) and -CyD, A_p type phase behaviour was observed. Stability constants, calculated from phase solubility diagrams, decreased in the order: DIMEB > RAMEB > -CyD > 21HP--CyD > -CyD > 2HP--CyD.