Nd：YAG激光治疗机计算机光反馈控制技术

本文讨论了Ｎｄ；ＹＡＧ激光治疗机的计算机光反馈技术以及可控要素的确定。提高了激光输出的稳定性。预置功率误差３％，激光输出功率不稳定度±２％。     

High power Nd:YAG slab laser sidepumped by diode laser array

ＨｉｇｈｐｏｗｅｒＮｄ：ＹＡＧｓｌａｂｌａｓｅｒｓｉｄｅｐｕｍｐｅｄｂｙｄｉｏｄｅｌａｓｅｒａｒｒａｙＣＨＥＮＹｏｕｍｉｎｇ；ＺＨＯＵＦｕｚｈｅｎｇ；ＨＵＷｅｎｔａｏ；ＬＩＺｈｉｓｈｅｎ；ＹＡＮＧＸｉａｎｇｃｈｕｎ；ＷａｎｇＺｈｉｊｉａｎｇ（Ｓｈａｎ...     

光反馈诱发长波长垂直腔面发射激光器低功耗偏振开关

基于扩展的自旋反转模型,对光反馈诱发下长波长垂直腔面发射激光器中的低功耗偏振开关进行了理论研究.研究表明:长波长垂直腔面发射激光器在自由运行下未能获得的偏振开关现象,可以通过引入中等强度的偏振旋转光反馈来实现.对比强弱两种不同的线性色散效应,发现了一些有趣的现象:弱线性色散条件下更易于在低注入电流下获得偏振开关,并且产生偏振开关所需的反馈强度具有更大的调控范围;强色散效应中未能始终获得偏振开关,会出现两模共存区,并且偏振开关出现的注入电流值较高.同时,观察到的偏振模跳变和多偏振开关现象类似于短波长垂直腔面发射激光器,因而证实这两类激光器在偏振开关的本质规律上是相似的.此外,还对长波长垂直腔面发射激光器不易在低注入电流下获得偏振开关的原因进行了分析,并给出了合理的解释.     

Mode hopping in single-mode microchip Nd：YAG lasers induced by optical feedback

The mode hopping phenomenon induced by optical feedback in single-mode microchip Nd：YAG lasers is presented. With optical feedback, mode hopping strongly depends on two factors： the ratio of external cavity length to intra-cavity length, and initial gains of the two hopping modes, When external cavity length equals an integral multiple of intracavity length, there is almost no mode hopping. However, if the external cavity length does not equal an integral multiple of intra-cavity length, mode hopping occurs. The ratio of external cavity length to intra-cavity length determines the position of two-mode hopping, The initial gains of the two hopping modes determine the corresponding peak values and oscillating periods of them in the intensity modulation curves.     

微片Ｎｄ∶ＹＡＧ 双频激光器腔调谐现象研究

 基于微片Ｎｄ∶ＹＡＧ 正交偏振双频激光器,研究了若干重要的双频激光器腔调谐现象, 包括光强调谐、频差调谐、子谐振腔效应及频差闭锁等,给出了实验结果和数据。腔调谐下,正交双频的频差调谐量约为３５０ ｋＨｚ;存在子谐振腔效应时,频差调谐量最大可达到２ ＭＨｚ;未发现明显频差闭锁现象,频差最小值可达到１４ ＭＨｚ。     

1550nm-VCSELs在偏振保持光反馈和正交光注入下的偏振转换特性

基于自旋反转模型,研究了1550 nm垂直腔面发射激光器(1550 nm-VCSELs)在偏振保持光反馈和正交光注入下的偏振转换特性.结果表明:正交光注入下的从激光器会随着注入强度的增加产生偏振转换.在归一化注入电流较小时,改变反馈强度,会使从激光器发生偏振转换的注入强度出现规律不同的变化;改变频率失谐,会使从激光器发生偏振转换的注入强度出现规律相同的变化.     

External-cavity birefringence feedback effects of microchip Nd:YAG laser and its application in angle measurement

External-cavity birefringence feedback effects of the microchip Nd:YAG laser are presented. When a birefringence element is placed in the external feedback cavity of the laser, two orthogonally polarized laser beams with a phase difference are output. The phase difference is twice as large as the phase retardation in the external cavity along the two orthogonal directions. The variable extra-cavity birefringence, caused by rotation of the external-cavity birefringence element, results in tunable phase difference between the two orthogonally polarized beams. This means that the roll angle information has been translated to phase difference of two output laser beams. A theoretical analysis based on the Fabry--Perot cavity equivalent model and refractive index ellipsoid is presented, which is in good agreement with the experimental results. This phenomenon has potential applications for roll angle measurement.     

高功率四波长Nd:YAG激光实验

四波长Nd：YAG激光实验是利用非线性晶体BBO，通过倍频、混频和二次倍频等激光变频技术，分别获取了4个波段相干辐射光，本文介绍了各波长相干辐射光的获取方法及其时空特性的测量。     

1.15 kW连续波全固态Nd:YAG激光器

研制了五组双线二极管列阵侧面泵浦Nd: YAG棒的高效率、高功率激光头。将一块90° 石英旋光片插入两个这样的激光头中间并置入热近非稳对称平平腔，产生了1157 W高光束质量（M2 ~ 39）1064 nm连续波输出，据我们所知，这是侧面泵浦双棒Nd: YAG激光器产生的最高功率。     

Nd：YAG激光器中的自锁模

本文报道在Nd:YAG激光器中首次获得的自锁模脉冲序列.自锁模是由于Nd:YAG棒中的自相位调制引起的.在主被动对撞锁模运转情况下,自锁模对脉冲波形有较大的影响.     

调频微片Nd:YAG激光器光回馈特性的研究

研究了调频微片Nd：YAG激光器的光回馈特性.在没有光回馈的情况下，激光频率每改变一个纵模间隔，激光器输出功率变化一个条纹.有光回馈时，同时改变激光频率和外腔相位，激光器输出功率波动频率正比于内、外腔长度之比.基于三镜腔等效模型的理论分析和实验结果相符合.并且讨论了这一现象在精密测量领域的潜在应用.     

LD泵浦Nd:YAG微片激光器

ＬＤ泵浦Ｎｄ：ＹＡＧ微片激光器结构简单紧凑，与半导体激光器相比，前者具有激光线宽窄、光束质量好、相干长度长等优点，因此在一些测量领域有着较好的应用前景。目前对ＬＤ泵浦Ｎｄ：ＹＡＧ微片激光器的实验工作主要是获得单频、单模连续输出和线性频率调制特性研究。本文综述了近几年来ＬＤ泵浦Ｎｄ：ＹＡＧ微片激光器的研究方向、成果及应用，主要介绍了各国对ＬＤ泵浦Ｎｄ：ＹＡＧ微片激光器的调频特性的研究状况     

透明Nd:YAG激光陶瓷的研究与应用进展

综述了近年来,特别是近两年来国内外透明Nd:YAG激光陶瓷的研究与应用情况,重点对我国的透明Nd:YAG激光陶瓷研究近况进行了分析,指出了透明Nd:YAG激光陶瓷是目前陶瓷研究的热点。提出了透明Nd:YAG激光陶瓷研究中尚存在的问题和我国在此领域中与国外研究的巨大差距。分析指出:我国研究透明Nd:YAG激光陶瓷的各个院所之间,应该强强联合,优势互补,对该领域的理论和制备工艺进行更为深入的研究。     

Compact 600 mW blue laser with a composite Nd:YAG

A compact and simple design for an LDA-end-pumped intracavity doubling high-power blue laser with a composite Nd:YAG laser on the ⁴F_3/2 to ⁴I_9/2 laser transition in a flat-curved cavity is demonstrated. The nonlinear crystal used in the experiment is an LBO crystal cut for phase-matching type I. Through the thermo-lensing effect of the laser crystal at high-pumped power, the optimum mode-matched and efficient intracavity doubling are realized at the same time. The maximum output power at 473 nm was 600 mW when the absorbed, pumped power of 15 W, and the optical-to-optical conversion efficiency is 4%. The stability of blue output power is 3.2% within 2 h.     

高平均功率调Q准连续Nd:YAG激光器

通过选用低掺杂浓度的Nd:YAG晶体棒、热近非稳腔优化设计、双棒串接热致双折射补偿技术以及双Q开关正交放置结构，在LD抽运功率1116W时，实现调Q准连续全固态Nd:YAG激光器1064nm输出，平均功率达258W，光束质量M²～15.5，重复频率为10kHz，脉冲宽度为64ns，峰值功率达0.4GW，光光转换效率达23.1%. 关键词： Nd:YAG激光器 准连续波 激光二极管抽运 固体激光器     

Solar pumped Nd:YAG laser

We report the high efficiency of solar pumped laser. The sunlight is concentrated by the concentrator system, which is composed by the Fresnel lens and the cone-channel condenser. The power density of sunlight concentrated by the concentrator system surpasses the lasing threshold for pumping laser. In the experiment, the sunlight concentrated is coupled into the conical chamber pumping Nd:YAG laser media. Laser output of 3.5 W has been achieved; the collect efficiency is 3.5 W/m². The conversion efficiency is 1.0% from solar power into laser, and the slope efficiency is achieved 1.86%.     

Frequency-tripled Nd:YAG laser ablation in laser structuring process

With the increasing demand for finer lines/spaces on PCB boards, a new technology—laser structuring—has emerged in recent years. In this research, the frequency-tripled Nd:YAG laser is selected as the laser source in laser structuring; this laser is often used in miniaturization machining. This paper describes in detail the processing parameters’ influences, such as laser power, numbers of repetition, repetition rate and bite size, on laser structuring results. From the research results, it can be concluded that the line width and depth are increased with increases in the laser power and numbers of repetition. Repetition rate, bite size and velocity are related to one another. When the bite size is fixed, the velocity increases with the repetition rate and the depth of the line is decreased at the same time. When the repetition rate is fixed, velocity increases with the bite size.     

Compact corner-pumped Nd:YAG/YAG composite slab laser

Corner-pumping is a new pumping scheme in diode-pumped all-solid-state lasers, having such advantages as high pump efficiency, favorable pump uniformity and low cost. Compact corner-pumped Nd:YAG/YAG composite slab lasers at 1064 nm with low or medium output powers and high efficiency are demonstrated in this paper. Combined with intracavity frequency doubling by a LBO crystal, a corner-pumped Nd:YAG/YAG composite slab 532 nm green laser with a stable output is realized successfully. The experimental results show that corner-pumping can reduce laser costs greatly, release the thermal effects of slab crystals and improve the output beam quality, and that the new pumping scheme is feasible in the design of diode-pumped all-solid-state lasers with low or medium output powers.     

Distortion of optical feedback signals in microchip Nd:YAG lasers subjected to external multi-beam interference feedback

This paper proposes a theoretical analysis for the characteristics of an external cavity Nd:YAG laser with feedback of multiple-beam interference, which is induced by the multi-reentrance of the light from the external Fabry--Perot cavity. The theoretical model considers the multiple beam interference of the external Fabry--Perot cavity. It is found that the optical feedback signals are distorted to pulse waveforms instead of the sinusoidal ones in conventional feedback. The experimental results are in good agreement with the theoretical analysis. The obtained theoretical and experimental results can advance the development of a laser feedback interferometer.     

Experimental study of high-power pulse side-pumped Nd:YAG laser

The paper reports on the characterization of a compact and simple side-pumped 0.538 J×100 Hz pulse Nd:YAG laser. A side-pumping configuration with 100 laser diode bars is used in the laser head. We also experimentally studied the laser performance of the diode-pumped Nd:YAG laser head in the free running and Q-switched operation under different repetition rates.