Comparison of the performance of different reversed-phase columns for liquid chromatography separation of 11 pollutant phenols

A systematic optimization of the HPLC separation of a mixture containing 11 pollutant phenols (PPs) using a Hypersil ODS (250 mm x 4.6 mm, 5 microm) column and UV-DAD detection has been carried out. The binary mobile phases used were obtained by mixing 50 mM phosphate (pH = 3.0) and methanol, ACN, or THF as organic modifiers. After selecting ACN as an organic modifier, the effects of pH and temperature on PPs separation were studied. A mobile phase of 50 mM acetate (pH = 5.0)-ACN (60:40 v/v) at 50 degrees C allowed the separation of 11 phenols but not to baseline in 17 min. To improve the performance of this separation, the following RP columns were tested: Luna C18 (2), Purospher C18, Synergi C12, Synergi Fusion C18, Gemini C18, Luna Cyano, Lichrospher C8, and Envirosep-PP (polymeric). In all the cases, the performance (analysis time, retention, selectivity, resolution, asymmetry factors, and efficiency) was evaluated. A further reoptimization of the mobile phase was carried out for all the columns by studying the ACN content and pH, with the aim of improving the above-mentioned separations and selecting the most suitable one for PPs analysis.     

Quantification of Fumaria officinalis isoquinoline alkaloids by nonaqueous capillary electrophoresis-electrospray ion trap mass spectrometry

A capillary electrophoresis (CE) method using non-aqueous (NA) separation solutions combined with an ion trap mass spectrometer (MS and MS/MS) as detection device is presented for the separation, identification and quantification of isoquinoline alkaloids from Fumaria officinalis. The best results were obtained with a mixture of acetonitrile-methanol (9:1, v/v) containing 60mM ammonium acetate and 2.2M acetic acid as running electrolyte and an applied voltage of 30 kV. Electrospray MS measurements were performed in the positive ionization mode with isopropanol-water (1:1, v/v) as sheath liquid at a flow rate of 3 microl/min. Alkaloids were detected as [M+H](+)-ions and showed typical fragmentation patterns in MS/MS experiments. The developed assay was used for the quantification of seven isoquinoline alkaloids representing different structural subtypes in Fumariae herba extracts and F. herba containing phytopharmaceuticals.     

A generic approach to the impurity profiling of drugs using standardised and independent capillary zone electrophoresis methods coupled to electrospray ionisation mass spectrometry

Three standardised, capillary zone electrophoresis-electrospray ionisation mass spectrometry (CZE-ESI-MS) methods were developed for the analysis of six drug candidates and their respective process-related impurities comprising a total of 22 analytes with a range of functional groups and lipophilicities. The selected background electrolyte conditions were found to be: 60/40 v/v 10 mM ammonium formate pH 3.5/organic, 60/40 v/v 10 mM ammonium acetate pH 7.0/organic and 10 mM piperidine, pH 10.5, where the organic solvent is 50/50 v/v methanol/acetonitrile. The coaxial sheath flow consisted of either 0.1% v/v formic acid in 50/50 v/v methanol/water, or 10 mM ammonium acetate in 50/50 v/v methanol/water, depending on the mixture being analysed. Factor analysis and informational theory were used to quantify the orthogonality of the methods and predict their complementarities. The three selected CZE-ESI-MS methods allowed the identification of 21 out of 22 of all the drug candidates and their process-related impurities and provided orthogonality with four established high-performance liquid chromatography-mass spectrometry (HPLC-MS) methods. These methodologies therefore form the basis of a generic approach to impurity profiling of pharmaceutical drug candidates and can be applied with little or no analytical method development, thereby offering significant resource and time savings.     

Capillary electrochromatography-mass spectrometry of cationic surfactants

The CEC-MS of alkyltrimethylammonium (ATMA+) ions with chain lengths ranging from C1-C18 is optimized using an internally tapered column packed with mixed mode reversed phase/strong cation exchange stationary phase. A systematic study of the CEC separation parameters is conducted followed by evaluation of the ESI-MS sheath liquid and spray chamber settings. First, the optimization of CEC separation parameters are performed including the ACN concentration, triethylamine (TEA) content, buffer pH and ammonium acetate concentration. Using 90% v/v ACN with 0.04% v/v TEA as mobile phase, the separation of longer chain C6-C18-TMA+ surfactants could be achieved in 15 min. Lowering the ACN concentration to 70% v/v provided resolution of shorter chain C1, C2-TMA+ from C6-TMA+ although the total analysis time increased to 40 min. Furthermore, variation of both the ACN and TEA content as well as ionic strength has found to significantly influence the retention of longer chain surfactants as compared to shorter chains. The optimum CEC conditions are 70% v/v ACN, 0.04% v/v TEA, pH 3.0 and 15 mM ammonium acetate. Next, the optimization of the ESI-MS sheath liquid composition is conducted comparing methanol to isopropanol followed by the use of experimental design for analysis of spray chamber parameters. Overall, the developed CEC-ESI-MS method allows quantitative and sensitive monitoring of ATMA+ from < or =10 microg/mL down to 10 ng/mL. Utilizing the optimized CEC-ESI-MS protocol, the challenging analysis of commercial sample Arquad S-50 ATMA+ containing cis-trans unsaturated and saturated soyabean fatty acid derivatives is demonstrated.     

Novel nonaqueous capillary electrophoresis separation and determination of bioactive flavone derivatives in Chinese herbs

Nonaqueous CE (NACE) coupled to UV detection is described for the separation and determination of bioactive flavone derivatives in Chinese herbs extraction. After optimization of electrophoresis parameters, including the electrolyte nature and the organic solvent composition, a reliable separation of the analytes in an ACN/methanol (60:40, v/v) mixture containing 80 mM Tris and 10 mM sodium cholate was performed. The detection was performed at 254 nm. Method performances, including migration time and peak area reproducibility, linearity, sensitivity, and accuracy, were evaluated. The method was applied to determine bioactive flavone derivatives in seven Chinese herbs.     

A new high-performance liquid chromatographic method with evaporative light scattering detector for the analysis of phospholipids. Application to Iberian pig subcutaneous fat

A new method for the analysis of phospholipids by normal-phase HPLC is described using a silica column. Addition of ammonia and triethylamine to a gradient based on chloroform/methanol/water promoted a good and rapid separation of phospholipid classes (20 min run). The use of an evaporative light scattering detector permitted an accurate analysis of a mixture of phospholipids. Calibration curves were linear within different range for each phospholipid class. The LOD and LOQ obtained were below 0.03 and 0.05 mg kg⁻¹ for all cases, respectively. Besides, a new method for the separation of phospholipids from total lipids before HPLC analysis by a solid-phase extraction (SPE) with Si cartridges has been developed. This methodology gave a good recovery ranging from 97 to 117%. The method was validated with a standard mixture of phospholipids. This method has been applied to characterize the phospholipid fraction of subcutaneous fat from Iberian pig. Cardiolipin, phosphatidylethanolamine, phosphatidylinositol, phosphatidylserine, phosphatidylcholine, and sphingomyelin have been described for first time in these samples. The fatty acid composition of the different phospholipid classes and their HPLC electrospray ionization mass spectrometry have been used for characterizing the molecular species present in each one.     

Nonaqueous capillary electrophoresis with laser-induced fluorescence detection: a case study of comparison with aqueous media

A novel method based on separation by nonaqueous capillary electrophoresis (NACE) combined with laser-induced fluorescence (LIF) detection was developed and compared with classic aqueous modes of electrophoresis in terms of resolution of solutes of interest and sensitivity of the fluorescence detection. Catecholamines derivatized with 4-chloro-7-nitro-2,1,3-benzoxadiazole (NBD-Cl) were chosen as test analytes for their subtle fluorescence properties. In aqueous systems, capillary zone electrophoresis (CZE) was not suitable for the analysis of test analytes due to complete fluorescence quenching of NBD-labeled catecholamines in neat aqueous buffer. The addition of micelles or microemulsion droplets into aqueous running buffer can dramatically improve the fluorescence response, and the enhancement seems to be comparable for micellar electrokinetic chromatography (MEKC) and microemulsion electrokinetic chromatography (MEEKC). As another alternative, NACE separation was advantageous when performing the analysis under the optimum separation condition of 20 mM sodium tetraborate, 20 mM sodium dodecyl sulfate (SDS), 0.1% (v/v) glacial acetic acid, 20% (v/v) acetonitrile (ACN) in methanol medium after derivatization in ACN/dimethyl sulfoxide (DMSO) (3:2, v/v) mixed aprotic solvents containing 20 mM ammonium acetate. Compared with derivatization and separation in aqueous media, NACE-LIF procedure was proved to be superior, providing high sensitivity and short migration time. Under respective optimum conditions, the NACE procedure offered the best fluorescence response with 5-24 folds enhancement for catecholamines compared to aqueous procedures. In addition, the mechanisms of derivatization and separation in nonaqueous media were elucidated in detail.     

Simultaneous determination of silicon and phosphorus in soil and plants by reversed-phase ion-pair chromatography

A reversed-phase ion-pair high-performance liquid chromatographic method, using tetrabutylammonium bromide (TBABr) as ion-pair reagent, has been developed for the simultaneous analysis of silicon (Si) and phosphorus (P) as heteropoly acids in soil and plant samples. The effect of the concentrations of ion-pair reagent, acetate buffer and organic modifier as well as the pH of buffer on separation was made clear. The reaction conditions and stability of heteropoly acids were investigated. Furthermore, the phenomenon occurred in the optimized process was also further researched. The separation was performed on a reversed-phase C(18) column within 11 min with 40:60 (v/v) 0.1M acetate buffer (pH 3.9)-acetonitrile (ACN) containing 0.8 mM TBABr as a mobile phase. The linear ranges of the peak area calibration curves for Si and P were 0.08-50 mg/L and 0.40-50 mg/L, respectively. The detection limits calculated at S/N=3 were 0.0057 mg/L and 0.0280 mg/L for Si and P, respectively. The method was successfully applied to the analysis of soluble and total contents of Si and P in soil and plant samples.     

Quantitation and characterization of phospholipids in pharmaceutical formulations by liquid chromatography-mass spectrometry

A simple and fast method for phospholipid analysis was developed using high-performance liquid chromatography-mass spectrometry with an atmospheric pressure ionization interface. Separation of the phospholipid molecular species was achieved using a linear gradient of a mixture of chloroform-10 mM ammonium acetate-methanol (30:5:65) on a silica column. Optimization of the mass spectrometer conditions has allowed the method to separate and detect the phospholipids mainly as protonated molecular species. In comparison to existing LC-MS methods, improvement in the total analysis time and sensitivity were achieved. Separation of all major phospholipid molecular classes was achieved in less than 6 min. Marked improvement was observed in the linearity of the response of the phospholipids studied providing a linear response over three orders of magnitude. Data supporting the validation of this method for the characterization of major phospholipids molecular species are also presented.     

Semipermanent capillary coatings in mixed organic-water solvents for CE

This report describes the creation of semipermanent capillary coatings that are compatible with organic-water solvent systems in CE. The coatings are created by simply rinsing the fused-silica capillary with long double-chain cationic surfactants, such as dimethyl-ditetradecyl ammonium bromide (2C(14)DAB), dihexadecyldimethyl ammonium bromide (2C(16)DAB), and dimethyldioctadecyl ammonium bromide (2C(18)DAB). These surfactants generate semipermanent bilayer coatings on the capillary surface, which display a high degree of stability in buffers containing up to 60% v/v of organic solvents, such as methanol and ACN. The coating stability increases with increasing hydrophobicity of the surfactant, i.e., with increasing chain length. For instance, the EOF changes by only 1.2% in a 2C(18)DAB-coated capillary after 130 capillary volumes of rinsing with 60% v/v methanol containing buffer. The bilayer coatings allow separations to be performed without the need to regenerate the coating between runs or to maintain the EOF modifier in the run buffer. Rapid separations (<2 min) of anions and basic drugs with migration time reproducibility of less than 0.5% RSD and efficiencies of 0.4-0.6 million plates/m are obtained. In addition, selectivity changes for small anions and cationic drugs are also observed when the organic solvent content is adjusted.     

Electrokinetic chromatography of twelve monomethylbenz[a]anthracene isomers using a polymerized anionic surfactant

A method for the separation of twelve monomethyl-substituted benz[a]anthracene isomers using poly-(sodium undecylenic sulfate) (poly-SUS) surfactant by means of electrokinetic capillary chromatography (EKC) is described. Several parameters such as concentration of acetonitrile (ACN), pH, as well as applied voltage were studied to optimize the EKC separation. ACN at a concentration of 35% v/v, 12.5 mM phosphate-borate buffer, 30 kV with 0.5% w/v poly-SUS at a pH of 9.5 provided a resolution of a mixture of nine out of twelve methylbenz[a]anthracene (MBA) isomers in 50 min. The results of this study suggest that molecular length of MBA rather than length-to-breath ratio plays an important role in the elution order of some isomers.     

Rapid determination of sterols in vegetable oils by CEC using methacrylate ester‐based monolithic columns

A method for the determination of sterols in vegetable oils by CEC with UV–Vis detection, using methacrylate ester‐based monolithic columns, has been developed. To prepare the columns, polymerization mixtures containing monomers of different hydrophobicities were tried. The influence of composition of polymerization mixture was optimized in terms of porogenic solvent, monomers/porogens and monomer/crosslinker ratios. The composition of the mobile phase was also studied. The optimum monolith was obtained with lauryl methacrylate monomer at 60:40% (wt:wt) lauryl methacrylate/ethylene dimethacrylate ratio and 60 wt% porogens with 20 wt% of 1,4‐butanediol (12 wt% 1,4‐butanediol in the polymerization mixture). Excellent resolution between sterols was achieved in less than 7 min with an 85:10:5 v/v/v ACN–2‐propanol–water buffer containing 5 mM Tris at pH 8.0. The limits of detection were lower than 0.04 mM, and inter‐day and column‐to‐column reproducibilities at 0.75 mM were better than 6.2%. The method was applied to the determination of sterols in vegetable oils with different botanical origins and to detect olive oil adulteration with sunflower and soybean oils.     

Nonaqueous affinity capillary electrophoresis investigation of small molecule molecular recognition

The conditional binding constants for a bis-guanidinium-like receptor and a series of dicarboxylate ligands have been determined in two buffer/solvent systems, namely 25 mM ammonium acetate/1% acetic acid in acetonitrile/methanol (7:3 v:v) and 30 mM N-methyl morpholine/15 mM methanesulfonic acid in acetonitrile/methanol (9:1 v:v). The latter buffer has not been applied before in capillary electrophoresis. The binding constants in both solvent systems decrease as the dicarboxylate length increases. The binding constants are larger in the less competitive N-methyl morpholine buffer. The dicarboxylates associate only weakly with a dicationic analog of the receptor, p-xylyl trimethylammonium, which is not a hydrogen bond donor.     

Separation and determination of phospholipids in plant seeds by nonaqueous capillary electrophoresis

A method has been developed for the separation and determination of phospholipids by nonaqueous capillary electrophoresis in a separation medium of acetonitrile-2-proponol (3:2, v/v), 0.3% acetic acid and 60 mM ammonium acetate. To optimize the separation conditions, the composition of separation medium including alcohols, acetic acid, n-hexane and ammonium acetate was studied. The solvation interaction and ion-dipole interaction were also investigated. The contents of phospholipids in soybean, sunflower, peanut, apricot kernel, filbert and walnut were determined by the recommended method. The results obtained by the nonaqueous capillary electrophoreses were in good agreement with those determined by micellar electrokinetic chromatography.     

Two-dimensional analysis of phospholipids by capillary liquid chromatography/electrospray ionization mass spectrometry

A phospholipid mixture extracted from cultured cells was directly analyzed by capillary (Cap) liquid chromatography (LC)/electrospray ionization (ESI) mass spectrometry (MS). Using a quadrupole mass spectrometer, we analyzed positive molecular ions, negative molecular ions, positive fragment ions and negative fragment ions under four different functions. In the analysis of the elution patterns of the phospholipids, a two-dimensional map, in which the first dimension is elution time and the second dimension is mass, proved useful. Consequently, four different maps can be obtained by each of four different functions. Among them, from negative fragment ions at high cone voltage in the negative ion mode, ions that originated from acyl fatty acid and phosphorylcholine, phosphorylethanolamine and cyclic inositol phosphate can be detected at specific elution times. The map from positive fragment ions at high cone voltage in the positive ion mode indicated ions such as diradylglycerol and derivatives of 1-alkyl or 1-alkenyl cyclic phosphatidic acid from phosphatidylethanolamine (PE), and phosphorylcholine from choline-containing phospholipids. The map produced from positive molecular ions indicated choline-containing phospholipids such as phosphatidylcholine, sphingomyelin, lysophosphatidylcholine and PE. The map of negative molecular ions effectively indicated acidic phospholipids such as phosphatidylinositol. We were able to obtain more than 500 molecular species of phospholipids by this method within a few hours immediately after extraction from culture cells using a mixture of chloroform and methanol (2:1). In this context, we concluded that the combination of Cap-LC and ESIMS seems to be very effective in the analysis of phospholipid classes and their molecular species.     

Chiral separation of cathinone derivatives used as recreational drugs by cyclodextrin-modified capillary electrophoresis

In recent years, cathinone derivatives have entered the global drug market and caused serious social problems in many European countries. Modification of the basic structure of cathinone leads to a multitude of derivatives, including the most popular representative mephedrone. All those substances contain a stereogenic center and therefore two isoforms exist. As it is the case with many chiral active pharmaceutical ingredients, even the pharmacological effect of the enantiomers of those psychoactive compounds may differ. During this research, an easy-to-prepare chiral capillary zone electrophoresis method for the enantioseparation of a set of 19 cathinone derivatives was developed. Testing different types of cyclodextrin (CD), including native-β-CD, carboxymethyl-β-CD, 2-hydroxypropyl-β-CD, sulfated-β-CD, and native γ-CD, best results were obtained with the negatively charged sulfated-β-CD. The effect of the CD concentration, the temperature, and the addition of ACN to the BGE on the enantioseparation is shown by three model compounds. Under optimal conditions, using 20 mg/mL sulfated-β-CD in 50 mM ammonium acetate buffer pH?= 4.5 containing 10% v/v ACN at a cassette temperature of 40°C and with an applied voltage of 20 kV, all derivatives except methedrone were resolved in their enantiomers within 20 min.     

Capillary electrophoretic determination of main components of natural dyes with MS detection

CE with UV-Vis and MS detections was investigated as a technique for detection of main components of selected natural dyes of plant and insect origin. The BGE giving the best separation of the investigated flavonoids and anthraquinoids, suitable for MS detection consisted of 40 mM ammonium acetate solution of pH 9.5 with 40% ACN. LODs obtained with MS detection were even one order of magnitude lower than the ones obtained with UV-Vis detection. Application of MS detection enabled determination of eleven dye compounds from three different chemical groups in 15 min. and proved to be more satisfactory than diode-array detection in the electrophoretic analysis of main classes of natural dyes both in terms of selectivity and sensitivity of analysis.     

Analysis of active alkaloids in the Menispermaceae family by nonaqueous capillary electrophoresis‐ion trap mass spectrometry

A nonaqueous CE‐IT MS with a nanospray ionization interface method was developed for the identification and quantification of tetrandrine (TET), fangchinoline (FAN), and sinomenine (SIN) using berberine as internal standard. The TET, FAN, and SIN standard solutions were directly infused into IT‐MS for collecting MS^1–3 spectra. The major fragment ions of analytes were confirmed and possible main cleavage pathways of fragment ions were studied. A bare fused‐silica capillary was used for separation of the analytes. A sheath liquid (50% aqueous methanol containing 0.2% acetic acid) to the capillary effluent with a nanoelectrospray ionization interface was added. Separation buffer comprised 80 mM solution of ammonium acetate, in a mixture of 70% methanol, 20% ACN, and 10% water, which also contained 1% acetic acid. The CE‐MS method was validated for linearity, sensitivity, accuracy, and precision, and then used to determine the content of the above components. The detection limits of TET, FAN, and SIN are 0.05, 0.08, and 0.15μg/mL, respectively. The precision was no more than 4.67% and the mean recovery of the analytes were 95.36–99.24%. This method was successfully applied to determine TET, FAN, and SIN in real samples radix Stephaniae tetrandrae and rhizomes of Menispermum dauricum.     

Separation of phospholipid classes by hydrophilic interaction chromatography detected by electrospray ionization mass spectrometry

A new isocratic separation method was developed for separation of phospholipid (PL) classes based on a silica hydrophilic interaction liquid chromatography (HILIC) column with electrospray ionization (ESI) mass spectrometric detection. Although HILIC is typically used for polar compounds, also amphiphilic molecules like phospholipids can be separated very well. Compared to normal-phase (NP) chromatography, which is usually used for PL class separation, HILIC has the advantage to use on-line ESI-MS detection because its eluents are ESI compatible. Furthermore, this HILIC method is isocratic and hence less time consuming than most (gradient) NP HPLC methods. A chromatographic baseline separation of a standard mixture containing phosphatidylglycerol (PG), phosphatidylethanolamine (PE), phosphatidylcholine (PC), sphingomyelin (SM) and lysophosphatidylcholine (LPC) was achieved within a total run time of 17 min using a mobile phase consisting of acetonitrile, methanol and ammonium acetate 10 mM. The new method was subsequently tested on phospholipid fractions of a body fluid (human blood plasma) and a tissue extract (swine brain) whereby it achieved nearly the same baseline separation of the PL classes. The detected classes in both cases were PE, PC, SM and LPC.     

Acrylate ester-based monolithic columns for capillary electrochromatography separation of triacylglycerols in vegetable oils

A simple and reliable method for the evaluation of triacylglycerols (TAGs) in vegetable oils by capillary electrochromatography (CEC) with UV-Vis detection, using octadecyl acrylate (ODA) ester-based monolithic columns, has been developed. The percentages of the porogenic solvents in the polymerization mixture, and the mobile phase composition, were optimized. The optimum monolith was obtained at the following ratios: 40:60% (wt/wt) monomers/porogens, 60:40% (wt/wt) ODA/1,3-butanediol diacrylate and 23:77% (wt/wt) 1,4-butanediol/1-propanol (14 wt% 1,4-butanediol in the polymerization mixture). A satisfactory resolution between TAGs was achieved in less than 12 min with a 65:35 (v/v) acetonitrile/2-propanol mixture containing 5 mM ammonium acetate. The method was applied to the analysis of TAGs of vegetable oil samples. Using linear discriminant analysis of the CEC TAG profiles, the vegetable oils belonging to six different botanical origins (corn, extra virgin olive, hazelnut, peanut, soybean and sunflower) were correctly classified with an excellent resolution among all the categories.