离子液体[BMIM]Cl预处理对微晶纤维素酶解的影响

以微晶纤维素为研究对象, 设计了离子液体1-丁基-3-甲基咪唑氯盐(1-butyl-3-methylimidazolium chloride, [BMIM]Cl)预处理微晶纤维素Avicel的实验方法以实现纤维素的高效酶解糖化. 在[BMIM]Cl中Avicel完全溶解, 经水洗沉淀得到再生纤维素, 回收后的离子液体可重复利用. 预处理后底物酶解的可溶性糖转化率在24 h时高达94.65%, 较之同样条件下未经预处理底物的酶解糖转化率(48.57%)有飞跃性提升. 进一步考察了离子液体预处理对纤维素结构及形态的影响, 结果表明: [BMIM]Cl预处理后Avicel氢键减弱; 结晶度明显下降, 结晶型态由纤维素I型转变为纤维素II型; 由规整的平行排布转变为疏松有孔的无序形貌. 正是离子液体预处理引起的纤维素微观与宏观结构性质的显著改变使得再生后纤维素酶解的可溶性糖转化率大幅提高.     

离子液体预处理生物质提高糖化产率

采用酶解糖化法检测离子液体EmimAc和AmimCl对生物质(甘蔗渣和桉木)的预处理效果,考察了温度、时间和固/液质量比对离子液体预处理效果的影响。结果表明,2种离子液体对2种生物质的最佳预处理温度均为140℃,固液质量比均为1∶15,EmimAc对桉木和甘蔗渣的预处理时间分别是12和4 h,而AmimCl所需的时间分别是14和8 h,EmimAc对桉木和甘蔗渣的预处理效果分别是传统方法的13.931和3.886倍,而AmimCl对这2种生物质分别是传统方法的4.665和2.835倍。可见EmimAc的预处理效果优于AmimCl。     

离子液体预处理生物质提高糖化产率

采用酶解糖化法检测离子液体EmimAc和AmimCl对生物质(甘蔗渣和桉木)的预处理效果,考察了温度、时间和固/液质量比对离子液体预处理效果的影响。 结果表明, 2种离子液体对2种生物质的最佳预处理温度均为140 ℃,固液质量比均为1∶15,EmimAc对桉木和甘蔗渣的预处理时间分别是12和4 h,而AmimCl所需的时间分别是14和8 h,EmimAc对桉木和甘蔗渣的预处理效果分别是传统方法的13.931和3.886倍,而AmimCl对这2种生物质分别是传统方法的4.665和2.835倍。 可见EmimAc的预处理效果优于AmimCl。     

离子液体介质中纤维素酶降解纤维素的研究进展

以不可再生资源为原料和能源进行的传统加工工业正面临着资源日益枯竭的现实,所以对可再生资源的研究势在必行。在各种可再生资源中,纤维素生物质是唯一可再生的碳资源,具有取之不尽用之不竭的物质基础,被普遍认为将会部分替代或补充不可再生资源。但由于纤维素的超分子结构,传统的工艺很难将其降解转化,离子液体作为一种新型的绿色溶剂,不仅能够很好地溶解纤维素,同时也是纤维素酶解反应的良好溶剂。综述了国内外离子液体对纤维素溶解、再生以及降解的近期研究成果,分析了其中存在的问题,提出了离子液体降解纤维素的发展方向。     

超临界二氧化碳偶合超声预处理强化玉米秸秆酶水解(英)

提出了一个木质纤维素生物质预处理的全绿色加工过程.以玉米秸秆和玉米芯为原料,以超临界CO₂和超声偶合法对木质纤维素进行预处理.超临界CO₂预处理条件为:压力15-25 MPa,温度120₁70℃,含水量50%,反应时间0.5₄ h.超声场功率600W,温度80℃,作用时间2-8 h.用纤维素酶水解反应获得的还原糖总量来评价预处理效果.结果表明,单纯超临界CO₂和超临界CO₂偶合超声预处理都能够提高生物质水解反应还原糖产量.对于玉米芯,超临界CO₂预处理（170℃,20 MPa,3 0min）后,还原糖产率为62%（未预处理的为12%）.对于玉米秸秆（170℃,20 MPa,2.5 h）,还原糖产率为46.4%.对于玉米芯,超临界CO₂偶合超声预处理（600 W,80℃下超声处理6 h,然后用170℃,20 MPa超临界CO₂预处理30 min）后,还原糖产率为87%.对于玉米秸秆,超临界CO₂偶合超声预处理（600 W,80℃下超声处理8 h,然后用170℃,20 MPa超临界CO₂预处理1 h）后,还原糖产率为25.5%.与未处理生物质相比,X射线衍射结果表明玉米秸秆和玉米芯在超临界CO₂和超声预处理后其结晶度没有明显变化.扫描电镜分析则发现木质纤维素的表面积显著增加.     

微波法合成离子液体[AMIM]Cl及其对纤维素的预处理

利用微波法合成了离子液体1-烯丙基,3-甲基咪唑氯盐[AMIM]Cl,并利用合成的离子液体分别对微晶纤维素、麦草秸杆和玉米芯进行预处理,得到了再生纤维素。考察了纤维素在离子液体中的溶解过程,并通过FT-IR、SEM和酶解对其预处理效果进行了表征。结果表明:微波法可以大大减少反应时间,合成的离子液体[AMIM]Cl可以有效降低纤维素的结晶度,增加其表面粗糙度,提高纤维素酶的可及性及底物的利用率。     

离子液体预处理的纤维素酶解糖化

利用离子液体氯化1-丁基-3-甲基-咪唑([C4mim]Cl)对纤维素进行预处理.结果表明,纤维素经离子液体预处理后聚合度下降,糖化速度随预处理温度增加呈现先增大后下降的趋势,在90℃出现最大值11 77 g/(L·h). 延长预处理时间和采用乙醇作为沉淀剂,可促进酶解糖化,糖化速度比未处理的纤维素提高70%. 根据扫描电子显微镜(SEM)观察,纤维素出现了明显的解聚.     

共溶剂存在下N-烯丙基吡啶氯盐离子液体对纤维素的溶解性能研究

采用一步法合成N-烯丙基吡啶氯盐离子液体([APy]Cl),考察其对纤维素的溶解性能.结果发现,在120℃下对棉浆粕(聚合度(DP)=556)的溶解度可高达19.71%,但再生后聚合度为223,热降解严重.通过添加不同种类共溶剂的方法克服此缺点.结果表明,有机溶液(DMSO,DMAc,DMF或吡啶)作为[APy]Cl的共溶剂时,[APy]Cl/DMAc复合溶剂对棉浆粕的溶解效果最佳,100℃下溶解度为15.03%,再生后聚合度为403.此外降低了溶剂成本.但70℃下,溶解度仅为1.36%,溶解能力较弱.继续探讨了[AMIM]Cl作为[APy]Cl的共溶剂时对纤维素的溶解性能,结果表明,70℃下,[APy]Cl/[AMIM]Cl复合溶剂对棉浆粕的溶解度为8.78%,再生后聚合度为516.可知添加上述2种共溶剂均使[APy]Cl在低于自身熔点下形成液体并能够溶解一定量纤维素,拓宽了溶解温度区间及应用平台.对FTIR,XRD和TGA谱图分析,结果表明上述为纤维素的直接溶剂,可将其晶型由Ⅰ型转变成Ⅱ型,再生后热稳定性稍有降低.通过照片和SEM表明再生膜无色透明,结构致密.     

纤维素在离子液体[AMMor]Cl/[AMIM]Cl混合溶剂中的溶解性能

研究了纤维素在混配离子液体N-甲基-N-烯丙基吗啉氯盐[AMMor]Cl/3-甲基-1-烯丙基咪唑氯盐[AMIM]Cl中的溶解性能, 结果表明, [AMMor]Cl/[AMIM]Cl混配溶剂能有效溶解天然纤维素, 且在相同条件下, 溶解能力要优于离子液体[AMIM]Cl; 随着溶解温度的升高, 溶解时间大大缩短. 利用FTIR, XRD和TGA方法分析了再生纤维素的化学结构和热稳定性, 结果表明, 未经活化的纤维素可直接溶于[AMMor]Cl/[AMIM]Cl而不发生其它衍生化反应, 且天然纤维素在该溶剂体系中纤维素聚合度下降较小.     

不同方法预处理的玉米秸秆结构与酶解分析

在利用秸秆进行工业转化时,因为秸秆结构复杂,导致转化效率低,所以需对秸秆进行预处理,破坏秸秆复杂结构,提高转化效率。采用扫描电镜(SEM)、傅里叶变换红外光谱(FT-IR)和X射线衍射技术分析不同预处理方式对玉米秸秆微观结构的影响,并利用纤维素酶对不同预处理秸秆进行酶解,评价预处理效果。扫描电镜结果表明,不同预处理方式对秸秆表面形态和秸秆整体结构造成不同程度的破坏,其中NaOH预处理后的秸秆表面结构坍塌明显,表明木质纤维素结构被有效打破。利用傅里叶变换红外光谱对不同预处理方式的秸秆进行分析,其中1600和1510cm~(-1)为木质素的特征峰,NaOH预处理后的秸秆在此处的特征峰基本消失,表明NaOH预处理对秸秆木质素的去除效率比较明显。1744~1734 cm~(-1)为C=O伸缩振动特征峰,此峰的强度与木质素和半纤维素的含量有关,采用不同方法预处理后,此峰的吸收强度不同程度地减少,表明各种预处理方法不同程度地去除了秸秆的木质素和半纤维素。X-射线衍射分析表明,不同预处理后秸秆的结晶度均发生不同程度的改变,其中H_2SO_4预处理后秸秆的结晶度提高最大,达到43.4%。其中NaOH预处理秸秆后,用纤维素酶酶解60h,使其酶解产糖量达到33.32g/L。本研究分析了不同秸秆预处理方法的效果,为利用玉米秸秆生产生物化工产品提供了理论依据。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.