梳状聚合物研究进展

梳状聚合物是一类具有高接枝密度的接枝型共聚物。由于高密度接枝的侧链之间相互排斥,导致梳状聚合物主链被迫伸直,整个梳状聚合物表现出棒状构象。同时,相比于一般线形聚合物而言,梳状聚合物分子量较容易达到很高,形成几十到上百纳米尺寸的结构,因此有着广泛的应用前景。目前,人们对于梳状聚合物的研究集中于其合成、结构以及性能等领域,其中主要基于对柔性侧链、柔性主链梳状聚合物的研究。本文对于梳状聚合物的合成、刚性主链和刚性侧链梳状聚合物发展现状以及梳状聚合物的性质和应用进行了总结。     

机理转移法合成星形梳状聚丁二烯-g-聚甲基丙烯酸甲酯共聚物的研究

结合活性负离子聚合与原子转移自由基聚合(ATRP),采用机理转移法制备了一系列窄分布且分子量可控的星形梳状聚丁二烯-g-聚甲基丙烯酸甲酯接枝共聚物(SC-(PB-g-PMMA)).首先通过阴离子聚合,制备星形聚丁二烯,后经甲酸-过氧化氢原位环氧化对链中部分双键进行环氧化,再与原位生成2-溴异丁酸发生酯化反应,得到具有链中活性溴的星形大分子引发剂(SPB-Brn).然后,利用该大分子引发剂,采用CuCl/CuCl2/PMDETA催化体系,通过ATRP聚合单体MMA,合成出星形梳状SC-(PB-g-PMMA)聚合物.通过GPC,1H-NMR和FTIR等分析手段对合成的星形大分子引发剂及星形梳状聚合物进结构表征,证实得到目标产物,并同时研究了聚合物的热力学性质与溶液性质.     

梳状P(MMA-co-MAh)-g-PEGME共聚物的合成及结构与性能

用自制的甲基丙烯酸甲酯和马来酸酐的共聚物P(MMA-co-MAh)为反应物,聚乙二醇单甲醚(PEGME)为接枝单体,合成了梳状P(MMA-co-MAh)共聚物多缩乙二醇酯(P(MMA-co-MAh)-g-MPEG).采用傅立叶红外光谱(FTIR)、核磁共振(NMR)13C谱、1H谱以及H,C-COSP谱对所合成的梳状共聚物结构进行表征;热失重分析(TGA)和示差扫描量热法(DSC)对所合成的共聚物的物理性能进行了分析.FTIR及NMR结果表明,聚乙二醇单甲醚通过酯化反应接枝到P(MMA-co-MAh)共聚物上,形成以MMA/MAh共聚物为主链,聚乙二醇单甲醚为侧链的梳状共聚物,其在马来酸酐上的接枝率大约为20%;热性能分析结果表明,合成的梳状共聚物热分解温度与共聚物P(MMA-co-MAh)的分解温度相差不大,接枝后的梳状共聚物也具有高的热稳定性,起始热分解温度在325.9℃左右,且该梳状共聚物具有两个玻璃化转变温度,一个是由于侧链的玻璃化转变引起的,温度为32℃左右;一个是主链的玻璃化转变引起的,温度为120℃左右.在主链玻璃化转变温度以下,侧链是可以移动的,有利于电活性物质和离子等在聚合物基体中的扩散和迁移.     

含mPEG侧链的水溶性梳状聚合物的合成及其侧链受限结晶行为研究

采用大单体与小单体共聚的技术,通过自由基引发溶液聚合,合成了一系列水溶性梳状聚合物———聚丙烯酸接枝聚乙二醇单甲醚(PAA-g-mPEG).制备过程分两步进行,首先合成大单体聚乙二醇单甲醚丙烯酸酯,然后将大单体与丙烯酸单体共聚,合成了梳状聚合物.通过控制反应条件,获得了一系列主链和支链组成比不同的接枝共聚物.用傅立叶变换红外光谱(FT-IR)和核磁共振氢谱(1H-NMR)表征了共聚物的结构,并对其侧链的结晶行为进行了研究.采用差热扫描量热法(DSC)表征并分析了不同侧链长度的mPEG的热性能及其结晶情况.利用相差显微镜和原子力显微镜(AFM)观察薄膜的结晶形貌,表明梳状聚合物的侧链mPEG在受限条件下的薄膜结晶形貌为高度支化的晶体,初步分析了mPEG链长及其在共聚物中的重量百分含量对晶体形貌的影响.     

结构明确的梳形支化聚合物的合成与表征

通过活性聚苯乙烯(PS)和聚异戊二烯(PI)负离子与含1,1-二苯基乙烯(DPE)侧基的聚苯乙烯(PSe)的偶联反应合成了结构明确的每个重复单元含一条侧链的梳形支化聚合物,其中,PSe是通过Sc单体的原子转移自由基聚合(ATRP)和Wittig反应制得的.用IR1、H-NMR、GPC和SLS等测试方法对所得梳形支化聚合物进行了详细表征,讨论了活性负离子链与PSe的DPE基团的配比对接枝率的影响.结果表明,活性负离子链与DPE基团的偶联反应是高效的,可以通过调节活性负离子链与DPE基团的加料比来控制接枝率.另外,还讨论了PSe和活性负离子链的分子量对接枝率的影响.结果表明,在实验范围内当活性负离子链过量时可获得几乎定量的接枝率.     

亲水梳状环氧聚合物载体柔性固定化脂肪酶

以氯乙酰化聚苯乙烯微球载体为大分子引发剂,以甲基丙烯酸缩水甘油酯和亲水性丙烯酰胺为共聚接枝单体,以氯化亚铜及2,2'-联吡啶为催化体系,采用原子转移自由基聚合法接枝合成了具有柔性链的亲水梳状环氧聚合物载体PS-acyl-P(AM-co-GMA),并将其用于耐有机溶剂YCJ01脂肪酶的共价柔性固定化.结果表明,固定化酶催...     

原子转移自由基聚合技术制备L-苯丙氨酸手性配体交换色谱固定相及其对手性化合物的拆分

在室温条件下,以甲基丙烯酸环氧丙酯(GMA)为单体,溴异丁酰溴为引发剂,CuCl/2,2′-联吡啶(Bpy)为催化剂,通过原子转移自由基聚合(ATRP)反应,将甲基丙烯酸环氧丙酯聚合在硅胶表面。然后再将L-苯丙氨酸共价键合在硅胶表面的聚合物上,制备了新型手性配体交换色谱固定相,并用该固定相对DL-氨基酸进行分离。用元素分析对其进行了表征;详细考察了固定相的合成过程以及流动相pH值、流动相铜离子浓度、柱温等色谱条件对DL-氨基酸对映体拆分的影响。元素分析得出该固定相表面L-苯丙氨酸接枝密度达到4.32 mg/m2;在手性配体交换分离模式下,流动相为0.05 mol/L KH2PO4-0.1 mmol/L Cu(Ac)2水溶液、流速为1.0 mL/min、柱温为50 ℃和检测波长为223 nm条件下,该色谱固定相可以分离DL-天冬氨酸、DL-天冬酰胺等。同时,流动相pH值、铜离子浓度以及柱温对手性对映体的拆分有较大影响。与传统的在硅胶表面直接键合L-苯丙氨酸制得的固定相相比,所合成的固定相接枝密度高,分离效果好,对DL-天冬氨酸及DL-天冬酰胺实现了基线分离。结果表明,在手性配体交换分离模式下,固定相具有良好的拆分性能。     

活性自由基聚合(Iniferter)法制备聚合物包覆硅胶固定相及其色谱性能评价

应用活性自由基聚合法, 在接枝iniferter的硅球表面键合甲基丙烯酸异辛酯-co-乙二醇二甲基丙烯酸酯聚合层, 制备了聚合物包覆硅胶色谱固定相, 并研究了合成条件对于聚合层及分离效果的影响. 在一定聚合时间中, 接枝聚合物质量与反应时间呈线性关系, 并可以在得到聚合物包覆硅胶的基础上, 利用包覆硅胶中的iniferter再次引发接枝聚合, 体现了活性自由基聚合的特点. 聚合物包覆硅胶对于烷基苯同系物、碱性化合物及羟基苯甲酸酯具有很好的色谱分离能力及柱效, 同时, 由于聚合层能够有效地覆盖硅球表面的硅羟基, 减小了碱性化合物的拖尾. 研究工作提供了新的聚合物包覆硅胶固定相的合成方法.     

基于酒石酸衍生物的聚合物型手性固定相的制备及手性识别

以D-(-)-酒石酸和D-(-)-酒石酸二异丙基酯为手性源,合成了D-(-)-酒石酸二苄酯和D-(-)-酒石酸二苄胺,这2种单体再分别与对苯二甲酰氯和对苯二异氰酸酯进行聚合,得到聚酯和聚氨酯型手性选择体.将这2种聚合物同时键合到氨丙基硅胶上制得双选择体手性固定相.为了比较分离性能,将两种聚合物分别单独地键合在氨丙基硅胶上,制备了2种单选择体手性固定相.用FTIR、元素分析和NMR对所合成的化合物进行了表征.在相同色谱条件下,用31种手性化合物对3种固定相的手性识别能力进行了评价.研究结果表明,3种固定相均具有较好的手性识别能力,双选择体固定相手性识别能力优于单选择体手性固定相,双选择体手性固定相中的2个选择体之间存在协同作用.     

原位聚合那格列奈分子印迹手性固定相的分子识别特性研究

以手性药物那格列奈为模板分子,采用原位聚合法制备了具有特定识别性能和手性拆分能力的分子印迹聚合物,并用作高效液相色谱固定相实现了那格列奈与其对映体的手性拆分．通过静态结合方法考察了该聚合物的选择结合能力,并讨论了手性分离过程中的热力学性质．结果表明,原位聚合法制备的棒状聚合物固定相对模板分子及其对映体有很好的手性拆分性能．     

Gels from a semifluorinated n-alkane in fluorinated solvents as a probe for intermolecular interactions

Diblock semifluorinated n-alkanes can form aggregates and gels in fluorinated solvents. We have investigated the thermal behavior of binary mixtures comprising F(CF₂)₈(CH₂)₁₆H and fluorinated solvents. The solvents were perfluorohexane, perfluoroheptane, perfluorooctane, perfluorooctyl bromide, perfluorodecalin, and perfluorotributylamine. The phase diagrams were used to calculate the activity coefficients of the two components and the main excess thermodynamic functions. The solubility and self-assembly behavior of F₈H₁₆ in the fluorinated solvents are related to the different solute–solvent dispersion interactions that depend on the polarizabilities and ionization potentials of the interacting species, and on the structural properties of the solvent.     

Studies on the Formation of Catalytically Active PGM Nanoparticles from Model Solutions as a Basis for the Recycling of Spent Catalysts

The paper presents basic studies on the precipitation of platinum, palladium, rhodium, and ruthenium nanoparticles from model acidic solutions using sodium borohydride, ascorbic acid, and sodium formate as reducing agents and polyvinylpyrrolidone as a stabilizing agent. The size of the obtained PGM particles after precipitation with NaBH₄ solution does not exceed 55 nm. NaBH₄ is an efficient reducer; the precipitation yields for Pt, Pd, Ru, Rh are 75, 90, 65 and 85%, respectively. By precipitation with ascorbic acid, it is possible to efficiently separate Pt, Rh, and Ru from Pd from the two-component mixtures. The obtained Pt, Pd, and Rh precipitates have the catalytic ability of the catalytic reaction of p-nitrophenol to p-aminophenol. The morphological characteristic of the PGM precipitates was analyzed by AFM, SEM-EDS, and TEM.     

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性;均苯四甲酸二酐;联苯四羧酸二酐;二羟基联苯胺;聚酰亚胺;聚苯并噁唑;耐热性     

HCOO在Cu(110)、Ag(110)和Au(110)表面的吸附

采用密度泛函理论(DFT)以及广义梯度近似方法(GGA)计算了甲酸根(HCOO)在Cu(110)、Ag(110)和Au(110)表面的吸附. 计算结果表明, 短桥位是最稳定的吸附位置, 计算的几何参数与以前的实验和计算结果吻合. 吸附热顺序为Cu(110)(-116 kJ·mol-1)>Ag(110)(-57 kJ·mol-1)>Au(110)(-27 kJ·mol-1), 与实验上甲酸根的分解温度相一致. 电子态密度分析表明, 吸附热顺序可以用吸附分子与金属d-带之间的Pauli 排斥来关联, 即排斥作用越大, 吸附越弱. 另外还从计算的吸附热数据以及实验上HCOO的分解温度估算了反应CO2+1/2H2→HCOO的活化能, 其大小顺序为Au(110)>Ag(110)>Cu(110).     

Direct Quantitation of Phytocannabinoids by One-Dimensional 1H qNMR and Two-Dimensional 1H-1H COSY qNMR in Complex Natural Mixtures

The widespread use of phytocannabinoids or cannabis extracts as ingredients in numerous types of products, in combination with the legal restrictions on THC content, has created a need for the development of new, rapid, and universal analytical methods for their quantitation that ideally could be applied without separation and standards. Based on previously described qNMR studies, we developed an expanded ¹H qNMR method and a novel 2D-COSY qNMR method for the rapid quantitation of ten major phytocannabinoids in cannabis plant extracts and cannabis-based products. The ¹H qNMR method was successfully developed for the quantitation of cannabidiol (CBD), cannabidiolic acid (CBDA), cannabinol (CBN), cannabichromene (CBC), cannabichromenic acid (CBCA), cannabigerol (CBG), cannabigerolic acid (CBGA), Δ9-tetrahydrocannabinol (Δ9-THC), Δ9-tetrahydrocannabinolic acid (Δ9-THCA), Δ8-tetrahydrocannabinol (Δ8-THC), cannabielsoin (CBE), and cannabidivarin (CBDV). Moreover, cannabidivarinic acid (CBDVA) and Δ9-tetrahydrocannabivarinic acid (Δ9-THCVA) can be distinguished from CBDA and Δ9-THCA respectively, while cannabigerovarin (CBGV) and Δ8-tetrahydrocannabivarin (Δ8-THCV) present the same ¹H-spectra as CBG and Δ8-THC, respectively. The COSY qNMR method was applied for the quantitation of CBD, CBDA, CBN, CBG/CBGA, and THC/THCA. The two methods were applied for the analysis of hemp plants; cannabis extracts; edible cannabis medium-chain triglycerides (MCT); and hemp seed oils and cosmetic products with cannabinoids. The ¹H-NMR method does not require the use of reference compounds, and it requires only a short time for analysis. However, complex extracts in ¹H-NMR may have a lot of signals, and quantitation with this method is often hampered by peak overlap, with 2D NMR providing a solution to this obstacle. The most important advantage of the COSY NMR quantitation method was the determination of the legality of cannabis plants, extracts, and edible oils based on their THC/THCA content, particularly in the cases of some samples for which the determination of THC/THCA content by ¹H qNMR was not feasible.     

Transition metal complexes of the tripodal ligand 4-(2′-pyridylmethyl)-4-azaheptane-1,7-diamine. Crystal structures of [CuLCl]ClO4 and [NiL(MeCN)2](ClO4)2

The tripodal ligand 4-(2′-pyridylmthyl)-4-azaheptane-1,7-diamine has been prepared by reaction of 2-aminemethyl pyridine with acrylonitrile, followed by the reduction of the nitrile groups. Copper(II), nickel(II), zinc(II), cobalt(III) and chromium(III) complexes of the ligand have been prepared and characterized and the crystal structures of the complexes [CuLCl]ClO₄ and [NiL(MeCN)₂](ClO₄)₂ determined. The copper complex is five coordinate with approximate square pyramidal stereochemistry with the apical position occupied by a primary amine donor. The nickel complex is octahedral with the pyridine nitrogen donor lying trans to an acetonitrile ligand.     

SYNTHESIS AND CHARACTERIZATION OF METAL COMPLEXES WITH AMPICILLIN

Abstract

The reaction, in water, of Co(II), Ni(II), Cu(II), Zn(II) and Cd(II) ions with sodium ampicillinate at room temperature has allowed isolation of dimers with the following general formula [M(amp)Cl]₂ × nH₂O (n = 1.5?3.2). The complexes were characterized by elemental analyses, conductivity measurements, magnetic susceptibilities and spectroscopic methods (IR, Raman, EPR and UV-Visible). A dinuclear structure based on octahedrally coordinated metal ions is proposed.     

Magnetism of metal-nitroxide compounds involving bis-chelating imidazole and benzimidazole substituted nitronyl nitroxide free radicals

Coordination compounds based on imidazole and benzimidazole substituted nitronyl nitroxide radicals with transition metal ions and trivalent lanthanide ions are described from the perspective of their magnetic properties.For the transition metal compounds the crystal structures show various metal-nitroxide dimensionalities including mononuclear (0D), one-dimensional (1D) and two-dimensional (2D) complexes. The mononuclear complexes were isolated with most metal ions of the first transition series. One copper(II) complex shows a copper(II)-radical ferromagnetic coupling (J = +75 cm⁻¹) while for the other mononuclear compounds, mainly with manganese(II), the metal-radical interactions are antiferromagnetic. The one-dimensional and two-dimensional complexes are manganese(II) compounds which show canting effects leading to weak ferromagnetism.For the trivalent lanthanide ions [La(III), Gd(III) and Eu(III)], three series of mononuclear complexes were obtained in which the metal center is bound to four, two or one nitroxide radicals depending on the counter ions and ancillary ligands. Unexpectedly, in most gadolinium(III) complexes, the Gd(III)-radical interactions were found to be antiferromagnetic in contradiction with other foundings and previous theoretical models. In support to the magnetic studies, the optical properties of the lantanide complexes have also been investigated and are briefly described.     

具有聚集诱导发光性质的近红外荧光染料

聚集诱导发光(AIE)现象的发现为解决传统有机荧光分子在高浓度和聚集形态下存在的荧光猝灭问题提供了最佳方案,并实现了在光电器件、化学传感、生物成像和靶向治疗等众多领域的广泛应用.随着对AIE 发光机理研究的不断深入,AIE 分子体系得到了极大的扩展.其中,一类具有给体-受体结构的AIE分子能够显著降低分子能隙,使发光分...     

Simple,Selective, and Sensitive Spectrophotometric Method for Determination of Trace Amounts of Nickel（Ⅱ）, Copper （Ⅱ）, Cobalt （Ⅱ）, and Iron （Ⅲ） with a Novel Reagent 2-Pyridine Carboxaldehyde Isonicotinyl Hydrazone

A selective and sensitive reagent of 2-pyridine carboxaldehyde isonicotinyl hydrazone（2-PYAINH） was synthesized and studied for the spectrophotometric determination of nickel, copper, cobalt, and iron in detail. At a pH value of 7.0, 9,0, 9.0, and 8.0, respectively, which greatly increased the selectivity; nickel, copper, cobalt, and iron reacted with 2-PYAINH to form a 1：2 yellow-orange, 1：2 yellow-green, 1：2 yellow and 1：1 yellow complexes, with absorption peaks at 363, 352, 346, and 359 nm, respectively. Under the optimal conditions, Beer＇s law was obeyed over the ranges of 0.01-1.4, 0.01-1.5, 0.01-2.7, and 0.01-5.4 mg/L respectively. The apparent molar absorptivity and Sandell＇s sensitivities were 8.4×10^4, 5.2×10^4, 7.1×10^4, and 3.9×10^4 L·mol^-l·cm^-1, respectively, and 0.00069, 0.0012, 0.00078, and 0.0014 μg·cm2, respectively. The detection limits were found to be 0.001, 0.002, 0.003, and 0.01 mg/L, respectively. The detailed study of various interfering ions to make the method more sensitive was carried out and selective and several real samples were analyzed with satisfactory results.