高效液相色谱-串联质谱法同时测定肉类罐头中双酚-二缩水甘油醚

建立了同时测定肉类罐头中双酚A-二缩水甘油醚(BADGE)、双酚F-二缩水甘油醚(BFDGE)及其衍生物双酚A-(2,3-二羟丙基)甘油醚(BADGE•H2O)、双酚A-双(2,3-二羟丙基)醚(BADGE•2H2O)、双酚A-(3-氯-2-羟丙基)(2,3-二羟丙基)醚(BADGE•H2O•HCl)、双酚A-(3-氯-2-羟丙基)甘油醚(BADGE•HCl)、双酚A-双(3-氯-2-羟丙基)醚(BADGE•2HCl)、双酚F-双(2,3-二羟丙基)醚(BFDGE•2H2O)、双酚F-双(3-氯-2-羟丙基)醚(BFDGE•2HCl)9种环境激素的高效液相色谱-串联质谱分析方法。样品经叔丁基甲醚提取,HLB固相萃取小柱净化,C18色谱柱分离,用5 mmol/L醋酸铵溶液(含0.1%甲酸)与甲醇为流动相梯度洗脱,质谱多反应监测(MRM)模式检测,基质标准校正,外标法定量。结果表明,这9种化合物在10.0～2000.0 μg/L范围内线性关系良好;定量限(以信噪比≥10计)为10.0 μg/kg;在高、中、低3个加标水平下9种化合物的平均添加回收率为79.6%～100.9%,相对标准偏差为6.3%～12.1%。该方法具有较高的灵敏度和准确度,能满足法规要求的对肉类罐头中双酚A-二缩水甘油醚、双酚F-二缩水甘油醚及其衍生物残留量的快速检测及准确定量。     

固相萃取-高效液相色谱-串联质谱测定水中8种双酚-二环氧甘油醚

建立了水中8种双酚-二环氧甘油醚（双酚A二缩水甘油醚（BADGE）及其衍生物双酚A（3-氯-2-羟丙基）甘油醚（BADGE·5HCl）、双酚A双（3-氯-2-羟丙基）醚（BADGE·52HCl）、双酚A（2,3-二羟丙基）甘油醚（BADGE·5H₂O）、双酚A双（2,3-二羟丙基）醚（BADGE·52H₂O）、双酚A（3-氯-2-羟丙基）（2,3-二羟丙基）醚（BADGE·5HCl·5H₂O）和双酚F-二环氧甘油醚（BFDGE）及其衍生物双酚F双（3-氯-2-羟丙基）醚（BFDGE·52HCl））的固相萃取-高效液相色谱-串联质谱（SPE-HPLC-MS/MS）测定方法。10个饮用水接触涂料样品在室温避光条件下,以超纯水浸泡（24±1）h,然后取200 mL经C₁₈固相萃取柱进行净化浓缩,以C₁₈色谱柱进行分离,以5 mmol/L醋酸铵、甲醇和水为流动相进行梯度洗脱,质谱多反应监测（MRM）模式检测,外标法定量。结果表明,8种双酚-二环氧甘油醚在0.007~5.00 μg/L线性关系良好,相关系数均大于0.9990,该方法对8种双酚-二环氧甘油醚的定量限为7~91 ng/L,回收率为79.1%~101%,RSD为4.0%~12%。该方法具有灵敏度高、选择性强的特点,能够满足水中双酚-二环氧甘油醚的快速检测和准确定量。     

多壁碳纳米管固相萃取-高效液相色谱-串联质谱法测定食品接触材料中双酚-二环氧甘油醚的迁移量

建立了测定食品接触材料中6种双酚-二环氧甘油醚(双酚A二缩水甘油醚(BADGE)及其衍生物双酚A(2,3-二羟丙基)甘油醚(BADGE•H2O)、双酚A(3-氯-2-羟丙基)甘油醚(BADGE•HCl)、双酚A(3-氯-2-羟丙基)(2,3-二羟丙基)醚(BADGE•H2O•HCl)和双酚F二缩水甘油醚(BFDGE)及其衍生物双酚F双(3-氯-2-羟丙基)甘油醚(BFDGE•2HCl))迁移到食品中的迁移量的高效液相色谱-串联质谱法(HPLC-MS/MS)。样品以叔丁基甲醚(MTBE)为提取溶剂,超声提取,提取液经多壁碳纳米管(MWCNTs)固相萃取(SPE)柱富集、净化。以COSMOSIL C18为分析柱,流动相为0.1%甲酸的5 mmol/L醋酸铵溶液和甲醇。6种双酚-二环氧甘油醚在1.0～100 μg/L范围内线性关系良好(r2＞0.9991)。在3个添加水平下,6种目标化合物的回收率范围为78.6%～89.9%,相对标准偏差小于10%。方法检出限范围为0.5～1.5 μg/L。该方法操作简单,灵敏度高,可应用于食品接触材料中双酚-二环氧甘油醚迁移量的快速检测。     

Simultaneous determination of NOGE-related and BADGE-related compounds in canned food by ultra-performance liquid chromatography–tandem mass spectrometry

An improved analytical method enabling rapid and accurate determination and identification of bisphenol F diglycidyl ether (novolac glycidyl ether 2-ring), novolac glycidyl ether 3-ring, novolac glycidyl ether 4-ring, novolac glycidyl ether 5-ring, novolac glycidyl ether 6-ring, bisphenol A diglycidyl ether, bisphenol A (2,3-dihydroxypropyl) glycidyl ether, bisphenol A (3-chloro-2-hydroxypropyl) glycidyl ether, bisphenol A bis(3-chloro-2-hydroxypropyl) ether, and bisphenol A (3-chloro-2-hydroxypropyl) (2,3-dihydroxypropyl) ether in canned food and their contact packaging materials has been developed by using, for the first time, ultra-performance liquid chromatography coupled with tandem mass spectrometry. After comparison of electrospray ionization and atmospheric pressure chemical ionization in positive and negative-ion modes, tandem mass spectrometry with positive electrospray ionization was chosen to carry out selective multiple reaction monitoring analysis of novolac glycidyl ethers, bisphenol A diglycidyl ether, and its derivatives. The analysis time is only 5.5 min per run. Limits of detection varied from 0.01 to 0.20 ng g(-1) for the different target compounds on the basis of a signal-to-noise ratio (S/N) = 3; limits of quantitation were from 0.03 to 0.66 ng g(-1). The relative standard deviation for repeatability was <8.01%. Analytical recovery ranged from 87.60 to 108.93%. This method was successfully applied to twenty samples of canned food and their contact packaging materials for determination of migration of NOGE, BADGE, and their derivatives from can coatings into food.     

Microwave‐assisted extraction for the simultaneous determination of Novolac glycidyl ethers,bisphenol A diglycidyl ether,and its derivatives in canned food using HPLC with fluorescence detection

A microwave‐assisted extraction (MAE) protocol and an efficient HPLC analysis method were first developed for the fast extraction and simultaneous determination of bisphenol F diglycidyl ether (Novolac glycidyl ether 2‐Ring), Novolac glycidyl ether 3‐Ring, Novolac glycidyl ether 4‐Ring, Novolac glycidyl ether 5‐Ring, Novolac glycidyl ether 6‐Ring, bisphenol A diglycidyl ether, bisphenol A (2,3‐dihydroxypropyl) glycidyl ether, bisphenol A (3‐chloro‐2‐hydroxypropyl) glycidyl ether, bisphenol A bis(3‐chloro‐2‐hydroxypropyl) ether, bisphenol A (3‐chloro‐2‐hydroxypropyl) (2,3‐dihydroxypropyl) ether in canned fish and meat. After being optimized in terms of solvents, microwave power and irradiation time, MAE was selected to carry out the extraction of ten target compounds. Analytes were purified by poly(styrene‐co‐divinylbenzene) SPE columns and determinated by HPLC‐fluorescence detection. LOD varied from 0.79 to 3.77 ng/g for different target compounds based on S/N=3; LOQ were from 2.75 to 10.92 ng/g; the RSD for repeatability were <8.64%. The analytical recoveries ranged from 70.46 to 103.44%. This proposed method was successfully applied to 16 canned fish and meat, and the results acquired were in good accordance with the studies reported. Compared with the conventional liquid–liquid extraction and ultrasonic extraction, the optimized MAE approach gained the higher extraction efficiency (20–50% improved).     

Silver nanoparticles fluorescence enhancement effect for determination of nucleic acids with kaempferol-Al(III)

Nucleic acids can greatly enhance fluorescence intensity of the kaempferol (Km)-Al(III) system in the presence of silver nanoparticles (AgNPs). Based on this, a novel method for the determination of nucleic acids is proposed. Under studied conditions, there are linear relationships between the extent of fluorescence enhancement and the concentration of nucleic acids in the range of 5.0 × 10⁻⁹ to 2.0 × 10⁻⁶ g mL⁻¹ for fish sperm DNA (fsDNA), 7.0 × 10⁻⁹ to 2.0 × 10⁻⁶ g mL⁻¹ for salmon sperm DNA (smDNA) and 2.0 × 10⁻⁸ to 3.0 × 10⁻⁶ g mL⁻¹ for yeast RNA (yRNA), and their detection limits are 2.5 × 10⁻⁹ g mL⁻¹, 3.2 × 10⁻⁹ g mL⁻¹ and 7.3 × 10⁻⁹ g mL⁻¹, respectively. Samples were satisfactorily determined. And the system of Km-Al(III)-AgNPs was used as a fluorescence staining reagent for sensitive DNA detection by DNA pattern of agarose gel electrophoresis analysis. The results indicate that the fluorescence enhancement should be attributed to the formation of Km-Al(III)-AgNPs-nucleic acids aggregations through electrostatic attraction and adsorption bridging action of Al(III) and the surface-enhanced fluorescence effect of AgNPs.     

A novel reusable ionic liquid chemically bonded fused-silica fiber for headspace solid-phase microextraction/gas chromatography-flame ionization detection of methyl tert-butyl ether in a gasoline sample

A novel ionic liquid (IL) bonded fused-sil-ica fiber for headspace solid-phase microextraction (HS-SPME)/gas chromatography-flame ionization detection (GC-FID) of methyl tert-butyl ether (MTBE) in a gasoline sample was prepared and used. The new proposed chemically bonded fiber has better thermal stability and durability than its corresponding physically coated fiber. Another advantage is that no spacer was used for the purpose of bonding the IL to the surface of the fused-silica. The latter advantage makes the preparation of these fibers easier with lower cost than those prepared using sol–gel method. The ionic liquid 1-methyl-3-(3-trimethoxysilyl propyl) imidazolium bis(trifluoromethylsulfonyl) imide was synthesized and cross linked to the surface of the fused-silica fiber. Then, the chemically IL-modified fibers were applied to the headspace extraction of MTBE. The chemically IL-modified fibers showed improved thermal stability at temperatures up to 220 °C relative to the physically IL-modified fibers (180 °C). The chemically bonded IL film on the surface of the fused-silica fiber was durable over 16 headspace extractions without any significant loss of the IL film. The calibration graph was linear in a concentration range of 2–240 μg L⁻¹ (R² = 0.996) with the detection limit of 0.1 μg L⁻¹ level. The reproducibility (RSD %, n = 6) of the new IL bonded fused-silica fiber (8.9%) was better than the physically coated fiber (12%) suggesting that the proposed chemically IL-modified fiber is more robust than the physically IL-modified fiber. The optimum extraction conditions were the followings: 40 °C extraction temperature, 12 min extraction time, 30 s desorption time and sample agitation at 200 rpm.     

Online preconcentration in capillary electrophoresis with contactless conductivity detection for sensitive determination of sorbic and benzoic acids in soy sauce

A sensitive method of online preconcentration followed by capillary electrophoresis with capacitively coupled contactless conductivity detection (CE-C⁴D) is evaluated as a novel approach for the determination of benzoic acid and sorbic acid in soy sauce. The online preconcentration technique, namely field-enhanced sample injection, coupled with CE-C⁴D were successfully developed and optimized. In order to reduce the complex matrix interference resulting from the constituents of soy sauce, a suitable sample clean-up procedure was also investigated for real sample pretreatment. Under optimized conditions, sorbic acid and benzoic acid were well separated within 10 min, and the detection limits were 0.05 μM (5.6 μg L⁻¹) and 0.08 μM (9.8 μg L⁻¹), respectively. The accuracy was tested by spiking 10.0 mg L⁻¹ and 100.0 mg L⁻¹ of standards in the soy sauce samples, and the recoveries were 95-99%, respectively. Results of this study show a great potential for the proposed method as a tool for the fast screening of benzoic acid and sorbic acid in a complex matrix.     

Determination of some refractory elements and Pb by fluorination assisted electrothermal vaporization inductively coupled plasma mass spectrometry with platform and wall vaporization

Platform and wall vaporization for electrothermal vaporization (ETV)-inductively coupled plasma mass spectrometry (ICP-MS) determination of some refractory elements (Ti, V, Cr, Mo, La and Zr) and Pb were comparatively studied with the use of poly (tetrafluoroethylene) (PTFE) as fluorinating reagent. The factors affecting the vaporization behaviors of the target analytes in the platform and tube wall vaporization including vaporization temperature and time, pyrolytic temperature and time were studied in detail, and the flow rates of carrier gas/auxiliary carrier gas, were carefully optimized. Under the optimal conditions, the signal profiles, signal intensity, interferences of coexisting ions and analytical reproducibility for wall and platform vaporization ETV-ICP-MS were compared. It was found that both wall and platform vaporization could give very similar detection limits, but the platform vaporization provided higher signal intensity and better precision for some refractory elements and Pb than the wall vaporization. Especially for La, the signal intensity obtained by platform vaporization was 3 times higher than that obtained by wall vaporization. For platform vaporization ETV-ICP-MS, the limits of detection (LODs) of 0.001 μg L⁻¹ (La) ~ 0.09 μg L^− 1 (Ti) with the relative standard deviations (RSDs) of 1.5% (Pb) ~ 15.5% (Zr) were obtained. While for wall vaporization ETV-ICP-MS, LODs of 0.005 μg L^− 1 (La) ~ 0.4 μg L^− 1 (Pb) with RSDs of 3.2% (Mo) ~ 12.8% (Zr) were obtained. Both platform and tube wall vaporization techniques have been used for slurry sampling fluorination assisted ETV-ICP-MS direct determination of Ti, V, Cr, Mo, La, Zr and Pb in certified reference materials of NIES No. 8 vehicle exhaust particulates and GBW07401 soil, and the analytical results obtained are in good agreement with the certified values.     

Determination of geosmin and 2-methylisoborneol in water and wine samples by ultrasound-assisted dispersive liquid-liquid microextraction coupled to gas chromatography-mass spectrometry

A fast, simple and environmentally friendly ultrasound-assisted dispersive liquid–liquid microextraction (USADLLME) procedure has been developed to preconcentrate geosmin and 2-methylisoborneol (MIB) from water and wine samples prior to quantification by gas chromatography–mass spectrometry (GC–MS). A two-stage multivariate optimization approach was developed by means of a Plackett–Burman design for screening and selecting the significant variables involved in the USADLLME procedure, which was later optimized by means of a circumscribed central composite design. The optimum conditions were: solvent volume, 8 μL; solvent type: tetrachloroethylene; sample volume, 12 mL; centrifugation speed, 2300 rpm; extraction temperature 20 °C; extraction time, 3 min; and centrifugation time, 3 min. Under the optimized experimental conditions the method gave good levels of repeatability with coefficient of variation under 11% (n = 10). Limits of detection were 2 and 9 ng L⁻¹ for geosmin and MIB, respectively. Calculated calibration curves gave high levels of linearity with correlation coefficient values of 0.9988 and 0.9994 for geosmin and MIB, respectively. Finally, the proposed method was applied to the analysis of two water (reservoir and tap) samples and three wine (red, rose and white) samples. The samples were previously analyzed and confirmed free of target analytes. Recovery values ranged between 70 and 113% at two spiking levels (0.25 μg L⁻¹ and 30 ng L⁻¹) showing that the matrix had a negligible effect upon extraction. Only red wine showed a noticeable matrix effect (70–72% recovery). Similar conclusions have been obtained from an uncertainty budget evaluation study.     

Determination of sibiromycin and its natural derivatives using new analytical and structural approaches

A new separation and quantification method using ultra high-performance liquid chromatography (UHPLC) with UV detection was developed for the detection of sibiromycin in fermentation broth of Streptosporangium sibiricum. The solid phase extraction method based on cation-exchange was employed to pre-concentrate and purify fermentation broth containing sibiromycin prior to UHPLC analysis. The whole assay was validated and showed a linear range of detector response for the quantification of sibiromycin in a concentration from 3.9 to 250.0 μg mL⁻¹, with correlation coefficient of 0.999 and recoveries ranging from 71.66 ± 3.55% to 74.76 ± 5.18%. Method limit of quantification of the assay was determined as 0.18 μg mL⁻¹ and was verified with resulting RSD of 9.6% and accuracy of 97.6%. The developed assay was used to determine the sibiromycin production in 12 different fermentation broths. Moreover, several natural sibiromycin analogues/derivatives were described with pilot characterization using off-line mass spectrometry: the previously described dihydro-sibiromycin (DH-sibiromycin) and tentative bis-glycosyl forms of sibiromycin and its dihydro-analogue.     

Application of d-SPE before SPE and HPLC-FLD to Analyze Bisphenols in Human Breast Milk Samples

In this study, we propose a simple, cost-effective, and sensitive high-performance liquid chromatography with fluorescence detection (HPLC-FLD) for the simultaneous determination of seven bisphenols (bisphenol F (BPF), bisphenol E (BPE), bisphenol B (BPB), BADGE (bisphenol A diglycidyl ether), BADGE∙2H₂O, BADGE∙H₂O, BADGE∙2HCl) in human breast milk samples. The dispersive solid phase extraction (d-SPE) coupled with solid phase extraction (SPE) procedure performed well for the majority of the analytes with recoveries in the range 57–88% and relative standard deviations (RSD%) of less than 9.4%. During the d-SPE stage, no significant matrix effect was observed thanks to the application of different pairs of salts such as zirconium-dioxide-based sorbents (Z-Sep or Z-Sep +) and primary secondary amine (PSA) or QuEChERS Enhanced Matrix Removal-Lipid (EMR-Lipid) and PSA. The method limits of quantification (mLOQs) for all investigated analytes were set at satisfactory low values in the range 171.89–235.11 ng mL⁻¹. Analyte concentrations were determined as the average value from human breast milk matrix samples. The results show that the d-SPE/SPE procedure, especially with the application of EMR-Lipid and PSA, could be used for further bisphenol analyses in human breast milk samples.     

Simple spectrophotocolorimetric method for quantitative determination of gold in nanoparticles

A simple spectrophotocolorimetric method devoted to the measurement of gold content in nanoparticles (NPs) was developed. It includes two steps: (i) metal gold NPs (Au NPs) are oxidized into the AuCl₄⁻ anion using a 5 × 10⁻² M HCl-1.5 × 10⁻² M NaCl-7 × 10⁻⁴ M Br₂ solution, next (ii) AuCl₄⁻ concentration is measured using a spectrophotometric assay based on the reaction of AuCl₄⁻ with the cationic form of Rhodamine B to give a violet ion pair complex. This latter is extracted with diisopropyl ether and the absorbance of the organic complex is measured at 565 nm. The method is linear in the range 6-29 μM of AuCl₄⁻ with a limit of detection of 4.5 μM.The analytical method was optimized with respect of bromine excess to obtain complete Au NPs oxidation. The method was applied to two types of Au NPs currently under investigation: citrate-stabilized Au NPs and Au NPs capped with dihydrolipoic acid (Au@DHLA). Both the gold content of Au NPs and the concentration of NPs (using NP diameter measured by transmission electron microscopy) have been calculated.     

Determination of bisphenol A based on chemiluminescence from gold(III)-peroxymonocarbonate

Peroxymonocarbonate (HCO₄⁻) was produced by the online reaction of bicarbonate with hydrogen peroxide. A strong chemiluminescence (CL) was observed when HCO₄⁻ reacted with AuCl₄⁻ without any special CL reagent. When bisphenol A (BPA) was added to AuCl₄⁻-HCO₄⁻ CL system, the CL emission was inhibited significantly. This new CL system was developed as a flow-injection method for the determination of BPA. Under the optimum experimental conditions, the inhibited CL intensity was linearly related to the concentration of BPA from 0.3 to 80 μM (R = 0.9958). The detection limit of BPA was 0.08 μM. The relative standard deviation for 12 repeated measurements of 1.0 μM BPA was 2.9%. The interferences of some cationic ions can be removed by an online cation-exchange column. The applicability of the present CL system was demonstrated for the sensitive and selective determination of BPA in real samples (mineral water bottle, baby bottle, beverage bottle and polycarbonate container). Based on the CL spectrum, UV-visible adsorption spectra, and the quenching effect of reactive oxygen species scavengers, a possible CL mechanism was proposed.     

Cationic polymerization of isobutyl vinyl ether coinitiated with heteropolyacid or its salts in aqueous medium

The suspension cationic polymerization of isobutyl vinyl ether (IBVE) in aqueous medium could be achieved by using H₃PW₁₂O₄₀, AlPW₁₂O₄₀, FePW₁₂O₄₀, K₃PW₁₂O₄₀, or Na₃PW₁₂O₄₀ as efficient water‐tolerant coinitiators in the presence of HCl. The addition reaction of IBVE with H₂O occurred to form IBVE–H₂O adduct and then subsequent decomposition immediately took place or turned to acetaldehyde diisobutyl acetal (A) in the presence of AlPW₁₂O₄₀, and ( A ) decomposed rapidly to form 2‐isobutanol ( B ) and acetaldehyde ( C ). Cationic polymerization of IBVE in aqueous medium was promoted greatly with increasing HCl concentration and proceeded extremely rapidly to get high polymer yield even at low concentration of AlPW₁₂O₄₀ of 0.3 mM. A sufficient amount of HCl was needed to decrease the hydrolysis of initiator IBVE–HCl and to accelerate the polymerization in aqueous medium simultaneously. The yield and molecular weight of poly(IBVE) increased with increasing concentrations of HCl and AlPW₁₂O₄₀ or with decreasing temperature. The isotactic‐rich poly(IBVE)s with m diad of around 60%, having M_n of 1200–4500 g mol^?1 and monomodal molecular weight distribution could be obtained via cationic polymerization of IBVE in aqueous medium. This is the first example of cationic polymerization of IBVE in aqueous medium coinitiated by heteropolyacid and its salts. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Cytotoxic copper(II) complex of tripyridoquinoxaline with DNA hydrolase activity

A monomeric copper(II) complex, [Cu(tpq)₂(H₂O)₂](ClO₄)₂, (tpq = tripyridoquinoxaline), has been synthesized and characterized spectroscopically. This complex has been found to bind DNA intercalatively and the DNA binding constant, K_b, for this complex has been determined from absorption measurements and was found to be (5.7 ± 0.3) × 10³ M⁻¹. This complex successfully promotes hydrolytic cleavage of plasmid DNA, producing single and double DNA strand breaks in the absence of any added cofactor. The amount of conversion of the supercoiled form of plasmid to the nicked circular form depends on the concentration of the copper complex as well as the duration of the incubation of the complex with DNA. The rate of conversion of SC to NC has been determined to be 2.65 × 10⁻⁴ s⁻¹ at pH 7.2 in the presence of 80 μM of the complex. This complex has also been shown to be cytotoxic towards A549 lung adenocarcinoma cells. This complex has been shown to bring about apoptosis of the cancerous A549 cell line.     

The synthesis of oxazolo- and oxazino[3,2-d] [1,4]benzodiazepinones

Cyclization of 2′-benzoyl-4′-chloro-2-[(2-hydroxypropyl)amino]acetanilide (8) and 2′-bcnzoyl-4-ehloro-2-[(3-hydroxypropyl)amino]acetanilide ( 7 ) led to the respective oxazolo (3) and oxazino (5) analogs of 7-chloro-1,3-dihydro-5-phenyl-2H-1,4-benzodiazepin-2-one. Cyclization of 2′-benzoyl-4′-chloro-2-[2,3-dihydroxypropyl)amino]acetanilide ( 9 ) could produce either the oxazolo ( 4 ) or oxazino ( 10 ) analog. Data is presented to show that cyclization occurred to give the oxazolo (4) analog.     

Effective indirect enrichment and determination of nitrite ion in water and biological samples using ionic liquid-dispersive liquid-liquid microextraction combined with high-performance liquid chromatography

An ionic liquid dispersive liquid–liquid microextraction high-performance liquid chromatography (IL-DLLME-HPLC) method for effective enrichment and determination of nitrite ion in water and biological samples was developed. The method was based on the reaction of nitrite ion with p-nitroaniline in the presence of diphenylamine in acid media and IL-DLLME of azo product. The optimization of reaction and extraction conditions, such as kind and concentration of acid, reaction time, volume of reaction solvent, temperature, kind of extraction and dispersive solvent, volume of extraction and dispersive solvent, addition of salt, extraction and centrifugal time were studied. Under the optimal conditions, 1-octyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide IL-DLLME procedure provided high enrichment factor of 430 and good extraction recovery of 91.7% for nitrite ion. The linearity was observed in the range of 0.4–500.0 μg L⁻¹ with good correlation coefficient (r² = 0.9996). The relative standard deviations (RSDs) for five replicate measurements varied between 1.5% and 4.8%. The limit of detection of the method (S/N = 3) was 0.05 μg L⁻¹. The interference effect of some anions and cations was also tested. The developed method allowed achieving an excellent enrichment factor, yielding a lower LOD in comparison with other methods. Moreover, the proposed method was able to analyze nitrite ion in water and biological samples with satisfactory recovery ranged from 96.5% to 107.3%.     

Carbon nanofibers extracted from soot as a sorbent for the determination of aromatic amines from wastewater effluent samples

The isolation and characterization of carbon nanofibers from soot obtained by burning natural oil is reported. The fibers were extracted from the soot with tetrahydrofuran followed by sonication. The carbon nanofibers were mixed with poly(vinyl alcohol) and electrospun to get the nanofiber mat. The extraction ability of electrospun nanofibers for the separation and preconcentration of aromatic compounds such as 3-nitroaniline, 4-chloroaniline, 4-bromoaniline and 3,4-dichloroaniline were tested and efficiently evaluated using high performance liquid chromatography. Under optimized conditions, the method showed good linearity in a range of 0.5–50 μg L⁻¹ with correlation coefficient ranging from 0.989 to 0.998. High precision of the extraction with RSD values of 4.5–5.8% and low LOD value in a range of 0.009–0.081 μg L⁻¹ for all aniline compounds were achieved. The proposed microextraction method offers advantages such as easy operation, high recovery, fast extraction, minimal use of organic solvent and elimination of tedious solvent evaporation and reconstitution steps.     

A new analytical methodology for a fast evaluation of semi-volatile polycyclic aromatic hydrocarbons in the vapor phase downstream of a diesel engine particulate filter

A new sampling method was developed to collect vapor-phase polycyclic aromatic compounds (PAHs) downstream of a diesel engine equipped with a diesel particulate filter (DPF). This configuration allowed us to collect separately the particulate phase, which was trapped inside the DPF, and the vapor phase, which was sampled downstream of the DPF. PAHs, which were not predominantly absorbed into the poor organic fraction of the diesel soot, but were rather physically sorbed on high energetic adsorption sites, should be extracted using very drastic extraction conditions Microwave-assisted extraction using solvent mixtures composed of pyridine and diethylamine were used to desorb particulate PAHs, and the total PAH amounts corresponded to a very low value, i.e., 8 μg g⁻¹ or 0.24 μg km⁻¹, with a predominance of low weight PAHs. For collection of the vapor phase, gas bubbling in an aqueous medium was preferred to conventional methods, e.g., trapping on solid sorbents, for several reasons: aqueous trapping allowed us to use a solid phase enrichment process (SPE) that permitted PAH sampling at the sub-picogram levels. Consequently, low volume sampling was possible even if the sampling duration was very short (20 min). Additionally, the amount of time saved for the analysis was considerable when coupling SPE to the analytical system (liquid chromatography with fluorimetric detection). Solvent consumption for the overall sampling and analytical processes was also drastically reduced. Experiments on a diesel engine showed that vapor phase samples collected downstream of the DPF contained all of the 15 target priority PAHs, even the heaviest ones. The total vapor-phase PAH amount was 6.88 μg N m⁻³ or 10.02 μg km⁻¹, which showed that the gaseous fraction contains more PAHs than the particulate fraction. Partitioning coefficients (K_p) were estimated showing the predominance in the vapor phase of all the PAHs. However, the DPF technology effects a considerable decrease in the total PAH emission when compared to non-equipped diesel vehicles.