Regioselective intermolecular cycloalumination of cyclic allenes and ethylene with R<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript>AlCl<Subscript>3−<Emphasis Type="Italic">n</Emphasis></Subscript>, catalyzed by titanium and zirconium complexes

Intermolecular cycloalumiation of cyclic 1,2-dienes and ethylene with organoaluminum compounds R _n AlCl_3−n in the presence of zirconium- and titanium-based catalysts occurred regioselectively with formation of unsaturated bicyclic organoaluminum compounds in high yields.     

Development of PGM-free catalysts for automotive applications

The activity of Ag-based catalysts in soot oxidation using NO₂ and oxygen as oxidants has been characterized in laboratory tests (TGA) and under real conditions on an engine dynamometer. Under low-temperature NO₂-assisted and high-temperature O₂-assisted soot oxidation conditions, the activity of Ag-based catalysts was found to be comparable or higher than that of commercial Pt-catalysts. In addition, Ag-based compositions also revealed noticeable NO _x storage, some passive NO _x reduction ability, and activity in NO oxidation. Ag-catalysts characterized in the present paper may be promising for the retrofit applications and high-temperature periodical regenerations with air for diesel passenger cars.     

Alkaline‐Earth Metal Doped K‐V Catalysts for Diesel Soot Combustion–Preparation,Characterization and Catalytic Properties

The K‐V‐alkaline‐earth metal catalysts supported on α‐alumina ceramic substrate have been prepared. The morphology of the soot particulates deposited on prepared catalysts supported on α‐alumina ceramic substrate was described by scanning electron microscopy (SEM). The XRD was used to characterize the catalysts and their catalytic activities were evaluated by soot oxidation reaction using the TPR system. The SEM photographs presented that soot particles have a particle size of about 100 nm in diameter forming a loose contact with catalyst, which is resemble to the real situation for the catalyst application. The XRD and TPR study showed that the catalytic activities of the catalysts were improved through the cooperation of KNO₃ and some alkaline earth metal compounds. The soot onset ignition temperature at 310°C is the lowest by the cooperation of the crystalline phases KNO₃, KCaVO₄, and Ca₃(VO₄)₂ for the K‐V‐Ca catalyst with a molar ratio of 6:1:1. In addition, the catalyst containing higher KNO₃ content has an adsorption for CO₂. The all prepared K‐V‐Ba catalysts can adsorb more CO₂ at room temperature.     

Polymérisation “basse pression” de l'ethylène en préasence de noir de carbone

The polymerization of ethylene with Ziegler-Natta catalysts in the presence of carbon black has shown three characteristic features both with a heterogeneous catalyst, AlBu₃? TiCl₄, and with a soluble catalyst, Cl₂Ti(C₅H₅)₂? AlEt₂Cl. They are, in order of increasing importance: reactivity of the organoaluminum derivatives with surface chemical groups of the carbon black, adsorption of a certain amount of organoaluminum compounds on the carbon black surface, and influence of the specific surface of carbon black, which controls the dispersion degree of the catalytic system. Furthermore, it was possible to obtain polyethylene by this procedure, containing different amounts and different types of carbon black.     

Dependence of the catalytic activity of organoaluminum compounds and some of their complexes on their composition

The influence of the acidity of organoaluminum compounds and their complexes on the catalytic activity in polymerization of trioxane has been studied. It is found that the catalytic activity of organoaluminum compounds of the type R_nALX_3?n depends on n as well as the nature of R or X. Catalytic activity of the complexes also depends on the type of cocatalyst used. The change of electroconductivity in the course of formation of some initiator complexes has been studied and an attempt has been made to determine the relation between conductivity and polymerization activity.     

Catalytic removal of soot particles over MnCo<Subscript>2</Subscript>O<Subscript>4</Subscript> catalysts prepared by the auto-combustion method

Soot removal for exhaust gas from diesel engine has been addressed due to the more stringent legislation and environmental concerns. MnCo₂O₄ catalysts were systematically prepared using glucose as a fuel via the auto-combustion method and applied for soot removal. The as-prepared samples were characterized by X-ray diffraction (XRD), O₂-temperature-programmed oxidation (TPO) reaction and H₂-temperature-programmed reduction reaction (H₂-TPR). The catalytic activities for soot combustion were evaluated by micro activity test (MAT) with a tight contact mode between soot and catalysts. Compared with catalysts prepared by the solid state method without glucose, auto-combustion method in the presence of glucose can decrease the synthetic temperature, avoiding high temperature treatment and sintering. The catalysts prepared with glucose could catalyze soot oxidation effectively and the derived values of T₁₀, T₅₀, and T₉₀ were 326, 408, and 468 °C in a tight contact mode, respectively, showing a significant drop of T₁₀, T₅₀, and T₉₀ by 156, 177, and 178 °C for non-catalytic reaction.     

Polymerization of Cyclohexene Oxide By Organoaluminum Compounds

Abstract

The polymerization of cyclohexene oxide (CHO) by various organoaluminum compounds such as R₃Al (R = Me, Et, i-Bu), Et₂AlCl, and EtAlCl₂ is reported. Ethyl-substituted aluminum compounds were found to be very effective for this polymerization. As more chlorine atom is substituted on the aluminum atom, the polymer yield was increased though the molecular weight was decreased. The polymer yields at varying monomer-to-catalyst mole ratios (M/C) were similar (80–93%). The temperature and solvent effect for the present polymerization were also studied. The present poly(CHO) was a less stereoregular (atactic) isomer, regardless of catalysts and polymerization conditions. The resulting poly(CHO) was a white powder ad was soluble in aromatic and halogenated hydrocarbon solvents such as benzene, chlorobenzene, CCl₄, chloroform, etc.     

Coupled hydrogenation of alkenes and arenes in the presence of catalytic systems based on cobalt Bis(acetylacetonate) and tributylphosphine

The effect of the composition of the catalytic systems based on Co(acac)₂ and tertiary phosphines on the activity and efficiency of cobalt catalysts in the coupled hydrogenation of alkenes and arenes is reported. The process occurs in the presence of cobalt catalysts formed under the action of both organoaluminum compounds and tert-butoxy derivatives of complex aluminum hydrides. NMR and IR spectroscopic methods show that the interaction of the components of the catalytic systems yields mono- and/or trihydrido cobalt phosphine complexes, whose composition depends on the nature of the reducing agent and gas atmosphere. The homogeneous character of the process is hypothesized. The most probable schemes are proposed for the reaction mechanism, according to which the kinetic coupling of alkene (alkadiene) and arene hydrogenations is due to the fact that the reaction proceeds through a σ-alkyl or σ-alkenyl cobalt complex with two phosphorus-containing ligands.     

Promotional effect of cobalt addition on catalytic performance of Ce<Subscript>0.5</Subscript>Zr<Subscript>0.5</Subscript>O<Subscript>2</Subscript> mixed oxide for diesel soot combustion

A series of Co-modified Ce_0.5Zr_0.5O₂ catalysts with different concentrations of Co (mass %: 0, 2, 4, 6, 8, 10) was investigated for diesel soot combustion. Ce_0.5Zr_0.5O₂ was prepared using the coprecipitation method and Co was loaded onto the oxide using the incipient wetness impregnation method. The activities of the catalysts were evaluated by thermogravimetric (TG) analysis and temperature-programmed oxidation (TPO) experiments. The results showed the soot combustion activities of the catalysts to be effectively improved by the addition of Co, 6 % Co/Ce_0.5Zr_0.5O₂ and that the 8 % Co/Ce_0.5Zr_0.5O₂ catalysts exhibited the best catalytic performance in terms of lower soot ignition temperature (T_i at 349°C) and maximal soot oxidation rate temperature (T_m at 358°C). The reasons for the improved activity were investigated by X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), H₂ temperature-programmed reduction (H₂-TPR), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). These results revealed that the presence of Co could lower the reduction temperature due to the synergistic effect between Co and Ce, thereby improving the activity of the catalysts in soot combustion. The 6 % Co catalyst exhibited the best catalytic performance, which could be attributed to the greater amounts of Co³⁺ and surface oxygen species on the catalyst.     

Structure and chemical behavior of an organoaluminum compound [Rb2AlOCR′NPh]2, a stereospecific catalyst for polymerization of acetaldehyde

A series of organoaluminum compounds [R₂AlOCR′NPh]₂, which are the reaction products between trialkylaluminum compounds and secondary acid amides and are excellent catalysts for stereospecific polymerizations of aldehydes, were isolated in the crystalline state. Chemical behavior of such compounds toward Lewis acids and bases were interpreted in terms of the structures of [Me₂AlOCPhNPh]₂ and its trimethylamine oxide complex Me₃NO·AlMe₂OCPhNPh which were determined by X-ray structure analyses. Reaction products of primary and tertiary acid amides with trialkylaluminum compounds were also studied.     

DTA,TG studies of catalytic oxidation of carbon particles over M2 III O3 (MIII=Al,Cr, Fe,Ni)

Carbonizate as a model soot has been submitted to oxidation using Al₂O₃, Cr₂O₃, Ni₂O₃ and Fe₂O₃ as catalysts in the temperature range from RT up to 1000°C. The results obtained indicate that Fe₂O₃ is the most active catalyst in soot oxidation. However, all the catalysts examined are active in transformation of carbonizate components. It has been shown that DTA and TG methods can be used as fast methods testing the carbonizate oxidation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Optimized Pt-MnOx interface in Pt-MnOx/3DOM-Al2O3 catalysts for enhancing catalytic soot combustion

The catalysts of three-dimensionally ordered macroporous (3DOM) Al₂O₃-supported core-shell structured Pt@MnO_x nanoparticles (3DOM-Pt@MnO_x/Al₂O₃) were successfully prepared by the gas bubbling-assisted membrane reduction-precipitation (GBMR/P) method. Pt@MnO_x core-shell nanoparticles (NPs) are highly dispersed on the inner surface of 3DOM-Al₂O₃ support. Pt@MnO_x/3DOM-Al₂O₃ catalysts, which combine both advantages of high-efficiency soot-catalyst contact by 3DOM-Al₂O₃ structure and the abundant active sites by the optimized Pt-MnO_x interface, exhibit high catalytic activities for soot combustion, and the catalytic activities are strongly dependent on the thickness of MnO_x shell. Among the catalysts, 3DOM-Pt@MnO_x/Al₂O₃-1 catalyst with optimized Pt-MnO_x interface shows the highest catalytic activity for soot combustion, i.e., its values of T₅₀ and S_CO2^m are 351 °C and 98.6%, respectively. The highest density of Pt-MnO_x active sites for adsorption-activation of gaseous O₂ is responsible for enhancing catalytic activity for soot combustion. Pt@MnO_x/3DOM-Al₂O₃ catalysts are promising to practical applications for the emission reduction of soot particles.     

In-situ UV-Raman study on soot combustion over TiO2 or ZrO2-supported vanadium oxide catalysts

UV-Raman spectroscopy was used to study the molecular structures of TiO₂ or ZrO₂-supported vanadium oxide catalysts. The real time reaction status of soot combustion over these catalysts was detected by in-situ UV-Raman spectroscopy. The results indicate that TiO₂ undergoes a crystalline phase transformation from anatase to rutile phase with the increasing of reaction temperature. However, no obvious phase transformation process is observed for ZrO₂ support. The structures of supported vanadium oxides also depend on the V loading. The vanadium oxide species supported on TiO₂ or ZrO₂ attain monolayer saturation when V loading is equal to 4 (4 is the number of V atoms per 100 support metal ions). Interestingly, this loading ratio (V₄/TiO₂ and V₄/ZrO₂) gave the best catalytic activities for soot combustion reaction on both supports (TiO₂ and ZrO₂). The formation of surface oxygen complexes (SOC) is verified by in-situ UV Raman spectroscopy and the SOC mainly exist as carboxyl groups during soot combustion. The presence of NO in the reaction gas stream can promote the production of SOC.     

Catalytic reactions of C3-cyclic olefins in the presence of metal complexes. 4. Ni complexes as catalysts for the [2+2]-cyclodimerization of spiro[2,3]hex-1-ene

Ni(0), Ni(I), and Ni(II) complexes, differing in the ligand environment of the central atom, bring about di-, tri-, and oligomerization of spiro[2,3]-hex-1-ene (SH). The most efficient catalyst for the [2+2]-cyclodimerization of SH is NiBr(PPh₃)₃, which gives virtually a single product, the SH cyclo dimer. It has been found that high conversion and selectivity in the [2+2]-cyclodimerization of SH is achieved by using organoaluminum compounds as catalysts.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 2, pp. 345–348, February, 1990.For previous communication, see [1].     

VOCs and carbonaceous particles removal assisted by NOx on alkali0.15/ZrO2 and Csx–M0.1/ZrO2 catalysts (M = Cu or Co)

The effect of alkali metals on the physicochemical characteristics of zirconium oxide and the properties of alkali metals in the oxidation of toluene and/or carbonaceous particles and/or conversion of nitrogen oxides have been studied. We observed that they had an effect on the structural and textural properties of ZrO₂. These solids were tested first in the oxidation of toluene and carbonaceous particles separately and secondly with both pollutants. Whatever the experiments, the sample Cs_0.15/ZrO₂ was found to be the catalyst the most active. The simultaneous removal of toluene and soot shows that the presence of toluene leads to a decrease in the temperature of the maximum soot oxidation rate, particularly with catalysts impregnated of Cs and Cu. The effect of the Cs/Co ratio on NO_x conversion and toluene oxidation was also studied. It was found that the oxidizing properties of NO_x can increase the conversion of toluene. This phenomenon occurs especially in the presence of catalysts with a low amount of alkali metal. For the oxidation of carbonaceous particles on the samples Cs/ZrO₂ impregnated with transition metals, the best performance is obtained for copper, although a decrease of the ratio Cs/Cu leads to a slower oxidation and a shift to higher temperatures.     

Efficient fuel cell catalysts emerging from organometallic chemistry

During the last few decades organometallic methodologies have generated a number of highly effective electrocatalyst systems based on mono‐ and bimetallic nanosparticles having controlled size, composition and structure. In this microreview we summarize our results in fuel cell catalyst preparation applying triorganohydroborate chemistry, ‘reductive particle stabilization’ using organoaluminum compounds, and the controlled decomposition of organometallic complexes. The advantages of organometallic catalyst preparation pathways are exemplified with Ru? Pt nanoparticles@C as promising anode catalysts to be used in direct methanol oxidation fuel cells (DMFC) or in polymer electrolyte fuel cells (PEMFC) running with CO‐contaminated H₂ as the feed. Recent findings with highly efficient PtCo₃@C fuel cell catalysts applied for the oxygen reduction reaction (ORR) and with the effect of Se‐doping on Ru@C ORR catalysts clearly demonstrate the benefits of organometallic catalyst synthesis. Copyright © 2010 John Wiley & Sons, Ltd.     

Bulk propylene polymerization in the presence of ansa-metallocenes of C 2 and C 1 symmetries: From a rigid thermoplastic to elastomeric stereoblock polypropylene

Bulk propylene polymerization in the presence of ansa-metallocenes with C ₂ and C ₁ symmetries has been studied. The catalytic activity, polymerization kinetics, and the molecular weight of polypropylene (PP) depend strongly on catalyst formation conditions. Mixtures of rac and meso isomers of metallocenes make it possible to rapidly produce a high-molecular-weight isotactic PP with high stereoregularity and mechanical characteristics and thus skip the stage of the isolation of pure rac isomer in the catalyst synthesis. The ability of triisobutylaluminum to serve as a cocatalyst is studied for ansa-metallocenes of C ₁ symmetry. In this case, the molecular weight of PP is higher, indicating that organoaluminum compounds participate in chain termination reactions. An increase in the reaction temperature results in an increase in the stereoregularity and crystallinity of PP. Polypropylene synthesized using ansa-metallocenes of C ₁ symmetry has good elastomeric properties.     

Polymerizations with homogeneous chromium catalysts

Homogeneous catalysts derived from chromium complexes and organo-aluminum compounds have been discovered which effect the polymerization of ethylene and the oligomerization of simple olefins. The applicable chromium derivatives are halide complexes of the type CrX₂L₂, CrX₂L₂(NO)₂, CrX₃L₃, and [CrX₃L₂]₂, wherein the ligands L are pyridine, tri-n-butylphosphine, and the like. The nature of the systems with regard to polymerization or oligomerization has been demonstrated to be primarily a function of the organoaluminum halide cocatalyst and of the reaction conditions. In general, systems containing ethylaluminum dichloride cocatalyst afford simple oligomerization products at reaction temperatures above 50°C, while at lower temperatures those containing organoaluminums of the type R₃Al₂X₃ or R₂AlX effect the polymerization of ethylene as the principal reaction.     

Synthesis and transformations of metallacycles 44. Cycloalumination of methylenecyclobutane terpene derivatives with Et3Al catalyzed by Cp<Subscript>2</Subscript>ZrCl<Subscript>2</Subscript>

Cycloalumination of methylenecyclobutane terpene derivatives (d(+)-camphor, (+)-camphene, β-pinene, and l(–)-menthol) with Et₃Al catalyzed by Cp₂ZrCl₂ produced novel spirofused organoaluminum compounds in high yields. The synthesized compounds were in situ transformed into the corresponding spiro tetrahydroselenophenes and spiro phospholanes.     

Diesel Soot Combustion over Mn2O3 Catalysts with Different Morphologies: Elucidating the Role of Active Oxygen Species in Soot Combustion

Catalytic diesel soot combustion was examined using a series of Mn₂O₃ catalysts with different morphologies, including plate, prism, hollow spheres and powders. The plate‐shaped Mn₂O₃ (Mn₂O₃‐plate) exhibited superior carbon soot combustion activity compared to the prism‐shaped, hollow‐structured and powdery Mn₂O₃ under both tight and loose contact modes at soot combustion temperatures (T₅₀) of 327 °C and 457 °C, respectively. Comprehensive characterization studies using scanning electron microscopy, scanning transmission electron microscopy, X‐ray diffraction, X‐ray photoelectron spectroscopy, temperature‐programmed reduction and oxygen release measurements, revealed that the improved activity of Mn₂O₃‐plate was mainly attributed to the high oxygen release rate of surface‐adsorbed active oxygen species, which originated from oxygen vacancy sites introduced during the catalyst preparation, rather than specific surface‐exposed planes. The study provides new insights for the design and synthesis of efficient oxidation catalysts for carbon soot combustion as well as for other oxidation reactions of harmful hydrocarbon compounds.