Determination of pentachlorophenol residues in wine and corks by solvent extraction methodology and specific gas chromatography detection

Summary A gas chromatographic methodology with selective detection is presented for the analysis in wines and corks of pentachlorophenol residues, which are suspected to be the most likely precursors of some off-flavours described in several wine samples. After derivatisation, pentachlorophenol acetate residues were monitored by electrolytic conductivity detection and/or mass spectrometric detection in the selective ion mode at m/z 264 and 266. Recoveries varied from 80 to 96% for wine samples fortified with 5 to 100 g l^–1 and from 83 to 91% for corks (fortified at 25 to 100 g kg^–1). The proposed methodology allowed for a determination limit of g l^–1 for wine and 10 g kg^–1 for corks.     

Differential pulse voltammetric methods for the simultaneous estimation of uranium-iron and uranium-cadmium mixtures in solution

Differential pulse voltammetric methods have been developed for the simultaneous estimation of the constituents of uranium-iron and uranium-cadmium mixtures in solution. A mixture of 1M H₃PO₄–1M KH₂PO₄ (with a pH1.5), was found to be the most ideal supporting electrolyte for both methods, among many that were evaluated for their suitability. In uranium-iron mixtures the calibration for iron was found to be linear up to 150 g ml^–1 (r²=0.9986), while that of uranium up to 500 g ml^–1 (r²=0.999). Iron at 6.7 g ml^–1 level could be determined in the presence of 800 fold uranium (wt/wt) without significant interference. Uranium at 21 g ml^–1 level could be analyzed with 5-fold iron (wt/wt). This upper limit of iron was due to the precipitation of iron as phosphate. In the case of uranium — cadmium mixtures, cadmium calibration for cadmium was found to be linear up to 1300 g ml^–1 (r²=0.9993). Concentration levels of 4.6 g ml^–1 Cd could be determined at a 500-fold excess (wt/wt) of uranium. Uranium calibration was linear up to 500 g ml^–1 (r²=0.999) and 21 g ml^–1 uranium could tolerate up to a 1000-fold excess of cadmium (wt/wt). Both procedures could tolerate 10 g ml^–1 levels of metal ions, such as chromium, copper, manganese, molybdenum and vanadium.     

The determination of boron in biological materials by neutron irradiation and prompt gamma-ray spectrometry

A prompt-gamma neutron activation technique has been developed using the (n, ) apparatus situated at the O degree through-tube of the Imperial College CONSORT II Reactor with a thermal neutron flux at the target position of approximately 2×10⁶ n cm^–2 sec^–1, and a Compton-suppression system involving a lithium-drifted germanium (Ge(Li)) detector and a sodium iodide anti-Compton shield. Boron levels of 1–5 g g^–1 (detection limit 0.05 g B for 10,000 sec period of measurement) can be attained using the Compton-suppression system with graphical inter-polation correction for the 472 keV sodium-ray peak contribution to the Doppler-broadened 478 keV boron gamma-ray peak resulting from the¹⁰B(n, )⁷Li reaction. Very good agreement is reached for boron levels compared using this system for various Standard Reference Materials and other published values. Measurement of the boron content of bone and tooth samples from rheumatoid arthritis individuals shows lower levels, (p<0.05); 16.13±7.53 g g^–1, when compared with a control population; 19.79±4.18 g g^–1. A positive correlation existed between the boron content of bone and tooth material for each study group. Results indicate that boron availability may be associated with rheumatoid arthritis.     

Semi-automatic catalytic titration of some aminopoly-carboxylic acids,copper(II), and cobalt(II)

Summary A semi-automatic potentiometric method is described for the catalytic titrimetric determination ofg amounts of some aminopolycarboxylic acids. The method is based on their inhibitory effect on the copper(II)-catalyzed periodate-thiosulfate reaction. Amounts of EDTA in the 0.7–600g range (10^–6–8×10^–5 M), of DCTA in the 7–7000g range (10^–6–10^–3 M), of EGTA in the 0.8–800g range (10^–7–10^–4 M), and of DTPA in the 4–800g range (5×10^–7–10^–4 M) were determined with average relative errors and coefficient of variation of about 0.4–1%. The method has also been used for the indirect catalytic titrimetric determination ofg amounts of Cu²⁺ and Co²⁺ ions with about the before mentioned accuracy and precision.

---

Halbautomatische katalytische Titration einiger Aminopolycarbonsäuren sowie von Cu(II) und Co(II)

Zusammenfassung Eine halbautomatische potentiometrische Methode zur katalytischen Maßanalyse von Mikrogrammengen einiger Aminopolycarbonsäuren wurde angegeben. Sie beruht auf dem Hinderungseffekt gegenüber der Cu(II)katalysierten Perjodat-Thiosulfatreaktion. EDTA in Mengen von 0,7–600g, DCTA in Mengen von 7–7000g, EGTA in Mengen von 0,8–800g und DTPA in Mengen von 4–800g wurden mit einem mittleren relativen Fehler von etwa 0,4–1% bestimmt. Das Verfahren wurde auch zur Bestimmung von Cu(II) und Co(II) mit der angeführten Genauigkeit verwendet.

     

Spectrophotometric and derivative spectrophotometric determination of palladium(II) using pyridopyridazine dithione in the presence of non-ionic surfactant

Pyridopyridazine dithione (PPD) was synthesized as a new sensitive and selective reagent for spectrophotometric and derivative spectrophotometric determination of palladium(II). In aqueous and micellar medium, PPD forms 1:4 complexes having molar absorptivities of 4.68 × 10⁴ and 5.74 × 10⁴lmol^–1 cm^–1 at 570 and 615 nm, respectively. Beer's law was obeyed up to 2.2 and 2.5 g ml^–1 with detection limits of 0.2 and 0.1g ml^–1. The relative standard deviations for 1.23g ml^–1 were 2.6 and 1.3%, in the absence and presence of Triton X-100. In fourth-derivative mode, the regression equation, linear range, detection limit and RSD for 0.075 g ml^–1 wereD ₄ = 4.3C + 1.5 × 10^–3, 0.013 – 0.23 g ml^–1, 3.7 ng ml–1 and 0.78%, respectively. The ionization constants of the reagent and stability constants of the complexes were evaluated. The method is free from interference by most common metal ions and anions. The method was applied for determination of palladium in activated charcoal.     

Development and Validation of an HPTLC–Densitometric Method for Determination of ACE Inhibitors

A high-performance thin layer chromatographic method coupled with densitometric analysis has been developed for measurement of benazepril and cilazapril, both pure and in their commercial dosage forms. The active substances were extracted from tablets with methanol (mean recovery 102%) and chromatographed on silica gel 60 F₂₅₄ HPTLC plates in horizontal chambers with ethyl acetate–acetone–acetic acid–water, 8:2:0.5:0.5 (v/v), as mobile phase. Chromatographic separation of these ACE inhibitors was followed by UV densitometric quantitation at 215 nm. Calibration plots were constructed in the range 0.4 to 2.0 g L^–1 for benazepril (2.0–10.0 g spot^–1) and from 0.5 to 1.5 g L^–1 for cilazapril (4.0–12.0 g spot^–1) with good correlation coefficients (r 0.990). The method was used to determine benazepril and cilazapril in pharmaceutical preparations with satisfactory precision (1.4% < RSD < 5.6%) and accuracy (1.7 < RE < 5.1).     

Characterization of airborne particulates by laser microprobe mass analysis

Summary Laser microprobe mass analysis (LAMMA) was applied to characterize aerosol particles collected and separated from 16m to 0.06m by a low pressure cascade impactor. Positive ion LAMMA spectra showed characteristic molecular peaks such as PbCl⁺, a series of Si₂O⁺–Si₂O₄ ⁺ and NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, and TiO⁺ in 0.06–0.12m, 0.5–1m and 4–8m fraction, respectively. In the negative ion LAMMA spectra, it was observed that the fragment peaks of sulfate ions were deficient above 2m and those of nitrate ions were deficient under 2m. LAMMA allows remarkable insights into the chemical nature of aerosol particles.

---

Charakterisierung luftgetragener Teilchen durch Laser-Microprobe-Massenspektrometrie

Zusammenfassung Laser-Microprobe-Spektrometrie (LAMMS) wurde zur Analyse atmosphärischen Aerosols herangezogen, welches im Korngrößenbereich zwischen 16m und 0.06m mit einem Niederdruckkaskadenimpaktor fraktioniert gesammelt wurde. Positive LAMMS-Spektren zeigten charakteristische molekulare Peaks, wie etwa PbCl⁺, eine Serie von Si₂O⁺–Si₂O₄ ⁺ und NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, sowie TiO⁺ in der 0,06–0,12-m,- 0,5–1–m- bzw. 4–8-m-Fraktion. In den negativen LAMMS-Spektren konnten über 2m keine Fragmentpeaks für Sulfationen, unter 2m. keine für Nitrationen beobachtet werden. LAMMS ermöglicht eine bemerkenswerte Einsicht in die chemische Natur von Aerosolteilchen.

     

Determination of Dextromethorphan and Dextrorphan in Human Urine by High Performance Liquid Chromatography for Pharmacogenetic Investigations

The aim of the present study was to develop a sensitive method to measure dextromethorphan and dextrorphan in urine by HPLC to support pharmacogenetic studies in ethnic groups. Linearity was assessed in the range: 0.015–10 g mL^–1 for dextromethorphan and 1-10 g mL^–1 for dextrorphan. Inter and intra-day coefficients of variation were < 10%. Limits of detection and quantitation were 0.003 g mL^–1 and 0.015 g mL^–1 for dextromethorphan and 0.24 g mL^–1 and 1.0 g mL^–1 for dextrorphan, respectively. The method is reliable in helping determine the phenotype of Mexican ethnic groups using model drugs such as dextromethorphan.     

Zur Bestimmung N-substituierter Aniline mit Natriumchlorit

Zusammenfassung Es wird eine photometrische Bestimmungsmethode beschrieben für Anilin (40–720 g/ml), Monoäthylanilin (90–1650 g/ml) und Diäthylanilin (100–1600 g/ml) mit Natriumchlorit in äthanolisch-wäßrigen Lösungen, sowie für Diäthylanilin (85–1140 g/ml) und Dimethylanilin (30–330 g/ml) neben den primären und sekundären Aminen in essigsaurer Lösung mit demselben Reagens. Das Verfahren liefert gute Ergebnisse.

---

Summary A photometric procedure is described for the determination of aniline (40–720 g/ml), monoethylaniline (90–1650 g/ml), and diethylaniline (100–1600 g/ml) with sodium chlorite in aqueous ethanolic solutions and of diethylaniline (85–1140 g/ml) and dimethylamline (30 to 330 g/ml) in presence of the primary and secondary amines in acetic acid solution using the same reagent. Good results have been obtained,

     

Electrothermal AAS studies of Sm, Eu, Dy, and Er separated from uranium

Summary Studies were conducted on the assay of Sm, Eu, Dy and Er separated from uranium using aqueous standards by electrothermal AAS with Massmann type graphite furnace. The working curves were found to be linear in the ranges Sm (1–10 g/ml), Eu (0.05–0.6 g/ml), Dy (0.1–0.8 g/ml) and Er (0.1–1.0 g/ml). The values obtained for synthetic samples agreed favourably with those obtained by emission spectrographic method. Experiments using pyrolytic carbon coated tubes with and without pretreatment by La, Ta and Y have shown an enhancement with treatment upto a maximum of 15% and improve the memory effect marginally. The effect of Ta treatment was found to be singularly useful in improving the general behaviour of Sm. The interference effects of lanthanides, other than the analyte, were found to be negligible. However, the presence of uranium was found to affect the absorbance. The absorbance of Eu was found to be nearly independent of uranium after an initial increase. On the other hand, the absorbance of other elements studied was found to drastically decrease after an initial enhancement. Detailed investigations of temperature dependence of absorbance were carried out using Eu, Dy and Er. The differences in the behaviour of these elements is attributed to probable differences in the modes of their atomization.

---

Untersuchung von aus Uran abgetrenntem Samarium, Europium, Dysprosium und Erbium durch elektrothermische Atomabsorptions-Spektralphotometrie

Zusammenfassung Die Untersuchungen wurden mit Hilfe des Graphitrohrofens nach Maßmann durchgeführt. In folgenden Bereichen ergaben sich lineare Eichkurven: Sm 1–10 g/ml, Eu 0,05–0,6 g/ml, Dy 0,1–0,8 g/ml, Er 0,1-1,0 g/ml. Die aus synthetischen Proben erhaltenen Ergebnisse stimmten gut mit den durch Emissionsspektrographie erhaltenen überein. Versuche wurden mit Röhren mit pyrolytischen Kohlenstoffüberzug mit und ohne Vorbehandlung durch La, Ta und Y durchgeführt und ergaben eine bis 15%ige Steigerung durch die Behandlung sowie eine mäßige Besserung des Memoryeffektes. Eine Behandlung mit Ta war besonders für Sm vorteilhaft. Störungen durch andere Lanthanide waren vernachlässigbar. Uran beeinflußte jedoch die Absorption. Im Falle von Eu zeigte sich nach anfänglicher Zunahme fast eine Unabhängigkeit, während bei den anderen untersuchten Elementen nach anfänglicher Zunahme eine beträchtliche Abnahme auftrat. Mit Eu, Dy und Er wurde ebenfalls die Temperaturabhängigkeit der Absorption untersucht. Festgestellte Unterschiede im Verhalten werden auf unterschiedliche Atomisierung zurückgeführt.

     

Determination of traces of sodium alkylbenzenesulphonate by high-performance liquid chromatography. Application to water

Summary For the trace determination of sodium alkylbenzenesulphonate (ABS) by HPLC the following conditions were employed: Shimadzu ZORBAX SIL Column (5 m, 4.6 mm i.d. x 150 mm) as stationary phase, 0.2% ammoniaethanol (v/v) as mobile phase, UV detector at 225 nm, injection volume 12 l. The chromatograms of ABS were simple and sharp (detection limit of ABS 0.02 g in 12 l of ethanol). The calibration curves of ABS were linear in a concentration range of 0.03 0.3 g in 12 l of ethanol. In the case of linear sodium dodecylbenzenesulphonate positive errors of 1 4% were caused by non-ionic surfactants or laurylsulphate (6 times excess), 10 50% positive errors were caused by 2 6 times excess of household detergents.Standard water samples containing ABS were treated with a weak base anion-exchange resin, the adsorbed ABS were eluted, and then determined either by HPLC or by the methylene blue spectrophotometric method. Recoveries of ABS in water were about 92 107% by HPLC.

---

Bestimmung von Spuren Natriumalkylbenzolsulfonat mit Hilfe der HPLC. Anwendung auf Wasser

Zusammenfassung Für die Spurenbestimmung von Natriumalkylbenzolsulfonat (ABS) durch HPLC werden die folgenden Bedingungen empfohlen:Shimadzu ZORBAX SIL (5 m, 4,6 mm x 150 mm) als stationäre Phase, 0,2% Ammoniak/Ethanol als mobile Phase, UV-Detektor bei 225 nm, Injektionsvolumen 12 l. Die erhaltenen Chromatogramme sind einfach und scharf (Nachweisgrenze 0,02 g in 12 ml Ethanol). Die Eichkurven sind im Konzentrationsbereich von 0,03–0,3 g in 12 l Ethanol linear. Im Falle des linearen Natriumdodecylbenzolsulfonats werden bei Anwesenheit von nicht-ionischen oberflächenaktiven Substanzen oder von Laurylsulfat in 6fachem Überschuß positiver Fehler von 1–4% erhalten; bei 2–6fachem Überschuß von Haushaltswaschmitteln ergeben sich positive Fehler von 10–50%.Standard-Wasserproben werden zunächst einer Behandlung mit einem Anionenaustauscher unterzogen, die adsorbierten ABS eluiert und durch HPLC oder nach der Methylenblaumethode analysiert. Wiederfindungsraten liegen bei 92–107%.

     

Application of the photoionization detector for single determinations of hydride forming elements

The application of a photoionization detector in conjunction with a flow-through system is described for the determination of arsenic, antimony, selenium, tellurium, bismuth, tin, sulfide and ammonia. The analytical procedure is based upon a preliminary generation of the hydride compounds, their subsequent transfer to the gas phase and finally their detection in the photoionization detector. Linear calibration curves were obtained over three to four orders of magnitude with the following 3s-detection limits: 4 ng/ml As, 0.3 ng/ml Sb, 0.5 ng/ml Se, 3.0 ng/ml Te, 0.1 g/ml Bi, 0.5 g/ml Sn, 10.0 ng/ml S^2–, 0.5 g/ml NH₃.     

Determination of oxygen by deuteron-induced PIPPS

Using the 871-keV¹⁶O p/1,0/ prompt -ray, oxygen was determined with a relative precision of ±3.8% at a concentration level of 120 g g^–1. The sensitivity of the method is below 10 g g^–1. 50 nm oxide layers on silicon wafers can be determined with a relative precision of 10%. A chamber for transporting targets sensitive to atmospheric gases and humidity is described.     

Photometric determination of molybdenum in iron and steels using tin(II) chloride in nonaqueous solvent

Summary A new procedure is proposed for the photometric determination of molybdenum in iron and steels using thiocyanate and tin(II) chloride solution [in glycerol-ethannol (31) or in diethylenglycol] as a reducer and extraction with n-butyl acetate. Beer's law is obeyed between 0.2 and 80 g Mo/ml. The minimum photometric error is 3.2%, the molar absorptivity is 15640 at 470 nm and the best concentration range for determination is between 0.6 and 6 g Mo/ml.

---

Photometrische Bestimmung von Molybdän in Eisen und Stahl mit Hilfe von Zinn(II)-chlorid in nichtwärigem Medium

Zusammenfassung Das vorgeschlagene Verfahren beruht auf Bildung des Thiocyanatkomplexes unter Verwendung von Zinn(II)-chlorid als Reduktionsmittel [in Glycerin/Äthanol (31) oder Diäthylenglykol]. Als Extraktionsmittel dient n-Butylacetat. Das Beersche Gesetz wird im Bereich 0,2–80 g Mo/l befolgt. Der kleinste photometrische Fehler beträgt 3,2%, die molare Extinktion 15640 bei 470 nm und der optimale Konzentrationsbereich 0,6–6 gMo/l.

Lecture presented at Euroanalysis I Conference, 28. 8. –1. 9. 1972 in Heidelberg, Germany.     

Nuclear interferences of uranium and thorium in a reactor neutron activation analysis determination of cerium using the radionuclides141Ce and143Ce

The interference contributions of uranium and thorium to the determination of cerium based on radionuclides¹⁴¹Ce and¹⁴³Ce produced by irradiation in a reactor core was determined. The values of the interference contributions for¹⁴¹Ce were 0.28±0.01 g Ce/g U and /2.01±0.05/x10^–3 g Ce/g Th, and for¹⁴³Ce 1.33±0.03 g Ce/g U and /9.0±0.2/x10^–3 g Ce/g Th.     

Platinum concentration in silicone breast implant material and capsular tissue by ICP-MS

Inductively coupled plasma-mass spectrometry (ICP-MS) was used to determine the concentration of platinum (Pt) in silicone breast implant gel (range, 0.26–48.90 g g^–1 Pt; n=15), elastomer (range, 3.05–28.78 g g^–1 Pt; n=7), double lumen (range, 5.79–125.27 g g^–1 Pt; n=7), foam (range, 5.79–8.36 g g^–1 Pt; n=2), and capsular tissue (range, 0.003–0.272 g g^–1 Pt; n=15). The results show that very high levels of Pt are present in the encasing elastomer, double lumen, and foam envelope materials. Silicone breast implants can be a source of significant Pt exposure for individuals with these implants.     

Analysis for fungicides in paint

Summary Simple methods have been developed for the determination of copper and 8-hydroxyquinoline in paint films. Copper is separated from 8-hydroxy-quinoline by precipitation as copper sulphide and is determined photometrically either by means of diphenylcarbazone (0.1–1g Cu/ml) or benzoin oxime (1 to 10 g Cu/ml). 8-Hydroxyquinoline is determined by measuring the optical density in the ultraviolet region.

---

Zusammenfassung Einfache Verfahren zur Bestimmung von Kupfer und 8-Hydroxychinolin in Anstrichfilmen werden beschrieben. Kupfer wird als Sulfid abgetrennt und photometrisch mit Diphenylcarbazon (0,1–1g Cu/ml) oder Benzoinoxim (1–10g Cu/ml) bestimmt. 8-Hydroxychinolin wird durch Messung der UV-Absorption bestimmt.

---

---

Part III: Hoffmann, E., A. Saracz, and B. Bursztyn: Z. analyt. Chem. 208, 431 (1965).     

Determination of tetraethyllead and tetramethyllead using high performance liquid chromatography and electrochemical detection

Summary A new method for the separation of tetramethyllead (TML) and tetraethyllead (TEL) was developed using high-performance liquid chromatography. The electrochemical detection was examined with different electrodes. Amperometric and pulse-amperometric techniques were investigated and the optimal working potential for each electrode was determined. Linearity for the glassy carbon electrode was observed between 350 ng and 30 g; the detection limit is 310 ng (TML) resp. 340 ng (TEL). In case of the mercury gold electrode the linearity range was 300 g–3 g and the detection limit 1.5 m (TML) resp. 1.7 g (TEL).     

A new spot test reagent for chromium(VI), vanadium(V), and hexacyanoferrate(III) ions: the schiff base from 4,4′-methylenedianiline and 4-dimethylaminobenzaldehyde

Summary A new Schiff base, bis(4-dimethylaminobenzylidine)4,4-methylenedianiline (I) has been prepared by reacting 4-dimethylaminoben-zaldehyde with 4,4-methylenedianiline. A 1% solution ofI in conc. sulphuric acid gives a deep red or blood red colour with Cr(VI), and V(V), and a deep rose red colour with [Fe(CN)₆]^3-. The limits of detection and dilution are 0.7 g, 171,000 for Cr(VI); 5 g, 110,000 for V(V); and 7 g, 17,100 for [Fe(CN)₆]^3-. Cr(III), V(IV), and [Fe(CN)₆]^4- do not interfere. The effects of common anions and cations are reported.

---

Zusammenfassung Durch Umsetzung von 4-Dimethylaminobenzaldehyd mit 4,4-Methylen-dianilin wurde eine neue Schiffsche Base hergestellt, deren 1%ige Lösung in konz. Schwefelsäure eine tiefrote oder blutrote Farbe mit Cr(VI) und V(V), eine tiefrosa Farbe mit [Fe(CN)₆]^3– gibt. Die Nachweisgrenzen bzw. die Grenzkonzentrationen betragen: 0,7 g, 171000 für Cr(VI), 5 g, 110000 für V(V) und 7 g, 17100 für [Fe(CN)]₆ ^3–. Cr(III), V(IV) und [Fe(CN)₆]^4– stören nicht. Der Einfluß gängiger Anionen und Kationen wird angegeben.