Porous properties of activated carbons from waste newspaper prepared by chemical and physical activation

Activated carbons were prepared from old newspaper and paper prepared from simulated paper sludge by chemical activation using various alkali carbonates and hydroxides as activating reagents and also by physical activation using steam. In the chemical activation, the influence of oxidation, carbonization, and activation on the porous properties of the resulting activated carbons was investigated. The specific surface areas (S(BET)) of the activated carbons prepared by single-step activation (direct activation without oxidation and carbonization) were higher than those resulting from two-step activation (oxidation-activation and carbonization-activation) and three-step activation (oxidation-carbonization-activation) methods. The S(BET) values were strongly dependent on the activating reagents and the activating conditions, being >1000 m(2)/g using K(2)CO(3), Rb(2)CO(3), Cs(2)CO(3), and KOH as activating reagents but <1000 m(2)/g using Li(2)CO(3), Na(2)CO(3), and NaOH. These differences in S(BET) values are suggested to be related to the ionic radii of the alkalis used as activating reagents. The microstructures of the higher S(BET) samples show a complete loss of fiber shape but those of the lower S(BET) samples maintain the shape. In the physical activation, the porous properties of the activated carbons prepared by the single-step method were examined as a function of the production conditions such as activation temperature, activation time, steam concentration, and flow rate of the carrier gas. The maximum S(BET) and total pore volume (V(P)) were 1086 m(2)/g and 1.01 ml/g, obtained by activation at 850 degrees C for 2 h, flowing 20 mol% of steam in nitrogen gas at 0.5 l/min. A correlation was found between S(BET) and the yield of the product, the maximum S(BET) value corresponding to a product yield of about 10%. This result is suggested to result from competition between pore formation and surface erosion. Compared with chemically activated carbons using K(2)CO(3), the porous properties of the physically activated carbons have lower S(BET) and V(P) values because of the smaller size and lower volume of their micropores. On the other hand, they retain the original fiber shape and the paper sheet morphology after activation.     

Sorption properties of activated carbons obtained from corn cobs by chemical and physical activation

The paper presents results of a study on obtaining activated carbon from common corn cobs and on its use as adsorbent for removal of pollution from liquid and gas phases. The crushed precursor was subjected to pyrolysis at 500 and 800?°C in argon atmosphere and next to physical or chemical activation by CO₂ and KOH respectively. The effect of pyrolysis conditions and activation method on the physicochemical properties of the materials obtained was tested. The sorption properties of the carbonaceous adsorbents obtained were characterized by determination of nitrogen dioxide and hydrogen sulphide sorption from gas stream in dry and wet conditions as well as by iodine and methylene blue removal from aqueous solution. The final products were microporous activated carbons of well-developed surface area varying from 337 to 1213 m²/g and showing diverse acid-base character of the surface. The results obtained in our study have proved that a suitable choice of the activation procedure for corn cobs permits production of cheap adsorbents with high sorption capacity toward toxic gases of acidic character as well as different pollutants from liquid phase.     

Characteristics of activated carbons prepared from pistachio-nut shells by physical activation

Activated carbons were prepared from pistachio-nut shells, which are one type of lignocellulosic material, by a two-step physical method. The effects of the preparation variables on the activated carbon pore structure were studied, followed by the optimization of these operating parameters. It was found that the activation temperature and dwell time are the important parameters that affect the characteristics of the activated carbons obtained. The effects of CO(2) flow rate and heating rate during activation were also studied. Under the experimental conditions used, the optimum conditions to prepare activated carbons with high surface area and pore volume were identified. The microstructure of the activated carbons prepared was examined by scanning electron microscopy while the Fourier transform infrared spectra showed the changes in the surface functional groups produced during the different preparation stages.     

Effect of activation temperature on the textural and chemical properties of potassium hydroxide activated carbon prepared from pistachio-nut shell

The effect of activation temperature on the textural and chemical properties of activated carbons prepared from pistachio-nut shells by potassium hydroxide activation was studied. Relatively high activation temperature was required to develop high porosities. However, too high an activation temperature resulted in the burn-off of the carbon structures and the widening of micropores to meso- and macropores. The microstructures and microcrystallinities of the carbons prepared were examined using a scanning electron microscope and a powder X-ray diffraction analyzer, respectively, while the Fourier transform infrared spectra indicated the changes in the surface functional groups that were formed during the different preparation stages.     

Adsorption of Safranin-T from wastewater using waste materials- activated carbon and activated rice husks

Textile effluents are major industrial polluters because of high color content, about 15% unfixed dyes and salts. The present paper is aimed to investigate and develop cheap adsorption methods for color removal from wastewater using waste materials activated carbon and activated rice husk-as adsorbents. The method was employed for the removal of Safranin-T and the influence of various factors such as adsorbent dose, adsorbate concentration, particle size, temperature, contact time, and pH was studied. The adsorption of the dye over both the adsorbents was found to follow Langmuir and Freundlich adsorption isotherm models. Based on these models, different useful thermodynamic parameters have been evaluated for both the adsorption processes. The adsorption of Safranin-T over activated carbon and activated rice husks follows first-order kinetics and the rate constants for the adsorption processes decrease with increase in temperature.     

Adsorption of methyl orange using activated carbon prepared from lignin by ZnCl2 treatment

Lignocellulosic materials are good and cheap precursors for the production of activated carbon. In this study, activated carbons were prepared from the lignin at different temperatures (200 to 500°C) by ZnCl₂. The effects influencing the surface area of the resulting activated carbon are activation temperature, activation time and impregnation ratio. The optimum condition, are found an impregnation ratio of 2, an activation temperature of 450°C, and an activation time of 2 h. The results showed that the surface area and micropores volume of activated carbon at the experimental conditions are achieved to 587 and 0.23 cm³ g^?1, respectively. The adsorption behavior of methyl orange dye from aqueous solution onto activated lignin was investigated as a function of equilibrium time, pH and concentration. The Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms. A maximum adsorption capacity of 300 mg g^?1 of methyl orange by activated carbon was achieved.     

Adsorption of benzene and ethanol on activated carbon nanofibers prepared by electrospinning

Activated carbon nanofibers (ACNFs) were prepared by electrospinning polyacrylonitrile solutions, and subsequent steam activation process. The ACNFs were characterized by scanning electron microscope, X-ray photoelectron spectroscopy and nitrogen adsorption at 77 K. The adsorption equilibrium data for benzene and ethanol were obtained by using static vapor adsorption system. As-prepared ACNFs demonstrate higher adsorption capacities for volatile organic compounds (VOCs) than activated carbon fibers (ACFs) by virtue of smaller diameter and more available adsorption sites on the surface. The adsorption performance of ACNFs increases with the burn-off, as a result of the increased microporosity. In addition, it is noteworthy that surface chemistry has an important effect on the adsorption of polar VOCs. The ACNF with higher oxygen content has a stronger adsorption tendency for ethanol.     

Porosity and sorption properties of activated carbons prepared from anthracite by steam-air activation

Fundamental aspects of the steam-air activation of anthracite from Donets coal fields were studied. The effect of the flow rate of moistened air on the development of a porous structure and the sorption properties of the adsorbents obtained were examined.     

Preparation and characterization of activated carbon from date stones by physical activation with steam

Activated carbons are produced from wastes of Algerian date stones by pyrolysis and physical activation in the presence of water vapor into a heated fixed-bed reactor. The effect of pyrolysis temperature and activation hold time on textural and chemical surface properties of raw date stones and carbon materials produced are studied. As expected, the percentage yield decreases with increase of activation temperature and hold time. The characterization of carbon materials is performed by scanning electron microscopy (SEM). X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and nitrogen adsorption (BET). Results show the presence of cellulose and hemicellulose in the raw material, and the predominance of carbon and graphite after pyrolysis. Different oxygen-containing functional groups are found in the raw material while aromatic structures are developed after pyrolysis and activation. The best specific surface area (635 m² g⁻¹) and microporous volume (0.716 cm³ g⁻¹) are obtained when the date stones are grinded, pyrolysed at 700 °C under a 100 cm³ min⁻¹ nitrogen flow and then activated under water vapor at 700 °C for 6 h.     

Adsorption properties of iodine-doped activated carbon fiber

Iodine-doped activated carbon fibers (ACFs) were prepared by the iodine immersion method on pitch-based ACF. Then iodine-doped ACFs were heated in argon at 523 K for 4 h and at 673 K for 2 h. The iodine structure of the resultant iodine-doped ACFs was examined using X-ray photoelectron spectroscopy. The micropore structures were determined by N(2) adsorption at 77 K. The surface area and micropore volume of iodine-doped ACFs are less than those of pristine ACFs. However, the pore width does not change with the iodine doping. The effects of iodine doping on adsorption properties of ACFs for H(2)O and NO at 303 K were examined. The iodine doping affected remarkably the adsorptivities of ACFs for H(2)O and NO. In particular, iodine-doped ACFs treated at 673 K show enhanced adsorptivities for H(2)O and NO. This result suggests that iodine molecules doped on the micropores should be charged by heat treatment at 673 K.     

石油焦系活性炭的吸附脱硫

选取独山子石油焦为原料，以物理活化法制得比表面积达500m2/g～900m2/g的活性炭，进行吸附脱硫研究。采用酸氧化法对活性炭孔结构和微观孔径分布进行改性。酸氧化使活性炭表面酸性官能团含量明显增加，增加量约为原来的5倍。活性炭吸附脱硫性能随表面酸性官能团含量的增加而增大。理想的酸化条件是浓硝酸120℃氧化40min。通过静态吸附实验，活性炭吸附脱硫的最佳条件是，温度25℃，压力1.0MPa，静态吸附6h。最佳条件下吸附脱硫可使模型化合物硫的质量分数从137.9×10－6降至3.1×10－6。从活性炭孔径匹配考察可知，平均孔直径在0.8nm～2.1nm的活性炭对模型化合物硫的质量分数降低具有明显效果。     

High-capacity porous carbons prepared by KOH activation of activated carbon for supercapacitors

High-performance supercapacitor electrode materials are prepared from the commercially available activated carbon （AC） through a facile and low-cost chemical activation method. The obtained results show that AC activated by KOH with an alkali/carbon ratio of 6/1 （ACK6） possesses a specific surface area of 3405 m^2/g, a large pore volume of 2.01 cm^3/g, and exhibits the highest initial specific capacitance of 335 F/g at the current density of 0.5 A/g in 6 mol/L KOH, and 85% coloumbic efficiency for 5000 cycles at 20 mV/s.     

Adsorption of Remazol Brilliant Blue R on activated carbon prepared from a pine cone

In this work the activated pine cone was investigated as adsorbent to remove Remazol Brilliant Blue R from aqueous solution. The effects of various experimental parameters such as initial dye concentration, contact time, temperature, adsorbent dose and pH were examined. The adsorption of Remazol Brilliant Blue R from aqueous solution was increased with the increase in initial dye concentration, contact time, temperature, adsorbent dose but decreased with the increase in the pH. The results in this study indicated that the activated pine cone was an attractive candidate for removing Remazol Brilliant Blue R.     

Characteristics of activated carbon prepared from pistachio-nut shell by zinc chloride activation under nitrogen and vacuum conditions

Activated carbons with well-developed pore structures were prepared from pistachio-nut shells by chemical activation using zinc chloride under both nitrogen atmosphere and vacuum conditions. The effects of preparation parameters on the carbon pore structure were studied in order to optimize these parameters. It was found that under vacuum conditions, the characteristics of the activated carbons produced are better than those under nitrogen atmosphere. The impregnation ratio, the activation temperature, and the activation hold time are the important parameters that influence the characteristics of the activated carbons. The optimum experimental conditions for preparing predominantly microporous activated carbons with high pore surface area and micropore volume are an impregnation ratio of 0.75, an activation temperature of 400 degrees C, and a hold time of 1 h. Under these conditions, the BET surface areas of the carbons activated under nitrogen atmosphere and vacuum conditions were 1635.37 and 1647.16 m2/g, respectively. However, at a ZnCl2 impregnation ratio of 1.5, a furnace temperature of 500 degrees C, and a hold time of 2 h, the predominantly mesoporous activated carbon prepared under vacuum condition had a BET surface area of 2527 m2/g. Fourier transform infrared spectra were used to detect changes in the surface functional groups of the samples during the different preparation stages.     

Texture and adsorptive properties of microporous amorphous carbon materials prepared by the chemical activation of carbonized high-ash biomass

Samples of microporous amorphous carbon materials with calculated BET specific surface areas of up to 3500 m²/g, pore volumes of up to 3.0 cm³/g, and micropore volumes of up to 1.9 cm³/g were prepared using the chemical activation of rice hulls carbonized in a fluidized-bed reactor with a copper-chromium catalyst for deep oxidation. The effects of various activation parameters (temperature, activating agents, etc.) were studied, and optimum parameters were chosen. The resulting materials exhibited sorption capacities of up to 6.3 and 41 wt % for hydrogen at liquid nitrogen temperature and 50 atm and for methane at 0°C and 60 atm, respectively. Because of this, they are promising for use in the purification, storage, and transportation of fuel gases. Moreover, some aspects of the mechanism of the interaction of an activating agent with a carbon-containing precursor are proposed.     

Structural and adsorptive properties of activated carbons prepared by carbonization and activation of resins

Four activated carbons (S1-S4) possessing different structural characteristics were prepared by carbonization of commercial resins (used for ion exchange) and subsequent activation. Their textural parameters were determined on the basis of nitrogen adsorption-desorption at 77.4 K, analyzed by applying several local and overall adsorption isotherm equations. The nature of carbon surface functionalities was analyzed by FTIR spectroscopy. The GC and solid-phase extraction (SPE) techniques were applied to study the influence of the texture of carbonaceous materials on their adsorptive properties. The adsorption efficiency of synthesized carbons with respect to alkylhalides used as probe compounds in the GC measurements varied over a range from 28% (C(2)H(3)Cl(3)/S2) to 85% (CHBr(3)/S1) depending on the type of adsorbates and adsorbents. The concentrating efficiency of these carbons in SPE of explosive materials changed over a larger range from 12% (trinitroglycerin/S4) and 13% (trinitrotoluene/S2) up to 100% (octogen/S1). Active carbon prepared using Zerolite 225x8 as a precursor demonstrated better results than other carbons in two types of adsorption with average values of the efficiency of 75.4% for explosives and 60.8% for alkylhalides.     

Preparation of activated carbon from cherry stones by physical activation in air. Influence of the chemical carbonisation with H2SO4

In the preparation of activated carbon (AC) by the method of physical activation, the carbonisation stage is usually carried out by heat treatment of a precursor at a given temperature in an inert atmosphere, whereas the activation stage is performed in air, carbon dioxide or steam atmosphere. Here, the use of a chemical carbonisation-based method with H₂SO₄ in aqueous solution as an alternative to the physical carbonisation method is studied. Using cherry stones (CS), AC was prepared by physical activation in air, as usual, and by carbonising with H₂SO₄ prior to activating in air. CS was carbonised at 600 °C in nitrogen atmosphere or with H₂SO₄ solutions of various concentrations and the resulting products were activated at 350–550 °C in air. Characterisation was undertaken by proximate analysis, TG–DTG analysis, N₂ adsorption at −196 °C, mercury porosimetry, density measurements and FT-IR spectroscopy. By the H₂SO₄-chemical carbonisation, AC with a lower inorganic matter content, wider pore size distribution in the meso- and macropore ranges, higher mesopore volume and carboxylic acid groups are prepared. The development of microporosity is similar regardless of the carbonisation method provided that the activation of the chemically carbonised product is effected at higher temperature. Physical carbonisation results in AC with an homogeneous macroporosity and with quinone type functional groups. Yield is also slightly higher by this carbonisation method.     

Adsorption of some toxic elements from water samples on modified activated carbon,activated carbon and red soil using neutron activation analysis

A simple and sensitive method for the determination of some metalloids and heavy metals in water samples is presented. The method is based on the preconcentration of the attachment of chelating functionalities with metalloids and toxic metals irreversibly and targeted towards toxic metals adsorbed on modified activated carbon, activated carbon and red soil particles at pH 3.0–9.0±0.2, followed by quantitative determination using instrumental neutron activation analysis (INAA), on the absorbers. Attachment results from attraction that may be physical, chemical, electrical, or a combination of all three. The efficient removal of metalloids and toxic metals, especially arsenic, chromium and mercury is anticipated. The adsorption capacity of the chemically modified activated carbon materials was evaluated for the above mentioned metalloid and toxic metal ions in the presence of iron ions and simulated water samples. Red soil particles containing iron was utilized in the control of oxidation-reduction reaction with metalloids and toxic metals. The preconcentration of the elements of interest on red soil particles, activated carbon and modified activated carbon at different depths, pH and oxidation states was investigated. The results obtained showed good agreement with certified values giving relative errors of less than 10%.     

Adsorption of Cu(II) ions from aqueous solution by hazelnut husk activated carbon prepared with potassium acetate

Hazelnut husk (HH), an agricultural waste, was converted to carbonaceous material by chemical activation using potassium acetate. The produced activated carbon (KAHHAC) was characterized by FTIR, SEM, N₂ adsorption–desorption experiments, CHN elemental analysis, and determination of moisture, ash, and point of zero charge. KAHHAC was used for the batch adsorption of Cu(II) ions from aqueous solutions. Optimum pH and contact time were found to be 5.0 and 240 minutes, respectively. The adsorption equilibrium data were described well by the Langmuir equation providing 105.3?mg?g^?1 Cu(II) adsorption capacity. The pseudo-second-order model successfully described the kinetic of Cu(II) adsorption by KAHHAC. The adsorbed Cu(II) onto KAHHAC was completely desorbed by 0.5?M nitric acid. In conclusion, HH activated carbon (AC) produced by the potassium acetate activation method is a very useful and efficient sorbent material for the removal of Cu(II) from aqueous solution.     

Preparation of activated carbon from sawdust by zinc chloride activation

A series of activated carbons were prepared from sawdust by zinc chloride activation in different operation conditions. The effects of operation parameters such as impregnation ratio, activation temperature and time on the adsorption properties of activated carbons were measured and analyzed in order to optimize these operation conditions. The experimental results show that under the experimental circumstances studied, both the yield and the adsorption for iodine and methylene blue of activated carbon can reach a relatively higher value in the chemical activation process with the impregnation ratio of 100% ZnCl₂/sawdust in the activation temperature of 500 °C carbonized for 60–90 minutes which are the optimum activation conditions in making wood activated carbon. The most important operation parameter in chemical activation with zinc chloride was found to be the impregnation ratio.