基于连续正弦速度扫描方式的激光多普勒测振技术

本文针对逐点扫描激光多普勒非接触测振技术只能进行离散空间域振动测试的缺陷,研究了基于连续正弦速度扫描方式的激光多普勒测振新技术,实现了连续空间域的振动测试。并以简支梁为测试对象,进行了实验验证。实验结果表明:应用连续扫描激光多普勒测振技术与扫描激光多普勒测振技术获取的模态振型匹配一致,而且前者在测试时间、测试数据量及空间分辨率上都优于后者。     

An Experimental Evaluation of Two Potential Improvements for 3D Laser Vibrometer Based Operational Modal Analysis

The use of scanning laser doppler vibrometers (SLDV) is common practice in the context with experimental modal analysis. In recent years, commercial 3D SLDV have been developed, where three laser heads simultaneously point to the same measuring point and an input reference signal is used to combine the results of consecutive records. If the input reference signal is replaced by an additional output reference signal, an operational modal analysis (OMA) can be performed. However, in this case the use of single-point measurements may lead to difficulties identifying certain vibrational modes. Two improvements to reduce these issues were developed in this study: the application of pre-estimation multi-setup merging methods and the use of multi-point measurements with post-estimation coordinate transformation. An enhancement for the application of OMA methods is shown in both cases. In this context there are different possibilities to obtain output reference signals: a) from additional accelerometers or vibrometers and b) from the scan heads of the 3D SLDV itself. Their suitability is investigated in terms of data acqusition, modal analysis and multi-setup merging. Additionally, the feasibility of a “no-reference” measurement is shown. The developed methods have been applied to experimental data using the stochastic subspace identification (cov/ref) and three multi-setup merging methods.     

A Projected Finite Element Update Method for Inverse Identification of Material Constitutive Parameters in transversely Isotropic Laminates

In this paper, a novel application of Finite Element Update Method (FEUM) is proposed for the inverse identification of material constitutive parameters in transversely isotropic laminates. Two-dimensional Digital Image Correlation (2D–DIC) is used for full-field measurements which is required for the identification process. Instead of measuring the in-plane displacements, which is a well-known application of 2D–DIC, we seek to measure the pseudo-displacements resulting from out-of-plane (towards camera) deflection of plate under a point load. These pseudo-displacements are basically the perspective projection of the three dimensional displacement fields on the image-plane of the image acquisition system. The cost function in this method is defined in terms of these projections instead of the true displacements – and hence the name Projected Finite Element Update Method (PFEUM). In this article, identification of in-plane elastic moduli of Carbon Fiber Reinforced Plastic (CFRP) plate has been performed using plate bending experiments which show pre-dominantly out-of-plane deflection with little contribution from the in-plane displacements. Identification results are validated by direct experimental measurements of the unknown elastic constants as well as theoretical estimates based on volume ratio of constituents. The results show good conformance between estimated and target values for at least three material parameters namely E₁, E₂ and G₁₂. Effects of experimental noise on parameter estimates has also been evaluated to explain the observed deviation in estimated parameters with current test configuration.     

Modelling of in-plane wave propagation in a plate using spectral element method and Kane–Mindlin theory with application to damage detection

This paper presents results of experimental and numerical analyses of in-plane waves propagating in a 5 mm-thick steel plate in the frequency range of 120–300 kHz. For such a thickness/frequency ratio, extensional waves reveal dispersive character. To model in-plane wave propagation taking into account the thickness-stretch effect, a novel 2D spectral element, based on the Kane–Mindlin theory, was formulated. An application of in-plane waves to damage detection is also discussed. Experimental investigations employing a laser vibrometer demonstrated that the position and length of a defect can precisely be identified by analysing reflected and diffracted waves.     

Dynamic Subsurface Deformation and Strain of Soft Hydrogel Interfaces Using an Embedded Speckle Pattern With 2D Digital Image Correlation

Background

Subsurface mechanisms can greatly affect the mechanical behavior of biological materials, but observation of these mechanisms has remained elusive primarily due to unfavorable optical characteristics. Researchers attempt to overcome these limitations by performing experiments in biological mimics like hydrogels, but measurements are generally restricted due to the spatio-temporal limitations of current methods.

Objective

Utilization of contemporary 3D printing techniques into soft, transparent, aqueous yield-stress materials have opened new avenues of approach to overcoming these roadblocks. By incorporating digital image correlation with such 3D printing techniques, a method is shown here that can acquire full-field deformation of a hydrogel subsurface in real-time.

Methods

Briefly, the method replaces the solvent of a transparent and low polymer concentration yield-stress material with an aqueous hydrogel precursor solution, then a DIC speckle plane is 3D printed into it. This complex is then polymerized using photoinitiation thereby locking the speckle plane in place.

Results

Full-field deformation measurements are made in real-time as the embedded speckle plane (ESP) responds with the bulk to the applied load. Example results of deformation and strain fields associated with indentation, relaxation, and sliding contact experiments are shown.

Conclusions

This method has successfully observed the subsurface mechanical response in the bulk of a hydrogel and has the potential to answer fundamental questions regarding biological material mechanical behaviors.

     

Scanning-Digital Image Correlation for Moving and Temporally Deformed Surfaces in Scanning Imaging Mode

Background

Images from scanning electron microscopes, transmission electron microscopes and atomic force microscopes have been widely used in digital image correlation methods to obtain accurate full-field deformation profiles of tested objects and investigate the object’s deformation mechanism. However, because of the raster-scanning imaging mode used in microscopic observation equipment, the images obtained from these instruments can only be used for quasi-static displacement measurements; otherwise, spurious displacements and strains may be introduced into the deformation results if these scanning microscopic images are used directly in general digital image correlation calculations for moving and temporally deformed surfaces.

Objective

Realizing kinematic parameter and dynamic deformation measurements on a scanning electron microscope platform.

Methods

Establishing a scanning imaging model of moving and temporally deformed objects that contains motion and deformation equations, a scanning equation and an intensity invariance assumption for small deformations. Then proposing a scanning-digital image correlation (S-DIC) method based on combing the characteristics of the scanning imaging mode with digital image correlation.

Results

Quantitatively investigating the effects of the spurious displacements and strains introduced when using scanning images to represent moving and temporally deformed surfaces in the measurement results. Numerical simulations verify that the accuracy of the S-DIC method is 10^?2pix for the displacement, 10^?4 for the strain, 10^?4pix/s for the velocity and 10^?6s^?1 for the strain rate. Experiments also show that the proposed S-DIC method is effective. Conclusions: The results of this work demonstrate the utility of S-DIC on the field of microscopic dynamic measurement.

     

Full-Field Surface 3D Shape and Displacement Measurements Using an Unfocused Plenoptic Camera

Full-field surface 3D shape and displacement measurements using a single commercial unfocused plenoptic camera (Lytro Illum) are reported in this work. Before measurements, the unfocused plenoptic camera is calibrated with two consecutive steps, including lateral calibration and depth calibration. Each raw image of a checkerboard pattern recorded by Lytro Illum is first extracted to an array of sub-aperture images (SAIs), and the center sub-aperture images (CSAIs) at diverse poses are used for lateral calibration to determine intrinsic and extrinsic parameters. The parallax maps between the CSAI and the remaining SAIs at each pose are then determined for depth parameters estimation using depth calibration. Furthermore, a newly developed physical-based depth distortion model is established to correct the serious distortion of the depth field. To realize shape and deformation measurements, the raw images of a test sample with speckle patterns premade on its surface are captured by Lytro Illum and extracted to arrays of SAIs. The parallax maps between the CSAI and the target SAIs are obtained using subset-based digital image correlation. Based on the pre-computed intrinsic and depth parameters and the disparity map, the full-field surface 3D shape and displacement of a test object are finally determined. The effectiveness and accuracy of the proposed approach are evaluated by a set of experiments involving the shape reconstruction of a cylinder, in-plane and out-of-plane displacement measurements of a flat plate and 3D full-field displacement measurements of a cantilever beam. The preliminary results indicate that the proposed method is expected to become a novel approach for full-field surface 3D shape and displacement measurements.     

In-situ Strain Field Measurement and Mechano-electro-chemical Analysis of Graphite Electrodes Via Fluorescence Digital Image Correlation

Background

Mechano-electro-chemical coupling during the ion diffusion process is a core factor to determine the electrochemical performance of electrodes. However, relationship between the mechanics and the electrochemistry has not been clarified by experiments.

Objective

In this work, we conduct an in situ, visual, comprehensive characterization of strain field and Li concentration distribution to further explore the mechano-electro-chemical relationship.

Methods

The digital image correlation characterized by fluorescent speckle and active optical imaging is developed. Combined with electrochromic-based Li concentration detection, the spatiotemporal evolution of in-plane strain and Li concentration of a graphite electrode during the lithiation and delithiation processes are measured and displayed visually via a dual optical path acquisition system.

Results

The visual results show that in-plane strain and Li concentration possess a spatially non-uniform gradient distribution along the radial direction (i.e., diffusion path) with large values outside and small values inside, and that both present obvious temporal segmentation. And mechano-electro-chemical coupling analysis reveals that the in-plane strain is not always linearly related to the concentration and infers that a high strain limits the diffusion and lithiation. The strain–concentration evolution exhibits obvious asymmetric differences between lithiation and delithiation, wherein three equations are fitted to approximately represent the evolution process between in-plane strain and concentration during the lithiation and delithiation processes

Conclusions

This work overcomes the difficulties of fine strain measurements and collaborative concentration characterization during the electrochemical process, and provides an effective experimental method and data support for further exploration of mechano-electro-chemical coupling.

     

Surface Strain Measurements Using a 3D Scanning Laser Vibrometer

Three-dimensional scanning laser vibrometers enable extremely accurate non-contact measurement of the three-dimensional displacements on the surface of structures. This paper looks at the feasibility of using such a scanning laser vibrometer for the non-contact measurement of dynamic strain fields across the surface of a planar structure subjected to in-plane loading. Issues such as laser head alignment and choice of differentiation filter parameters are discussed. Finally, experimental results of two test specimens are presented which clearly demonstrate the significant potential of this new experimental technique as well as highlighting several limitations.     

A Robust Finite Element-based Filter for Digital Image and Volume Correlation Displacement Data

Background

Digital Image and Volume Correlation (DIC and DVC) are non-contact measurement techniques that are used during mechanical testing for quantitative mapping of full-field displacements. The relatively high noise floor of DIC and DVC, which is exasperated when differentiated to obtain strain fields, often requires some form of filtering. Techniques such as median filters or least-squares fitting perform poorly over high displacement gradients, such as the strain localisation near a crack tip, discontinuities across crack flanks or large pores. As such, filtering does not always effectively remove outliers in the displacement field.

Objective

This work proposes a robust finite element-based filter that detects and replaces outliers in the displacement data using a finite element method-based approximation.

Methods

A method is formulated for surface (2D and Stereo DIC) and volumetric (DVC) measurements. Its validity is demonstrated using analytical and experimental displacement data around cracks, obtained from surface and full volume measurements.

Results

It is shown that the displacement data can be filtered in such a way that outliers are identified and replaced. Moreover, data can be smoothed whilst maintaining the nature of the underlying displacement field such as steep displacement gradients or discontinuities.

Conclusions

The method can be used as a post-processing tool for DIC and DVC data and will support the use of the finite element method as an experimental–numerical technique.

     

3D Strain Field Evolution and Failure Mechanisms in Anisotropic Paperboard

Background

Experimental analyses of the 3D strain field evolution during loading allows for better understanding of deformation and failure mechanisms at the meso- and microscale in different materials. In order to understand the auxetic behaviour and delamination process in paperboard materials during tensile deformation, it is essential to study the out-of-plane component of the strain tensor that is, in contrast to previous 2D studies, only achievable in 3D.

Objective

The main objective of this study is to obtain a better understanding of the influence of different out-of-plane structures and in-plane material directions on the deformation and failure mechanisms at the meso- and microscale in paperboard samples.

Methods

X-ray tomography imaging during in-situ uniaxial tensile testing and Digital Volume Correlation analysis was performed to investigate the 3D strain field evolution and microscale mechanical behaviour in two different types of commercial paperboards and in two material directions. The evolution of sample properties such as the spatial variation in sample thickness, solid fraction and fibre orientation distribution were also obtained from the images. A comprehensive analysis of the full strain tensor in paperboards is lacking in previous research, and the influence of material directions and out-of-plane structures on 3D strain field patterns as well as the spatial and temporal quantification of the auxetic behaviour in paperboard are novel contributions.

Results

The results show that volumetric and deviatoric strain, dominated by the out-of-plane normal strain component of the strain tensor, localize in the out-of-plane centre already in the initial linear stress-strain regime. In-plane strain field patterns differ between samples loaded in the Machine Direction (MD) and Cross Direction (CD); in MD, strain localizes in a more well-defined zone close to the notches and the failure occurs abruptly at peak load, resulting in angular fracture paths extending through the stiffer surface planes of the samples. In CD, strain localizes in more horizontal and continuous bands between the notches and at peak load, fractures are not clearly visible at the surfaces of CD-tested samples that appear to fail internally through more well-distributed delamination.

Conclusions

In-plane strain localization preceded a local increase of sample thickness, i.e. the initiation of the delamination process, and at peak load, a dramatic increase in average sample thickening occurred. Different in-plane material directions affected the angles and continuity of the in-plane strain patterns as well as the sample and fracture properties at failure, while the out-of-plane structure affected how the strain fields distributed within the samples.

     

Simultaneous Measurement of Plate Natural Frequencies and Vibration Mode Shapes Using ESPI

The natural frequencies and vibration mode shapes of flat plates are simultaneously measured using ESPI. The method involves measuring the surface shape of a vibrating plate at high frame rate using a modified Michelson interferometer and high-speed camera. The vibration is excited here by impact; white (random) noise could alternatively be used. Fourier analysis of the acquired data gives the natural frequencies and associated mode shapes. The analytical procedure used has the advantage that it simultaneously identifies full-field quantitative images of all vibration modes with frequencies up to half the sampling frequency. In comparison, the ESPI time-averaging and the traditional Chladni methods both require that the plate be excited at each natural frequency to allow separate qualitative measurements of the associated mode shapes. The Instrumented Hammer method and Laser Doppler Vibrometry give quantitative measurements but require sequential sampling of individual points on the test surface to provide full-field results. Example ESPI measurements are presented to illustrate the use and capabilities of the proposed plate natural frequency and mode shape measurement method.     

Drone-Based StereoDIC: System Development,Experimental Validation and Infrastructure Application

Background

Digital Image Correlation (DIC) is widely used for remote and non-destructive structural health evaluation of infrastructure. Current DIC applications are limited to relatively small areas of structures and require the use of stationary stereo vision camera systems that are not easy to transfer and deploy in remote areas.

Objective

The enclosed work describes the development and validation of an Unmanned Aircraft System (UAS, commonly known as drone) with an onboard stereo-vision system capable of acquiring, storing and transmitting images for analysis to obtain full-field, three-dimensional displacement and strain measurements.

Methods

The UAS equipped with a StereoDIC system has been developed and tested in the lab. The drone system, named DroneDIC, autonomously hovers in front of a prestressed railroad tie under pressure and DIC data are collected. A stationary DIC system is used in parallel to collect data for the railroad tie. We compare the data to validate the readings from the DroneDIC system.

Results

We present the analysis of the results obtained by both systems. Our study shows that the results we obtain from the DroneDIC system are similar to the ones gathered from the stationary DIC system.

Conclusions

This work serves as a proof of concept for the successful integration of DIC and drone technologies into the DroneDIC system. DroneDIC combines the high accuracy inspection capabilities of traditional stationary DIC systems with the mobility offered by drone platforms. This is a major step towards autonomous DIC inspection in portions of a structure where access is difficult via conventional methods.

     

EXPERIMENTAL INVESTIGATIONS ON DYNAMIC CHARACTERISTICS OF A MULTILAYER PIEZOELECTRIC STACK ACTUATOR

Multilayer piezoelectric stack actuators are widely used in many industrial applications and the investigation on the dynamic behavior of this element is needed. In this study, two optical interferometric techniques called amplitude-fluctuation electronic speckle pattern interferometry (AF-ESPI) and laser Doppler vibrometer (LDV) are used to experimentally investigate the vibration characteristics of a single-layer piezoelectric disc and a multilayer piezoelectric stack actuator. These two techniques are full-field measurement for AF-ESPI and point-wise displacement measurement for LDV. Because the clear fringe patterns obtained by the AF-ESPI method will be shown only at resonant frequencies, both the resonant frequencies and corresponding vibration mode shapes of the piezoelectric disc and the multilayer piezoelectric stack actuator are obtained simultaneously by the AF-ESPI method. Interferometric fringe patterns for both the in-plane and out-of-plane vibration mode shapes are demonstrated. In addition to the proposed two optical techniques, numerical computations based on a commercially available finite element package are presented for comparison with the experimental results. Good agreement between the measured data by experimental methods and the numerical results predicted by FEM is found in resonant frequencies and mode shapes for the single-layer piezoelectric disc. However, some discrepancies are observed for the results obtained by AF-ESPI and impedance analysis for the multilayer piezoelectric stack actuator. A detailed discussion is made to address important issues of this problem.     

Tikhonov's regularization approach in mode shape curvature analysis applied to damage detection

In this paper an on-going research effort aimed at detecting and localizing damage in plate-like structures by using mode shape curvature based damage detection algorithm is described. The proposed damage index uses exclusively mode shape curvature data from the damaged structure. This method was originally developed for beam-like structures. In this paper, the method is generalized to plate-like structures which are characterized by two-dimensional mode shape curvature. To calculate mode shape curvatures from the measured mode shapes, three approaches are proposed: the first one is the well-known central difference approximation, the other two are classical approaches based on Tikhonov's regularization technique with smoothing functional. The applicability and effectiveness of the proposed damage detection algorithms are demonstrated experimentally on an aluminium plate containing mill-cut damage. The validity of the method is assessed by comparing the identification results of the experimental test case to the results obtained from the simulated test case. The modal frequencies and the corresponding mode shapes of the aluminium plate are obtained via finite element models for numerical simulations and by using a scanning laser vibrometer (SLV) for the experimental study.     

使用单彩色相机的单相机三维数字图像相关方法

介绍了一种基于单个彩色相机的新型全靶面、单相机三维数字图像相关(3D-DIC)方法。借助于设计巧妙的颜色分光光路,被测物体表面图像可以通过两条不同的光路达到相机靶面,采集的标定靶和实验件表面的彩色图像可以分离得到蓝色和红色子图像。通过使用3D-DIC分析标定靶和实验件表面分离后的蓝色和红色子图像,可以获得物体表面的三维形貌和变形。形貌测量、面内和离面平移、以及静动态三维变形实验验证了该单彩色相机3D-DIC方法的有效性和测量精准度。由于可避免双相机同步,且能实现无分辨率损失的全靶面三维形貌和变形测量,本文方法在需要实现瞬态位移和变形测量的爆炸、冲击、振动等领域中具有广阔重要的应用前景。     

A Refined Shear Deformation Theory of Bending of Isotropic Plates*

ABSTRACT

A nonlinear, in-plane displacement assumption is proposed, based on an undetermined variation df/dz of transverse shear strains through the plate thickness. A second-order ordinary differential equation for f(z) and two surface conditions, as well as a set of eighth-order partial differential equations and four associated boundary conditions, are derived from the principle of minimum potential energy. Coupling exists between the partial and ordinary differential equations. In the homogeneous solutions for the former, in addition to an interior solution contribution, there exist two edge-zone solution contributions, one of which induces self-equilibrated (in the thickness direction) boundary stresses. Three examples are calculated using the present theory. The last gives the stress couple and maximum-stress concentration factors at the free edge of a circular hole in a large bent plate. Numerical results for the examples are compared with those given by three-dimensional elasticity theory and several two-dimensional theories. It is found that the present theory can accurately predict nonlinear variations of in-plane stresses through the thickness of a plate.     

Color Stereo-Digital Image Correlation Method Using a Single 3CCD Color Camera

This paper presents a novel color stereo-digital image correlation (stereo-DIC) method using a single 3CCD color camera for full-field shape, motion, and deformation measurements without any sacrifice of the camera sensor spatial resolution. With the aid of a specially designed color separation device using a beam splitter and two optical bandpass filters, images of blue and red colors are simultaneously recorded by the 3CCD camera from two different optical paths. The blue and red channel sub-images extracted from the recorded color images can be analyzed using the regular stereo-DIC algorithm to obtain the full-field three dimensional (3D) information of a test object surface. The effectiveness and accuracy of the proposed technique are demonstrated by a series of real shape, in-plane and out-of-plane translation, and 3D deformation tests.     

Dynamic Tensile Response of a Microwave Damaged Granitic Rock

Background

Understanding the dynamic tensile response of microwave damaged rock is of great significance to promote the development of microwave-assisted hard rock breakage technology. However, most of the current research on this issue is limited to static loading conditions, which is inconsistent with the dynamic stress circumstances encountered in real rock-breaking operations.

Objective

The objective of this work is to investigate the effects of microwave irradiation on the dynamic tensile strength, full-field displacement distribution and average fracture energy of a granitic rock.

Methods

The split Hopkinson pressure bar (SHPB) system combined with digital image correlation (DIC) technique is adopted to conduct the experiments. The overload phenomenon, which refers to the strength over-estimation phenomenon in the Brazilian test, is validated using the conventional strain gauge method. Based on the DIC analysis, a new approach for calculating the average fracture energy is proposed.

Results

Experimental results show that both the apparent and true tensile strengths increase with the loading rate while decreasing with the increase of the irradiation duration; and the true tensile strength after overload correction is lower than the apparent strength. Besides, the overload ratio and fracture energy also show the loading rate and irradiation duration dependency.

Conclusions

Our findings prove clearly that microwave irradiation significantly weakens the dynamic tensile properties of granitic rock.