Differential pulse voltammetric oxidation of polyriboxanthylic acid at the pyrolytic graphite electrode and a method for detection and determination of traces of xanthine and xanthosine-5'- monophosphate in polyxanthylic acid

Poly(X) (polyriboxanthylic acid) gives up to two differential pulse voltammetric oxidation peaks (peaks I and II) at the PGE. Xanthine, which appears to be a trace contaminant of commercial poly(X) samples, exhibits a differential pulse voltammetric oxidation peak at more negative potentials than the peaks of poly(X). Xanthosine-5'-monophosphate also gives up to two differential pulse voltammetric oxidation peaks at the PGE. An analytical method has been developed to determine trace amounts of xanthine and xanthosine-5'-monophosphate in poly(X) samples based on differential pulse voltammetry.     

Voltammetric and impedance studies of inosine-5'-monophosphate and hypoxanthine

The oxidation mechanism and adsorption of inosine 5'-monophosphate and hypoxanthine were investigated in solutions of different pH using voltammetric and impedance methods at glassy carbon electrodes. For both compounds, the pH dependence from differential pulse voltammetry showed that the same number of electrons and protons are involved in the rate-determining step of the electrochemical reaction. In the case of hypoxanthine, it was also possible to study the effect of different concentrations. At high concentrations of hypoxanthine, two oxidation peaks were observed, the first due to hypoxanthine oxidation with formation of oligomers and the second due to hypoxanthine oligomer oxidation, both compounds adsorbing strongly. Impedance measurements corroborated the voltammetric results and enabled the study of the adsorption of hypoxanthine on glassy carbon.     

Determination of Iodide and Idoxuridine at a Glutaraldehyde‐Cross‐Linked Poly‐L‐Lysine Modified Glassy Carbon Electrode

The detection limit (about 0.017 μg mL^?1) for voltammetric determination of iodide (peak at +0.87 V vs. Ag/AgCl at pH 2) at a glutaraldehyde‐cross‐linked poly‐L ‐lysine modified glassy carbon electrode involving oxidation to iodine was found to be several orders of magnitude lower than that for the voltammetric determination on a bare glassy carbon electrode. This method was applied successfully to the determination of iodide in two medicinal formulations. Idoxuridine was determined indirectly at the same electrode by accumulating it first at ?0.8 V vs. Ag/AgCl. At this potential the C? I bond in the adsorbed idoxuridine is reduced giving iodide, which is then determined at the modified electrode. The method was successfully applied to the determination of idoxuridine in a urine sample.     

Copper-modified poly(3,4-ethylenedioxythiophene) layers for selective determination of dopamine in the presence of ascorbic acid: II Role of the characteristics of the metal deposit

The oxidation of ascorbic acid (AA) and dopamine (DA) is studied on non-modified and copper crystal-modified poly(3,4-ethylenedioxythiophene) (PEDOT)-coated electrodes. Both oxidation reactions are studied for different thickness of the polymer layers. For several microns thick PEDOT layers both PEDOT and Cu-modified PEDOT show the largest currents. A stable voltammetric response for AA oxidation is observed together with a linear dependence of the peak currents on concentration in the 0.3 to 6.0 mM range. For DA oxidation, however, a gradual loss of electroactivity is found with increasing number of voltammetric scans and concentration. This problem is overcome by using thinner (<1 μm) polymer layers. In the presence of both AA and DA, the Cu-modified PEDOT-coated electrodes provide better selectivity with respect to DA in comparison to non-modified PEDOT due to partial suppression of the AA oxidation currents. Thin PEDOT layers modified with electrodeposited Cu crystals show a stable and sensitive response for DA oxidation in the micromolar concentration range. A linear dependence of the voltammetric peak currents is found in a wide concentration range (from 6 to about 200 μM) of DA in the presence of a large excess (1 mM concentration) of AA. The sensitivity is 0.013 μA μM^-1.     

Copper-modified poly(3,4-ethylenedioxythiophene) layers for selective determination of dopamine in the presence of ascorbic acid: I. Role of the polymer layer thickness

The oxidation of ascorbic acid (AA) and dopamine (DA) is studied on non-modified and copper crystal-modified poly(3,4-ethylenedioxythiophene) (PEDOT)-coated electrodes. Both oxidation reactions are studied for different thickness of the polymer layers. For several microns thick PEDOT layers both PEDOT and Cu-modified PEDOT show the largest currents. A stable voltammetric response for AA oxidation is observed together with a linear dependence of the peak currents on concentration in the 0.3 to 6.0 mM range. For DA oxidation, however, a gradual loss of electroactivity is found with increasing number of voltammetric scans and concentration. This problem is overcome by using thinner (<1 µm) polymer layers. In the presence of both AA and DA, the Cu-modified PEDOT-coated electrodes provide better selectivity with respect to DA in comparison to non-modified PEDOT due to partial suppression of the AA oxidation currents. Thin PEDOT layers modified with electrodeposited Cu crystals show a stable and sensitive response for DA oxidation in the micromolar concentration range. A linear dependence of the voltammetric peak currents is found in a wide concentration range (from 6 to about 200 µM) of DA in the presence of a large excess (1 mM concentration) of AA. The sensitivity is 0.013 µA?µM^-1.     

Simultaneous determination of uric acid, xanthine and hypoxanthine at poly(pyrocatechol violet)/functionalized multi-walled carbon nanotubes composite film modified electrode

A sensitive and selective electrochemical method was developed for simultaneous determination of uric acid (UA), xanthine (XA) and hypoxanthine (HX) based on a poly (pyrocatechol violet)/carboxyl functionalized multi-walled carbon nanotubes composite film modified electrode. The preparation and basic electrochemical performance of the novel composite film modified glassy carbon electrode were investigated in details. The electrochemical behaviors of UA, XA and HX at the modified electrode were studied by cyclic voltammetry. The results showed that this new electrochemical sensor exhibited excellent electrocatalytic activity towards the oxidation of the three analytes. The mechanism of catalysis was discussed. The anodic peaks of the three species were well defined with lowered oxidation potential and enhanced oxidation peak currents, so the modified electrode was used for simultaneous voltammetric measurement of UA, XA and HX by differential pulse voltammetry. Under the optimum conditions, the detection limits were 0.16 μmol L(-1) for UA, 0.05 μmol L(-1) for XA and 0.20 μmol L(-1) for HX, respectively (S/N of 3). The proposed method has been successfully applied to simultaneous determination of UA, XA and HX in human serum samples.     

Preconcentration and electroanalysis of silver at pt electrode modified with poly(2-aminothiazole)

Conducting poly(2-aminothiazole) (PAT) films were electrodeposited on a platinum disc electrode surface by constant potential electrolysis of 2-aminothiazole (AT) for the stripping voltammetric determination of Ag(I). Ag(I) was preconcentrated on the polymer matrix by dipping the modified Pt electrode (PAT-Pt electrode) into Ag(I)(aq) solution. Effects of the film thickness, reduction potential, pH, preconcentration time, Ag(I) concentration and the interference of some other metal ions on the oxidation peak current of silver were studied. Cu(II) interference observed to be significant for the stripping voltammetric determination of Ag(I). The detection limit was calculated on the basis of signal to noise ratio of 3 as 2 × 10^?7 mol L^?1.     

Electrochemical Determination of Pyrogallol at Conducting Poly(3,4‐ethylenedioxythiophene) Film‐Modified Screen‐Printed Carbon Electrodes

The electrochemical oxidation of pyrogallol at electrogenerated poly(3,4‐ethylenedioxythiophene) (PEDOT) film‐modified screen‐printed carbon electrodes (SPCE) was investigated. The voltammetric peak for the oxidation of pyrogallol in a pH 7 buffer solution at the modified electrode occurred at 0.13 V, much lower than the bare SPCE and preanodized SPCE. The experimental parameters, including electropolymerization conditions, solution pH values and applied potentials were optimized to improve the voltammetric responses. A linear calibration plot, based on flow‐injection amperometry, was obtained for 1–1000 µM pyrogallol, and a slope of 0.030 µA/µM was obtained. The detection limit (S/N=3) was 0.63 µM.     

Extension of the voltammetric theory to inert,permeable thin-film coated rotating disc electrodes: Part II. Behaviour of ferrocene-ferricinium ion and quinone-hydroquinone systems on polymer-coated electrodes

The voltammetric behaviour of ferrocene-ferricinium ion and quinone-hydroquinone systems is investigated on electrochemically thin film polymer coated electrodes. Ferrocene oxidation is studied in 0.1 M NBu₄ ClO₄-nitromethane on rotating disc platinum electrodes coated with poly(2-hydroxymethyl-1,4-phenylene) oxide (I), poly-(2,6-dimethyl-1,4-phenylene) oxide (II), and poly[4-(2-aminoethyl)-1,2-phenylene] oxide (III) films. The quinone-hydroquinone system is investigated in aqueous medium (1 M HClO₄) with (I), (II) and poly-(2-cyano-1,4-phenylene) oxide films. Experimental results are in good agreement with the previously calculated voltammetric curves in steady-state mass transfer conditions. The charge transfer and diffusion parameters on these polymer-coated electrodes are calculated The quinone-hydroquinone system is rendered reversible by coating a platinum electrode with I.     

Electrochemical behavior of natural and biosynthetic polynucleotides at the pyrolytic graphite electrode A new probe for studies of polynucleotide structure and reactions

The electrochemical oxidation of natural and biosynthetic polynucleotides at a pyrolytic graphite electrode (PGE) has been studied under differential pulse voltammetric conditions. Denatured DNA, ribosomal and transfer RNA give two voltammetric peaks. The first (more negative peak, peak G) corresponds to electrochemical oxidation of guanine residues where-as the second, more positive peak (peak A) corresponds to electrochemical oxidation of adenine residues. Native DNA gives rise only to a small peak A, peak G being totally absent. Denatured DNA and its voltammetric oxidation product are both strongly adsorbed at the PGE. Differential pulse voltammetric oxidation of natural and biosynthetic polynucleotides may provide a valuable technique for probing A-T and G-C regions during structural and conformational changes of these molecules and for following their interactions with other solution species.     

A multi-wall carbon nanotubes-dicetyl phosphate electrode for the determination of hypoxanthine in fish.

An enzymeless sensor based on a multi-walled carbon nanotubes-dicetyl phosphate (MWCNT-DCP) film modified vitreous carbon electrode was developed for the determination of hypoxanthine. The MWCNT-DCP film modified electrode showed a remarkable enhancement effect on the oxidation peak current of hypoxanthine. Under the optimized conditions, the oxidation peak current is proportional to the concentration of hypoxanthine over the range from 5.0 x 10(-7) to 2.0 x 10(-4) mol L(-1) with a detection limit (S/N = 3) of 2.0 x 10(-7) mol L(-1). The MWCNT-DCP film modified electrode has been successfully used to detect hypoxanthine in fish samples.     

Poly(diphenylamine-4-sulfonic acid) modified glassy carbon electrode for voltammetric determination of gallic acid in honey and peanut samples

In this study, a sensitive and selective voltammetric method based on poly(diphenylamine-4-sulfonic acid) modified glassy carbon electrode (poly(DPASA)/GCE) was developed for determination of gallic acid. Appearance of an irreversible oxidative peak at both bare GCE and poly(DPASA)/GCE for gallic acid with about three folds current enhancement and much reduced potential at poly(DPASA)/GCE showed catalytic property of the modifier towards oxidation of gallic acid. Under optimized conditions, Adsorptive stripping square wave voltammetric peak current response of the poly(DPASA)/GCE showed linear dependence with gallic acid concentration in the range 5.00 × 10^?7–3.00 × 10^?4 mol L^?1 with limit of detection of 4.35 × 10^?9. Spike recovery results between 94.62 and 99.63, 95.00–99.80 and 97.25–103.20% of gallic acid in honey, raw peanut, and commercial peanut butter samples respectively, interference recovery results with less than 4.11% error in the presence of uric acid and ascorbic acid, lower LOD and relatively wider dynamic range than most of the previously reported methods validated the potential applicability of the method based on poly(DPASA)/GCE for determination of gallic acid real samples including in honey and peanut samples.     

Electrochemical sensor based on f-SWCNT and carboxylic group functionalized PEDOT for the sensitive determination of bisphenol A

A simple,sensitive,and reliable method for the voltammetric determination of bisphenol A(BPA) by using carboxylic group functionalized single-walled carbon nanotubes(f-SWCNT)/carboxylic-functionalized poly(3,4-ethylenedioxythiophene)(PC4) complex modified glassy carbon electrode(GCE) has been successfully developed.The electrochemical behavior of BPA at the surface of the modified electrode is investigated by electrochemical techniques.The cyclic voltammetry results show that the as-prepared electrode exhibits strong catalytic activity toward the oxidation of BPA with a well-defined anodic peak at 0.623 V in PBS(0.1 mol/L,pH 7.0).The surface morphology of the 3D network of composite film is beneficial for the adsorption of analytes.Under the optimized conditions,the oxidation peak current is proportional to BPA concentration in the range between 0.099 and 5.794 μmol/L(R~2 = 0.9989),with a limit of detection of 0.032 μmol/L(S/N = 3).The enhanced performance of the sensor can be attributed to the excellent electrocatalytic property of/-SWCNT and the extraordinary conductivity of PC4.Furthermore,the proposed modified electrode displays high stability and good reproducibility.The good result on the voltammetric determination of BPA also indicates that the asfabricated modified electrode will be a good candidate for the electrochemical determination and analysis of BPA.     

Electrochemical oxidation of underivatized-nucleic acids at highly boron-doped diamond electrodes

Boron-doped diamond (BDD) electrodes have been examined for the electrochemical oxidation of underivatized-nucleic acids in terms of single stranded and double stranded DNA. Cyclic voltammetry and square wave voltammetry have been used to study the oxidation reactions and to detect DNA without derivatization or hydrolysis steps. At the diamond electrode, at least two well-defined voltammetric peaks were observed for both single stranded and double stranded DNA. Diamond electrode is the first material to show a well-defined voltammetric peaks for adenine group oxidation directly in the helix structure of nucleic acid due to its wide potential window. For single stranded DNA, a third peak, related to the pyrimidine group oxidation was also observed. As-deposited diamond film with predominantly hydrogen-terminated surface exhibited superior performance over oxygen-terminated diamond in terms of sensitivity. However, by optimizing the ionic strength, sensitivity of O-terminated films could be improved. Linear calibration results have shown linearity of current with concentration in the range 0.1-8 microg mL(-1) for both guanine and adenine residues at as-deposited BDD. Detection limits (S/N = 3) of 3.7 and 10 ng mL(-1) for adenine and guanine residue in single stranded DNA, respectively, and 5.2 and 10 ng mL(-1) for adenine and guanine residue in double stranded DNA, respectively, were observed. This work shows the promising use of diamond as an electrochemical detector for direct detection of nucleic acids. The results also show the possibility of using the oxidation peak current of adenine group that is more sensitive for the direct detection of nucleicacids.     

银掺杂聚L-酪氨酸修饰电极同时测定多巴胺、肾上腺素和抗坏血酸

用循环伏安法制备银掺杂聚L-酪氨酸修饰玻碳电极,研究了多巴胺、肾上腺素和抗坏血酸在其电极上的电化学行为,建立了同时测定多巴胺、肾上腺素和抗坏血酸的新方法。当3种组分共存时,在磷酸盐缓冲溶液(pH6.0)中,扫描速率为140mV/s,多巴胺和肾上腺素在修饰电极上分别产生还原峰,峰电位分别为0.198和-0.205V,多巴胺和肾上腺素氧化峰重叠,峰电位为0.313V(vs.Ag/AgCl);抗坏血酸产生一个氧化峰,峰电位0.108V(vs.Ag/AgCl)。多巴胺和肾上腺素的ΔEpc=0.403V,抗坏血酸的氧化峰与多巴胺和肾上腺素的ΔEpa=0.205V,用还原峰和氧化峰可同时测定多巴胺、肾上腺素和抗坏血酸,3种组分同时测定的线性范围分别为5.0×10-6～1.0×10-4mol/L,8.0×10-6～1.0×10-4mol/L和3.0×10-5～1.0×10-3mol/L;检出限分别为5.0×10-7,8.0×10-7和5.0×10-6mol/L。本方法用于人尿液中多巴胺、肾上腺素和抗坏血酸的同时测定,结果满意。     

Voltammetric Determination of Uric Acid at a Fullerene‐C60‐Modified Glassy Carbon Electrode

Glassy carbon electrode modified by microcrystals of fullerene‐C₆₀ mediates the voltammetric determination of uric acid (UA) in the presence of ascorbic acid (AA). Interference of AA was overcome owing to the ability of pretreated fullerene‐C₆₀‐modified glassy carbon electrode. Based on its strong catalytic function towards the oxidation of UA and AA, the overlapping voltammetric response of uric acid and ascorbic acid is resolved into two well‐defined voltammetric peaks with lowered oxidation potential and enhanced oxidation currents under conditions of both linear sweep voltammetry (LSV) and Osteryoung square‐wave voltammetry (OSWV). At pH 7.2, a linear calibration graph is obtained for UA in linear sweep voltammetry over the range from 0.5 μM to 700 μM with a correlation coefficient of 0.9904 and a sensitivity of 0.0215 μA μM^?1 . The detection limit (3σ) is 0.2 μM for standard solution. AA in less than four fold excess does not interfere. The sensitivity and detection limit in OSWV were found as 0.0255 μA μM^?1 and 0.12 μM, for standard solution respectively. The presence of physiologically common interferents (i.e. adenine, hypoxanthine and xanthine) negligibly affects the response of UA. The fullerene‐C₆₀‐modified electrode exhibited a stable, selective and sensitive response to uric acid in the presence of interferents.     

Morphology dependent electrocatalytic activity of Au nanoparticles

The electrocatalytic activity of spherical shape Au particles chemically grown on a sol–gel derived 3D silicate network modified conducting surface has been studied using ascorbate as a model. The nanostructured Au particles show morphology dependent electrocatalytic activity towards ascorbate. Unusual voltammetric behavior for ascorbate has been observed. Unlike the polycrystalline Au electrode, the nanostructured electrode shows two well defined voltammetric peaks for ascorbate at 0 and 0.3 V in neutral and alkaline pHs. These voltammetric peaks are assigned for the oxidation of ascorbate to dehydroascorbate (DHA) and the further oxidation of 2,3-diketogluonic acid (DKG), the hydrolyzed product of DHA. The voltammetric peak corresponding to the oxidation of DKG is very sensitive to the supporting electrolyte anions and solution pH. Voltammetric behavior of DHA has been investigated to support the oxidation pathway of ascorbate on the nanostructured electrode. Surface morphology of the particle controls the electrocatalytic activity.     

Voltammetric studies of purine bases and purine nucleosides with copper

Anodic stripping voltammetry with a hanging mercury drop electrode has been used to investigate the interaction of cooper with the purines adenine, hypoxanthine, xanthine and purine nucleosides adenosine, guanosine and inosine at an ionic strength of 0.1 M in KNO₃ and in the pH range 3.5–5.5. In all cases stabilisation of copper(I) occurs suggesting that the oxidation of copper(0) in the presence of excess ligand proceeds in two one-electron steps.Adsorption onto the electrode has been analysed and conditions where this is negligible were chosen for complexation studies. From the shift of the peak potential corresponding to Cu(0)/Cu(I) oxidation with increasing ligand concentration the stoichiometry of the complexes and their formation constants have been determined. The values obtained are discussed in terms of the ligand structure.     

Sensing System Integrating Lanthanum Hydroxide Nanowires with Copper(II) Ion for Uracil and its Application

Abstract

A sensing system for uracil was constituted by using lanthanum hydroxide nanowires (LNW) as a modifier to obtain LNW modified carbon paste electrode (LNW/CPE) and by introducing copper(II) ion into supporting electrolyte to transform electroinactive uracil to electroactive uracil‐Cu(II) complex. The voltammetric behaviors of uracil in the presence of Cu(II) ion at LNW/CPE were investigated. A reduction peak of the uracil‐Cu(II) complex at ?0.18 V was the two‐electron reduction of Cu(II) ion in the uracil‐Cu(II) complex; while a new oxidation peak at 0.22 V was the one‐electron oxidation of the uracil‐Cu(I) complex. Additionally, the voltammetric responses of all the complexes at LNW/CPE were more sensitive than that at carbon and multiwall carbon nanotube paste electrodes, which resulted from both the large surface effect of LNW and the chemical coordination of uracil with La(III) ion in LNW. With the sensitive oxidation peak of the uracil‐Cu(I) complex at LNW/CPE, a linear range of 4.0×10^?9?3.0×10^?8 mol/l for uracil was obtained along with a detection limit of 2.0×10^?10 mol/l. The proposed system was evaluated by the determination of uracil derivatives, anticancer drug 5‐flurouracil, in pharmaceutical preparations.     

Voltammetric Determination of Adrenaline Using a Poly(1‐Methylpyrrole) Modified Glassy Carbon Electrode

A voltammetric method using a poly(1‐methylpyrrole) modified glassy carbon electrode was developed for the quantification of adrenaline. The modified electrode exhibited stable and sensitive current responses towards adrenaline. Compared with a bare GCE, the modified electrode exhibits a remarkable shift of the oxidation potentials of adrenaline in the cathodic direction and a drastic enhancement of the anodic current response. The separation between anodic and cathodic peak potentials (ΔEp) for adrenaline is 30 mV in 0.1 M phosphate buffer solution (PBS) at pH 4.0 at modified glassy carbon electrodes. The linear current response was obtained in the range of 7.5 × 10^?7 to 2.0 × 10^?4 M with a detection limit of 1.68 × 10^?7 M for adrenaline by square wave voltammetry. The poly(1‐methypyrrole)/GCE was also effective to simultaneously determine adrenaline, ascorbic acid and uric acid in a mixture and resolved the overlapping anodic peaks of these three species into three well‐defined voltammetric peaks in cyclic voltammetry. The modified electrode has been successfully applied for the determination of adrenaline in pharmaceuticals. The proposed method showed excellent stability and reproducibility.