Chromium(III) Potentiometric Sensor Based on Para‐Tertiary‐Butyl Calix[4]arene

A new chromium(III) PVC membrane sensor incorporating p‐tertiary‐butyl calix[4]arene as ionophore, potassium tetrakis as additive and dibutyl phthalate (DBP) as plasticizer was constructed. The electrode exhibited an excellent potentiometric response over a wide concentration range of 1.0×10^?7–1.0×10^?1 M with a Nernstian slope of 20±0.5 mV per decade. The detection limit was 5.0×10^?8 M. The electrode showed a better performance over a pH range of 3.0–8.0, and had a short response time of about <15 s.The electrode was successfully applied to potentiometric titration of Cr (III) with EDTA and for direct determination of chromium(III) in waste water.     

Determination of total phthalate esters in wastewaters by differential pulse polarography

A reliable procedure for the determination of total phthalate esters as phthalic acid in environmental samples is based on differential pulse polarography (d.p.p.). The phthalate esters are extracted from the sample water with hexane; concentrated sulphuric acid/hexane partitioning provides effective removal of organic interferences. The individual phthalate esters are hydrolyzed by refluxing with 10 M potassium hydroxide to phthalic acid, which is extracted with ethyl acetate followed by evaporation of the extract. This procedure gives recoveries of 83–90%. The residue is dissolved in 0.1 M acetic acid/0.1 M potassium chloride for d.p.p. The otpimal conditions for polarography are discussed. The calibration graphs are linear over the range 2 × 10^?6–1 × 10^?4 M and the detection limit for phthalic acid is 5 × 10^?7 M. The method was successfully applied to determine total phthalate esters over the range 0.3–30 μg l^?1 in crude and treated wastewaters.     

Modification of poly(vinyl chloride). X. Crosslinking of poly(vinyl chloride) with a soft segment of an elastomer containing thiol groups

To obtain poly(vinyl chloride) (PVC) of excellent toughness, a new method of crosslinking PVC is proposed in which PVC is crosslinked with the soft segment in an elastomer such as liquid Thiokol. The reaction can be accomplished by immersing PVC–Thiokol blends in liquid ammonia at 20–30°C. A similar reaction occurs in aqueous ammonia when hexamethylphosphoramide is used as an activator. Characteristics of the crosslinked PVC thus obtained and of the controls of a similar uncrosslinked composition (PVC–Thiokol LP-8, 100:5 by weight) were as follows: tensile strength, 7.3 and 4.8 kg/mm²; elongation at break, 30 and 2.5%; Young's modulus, 3.5 × 10⁴ and 2.9 × 10⁴ kg/cm²; tensile impact, 88 and 15 kg-cm/cm³, respectively. The crosslinked PVC as plasticized with dioctyl phthalate (DOP) and the control blend (PVC–Thiokol LP-8–DOP, 100:10:10 by weight), respectively, showed tensile strengths of 5.9 and 4.8 kg/mm², elongations at break of 44 and 24%, Young's moduli of 2.5 × 10⁴ and 1.6 × 10⁴ kg/cm², and tensile impact strengths of 62 and 120 kg-cm/cm³. As the crosslinkage through the soft segments increases up to about 5%, the elongation at break, Young's modulus, and tensile impact, in addition to the tensile strength, are improved. This is different from the results so far observed with the crosslinked amorphous polymers and is characteristic of the products of crosslinking through the soft segment. The experimental results are discussed in this paper.     

Uranyl Microsensor: An Asymmetric Potentiometric Membrane Sensor Based on a New Calix[4]arene

The first asymmetric potentiometric UO₂(II) microsensor is introduced. 5,11,17,23-tetra-tertio butyl(25,27),-bis)2-)n-]2-hydroxy-5-dinitridphenilonitrilidine) amino etoxy(26,28)-di hydroxy calix[4]arene (HAECA) was synthesized. It was found that HAECA can be used as an excellent ionophore in construction of UO₂(II) microsensor. The best performance was obtained with a membrane composition containing 20% PVC, 73% dibutyl phthalate, 5% HAECA, and 2% sodium tetraphenyl borate. The proposed microsensor exhibits a Nernstian slope of 28.5 ± 0.3 mV per decade over a wide concentration range of 1.0 ×10^?10–1.0 × 10^?4 M and a detection limit of 6.0 × 10^?11 M. The potentiometric response of the sensor is independent to the pH of the solution in the range of 2.2–3.6.     

Application of a Zeolite-Poly(vinyl chloride) Electrode to Potentiometric Studies of Alkali Metal Ions

Potentiometric electrodes based on the incorporation of zeolite particles into poly(vinyl chloride) (PVC) membranes are described. The electrode characteristics are evaluated regarding the response towards alkali ions. PVC membranes plasticized with dibutyl phthalate and without lipophilic additives (co-exchanger) are used throughout this study. The electrode exhibits a Nernstian response over the alkali metal cation concentration range of 1.0 × 10^?4 to 1.0 × 10^?1 M with a slope of 57.0 ± 0.9 mV per decade of concentration with a working pH range 3.0–9.0 and a fast response time of ≤15 s. The selectivity coefficients for cesium ion as test species with respect to alkaline earth, ammonium, and some heavy metal ions are determined. The proposed zeolite-PVC electrode is applied to the determination of ionic surfactant.     

A Copper(II) Ion‐Selective Potentiometric Sensor Based on N,N′,N″,N′′′‐Tetrakis(2‐pyridylmethyl)‐1,4,8,11‐tetraazacyclotetradecane in PVC Matrix

The simple PVC‐based membrane containing N,N′,N″,N′′′‐tetrakis(2‐pyridylmethyl)‐1,4,8,11‐tetraazacyclotetradecane (tpmc) as an ionophore and dibutyl phthalate as a plasticizer, directly coated on a glassy carbon electrode was examined as a new sensor for Cu²⁺ ions. The potential response was linear within the concentration range of 1.0×10^?1–1.0×10^?6 M with a Nernstian slope of 28.8 mV/decade and detection limit of 7.0×10^?7 M. The electrode was used in aqueous solutions over a wide pH range (1.3–6). The sensor exhibited excellent selectivity for Cu²⁺ ion over a number of cations and was successfully used in its determination in real samples.     

Sequential Injection Lab‐on‐Valve Procedure for the Determination of Amantadine Using Potentiometric Methods

Amantadine potentiometric detectors were developed, evaluated and incorporated in a SIA‐LOV manifold in order to accomplish the control of pharmaceutical formulations and urine. The electrodes incorporate α‐cyclodextrin as ionophore, dibutyl phthalate or 2‐fluorophenyl 2‐nitrophenyl ether as plasticizers and potassium tetrakis[3,5‐bis‐(trifluoromethyl)phenyl]borate (KTFPB) as cationic additive. The slope increased from 61.2 to 63.8 mV decade^?1 and the practical limit of detection from 2.6×10^?6 mol L^?1 to 2.5×10^?5 mol L^?1 when the plasticizer was changed from 2‐fluorophenyl 2‐nitrophenyl ether to dibutyl phthalate. When incorporated in the flow‐manifold the membranes composed by dibutyl phthalate or with 2‐fluorophenyl 2‐nitrophenyl ether presented slopes and a practical limit of detection of 69.8 mV decade^?1 and 1.5×10^?4 mol L^?1 or 73.7 mV decade^?1 and 5.4×10^?5 mol L^?1, respectively. The electrode presented stable responses for over a year, and were highly selective concerning the representative species of the two sample matrices assayed as interferents. Comparison of obtained results with those provided by reference methods and recovery assays, revealed adequate accuracy for control assays.     

Construction and Performance Characterization of Ion‐Selective Electrodes for Potentiometric Determination of Paroxetine Hydrochloride in Pharmaceutical Preparations and Biological Fluids

Three types of ion‐selective electrodes: PVC membrane, modified carbon paste (CPE), and coated graphite electrodes (CGE) have been constructed for determining paroxetine hydrochloride (Prx). The electrodes are based on the ion pair of paroxetine with sodium tetraphenylborate (NaTPB) using dibutyl phthalate as plasticizing solvent. Fast, stable and potentiometric response was obtained over the concentration range of 1.1×10^?5–1×10^?2 mol L^?1 with low detection limit of 6.9×10^?6 mol L^?1 and slope of a 56.7±0.3mV decade^?1 for PVC membrane electrode, the concentration range of 2×10^?5–1×10^?2 mol L^?1 with low detection limit of 1.2×10^?5 mol L^?1 and slope of a 57.7±0.6 mV decade^?1 for CPE, and the concentration range of 2×10^?5–1×10^?2 mol L^?1 with low detection limit of 8.9×10^?6 mol L^?1 and slope of a 56.1±0.1 mV decade^?1 for CGE. The proposed electrodes display good selectivity for paroxetine with respect to a number of common inorganic and organic species. The electrodes were successfully applied to the potentiometric determination of paroxetine hydrochloride in its pure state, its pharmaceutical preparation, human urine and plasma.     

Samarium(III)-PVC-Membrane Sensor Based on Ethoxy-1-ethoxycarbonyl-1,2-dihydroquinoline

Abstract

2-Ethoxy-1-ethoxycarbonyl-1,2-dihydroquinoline (EED) was found to be a suitable neutral ionophore for the preparation of a highly selective samarium (Sm)(III) membrane sensor. Poly vinylchloride (PVC)–based membranes of EED with sodium tetraphenyl borate (NaTPB) as an anionic additive and dibutylphthalate (DBP), nitrobenzene (NB), and acetophenone (AP) as plasticizing solvent mediators were prepared and investigated as Sm(III) sensors. The sensor exhibited a Nernstian response over a concentration range of 1.0 × 10^?6 to 1.0 × 10^?2 M, with a detection limit of 5.0 × 10^?7 M. The best performance was achieved with a membrane composition of 30% PVC, 66% dibutyl phthalate (DBP), 2% EED, and 2% sodium tetraphenyl borate (NaTPB). It has a very short response time, in the whole concentration range (～10s), and can be used for at least 10 weeks. The proposed electrode shows a very good selectivity toward Sm(III) ions over a wide variety of cations, including alkali, alkaline earth, transition-metal, and heavy-metal ions. The sensor was applied to the determination of Sm ions in binary mixtures.     

Ionophore Properties of Schiff Base Compounds as Ion Sensing Molecules for Fabricating Cu(II) Ion-Selective Electrodes

Bis(2-hydroxybenzaldehyde)-1,2-diaminoethane (L^I), bis(2-hydroxybenzaldehyde)-1,3-diaminopropane (L^II) and bis(2-hydroxybenzaldehyde)-4,4'-methylendianiline (L^III) were examined as ionophores for fabrication of polyvinylchloride (PVC) membrane Cu(II) ion-selective potentiometric sensors. The optimum composition (%) for the sensors was: 5 L^I, 30 PVC, 6 sodium tetraphenylborate (NaTPB), 59 ortho-nitrophenyloctyl ether (NPOE); 4 L^II, 30 PVC, 5 NaTPB, 61 dibutyl phthalate; 6 L^III, 30 PVC, 5 NaTPB, 59 NPOE. The linear response range of the electrodes was 5 × 10^–4–0.05 (L^I), 5 × 10^–4–0.1 (L^II) and 1 × 10^–6–0.01 M (L^III), and the corresponding detection limits were 4 × 10^–4, 4 × 10^–4 and 2 × 10^–7 M, respectively. The sensors were showed rapid response time (≈10 s). Their responses were independent on pH in the range 2.5–5.0 (L^I), 3.2–4.7 (L^II) and 4.0–5.0 (L^III). The selectivity of the prepared electrodes towards copper ions over some mono-, di- and trivalent metal ions was evaluated. The sensors were used as indicator electrode in potentiometric titration of copper ions in aqueous solutions.     

Preparation and evaluation of thermally stable nano-structured self-doped polythiophene coating for analysis of phthalate ester trace levels

Nano‐structured self‐doped polythiophene (SPT) electrodeposited in the presence of fluorinated organic acid was applied as a thermally stable conductive polymer‐based solid‐phase microextraction (SPME) fiber candidate. Quantitative determination of trace levels of phthalate esters including dimethyl phthalate (DMP), diethyl phthalate (DEP), dibutyl phthalate (DBP), and diethylhexyl phthalate (DEHP) was carried out using this novel fiber, coupling with gas chromatography‐flame ionization detector (GC‐FID). The SPT coating was proved to be stable at high temperatures (～350°C) with a high extraction capacity and long lifetime (more than 60 times). Improved temperature resistance was obtained by the presence of sulfonated groups in the backbone of polymer. Thermal stability of novel SPT was superior to common polythiophene (synthesized in LiClO₄). The extraction procedure was optimized by means of the Taguchi orthogonal array experimental design with an OA₁₆ (4⁵) matrix including extraction temperature, extraction time, salt concentration, stirring rate, and headspace volume. The good linearity was obtained for most compounds with correlation coefficients (R²) of between 0.993 and 0.995. The detection limits were lower than 0.12 ng/mL for dimethyl phthalate, DEP, dibutyl phthalate, and diethylhexyl phthalate. The method was successfully applied to the analysis of water samples with the recoveries from 90±1 to 107±1%.     

Development of an electrochemical sensor based on Schiff base for Cu(II) determination at nano level in river water and edible materials

Plasticised membranes using 2-[{(2-hydroxyphenyl)imino}methyl]-phenol (L₁) and 2-[{(3-hydroxyphenyl)imino}methyl]-phenol (L₂), have been prepared and investigated as Cu²⁺ ion-selective sensors. Effect of various plasticisers, namely, dibutyl phthalate (DBP), dibutyl sebacate (DBS), benzyl acetate (BA), o-nitrophenyloctylether (o-NPOE) and anion excluders, oleic acid (OA) and sodium tetraphenylborate (NaTPB) was studied and improved performance was observed in several instances. Optimum performance was observed with membranes of (L₁) having composition L₁ : DBS : OA : PVC in the ratio of 6 : 54 : 10 : 30 (w/w, %). The sensor works satisfactorily in the concentration range 3.2 × 10^?8–1.0 × 10^?1 mol L^?1 with a Nernstian slope of 29.5 ± 0.5 mV decade^?1 of a _cu²⁺ . The detection limit of the proposed sensor is 2.0 × 10^?8 mol L^?1 (1.27 ng mL^?1). Wide pH range (3.0–8.5), fast response time (7 s), sufficient (up to 25% v/v) non-aqueous tolerance and adequate shelf life (3 months) indicate the utility of the proposed sensor. The potentiometric selectivity coefficients as determined by matched potential method indicate selective response for Cu²⁺ ions over various interfering ions, and therefore could be successfully used for the determination of copper in edible oils, tomato plant material and river water.     

Sm3+ Potentiometric Membrane Sensor as a Probe for Determination of Some Pharmaceutics

The increase use of ion sensors in the fields of environmental, agricultural, and medical analysis is stimulating analytical chemists to develop new sensors for fast, accurate, reproducible, and selective determination of various ions. In this study a new samarium membrane sensor was constructed and for the first time, it was applied as a probe in indirect determination of hyoscine, homatropine, and tramadol drugs in their pharmaceutical formulation. The proposed membrane sensor was constructed based on a membrane containing 2% sodium tetraphenyl borate (NaTPB) as an anionic additive, 63% dibutyl phthalate (DBP) as solvent mediator, 5% ionophore, and 30% poly(vinyl chloride) (PVC). The proposed Sm(III) electrode exhibits a Nernstian response of 19.35±0.2 mV per decade of samarium concentration, and has a lower detection limit of 1.0×10^?7 M. The linear range of the sensors was 1.0×10^?7–1.0×10^?1 M. It works well in the pH range of 3.0–8.0.     

A New Pentadentate S‐N Schiffs' Base as a Novel Ionophore in Construction of a Novel Gd(III) Membrane Sensor

We found that bis(thiophenal) pyridine‐2,6‐diamine (BPD) can be used as an excellent ion carrier to prepare a gadolinium‐selective PVC‐based membrane sensor. The use of oleic acid (OA) and potassium tetrakis(p‐chlorophenyl borate)(KTKpClPB), as anionic additives, and dibutyl phthalate (DBP), acetophenone (AP) and nitrobenzene (NB), as plasticizing solvent mediators was investigated. The best performance was observed with a membrane having the composition of 30% PVC; 62% BA; 5% BPD; and 3% KTKpClPB. The resulting sensor works well over a relatively wide concentration range (1.0×10^?6–1.0×10^?1 M) with a Nernstian slope of 19.4±0.4 mV per decade of gadolinium activity over a wide pH range (3.5–8.0). The limit of detection of the sensor is 7.0×10^?7 M (ca. 110 ng mL^?1). The proposed electrode shows excellent discriminating ability toward gadolinium ions with regard to common alkali, alkaline earth, transition, heavy metal ions, and specially, lanthanide ions. The proposed sensor was applied as an indicator electrode for titration of gadolinium ions with EDTA.     

Zur Bestimmung von β-Aminocrotonsäureester nach Migration in Lebensmittel

β-Aminocrotonic esters are of great importance as stabilizers for the production of clearly transparent food packaging of PVC. For the purpose of studying the migration into foods a thin-layer Chromatographic and a polarographic method were elaborated. The TLC method consists of the visual comparison of the intensity of the spots after treatment with Fast Blue B salt. The polarographic determination is carried out after nitrosation of the stabilizer. By the TLC method 10^?7 g of ester per spot are still detectable; the concentration which is still determinable by cathode-ray polarography is 5×10^?7 g of ester and by conventional d.c. polarography 5×10^?6g of ester per ml of final solution. After extraction with acetonitrile traces of the stabilizer which are migrated into edible oil are still determinable down to 2 ppm by the methods described.     

Novel Metronidazole Membrane Sensor Based on a 2,6‐(p‐N,N‐Dimethylaminophenyl)‐4‐Phenylthiopyrylium Perchlorate

A novel PVC‐based membrane sensor based on 2,6‐(p‐N,N‐dimethylaminophenyl)‐4‐phenylthiopyrylium perchlorate (DAPP) is described. The electrode exhibits a sub‐Nernstian response to 1‐(beta‐hydroxyethyl)‐2‐methyl‐5‐nitroimidazole (metronidazol) over a relatively wide concentration range (1.0 × 10^?1 to 1.0 × 10^?5 M) with a detection limit of 8.0 × 10^?6 M. The best performance was obtained with the membrane containing 30% poly (vinyl chloride), 50% dibutyl phthalate, 7% DAPP and 13% oleic acid. It has a fast response time (< 30 s) and can be used for at least four weeks without any major deviation. The proposed sensor revealed very good selectivity for metronidazole over a wide variety of common cations, anions and amino acids and could be used in the pH range of 6.0–7.5. It was successfully used for direct determination of metronidazole in an oral synthetic antiprotozoal as an antibacterial agent, in metronidazole tablets, and metronidazole injections and metronidazole gels.     

An investigation into possible sources of phthalate contamination in the environmental analytical laboratory

A study of common laboratory equipment and components was performed in order to identify sources of contamination of phthalates prior to testing environmental samples for such compounds. A screening study revealed significant leaching from laboratory consumables, such as plastic syringes, pipette tips released maximum leachings of 0.36?µg?cm^?2 diethylhexyl phthalate (DEHP) and 0.86?µg?cm^?2 diisononyl phthalate (DINP), plastic filter holders produced maximum leachings of 2.49?µg?cm^?2 dibutyl phthalate (DBP) from polytetrafluoroethylene (PTFE); specifically 0.61?µg?cm^?2 DBP from regenerated cellulose and 5.85?µg?cm^?2 dimethyl phthalate (DMP) from cellulose acetate and Parafilm® leached levels up to 0.50?µg?cm^?2 DEHP. In addition, a high-temperature bake-out process was found necessary to eliminate quite high levels of two phthalates present in a commercial bulking agent for pressurized liquid extraction.     

Migration phenomena of surfactants in polyethylene film

Migration diffusion coefficients of two surfactants (sorbitan laurate, SPAN‐20 and sorbitan palmitate, SPAN‐40) in polyethylene blend are calculated in the desorption process by means of Fourier transform infrared (FT‐IR) spectroscopy technique at 25°C. They are 2.31 and 2.24 × 10⁻¹¹ cm²/s, respectively, which show no significant dependency of molecular weights of the surfactants on diffusion. The composition of LLDPE (linear low‐density polyethylene) and LDPE (low‐density polyethylene) in LLDPE blend is a 7 : 3 ratio, and ethylene acrylic acid (EAA) copolymer is used to verify its role as a migration controller. The key factor affecting the diffusion of the surfactant is suggested to be the segmental mobility by the semicrystalline LLDPE blend. Incorporation of 20 wt% EAA in the LLDPE blend retards the migration rate of the surfactants by reducing the diffusion coefficients to be 9.6 and 7.7 × 10⁻¹² cm²/s and this is believed to be due to the blocking effect of EAA. Although the diffusion coefficient was varied from system to system, the migration kinetics of the surfactants in short times obeys the Fickian behavior if the experimental error is allowed. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1387–1395, 1999     

Barium(II)-PVC Membrane Sensor Based on 4-4′-Methylenediantipyrine as a Neutral Carrier

Abstract

A highly selective and sensitive poly(vinyl chloride) membrane electrode, using 4-4′-Methylenediantipyrine as an ionophore, has been prepared and examined as a Ba²⁺-selective electrode. The influence of the anion excluder (sodium tetraphenyl borate, NaTPB) and the effect of the plasticizers dibutyl phthalate (DBP), nitrobenzene (NB), and benzyl acetate (BA) were studied. The best performance was obtained with the sensor having a membrane composition (w/w) of (MAP, 2.0%), (PVC, 30%), (NB, 66%), (NaTPB, 2.0%) with a wide working concentration range of 1.0 × 10^?6 to 1.0 × 10^?2 M between the pH values of 3.4 and 10.6. Furthermore, a Nernstian slope of 29.7±0.3 mV/decade of activity was demonstrated with a response time of 15 s. The sensor could be used over a period of 2 months with no potential divergence, revealing a good selectivity for a broad variety of cations including alkali, alkaline earth, heavy and transition metals. Regarding the practical applicability of this sensing device, it was successfully applied for the Ba²⁺ ions detection in a lithophone pigment and as an indicator electrode in the potentiometric titration of the under study cations.     

Temperature‐dependent desorption of surfactants in LLDPE blend films

The temperature‐dependent desorption behavior of surfactants in linear low‐density polyethylene (LLDPE) blend films was studied with Fourier transform infrared spectroscopy at 25, 40, and 50 °C. The LLDPE/low‐density polyethylene blend was 70/30. Three different specimens (labeled II, III, and IV) were prepared with various compositions of the surfactant, sorbitan palmitate (SPAN‐40), and the migration controller, poly(ethylene acrylic acid) (EAA). The calculated diffusion coefficients of SPAN‐40 in specimens II, III, and IV at 25, 40, and 50 °C varied from 9.6 × 10⁻¹² to 17.4 × 10⁻¹² cm²/s, from 5.5 × 10⁻¹² to 11.0 × 10⁻¹² cm²/s, and from 3.1 × 10⁻¹² to 5.8 × 10⁻¹² cm²/s, respectively. In addition, the activation energies of specimens II, III, and IV measured between 25 and 50 °C were 18.74, 19.42, and 20.14, respectively. Hence, the desorption rate of the surfactant increased with the temperature and decreased with an addition of EAA, but the activation energy increased with EAA. The diffusion kinetics, analyzed with a plot of the integrated intensity ratio as a function of time, log(I_t/I_∞) versus log t, at 25, 40, and 50 °C obeyed Fickian diffusion behavior. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 218–227, 2001