Degradation of alkylbenzene sulfonate surfactants by pulsed ultrasound

The application of pulsed ultrasound for the degradation of the nonvolatile surfactants sodium 4-octylbenzene sulfonate (OBS) and sodium dodecylbenzenesulfonate (DBS) was investigated at a frequency of 354 kHz. By comparing the degradation rate constants with those of continuous wave (CW) ultrasound, observed pulse enhancements were found to be dependent on the pulse length, pulse ratio, initial concentration, and surface activity of the surfactants. For a pulse length of 100 ms and a pulse ratio of 1:1 (equal on/off times), the degradation rate constant of 1 mM OBS was nearly twice the value for CW. Furthermore, the degradation rate constant for 1 mM DBS increased significantly when sonicated under a pulse length of 100 ms and a pulse on/off ratio of 1:50. However, the degradation rate of 0.1 mM OBS increased by only 30% with a 100 ms pulse length and pulse ratio of 1:1 as compared to CW, indicating concentration dependence. The enhanced degradation of surfactants by pulsed ultrasound was attributed to the accumulation of surfactants on cavitation bubble surfaces. In addition, as compared to shorter pulse intervals, longer pulse intervals enhanced DBS degradation, indicating that DBS, a more surface active compound, accumulated and equilibrated with the bubble interface more slowly.     

Effect of ultrasound frequency on pulsed sonolytic degradation of octylbenzene sulfonic acid

It has been shown that pulsed ultrasound can influence the amount of surfactant that can adsorb to and decompose at the surface of cavitation bubbles. However, the effect of ultrasound frequency on this process has not been considered. The current study investigates the effect of ultrasound frequency on the pulsed sonolytic degradation of octyl benzenesulfonate (OBS). Furthermore, the effect of pulsing and ultrasound frequency on the rate of *OH radical formation was determined. OBS degradation rates were compared to the rates of *OH radical formation. In this way, conclusions were made regarding the relative importance of accumulation of OBS at cavitation bubble surfaces versus sonochemical activity to the sonochemical decomposition of OBS under different conditions of sonolysis. Comparisons of the data in this way indicate that sonolytic degradation of OBS depends on both the sonochemical activity (i.e., *OH yield) and the accumulation of OBS on cavitation bubble surfaces. However, under a certain set of pulsing and ultrasound frequency exposure conditions, enhanced accumulation of OBS at the gas/solution interface of cavitation bubbles is the sole mechanism of enhanced degradation due to pulsing. On the basis of this finding, conclusions on how pulsing at various ultrasound frequencies affects cavitation bubbles were made.     

Effects of pulsed ultrasound on the adsorption of n-alkyl anionic surfactants at the gas/solution interface of cavitation bubbles

Sonolysis of argon-saturated aqueous solutions of the nonvolatile surfactants sodium dodecyl sulfate (SDS) and sodium 1-pentanesulfonate (SPSo) was investigated at three ultrasonic frequencies under both continuous wave (CW) and pulsed ultrasound. Secondary carbon-centered radicals were detected by spin trapping using 3,5-dibromo-4-nitrosobenzenesulfonic acid (DBNBS) and electron paramagnetic resonance (EPR) spectroscopy. Following sonolysis, -*CH- radicals were observed for both surfactants under both sonication modes. Under CW at 354 kHz, the maximum plateau -*CH- radical yield was higher for SPSo than for SDS, indicating that SDS, which is more surface active under equilibrium conditions, accumulates at the gas/solution interface of cavitation bubbles to a lesser degree, compared with the less surface active surfactant, SPSo. However, after sonolysis (354 kHz) under pulsed ultrasound with a pulse length of 100 ms and an interval of 500 ms, the -*CH- radical yield at the plateau concentrations was higher for SDS than for SPSo due to increased amounts of SDS accumulation on the bubble surfaces. In contrast to the findings following sonolysis at 354 kHz, sonolysis of aqueous surfactant solutions at 620 kHz and 803 kHz showed a higher -*CH- radical yield for SDS compared with SPSo under CW but lower -*CH- radical yield with increasing pulsing interval, indicating a frequency dependence on accumulation. Results indicate that pulsing the ultrasonic wave has a significant effect on the relative adsorption ability of n-alkyl surfactants at the gas/solution surface of cavitation bubbles.     

Effect of surfactants on inertial cavitation activity in a pulsed acoustic field

It has previously been reported that the addition of low concentrations of ionic surfactants enhances the steady-state sonoluminescence (SL) intensity relative to water (Ashokkumar; et al. J. Phys. Chem. B 1997, 101, 10845). In the current study, both sonoluminescence and passive cavitation detection (PCD) were used to examine the acoustic cavitation field generated at different acoustic pulse lengths in the presence of an anionic surfactant, sodium dodecyl sulfate (SDS). A decrease in the SL intensity was observed in the presence of low concentrations of SDS and short acoustic pulse lengths. Under these conditions, the inhibition of bubble coalescence by SDS leads to a population of smaller bubbles, which dissolve during the pulse "off time". As the concentration of surfactant was increased at this pulse length, an increase in the acoustic cavitation activity was observed. This increase is partly attributed to enhanced growth rate of the bubbles by rectified diffusion. Conversely, at long pulse lengths acoustic cavitation activity was enhanced at low SDS concentrations as a larger number of the smaller bubbles could survive the pulse "off time". The effect of reduced acoustic shielding and an increase in the "active" bubble population due to electrostatic repulsion between bubbles are also significant in this case. Finally, as the surfactant concentration was increased further, the effect of electrostatic induced impedance shielding or reclustering dominates, resulting in a decrease in the SL intensity.     

全氟壬烯氧基苯磺酸钠与烷基季铵盐的相互作用

通过六氟丙烯三聚体(全氟壬烯)氧基苯磺酸钠(C₉F₁₇OC₆H₄SO₃Na, OBS)与阳离子碳氢表面活性剂C_nNR[C_nH_2n+1N(CH₃)₃Br, C_nNM, n=8, 10和C_nH_2n+1N(CH₂CH₃)₃Br, C_nNE, n=8, 10, 12]复配, 研究了OBS与C_nNR的摩尔比、 C_nNR疏水链长及C_nNR亲水基团大小对此类阴、 阳离子碳氟-碳氢表面活性剂混合体系的临界胶束浓度(cmc)、 最低表面张力(γ_cmc)、 总饱和吸附量(Γ_tm)及极限分子面积(A_min)的影响. 结果表明, 通过与C_nNR复配, OBS的cmc和γ_cmc均大幅下降, 达到了全面增效的结果. 不同摩尔比的OBS-C₈NE混合体系中, 摩尔比为1:1时表面活性最好, cmc和γ_cmc均最小; 偏离等摩尔比时, OBS过量时混合体系的cmc小于C₈NE过量时混合体系的cmc, 但γ_cmc相差不大. 与单体系相比, OBS-C₈NE混合体系的Γ_tm明显增大、 A_min明显变小. OBS与不同疏水链长的C_nNE复配时, cmc的变化规律为C₈NE>C₁₀NE>C₁₂NE, 表明C_nNE疏水链长的增加能降低混合体系的cmc. 通过比较C_nNM和C_nNE(n=8, 10)的表面活性发现, 改变混合体系中C_nNR的亲水基团大小对混合体系的表面活性无明显影响.     

The effect of surface-active solutes on bubble coalescence in the presence of ultrasound

The sonication of an aqueous solution generates cavitation bubbles, which may coalesce and produce larger bubbles. This paper examines the effect of surface-active solutes on such bubble coalescence in an ultrasonic field. A novel capillary system has been designed to measure the change in the total volume resulting from the sonication of aqueous solutions with 515 kHz ultrasound pulses. This volume change reflects the total volume of larger gas bubbles generated by the coalescence of cavitation bubbles during the sonication process. The total volume of bubbles generated is reduced when surface-active solutes are present. We have proposed that this decrease in the total bubble volume results from the inhibition of bubble coalescence brought about by the surface-active solutes. The observed results revealed similarities with bubble coalescence data reported in the literature in the absence of ultrasound. It was found that for uncharged and zwitterionic surface-active solutes, the extent of bubble coalescence is affected by the surface activity of the solutes. The addition of 0.1 M NaCl to such solutes had no effect on the extent of bubble coalescence. Conversely, for charged surface-active solutes, the extent of bubble coalescence appears to be dominated by electrostatic effects. The addition of 0.1 M NaCl to charged surfactant solutions was observed to increase the total bubble volume close to that of the zwitterionic surfactant. This suggests the involvement of electrostatic interactions between cavitation bubbles in the presence of charged surfactants in the solution.     

Wetting effect of aqueous binary mixed solutions of cationic and nonionic surfactants

Wetting of low-energy solid surfaces (polymers, hydrophobized glass) with aqueous solutions of binary mixtures of cationic and nonionic surfactants was investigated at molar fractions of the cationic surfactant of 0.2, 0.5, and 0.8. In a narrow concentration range, the non-additive effect of wetting was observed: wetting of the solid surfaces with solutions of the mixtures is better than that would be expected from the additive behavior of the components. The magnitude of the effect depends on the surface energy of the solid substrate, total surfactant concentration in a mixture, and molar fraction of the cationic component. The wetting effect of surfactant mixtures with respect to low-energy solid surfaces can be predicted using the surface tension isotherms.     

Kinetics and mechanism of the sonolytic conversion of the aqueous perfluorinated surfactants, perfluorooctanoate (PFOA), and perfluorooctane sulfonate (PFOS) into inorganic products

The perfluorinated surfactants perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) are recognized as widespread in the environment as well as recalcitrant toward most conventional water treatment technologies. In this study, acoustic cavitation as driven by high-frequency ultrasound is shown to be effective in the degradation of aqueous solutions of PFOS and PFOA and effective over a wide range of concentrations from 10 nM to 10 muM for a given compound. Sulfur, fluorine, and carbon mass balances indicate that mineralization occurs immediately following the degradation of the initial perfluorinated surfactant. Near complete conversion of PFOS and PFOA to CO, CO2, F-, and SO42- occurs due to pyrolytic reactions at the surface and vapor phase of transiently collapsing cavitation bubbles. The initial PFOS or PFOA pyrolytic degradation occurs at the bubble-water interface and involves the loss of the ionic functional group leading to the formation of the corresponding 1H-fluoroalkane or perfluoroolefin. The fluorochemical intermediates undergo a series of pyrolytic reactions in the bubble vapor leading to C1 fluoro-radicals. Secondary vapor-phase bimolecular reactions coupled with concomitant hydrolysis converts the C1 fluoro-radicals to carbon monoxide, carbon dioxide, and HF, forming a proton and fluoride upon dissolution. Sonochemical half-lives, which are calculated from high-temperature gas-phase kinetics, are consistent with kinetic observations and suggest that mineralization occurs shortly after initial perfluorinated surfactant interfacial pyrolysis.     

有机颜料与表面活性剂DBS混合物的光催化降解

以TiO₂为光催化剂,研究了表面活性剂十二烷基苯磺酸钠(DBS)和有机颜料耐晒大红BBN(BBN)为混合组分的光催化降解,结果表明,pH值、底物的用量对体系的降解有显著影响,在碱性条件下,DBS的降解速率相对较快,而在酸性环境时,颜料的降解较快,在TiO₂等电点时,降解最慢,酸性条件下, TiO₂对BBN和DBS的吸附性比在碱性和中性环境中大,BBN/DBS体系中, DBS增大了BBN的水溶性,但是没有明显提高BBN的降解褪色速度,DBS浓度为0.42 g/L时,颜料降解最快,0.042 g/L时次之,2.1 g/L时最低,在BBN降解过程中DBS自身也被降解,且略有促进作用。     

How the Physicochemical Properties of the Bulk Material Affect the Ablation Crater Profile,Mass Balance,and Bubble Dynamics During Single-Pulse,Nanosecond Laser Ablation in Water

Understanding the key steps that drive the laser-based synthesis of colloids is a prerequisite for learning how to optimize the ablation process in terms of nanoparticle output and functional design of the nanomaterials. Even though many studies focus on cavitation bubble formation using single-pulse ablation conditions, the ablation efficiency and nanoparticle properties are typically investigated under prolonged ablation conditions with repetition rate lasers. Linking single-pulse and multiple-pulse ablation is difficult due to limitations induced by gas formation cross-effects, which occur on longer timescales and depend on the target materials’ oxidation-sensitivity. Therefore, this study investigates the ablation and cavitation bubble dynamics under nanosecond, single laser pulse conditions for six different bulk materials (Au, Ag, Cu, Fe, Ti, and Al). Also, the effective threshold fluences, ablation volumes, and penetration depths are quantified for these materials. The thermal and chemical properties of the corresponding bulk materials not only favor the formation of larger spot sizes but also lead to the highest molar ablation efficiencies for low melting materials such as aluminum. Furthermore, the concept of the cavitation bubble growth linked with the oxidation sensitivity of the ablated material is discussed. With this, evidence is provided that intensive chemical reactions occurring during the very early timescale of ablation are significantly enhanced by the bubble collapse.     

Tunable synergism/antagonism in a mixed nonionic/anionic surfactant layer at the solid/liquid interface

The use of mixed surfactants for modification of solid surfaces is important for many applications, since beneficial synergism often occurs depending on the surfactant type and mixing conditions. Systematical information on the properties of surfactant mixtures at the solid/liquid interface can be helpful for optimizing the interactions between the surfactants and then their corresponding performance. In this work, a nonionic/anionic surfactant combination, n-dodecyl beta-d-maltoside (DM) and sodium dodecyl sulfonate (SDS), was selected for the study of adsorption on an oxide solid, alumina. Interestingly, the mixture of the two surfactants with opposite pH-dependence of adsorption on alumina exhibits some unique synergistic or antagonistic features that were found to be tunable in the region of pH 4-10. In addition, the DM/SDS molar ratio in the adsorbed layer was found to decrease with concentration in the saturated region at all the pH and mixing ratios tested. The decrease is attributed to the monomer concentration changes in solution due to the difference in surface activities of the two surfactants. The tunable features of this mixture at the solid/liquid interface provide a way to optimize the properties by changing the mixing conditions. This can be valuable in many applications, such as enhanced oil recovery, flotation, and solubilization.     

正负离子混合表面活性剂双水相界面张力的研究

用旋转滴法测定了正负离子混合表面活性剂形成的双水相界面张力, 研究了双水相界面张力与表面活性剂的分子结构、正负离子表面活性剂的摩尔比、总浓度、外加无机盐及温度的关系. 结果表明, 双水相界面张力在一定正、负离子表面活性剂的摩尔比时属于超低界面张力范围. 观察到三种界面张力曲线类型, 第一类为摩尔比1:1 的两边的两条曲线, 界面张力随过剩表面活性剂组分的比例增加而降低; 第二类为一条跨过摩尔比1:1的马鞍型曲线; 第三类为位于摩尔比1:1的一边的一条马鞍型曲线. 界面张力曲线的类型主要取决于表面活性剂的分子结构, 包括亲水基类型、疏水链长度及对称性.     

Adsorption of ethoxylated cationic surfactants on self-assembled monolayers of alkanethiols on gold using surface plasmon resonance detection

Adsorption of a series of ethoxylated cationic surfactants at model surfaces of alkanethiol self-assembled monolayers was studied by the surface plasmon resonance technique. Model surfaces were tailor-made by choosing alkanethiols or mixtures of alkanethiols with methyl, hydroxyl, carboxyl, and trimethylammonium groups in terminal position. The ethoxylated and quaternized cationic surfactants having from 2 to 18 oxyethylene units, showed a decrease in adsorbed amount with increasing oxyethylene chain length for both hydrophobic and hydrophilic surfaces. On a negatively charged surface, containing carboxylate groups, the surfactant with only two oxyethylene groups adsorbed strongly due to electrostatic attraction and the adsorption increased with increasing amount of surface carboxylate groups. This work shows the usefulness of self-assembled alkanethiols on gold as a tool for performing surfactant adsorption studies on surfaces with variable hydrophobicity and charge.     

五氯苯酚降解的超声诱导

人为或自然因素会导致挥发性或不挥发有毒有机物存在于饮用水中,这一现象 已成为国际上共同关心的问题。从长期对健康状况来说,即使不能辨别饮用水中的 味道和气味,但只要有十亿分之几毫克的有毒有机物存在,就足以使水不能饮用。 所以,废水处理刻不容缓。同废水处理相关的实验方法中,超声作为一种处理方法 ,早有报道,因为超声化学效应主要是空化,空化是自由基,特别是羟基自由基产 生的根源,而痉基自由基是强烈而非特殊的氧化物,它能迅速同水中化合物发生反 应。作者以五氯苯酚为模拟水样,分别用低频（16 kHz）和高频[（800 ± 1） kHz]以及其组合进行超声降解研究。研究表明复频降解效果最好,最差为低频。在 Fenton类试剂存在下,与Fenton类单独降解效果相比,复频则是它的20.93倍,高 频是它的4.9倍,低频与它几乎无变化。实验表明,频率组合对有机污染物的降解 是一条有效途径,但需要更进一步的研究。     

Photooxidative mineralization of microorganisms-produced glycolipid biosurfactants by a titania-mediated advanced oxidation process

The photooxidative mineralizations of two microorganisms-produced glycolipid biosurfactants 4-O-(4′,6′-di-O-acetyl-2′,3′-di-O-alkanoyl-β-d-mannopyranosyl)-d-erythritol (MEL-A) and 1-O-(6′-O-acetyl-2′,3′-di-O-alkanoyl-β-d-mannopyranosyl)-d-erythritol (MEL-B) were examined by monitoring the temporal changes in UV absorption, the time profiles of CO₂ evolution and the changes in interfacial tension occurring by an advanced oxidation process in the presence of a metal-oxide (TiO₂). Features of their mineralization are compared to the photomineralization of the anionic dodecylbenzene sulfonate (DBS) surfactant carried out under otherwise identical conditions. The adsorption of surfactants on the TiO₂ surface and the positions of attack of the photogenerated OH radicals on the surfactants’ structure were assessed by molecular orbital (MO) calculations of partial charges and frontier orbital electron densities, respectively. The photodegradation of DBS was faster than the MELs as also evidenced by surface tension measurements, whereas the photomineralization of the anionic DBS surfactant was definitely slower than that of the MEL biosurfactants due to the hydrophobic alkyl chain in the DBS structure. Possible initial mechanistic stages of the photooxidation of MEL-A and MEL-B are proposed based on experimental data and comparison with MO calculations.     

Counterion binding on mixed anionic/cationic micelles

Measurements of counterion binding in mixtures of surfactant aqueous solutions have been performed to study the structure of the anionic/cationic mixed micelle/solution interface. The mixtures studied were SDS/DDAC and STS/TDPC. The binding of chloride and sodium ions to mixed anionic/cationic micelles was measured using ion-specific electrodes. Counterion binding was found to be strongly dependent on the molar ratio of surfactants present. The mixed micelle/solution interface includes the headgroups of both surfactants and counterions of surfactant in excess. The addition of oppositely charged surfactant caused an increasing dissociation of counterions.     

Wetting of Solids by Aqueous Solutions of Surfactant Binary Mixtures: 1. Wetting of Low-Energy Surfaces

Wetting of low-energy surfaces (polymers, hydrophobized glass) by the aqueous solutions of binary mixtures of nonionic (Triton X-100) and cationic (cetyltrimethylammonium bromide) surfactants at the molar fraction of cationic surfactant = 0.2, 0.5, and 0.8 was studied in the wide concentration range. It was shown that the contact angles of mixed solutions at low-energy surfaces could be predicted on the basis of surface tension isotherms. Concentration ranges of wetting synergism were determined.     

Interfacial tension of the aqueous two-phase systems of cationic-anionic surfactant mixtures

Interfacial tensions of the aqueous two-phase systems formed by cationic-anionic surfactant mixtures were measured using spinning drop method. The effects of surfactant structure, molar ratio of cationic to anionic surfactants, surfactant concentration, salt, and temperature on the interfacial tensions were investigated. It was shown that the values of the interfacial tensions of the aqueous two-phase were in the scale of ultra-low interfacial tensions at certain molar ratios of cationic to anionic surfactants. Three types of interfacial tension curves were observed. The first curve comprised two curves that were located on either side of 1:1 molar ratio, and the interfacial tension decreased with the increase of excessive surfactant components. The second one was a saddle-shaped curve that strode over the 1:1 molar ratio. The third type was a saddle-shaped curve that was located beside the 1:1 molar ratio. The types of interfacial tensions depended on the molecular structure of the surfactants such as the hydrophilic groups and the lengths and symmetry of hydrophobic chains.     

Nonionic ortho ester surfactants as cleavable emulsifiers

Acid labile surfactants containing an ortho ester link are used as emulsifiers for an aliphatic oil, squalane. The emulsions were made in the presence of a cationic polymer, either polyamine or the corresponding hydrophobically modified polyamine. Spontaneous hydrolysis of the surfactant resulted in emulsions stabilized by polymer together with degradation products from the surfactant. The effect of breakdown of the surfactant on the emulsion was evaluated by means of droplet size measurements and kinetic stability. One linear and one branched nonionic ortho ester surfactant with the same number of oxyethylene units were characterized and used for the purpose. The ortho ester surfactants are complex mixtures of components, ranging from very hydrophilic to very hydrophobic species. The chemical shift of the central methine proton in the ortho ester link is extremely sensitive to the substitution pattern and it was possible to identify by (1)H NMR the components that make up the surfactants, as has been reported earlier. The change in emulsion stability, the change in droplet size and the rate of surfactant hydrolysis were studied at acidic pH at room temperature. Both gas chromatography and (1)H NMR were used in order to monitor the surfactant degradation. The presence of a polymer gave a more sluggish breakdown of the surfactants, probably due to hydrophobic shielding by the polymer. There was a good correlation between increase of droplet size and degree of surfactant decomposition.     

Sonochemistry of surfactants in aqueous solutions: an EPR spin-trapping study.

The surfactant properties of solutes play an important role in the sonochemistry and sonoluminescence of aqueous solutions. Recently, it has been shown, for relatively low molecular weight surfactants, that these effects can be correlated with the Gibbs surface excess of the solute. In the present study we investigate whether this correlation is valid for relatively high molecular weight surfactants and the mechanisms of surfactant decomposition during sonolysis. Sonolysis of argon-saturated aqueous solutions of nonvolatile surfactants [n-alkanesulfonates, n-alkyl sulfates, n-alkylammoniopropanesulfonates (APS), and poly(oxyethylenes) (POE)] was investigated by EPR and spin-trapping with 3,5-dibromo-4-nitrosobenzenesulfonate. Secondary carbon radicals (-.CH-), formed by abstraction reactions, were observed for all surfactants that were sonicated. The yield of primary carbon (-.CH(2)) and methyl (.CH(3)) radicals that are formed by pyrolysis is greatest for the zwitterionic (i.e., APS) and nonionic surfactants (i.e., POE). The yield of (-.CH-) radicals was measured following sonolysis of n-alkyl anionic surfactants [sodium pentanesulfonate (SPSo), sodium octanesulfonate (SOSo), sodium octyl sulfate (SOS), and sodium dodecyl sulfate (SDS)]. In the concentration range of 0-0.3 mM, the -.CH- radical yield increases in the order SDS approximately equal to SOS approximately equal to SOSo > SPSo. At higher concentrations, a plateau in the maximum (-.CH-) radical yield is reached for each surfactant, which follows the order SPSo > SOS approximately equal to SOSo > SDS; i.e., the radical scavenging efficiency increases with decreasing n-alkyl chain length. A similar trend was observed for the .CH(3) yield following sonolysis of a homologous series of n-alkyl APS surfactants. The results show that the Gibbs surface excess of certain nonvolatile surfactants does not correlate with the extent of decomposition following sonolysis in aqueous solutions. Instead, the decomposition of surfactants depends on their chemical structure and their ability to equilibrate between the bulk solution and the gas/solution interface of cavitation bubbles.