介孔Ni-β-Mo2C/SBA-16催化剂在CH4/CO2重整制合成气反应中的催化性能

采用等体积浸渍将双金属活性组分负载到介孔分子筛SBA-16上,通过热分解制备了负载型催化剂Ni--Mo2C/SBA-16.N2吸附-脱附、X射线粉末衍射和透射电镜等结果表明,引入活性组分后,样品依然保持原有的有序介孔结构,活性组分高度分散于载体上,没有团聚.在CH4/CO2重整制合成气反应中,Ni--Mo2C/SBA-16催化剂具有较高的CH4和CO2转化率,以及CO和H2选择性,有明显的抗积炭作用.     

反应条件对Ni-CaO-ZrO2催化剂上CH4-CO2重整反应及积炭的影响

用共沉淀法制备了Ni-CaO-ZrO₂催化剂,并将其用于CH₄-CO₂重整反应。考察了反应温度、空速和反应物配比对催化剂性能和积炭的影响。通过热力学计算和实验表征研究发现,反应条件对CH₄-CO₂重整反应结果和积炭有重要的影响。由于高温条件同时有利于CH₄裂解和碳物种的及时消除,升高温度可以提高催化剂的活性和稳定性。增大空速则使CH₄的转化率和消碳反应的速率均降低,导致积炭量增加。同时,反应物配比对催化剂表面的积炭量也有很大影响;稍高的CO₂/CH₄摩尔比有利于抑制CH₄-CO₂重整反应过程中的积炭。     

无模板剂一锅法合成介孔Ni-CaO-ZrO2 催化剂及其在CH4-CO2重整反应中的应用研究

通过无模板剂一锅法制备出一种具有较大比表面积和孔容的介孔Ni-CaO-ZrO₂催化剂,并将其用于CH₄-CO₂重整反应过程。利用N₂吸附-脱附(BET)、SEM、TEM、X射线粉末衍射(XRD)、程序升温还原(H₂-TPR)以及热重(TG)等手段对催化剂进行了表征。结果表明,该催化剂具有较强的金属-载体相互作用,这种强金属-载体相互作用(SMSI)使Ni与载体紧密接触,有利于吸附物种在界面进行快速反应,使催化剂在反应过程中具有较高的反应活性和稳定性。虽然反应后的催化剂表面有一定量的积炭生成,但这些积炭多以丝状碳为主,并不会覆盖催化剂的活性位点。     

大气压等离子体射流重整CH4-CO2制合成气

采用大气压等离子体射流,以CH₄和CO^₂直接作为放电气体进行常压下重整制合成气的实验研究,考察了等离子体射流的放电特征及放电距离、放电功率、原料气配比和流量对反应的影响。结果表明,该等离子体具有放电稳定、均匀的特征。重整反应的主要产物为合成气,只有少量的H₂O和积炭生成。优化的反应条件为放电距离为9mm,CH₄和CO₂的摩尔比为4/6。当原料气流量为1000mL/min,放电功率为88.4W时,CH4和CO₂的最高转化率为分别为94.99%和87.23%。甲烷和二氧化碳的转化率随放电功率的增加而增加,随流量的增加而减少。     

高比表面积有序介孔氧化铝的制备与表征

采用溶胶-凝胶法以非离子表面活性剂PEO-PPO-PEO三嵌段共聚物F127为模板剂, 以异丙醇铝为铝源, 以异丙醇为溶剂, 成功地制备出比表面积为485 m2/g、孔径分布窄(2~20 nm)、孔容在1.2 cm3/g以上和孔道呈蠕虫状且具有一定有序性的介孔氧化铝. 采用BET, TEM, XRD和TG多种测试技术对产物性能进行了表征. 探讨了水铝比、醇水混合溶液的滴加速度、反应时间、水浴温度、陈化温度及陈化时间等条件对合成的有序介孔氧化铝结构的影响.     

面向CH4-CO2重整反应的生物质炭基催化剂载体制备工艺的研究进展

CH₄干重整(DRM)技术能够同时将CH₄和CO₂两种温室气体转化为合成气,以实现温室气体减排及资源化利用,因此,越来越受到研究者的青睐。生物质炭具有高比表面积、发达的孔隙结构、高的热稳定性、优异的耐酸碱性、丰富的碱/碱土金属和含氧官能团含量以及成本低廉等优点,其应用于DRM,可以适用于页岩气、油田伴生气、焦炉煤气和煤层气等不同的重整体系,省去部分废气的脱硫等预处理过程,具有重要的工业应用前景。本工作对用于DRM的生物质炭基催化剂载体的制备工艺进行了总结。综述了不同的炭化工艺及其对生物质炭产量和性质的影响;介绍了生物质炭的理化性质对重整反应的影响及影响理化性质的因素;分析了不同的活化方法对生物质炭基催化剂催化性能的影响;并对影响催化剂稳定性的碳消耗进行了介绍。     

热等离子体与催化剂协同重整CH4-CO2

考察了热等离子体与催化剂协同作用于重整反应过程。实验采用三种不同的模式进行:等离子体单独作用、等离子体与催化剂协同作用、等离子体与催化剂协同作用且部分原料气引入等离子体放电区。结果表明,在模式三下,当原料气的总流量为5 m³/h、CH₄/CO₂物质的量比为4/6、等离子体的输入功率为14.4 kW时,CH₄-CO₂重整过程可获得最佳结果,CH₄转化率为77.00%、CO₂转化率为62.40%、H₂选择性为96.70%、CO选择性为88.60%、反应比能为193 kJ/mol、过程的能量转化率为66.4%,该结果已十分接近CH₄-H₂O(g)重整的技术指标。最佳结果主要得益于模式三下的三种不同的反应路径,放电反应、热化学反应与催化反应。     

介孔Al2O3负载PdO催化甲烷燃烧反应性能

采用浸渍法制备了介孔Al2O3(M-Al2O3)负载PdO催化剂,考察了其催化CH4燃烧反应性能.结果表明,以M-Al2O3为载体的PdO催化剂活性比普通Al2O3载体高得多,这很可能与M-Al2O3的孔道结构对PdO物种的限域作用有关.随着PdO/M-Al2O3催化剂焙烧温度的升高,甲烷催化燃烧活性先增加后降低,其中700oC焙烧的催化剂活性最高,400oC反应时CH4转化率为91%.此时Pd物种主要以PdO颗粒形式高度分散在载体的介孔孔道内,而高温焙烧时,Pd物种主要以Pd和PdO的混合晶相存在.尽管900oC焙烧制得的催化剂上CH4的转化率降低,但TOF值最大,这可能与该催化剂中同时存在金属Pd和PdO有关.     

高比表面积介孔Cr2O3：制备及高效催化氧化去除甲苯

采用Cr(NO₃)₃·9H₂O作金属源,葡萄糖作模板剂,通过葡萄糖辅助固态热分解法制备得到高比表面积的虫孔状介孔Cr₂O₃,采用XRD、TEM、TPR和N₂吸脱附技术表征其物理化学性质,并考察了介孔Cr₂O₃上催化氧化去除甲苯的性能。结果表明,经过500℃灼烧处理的m-Cr-5催化剂比表面积高达162m₂·g^-1,平均孔径为6.2nm,且具有优良的低温还原性和多价态铬物种并存,使其催化氧化去除甲苯的活性最好。     

Ni/γ-Al2O3催化剂上CH4-CO2重整体系中积碳-消碳的研究

用动态热重技术和色谱技术联用以及XRD和TEM等表征手段,研究了Ni/γ-Al     

Ni-Sm_x/SiC催化剂甲烷二氧化碳重整性能研究

用浸渍法制备了不同钐含量的Ni-Sm_x/SiC催化剂,其中,镍的质量分数为9%,氧化钐的质量分数分别为0、2%、3%、4%、5%、7%。采用常压微型固定床反应器考察了不同催化剂在甲烷二氧化碳重整反应中的催化性能,并用BET、ICP、XRD、H2-TPR、TG-DTA、XPS和TEM等技术对反应前后催化剂进行表征。结果表明,加入钐后,重整反应中甲烷和二氧化碳转化率明显提高。当钐含量为5%时,Ni-Sm5/SiC表现出最好的活性和稳定性,而且反应后催化剂表面积炭量最少。其原因是钐的加入提高了活性组分与载体的相互作用,有效减少了表面积炭、提高了催化剂的稳定性。     

Yb_2O_3助剂对Ni/SiC催化剂甲烷二氧化碳重整性能的影响

采用浸渍法制备了Ni/SiC和Ni-Ybx/SiC(x=2%、4%、6%、10%,质量分数)催化剂,在固定床反应装置中考察了催化剂在甲烷二氧化碳重整反应中的性能。利用BET、ICP-AES、XRD、H2-TPR、TG-DTA、XPS和TEM等技术对催化剂进行了表征。实验结果表明,Yb的适宜添加量为4%~6%。在800℃条件下Ni-Yb4/SiC和Ni-Yb6/SiC催化剂具有优异的催化活性和稳定性,在100 h的重整反应中,甲烷和二氧化碳的转化率始终保持在90%以上。Yb2O3助剂能够抑制镍颗粒的生长和减少碳沉积量,因此,Ni-Yb/SiC催化剂在连续反应中表现出稳定的活性。     

Low-temperature utilization of CO2 and CH4 by combining partial oxidation with reforming of methane over Ru-based catalysts

Combination of partial oxidation of methane (POM) with carbon dioxide reforming of methane (CRM) has been studied over Ru-based catalysts at 550 ℃. POM, CRM and combined reaction were performed over 8wt%Ru/γ-Al2O3 and the results show that both POM and CRM contribute to the combined reaction, between which POM plays a more important role. Moreover, the addition of Ce to Ru-based catalyst results in an improvement in the activity and CO selectivity under the adopted reaction conditions. The Ce-doped catalyst was characterized by N2 adsorption-desorption, SEM, XRD, TPR, XPS and in situ DRIFTS. The mechanism has been studied by in situ DRIFTS together with the temperature distribution of catalyst bed. The mechanism of the combined reaction is more complicated and it is the combination of POM and CRM mechanisms in nature. The present paper provides a new catalytic system to activate CH4 and CO2 at a rather low temperature.     

Nd,Ce和La改性对Ni/SBA-15催化剂在CH4/CO2重整反应中性能的影响

以稀土金属Nd,Ce或La的氧化物为助剂,采用β-环糊精浸渍法对Ni/SBA-15催化剂进行了改性,并运用X射线衍射、N₂吸附-脱附、程序升温还原和热重等手段考察了改性的催化剂在CO₂重整CH₄制合成气反应中的催化性能. 结果表明,Nd等稀土金属氧化物的添加对催化剂孔结构和晶相结构等性质影响不大,但可影响NiO的还原; Nd的添加使NiO与载体之间以Ni-Nd-O形式相互作用,促进了活性组分NiO的还原. 其中,Nd的添加量为5-10 wt%时所制备的催化剂在重整反应中的催化活性最高,且具有很强的抗积碳性能. La和Ce氧化物促进的Ni催化剂也表现出类似的性质和催化性能.     

CO2 reforming of methane over nickel catalysts supported on nanocrystalline MgAl2O4 with high surface area

In this paper dry reforming of methane (DRM) was carried out over nanocrystalline MgAl2O4-supported Ni catalysts with various Ni loadings. Nanocrystalline MgAl2O4 spinel with high specific surface area was synthesized by a co-precipitation method with the addition of pluronic P123 triblock copolymer as surfactant, and employed as catalyst support. The prepared samples were characterized by X-ray diffraction (XRD), N2 adsorption, H2 chemisorption, temperature-programmed reduction (TPR), temperature-programmed oxidation (TPO), temperature- programmed desorption (TPD) and transmission and scanning electron microscopies (TEM, SEM) techniques. The obtained results showed that the catalyst support has a nanocrystalline structure (crystal size: about 5 nm) with a high specific surface area (175 m2 g-1) and a mesoporous structure. Increasing in nickel content decreased the specific surface area and nickel dispersion. The prepared catalysts showed high catalytic activity and stability during the reaction. SEM analysis revealed that whisker type carbon deposited over the spent catalysts and increasing in nickel loading increased the amount of deposited carbon. The nickel catalyst with 7 wt% of nickel showed the highest catalytic activity.     

光辐照驱动CH4-CO2重整中Ni/MgO-Al2O3催化活性吸收体的活性

将等离子体还原法和常规焙烧还原法制备的Ni基催化剂用于制备太阳能催化活性吸收体,在氙灯模拟的太阳光聚光反应系统中,考察了其催化CH4-CO2重整反应活性.结果表明,等离子体还原法制备的Ni/MgO-A12O3催化活性吸收体的低温活性最高,在光辐照平均能流密度为61 kW/m2,空速36 dm3/(g·h),CH4和CO...     

MgO纳米晶负载镍催化剂用于甲烷蒸汽重整反应(英文)

Nanocrystalline MgO with a relatively high surface area and mesoporous structure was synthesized by a surfactant assisted precipitation method for use as the support of nickel catalysts for steam reforming of methane. The samples were characterized by X‐ray diffraction, N2 adsorption, temperature‐programmed reduction, temperature‐programmed oxidation, scanning electron microscopy, and transmission electron microscopy. The catalysts showed high catalytic activity and good stability in the steam reforming of methane. Increasing the nickel loading up to 10 wt% gave increased activity. Catalysts with higher nickel loadings showed more deposited carbon after reaction. The excellent anti‐coking performance of the catalysts was attributed to the formation of a nickel‐magnesia solid solution, basicity of the support surface, and nickel‐support interaction.     

铝源对Ni/Al2 O3催化剂结构及其CO2-CH4重整性能的影响

以三种不同铝源采用溶液燃烧法制备了系列Ni/Al_2O_3催化剂,通过XRD、H_2-TPR、NH_3-TPD、N_2吸附-脱附、TGDTG和TPH等分析方法对反应前后催化剂进行了表征,研究了铝源对Ni/Al_2O_3催化剂结构、表面性质及其CO_2-CH_4重整性能的影响。结果表明,以Al(NO_3)_3·9H_2O为铝源制备的NiNO-AlNO催化剂比表面积较大,达102 m~2/g;高温还原峰面积大,峰型更为弥散;且载体Al_2_O_3具有一定的结晶性。而以Al_2(SO_4)_3·18H_2O和AlCl_3·6H_2O为铝源制备的NiNO-AlSO和NiNO-AlCl催化剂,其载体以无定型Al_2O_3存在,活性组分Ni晶粒粒径大、分散性差,还原峰面积较小,与载体的相互作用较弱。其中,由于硫酸铝较为稳定,需要在更高温度下才能转化为Al_2O_3,且所制备NiNO-AlSO催化剂中残留有含硫物质,使得其表面酸性较强。评价结果显示,NiNO-AlNO催化剂活性较高,稳定性好,CH4转化率为31.21%,CO_2转化率为48.97%。积炭分析结果发现,NiNO-AlNO催化剂表面积炭量最少,沉积炭主要以无定型态存在,具有良好的抗积炭性能。     

Ni/MgO catalyst prepared using atmospheric high-frequency discharge plasma for CO2 reforming of methane

A new type of Ni/MgO catalyst was prepared using atmospheric high-frequency discharge cold plasma. The influences of conventional method, plasma method, and plasma plus calcination method on the catalytic activity were studied and the CO2 reforming of methane was chosen as the probe reaction. The catalysts were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), X-ray photoelectron spectroscopy, and CO2 temperature-programmed surface reaction techniques. The results suggested that the nickel-based catalyst prepared by plasma plus calcination method possessed a smaller particle size and a higher dispersion of active component, better low-temperature activity and enhanced anti-coking ability. The conversion of CO2 and CH4 was 90.70% and 89.37%, respectively, and the reaction lasted for 36 h without obvious deactivation under 101.325 kPa and 750°C with CO2/CH4 = 1/1.     

Supported Co catalysts for methane reforming with CO2

Co/-Al₂O₃ catalysts prepared at different calcination temperatures were tried in methane reforming with CO₂ and characterized by XRD, H₂-TPR and coking reaction via CH₄ temperature-programmed decomposition. Characterizations indicated that the surface species of Co, reforming activity and coke formation rate strongly depended on calcination temperature and reduction time.This revised version was published online in December 2005 with corrections to the Cover Date.