A novel poly(taurine) modified glassy carbon electrode for the simultaneous determination of epinephrine and dopamine

A novel taurine modified glassy carbon electrode was prepared by electropolymerization method. The electrochemical behaviors of epinephrine (EP) and dopamine (DA) at the modified electrode were studied by cyclic voltammetry. The modified electrode exhibited enhanced sensitivity and excellent electrochemical discrimination to DA and EP. The cathodic peaks of the two species were well-separated with a potential difference of about 390 mV, so the poly(taurine) modified electrode was used for simultaneous voltammetric measurement of EP and DA by differential pulse voltammetry. Under the optimum conditions, the cathodic peak currents were linear to concentrations of EP and DA in the range of 2.0 × 10⁻⁶ to 6.0 × 10⁻⁴ mol L⁻¹ and 1.0 × 10⁻⁶ to 8.0 × 10⁻⁴ mol L⁻¹, respectively. The detection limits for EP and DA were 3.0 × 10⁻⁷ and 1.0 × 10⁻⁷ mol L⁻¹, respectively. Because the oxidation of ascorbic acid (AA) is an irreversible reaction at modified electrode, the interference of AA for determining EP and DA was eliminated. The modified electrode has been satisfactorily used for the simultaneous determination of EP and DA in pharmaceutical injections.     

Voltammetric determination of quercetin at a multi-walled carbon nanotubes paste electrode

Quercetin can effectively accumulate at multi-walled carbon nanotubes-paraffin oil paste electrodes (CNTPE) and cause a sensitive anodic peak at around 0.32 V (vs. SCE) in a 0.10 M phosphate buffer solution (pH = 4.0). Under optimized conditions, the anodic peak current is linear to quercetin concentration in the ranges of 2.0 × 10^− 9−1.0 × 10^− 7 M and 1.0 × 10^− 7−2.0 × 10^− 5 M, and the regression equations are i_p (μA) = 0.0017 + 0.928c (μM, r = 0.999) and i_p (μA) = 0.183 + 0.0731c (μM, r = 0.995), respectively. This paste electrode can be regenerated by repetitively cycling in a blank solution for about 2 min. A 1.0 × 10^− 6 M quercetin solution is measured for 10 times using the same electrode regenerated after every determination, and the relative standard deviation of the peak current is 1.7%. The method has been applied to the determination of quercetin in hydrolysate product of rutin and the recovery is 99.2–102.6%. In comparison with graphite paste electrode, carbon nanotubes-nujol paste electrode and carbon nanotubes casting film modified glassy carbon electrode, the CNTPE gives higher ratio of signal to background current and better defined voltammetric peak.     

A new hydrogen peroxide biosensor based on gold nanoelectrode ensembles/multiwalled carbon nanotubes/chitosan film-modified electrode

Gold nanoelectrode ensembles were produced by electrodeposition using multiwalled carbon nanotubes (MWNTs) as template. A new third generation amperometric biosensor for hydrogen peroxide was developed based on adsorption of horseradish peroxidase (HRP) at the glassy carbon (GC) electrode modified with Au nanoelectrode ensembles/multiwalled carbon nanotubes/chitosan film. The resulting HRP biosensor offered an excellent detection for hydrogen peroxide at −0.11 V with a linear response range of 2.08 × 10⁻⁷ to 7.6 × 10⁻³ M with a correlation coefficient of 0.998, and response time <5 s. The detection limit was 1.02 × 10⁻⁷ M at 3σ. The biosensor displays rapid response, expanded linear response range, and excellent repeatability. The simple and fast fabrication of the sensor makes it superior to other techniques.     

Preparation of L-Cys–Au colloid self-assembled nanoarray electrode based on the microporous aluminium anodic oxide film and its application to the measurement of dopamine

A novel method for fabricating a nanoarray electrode combining the template technique with the self-assembled approach was developed. The glassy carbon electrode was modified with the Au nanoarray using micropores of aluminum anodic film as template. Then, the Au nanoarray electrode was self-assembled with L-cysteine (L-Cys) and gold colloid, respectively. In order to evaluate the electrochemical characteristics of L-Cys–Au colloid self-assembled nanoarray electrode, was chosen as molecule probe and cyclic voltammetry was used. In addition, the functional nanoarray electrode was applied to measuring dopamine (DA). The resulting L-Cys–Au colloid self-assembled nanoarray electrode demonstrated that the linear calibration range extended over three orders of magnitude of DA concentrations (1.0 × 10⁻⁹–1.0 × 10⁻⁶ mol/L) and the detection limit was 5.0 × 10⁻¹⁰ mol/L.     

Palladized aluminum electrode covered by Prussian blue film as an effective transducer for electrocatalytic oxidation and hydrodynamic amperometry of N-acetyl-cysteine and glutathione

The mediated oxidation of N-acetyl cysteine (NAC) and glutathione (GL) at the palladized aluminum electrode modified by Prussian blue film (PB/Pd–Al) is described. The catalytic activity of PB/Pd–Al was explored in terms of Fe^III[Fe^III(CN)₆]/Fe^III[Fe^II(CN)₆]¹⁻ system by taking advantage of the metallic palladium layer inserted between PB film and Al, as an electron-transfer bridge. The best mediated oxidation of NAC and GL on the PB/Pd–Al electrode was achieved in 0.5 M KNO₃ + 0.2 M potassium acetate of pH 2. The mechanism and kinetics of the catalytic oxidation reactions of the both compounds were monitored by cyclic voltammetry and chronoamperometry. The charge transfer-rate limiting step as well as overall oxidation reaction of NAC or GL is found to be a one-electron abstraction. The values of transfer coefficients α, catalytic rate constant k and diffusion coefficient D are 0.5, 3.2 × 10² M⁻¹ s⁻¹ and 2.45 × 10⁻⁵ cm² s⁻¹ for NAC and 0.5, 2.1 × 10² M⁻¹ s⁻¹ and 3.7 × 10⁻⁵ cm² s⁻¹ for GL, respectively. The modifying layers on the Pd–Al substrate have reproducible behavior and a high level of stability in the electrolyte solutions. The modified electrode is exploited for hydrodynamic amperometry of NAC and GL. The amperometric calibration graph is linear in concentration ranges 2 × 10⁻⁶–40 × 10⁻⁶ for NAC and 5 × 10⁻⁷–18 × 10⁻⁶ M for GL and the detection limits are 5.4 × 10⁻⁷ and 4.6 × 10⁻⁷ M, respectively.     

Evaluation of a chloramine-T-selective electrode for catalytic titration of silver and mercury(II) based on iodide-catalyzed chloramine-T reactions

Semiautomatic methods are described for the catalytic titrimetric determination of microamounts of silver and mercury(II) using a chloramine-T-selective electrode as monitor. The methods are based on the inhibitory effect of Ag(I) and Hg(II) on the iodide-catalyzed chloramine-T-arsenite and chloramine-T-H₂O₂ reactions. Microamounts of silver in the range 0.2–200 μg (1 × 10⁻⁷−1 × 10⁻⁴ M) and of mercury(II) in the range 0.1–200 μg (2.5 × 10⁻⁸−5 × 10⁻⁵ M) were determined using the chloramine-T-As(III) indicator reaction. Mercury(II) in the range 4–2000 μg (1 × 10⁻⁶−5 × 10⁻⁴ M) was also determined using the chloramine-T-H₂O₂ indicator reaction. The accuracy and precision were in the range 0.1–1%.     

Electrocatalytic response of dopamine at a dl-homocysteine self-assembled gold electrode

The gold electrode self-assembled with the homocysteine monolayer (Hcy/Au) is demonstrated to catalyze the electrochemical response of dopamine (DA) by cyclic voltammetry. A pair of well-defined redox waves was obtained and the calculated standard rate constant (k_s) is 2.1×10⁻² cm/s at the self-assembled electrode. The reduction peak of DA can be used to determine the concentration of DA in presence of ascorbic acid (AA) owing to the Hcy/Au also catalyzing the electrochemical oxidation of AA.     

Spectrofluorimetric quantification of bromazepam using a highly selective optical probe based on Eu–bromazepam complex in pharmaceutical and serum samples

A rapid, simple and sensitive spectrofluorimetric method for determination of trace amount of bromazepam is developed. In phosphate buffer of pH 7.4. The bromazepam enhance the luminescence intensity of the Eu³⁺ ion in Eu³⁺–bromazepam complex at λ_ex = 390 nm. The produced luminescence intensity of Eu³⁺–bromazepam complex is in proportion to the concentration of bromazepam. The working range for the determination of bromazepam is 2.3 × 10⁻⁸ to 6.2 × 10⁻⁷ M with detection limit (LoD) and quantitative detection limit (LoQ) of 3 × 10⁻⁹ and 1.2 × 10⁻⁸ M, respectively. While, the working range, detection limit (LoD) and quantitative detection limit (LoQ) in case of the quantum yield calculations are 3.7 × 10⁻⁸ to 3.4 × 10⁻⁷ M with of 3.4 × 10⁻⁹ and 9.2 × 10⁻⁸ M, respectively. The enhancement mechanism of the luminescence intensity in the Eu³⁺–bromazepam system has been also explained.     

Indirect kinetic microdetermination of oxalate, citrate, and fluoride ions

An indirect catalytic method for the separate microdetermination of oxalate, citrate, and fluoride ions is described. The method is based on the inhibition action of oxalate, citrate, and fluoride ions on the catalytic oxidation reaction of 2,4-diaminophenol-hydrogen peroxide by iron(III).Procedures for the determination of 1.76 × 10⁻² to 17.6 × 10⁻² μg/ml for oxalate ion, 3.78 × 10⁻² to 30.24 × 10⁻² μg/ml for citrate ion, and 0.38 to 4.18 μg/ml for fluoride ion are given.Quantities of 1.76 × 10⁻² to 17.6 × 10⁻² μg/ml for oxalate ion, 3.78 × 10⁻² to 30.24 × 10⁻² μg/ml for citrate ion, and 0.38 to 4.18 μg/ml for fluoride ion could be determinated with a relative error of about 1–3.5% for oxalate and citrate ions and 1–2% for fluoride ion.     

C60 trianion-mediated electrocatalysis and amperometric sensing of hydrogen peroxide

Heterogeneous electrocatalytic reduction of hydrogen peroxide (H₂O₂) by C₆₀ is reported for the first time. C₆₀ is embedded in tetraoctylammonium bromide (TOAB) film and is characterized by scanning electron microscopy and cyclic voltammetry. Electrocatalytic studies show that the trianion of C₆₀ mediates the electrocatalytic reduction of H₂O₂ in aqueous solution containing 0.1 M KCl. Application of such film modified electrode as an amperometric sensor for H₂O₂ determination is also examined. The sensor shows a fast response within 1 s and a linear response is obtained (R = 0.9986) in the concentration range from 3.33 × 10⁻⁵ to 2.05 × 10⁻³ mol L⁻¹ for H₂O₂, with the detection limit of 2 × 10⁻⁵ mol L⁻¹ and the sensitivity of 1.65 μA mM⁻¹. A good repeatability and stability is shown for the sensor during the experiment.     

Direct electrochemistry of glucose oxidase based on its direct immobilization on carbon ionic liquid electrode and glucose sensing

Direct electrochemistry of glucose oxidase (GOx) has been achieved by its direct immobilization on carbon ionic liquid electrode (CILE) with a conductive hydrophobic ionic liquid, 1-butyl pyridinium hexafluophosphate ([BuPy][PF₆]) as binder for the first time. A pair of reversible peaks is exhibited on GOx/CILE by cyclic voltammetry. The peak-to-peak potential separation (ΔE_P) of immobilized GOx is 0.056 V in 0.067 M phosphate buffer solution (pH 6.98) with scan rate of 0.1 V/s. The average surface coverage and the apparent Michaelis–Menten constant are 6.69 × 10⁻¹¹ mol·cm⁻² and 2.47 μM. GOx/CILE shows excellent electrocatalytic activity towards glucose determination in the range of 0.1–800 μM with detection limit of 0.03 μM (S/N = 3). The biosensor has been successfully applied to the determination of glucose in human plasma with the average recoveries between 95.0% and 102.5% for three times determination. The direct electrochemistry of GOx on CILE is achieved without the help of any supporting film or any electron mediator. GOx/CILE is inexpensive, stable, repeatable and easy to be fabricated.     

Enhanced sensitivity for Cu(II) by a salicylidine-functionalized polysiloxane carbon paste electrode

A new approach for decreasing the detection limit for a copper(II) ion-selective electrode (ISE) is presented. The ISE is designed using salicylidine-functionalized polysiloxane in carbon paste. This work describes the attempts to develop the electrode and measurements of its characteristics. The new type of renewable three-dimensional chemically modified electrode could be used in a pH range of 2.3–5.4, and its detection limit is 2.7 × 10⁻⁸ mol L⁻¹ (1.2 μg L⁻¹). This sensor exhibits a good Nernstian slope of 29.4 ± 0.5 mV/decade in a wide linear concentration range of 2.3 × 10⁻⁷ to 1.0 × 10⁻³ mol L⁻¹ of Cu(II). It has a short response time (8 s) and noticeably high selectivity over other Cu(II) selective electrodes. Finally, it was satisfactorily used as an indicator electrode in complexometric titration with EDTA and determination of copper(II) in miscellaneous samples such as urine and various water samples.     

Simultaneous determination of pethidine and methadone by capillary electrophoresis with electrochemiluminescence detection of tris(2,2′-bipyridyl)ruthenium(II)

In this paper, we described a simple and rapid method, capillary electrophoresis with electrochemiluminescence (CE–ECL) detection using tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺), to simultaneously detect pethidine and methadone. Analytes were injected to separation capillary of 67.5 cm length (25 μm i.d., 360 μm o.d.) by electrokinetic injection for 10 s at 10 kV. Under the optimized conditions: ECL detection at 1.20 V, 30 mM sodium phosphate (pH 6.0) as running buffer, separation voltage at 14.0 kV, 5 mM Ru(bpy)₃²⁺ with 50 mM sodium phosphate (pH 6.5) in the detection cell, the linear range from 2.0 × 10^− 6 to 2.0 × 10^− 5 M for pethidine and 5.0 × 10^− 6 to 2.0 × 10^− 4 M for methadone and detection limits of 0.5 μM for both of them were achieved (S/N = 3). Relative standard derivations of the ECL intensity were 2.09% and 6.59% for pethidine and methadone, respectively.     

Electrogenerated chemiluminescence aptamer-based method for the determination of thrombin incorporating quenching of tris(2,2-bipyridine)ruthenium by ferrocene

A novel electrogenerated chemiluminescence (ECL) aptamer-based biosensing method for the determination of thrombin was developed on basis of a structure-switching ECL-dequenching mechanism. A thiolated ss-DNA capture probe, composing of a ss-DNA sequence to adopt two distinct structures-a DNA double strand with a complementary DNA sequence tagged with a ECL signal producer tris(2,2^′-bipyridyl)ruthenium derivative and a DNA duplex with a thrombin-binding aptamer tagged with a ECL-quencher ferrocene (FcDNA), was self-assembled onto surface of a gold electrode. In the presence of thrombin, the aptamer sequence prefers to form the aptamer-thrombin complex and the switch of the binding partners occurs in conjunction with the generation of a strong ECL signal owing to the dissociation of FcDNA. The integrated ECL intensity versus the concentration of thrombin was linear in the range from 2.0 × 10⁻¹⁰ M to 2.0 × 10⁻⁷ M. The detection limit was 6 × 10⁻¹¹ M. The relative standard derivation for 2.0 × 10⁻⁹ M was 5.7% (n = 7). This work demonstrates that the sensitivity and specificity of ECL aptamer-based method for proteins can be greatly improved using quenching ECL signal producer by a chemical quencher such as ferrocene.     

Voltammetric determination of N-acetylcysteine using a carbon paste electrode modified with copper(II) hexacyanoferrate(III)

The preparation and electrochemical characterization of a carbon paste electrode modified with copper(II) hexacyanoferrate(III) (CuHCF) as well as its behavior as electrocatalyst toward the oxidation of N-acetylcysteine were investigated. The electrochemical behavior of the modified electrode and the electrooxidation of N-acetylcysteine were explored using sweep linear voltammetry. The best voltammetric response was observed for a paste composition of 20% (w/w) copper(II) hexacyanoferrate(III) complex, acetate buffer solution at pH of 6.0 as the electrolyte and scan rate of 10 mV s^− 1. A linear voltammetric response for N-acetylcysteine was obtained in the concentration range from 1.2 × 10^− 4 to 8.3 × 10^− 4 mol L^− 1, with a detection limit of 6.3 × 10^− 5 mol L^− 1. The proposed electrode is useful for the quality control and routine analysis of N-acetylcysteine in pharmaceutical formulations.     

Amperometric glucose biosensor based on a gold nanorods/cellulose acetate composite film as immobilization matrix

We report on the utilization of gold nanorods to create a highly responsive glucose biosensor. The feasibility of an amperometric glucose biosensor based on immobilization of glucose oxidase (GOx) in gold nanorod is investigated. GOx is simply mixed with gold nanorods and cross-linked with a cellulose acetate (CA) medium by glutaraldehyde. The adsorption of GOx on the gold nanorods is confirmed by X-ray photoelectron spectroscopy (XPS) measurements. Circular dichroism (CD) and UV-spectrum results show that the activity of GOx was preserved after conjugating with gold nanorods. The current response of modified electrode is 10 times higher than that of without gold nanorods. Under optimal conditions, the biosensor shows high sensitivity (8.4 μA cm⁻² mM⁻¹), low detection limit (2 × 10⁻⁵ M), good storage stability and high affinity to glucose (). A linear calibration plot is obtained in the wide concentration range from 3 × 10⁻⁵ to 2.2 × 10⁻³ M.     

Electroanalytical and chromatographic determination of pentachlorophenol and related molecules in a contaminated soil: a real case example

Electroanalytical and chromatographic methodologies have been applied for the determination of pentachlorophenol (PCP) and some of its derivatives in real soil samples contaminated by industrial discharge. The analytes were extracted with hexane from soil samples collected at different points of the site and mixed to produce a representative sample. Square wave voltammetry (SWV) experiments were carried out on either a boron-doped diamond (BDD) electrode or a gold ultramicroelectrode (Au-UME) in an analyte composed by the Britton-Robinson (B-R) buffer at pH 5.5 with the direct addition of proper amounts of the extract. The voltammetric responses revealed an irreversible anodic peak at approximately 0.80 V vs. Ag/AgCl with a peak current showing a linear dependence on PCP concentration. This linear relationship yielded a detection limit (DL) of 2×10⁻⁸ mol l⁻¹ (or 5.5 μg l⁻¹) for the BDD electrode and 6.9×10⁻⁸ mol l⁻¹ (18.4 μg l⁻¹) for the Au-UME, while the independently measured HPLC detection limit was 1.1×10⁻⁸ mol l⁻¹ (3.0 μg l⁻¹). The application of electroanalytical and chromatographic methodologies in the analysis of soil extracts revealed, besides the PCP responses, signals for some related molecules such as o-tetrachlorobenzoquinone (o-chloranil), hexachlorobenzene and tetrachlorophenol. Recovering experiments for PCP showed a concentration of 27.5 mg kg⁻¹ for the electroanalytical determinations and 26.8 mg kg⁻¹ for the HPLC analysis, values exceedingly high if considering that the maximum residue limit established for natural waters by the Brazilian Environmental Agency is 10 μg l⁻¹.     

Simultaneous determination of hydroquinone and catechol at PASA/MWNTs composite film modified glassy carbon electrode

A poly-amidosulfonic acid and multi-wall carbon nanotubes composite (PASA/MWNTs) modified electrode has been constructed by electropolymerization on glassy carbon electrode (GCE). The electrochemical behaviors of hydroquinone (HQ) and catechol (CC) were investigated using cyclic and differential pulse voltammetries (DPVs) at the prepared electrode. Separation of the reductive peak potentials for HQ and CC was about 120 mV in pH 6.0 phosphate buffer solution (PBS), which makes it suitable for simultaneous determination of these compounds. In the presence of 1.0 × 10⁻⁴ mol L⁻¹ isomer, the reductive peak currents of DPV are proportional to the concentration of HQ in the range of 6.0 × 10⁻⁶ to 4.0 × 10⁻⁴ mol L⁻¹, and to that of CC in the range of 6.0 × 10⁻⁶ to 7.0 × 10⁻⁴ mol L⁻¹. When simultaneously changing the concentration of both HQ and CC, the linear concentration range of HQ (or CC) is 6.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ (or 6.0 × 10⁻⁶ to 1.8 × 10⁻⁴ mol L⁻¹), and the corresponding detection limits are 1.0 × 10⁻⁶ mol L⁻¹. The proposed method has been applied to simultaneous determination of HQ and catechol in water sample, and the results are satisfactory.     

Kinetic spectrophotometric method for the determination of urinary cobalt based on its catalytic effect on the oxidation of -adrenaline hydrochloride by hydrogen peroxide

A catalytic for determination of nanomolar concentrations of Co(II), i.e., oxidation of -adrenaline hydrochloride with H₂O² in alkaline medium, is proposed. The reaction gives a low limit of detection of 2.5 × 10 ⁻⁹ M Co(II) in the reaction mixture, good reproducibility with a relative standard deviation (R.S.D.) of 4−5% in the Co(II) concentration range 8.0 × 10⁻⁹−8.0 × 10⁻⁸M and good selectivity. On the basis of this indicator reaction, a catalytic-spectrophotometric method for the determination of cobalt in small urine samples (5.00 ml) was elaborated. The analysis of 17 urine samples, taken from healthy persons of different ages, gave cobalt concentrations in the range 0.20–1.50 μmol 1⁻¹. The R.S.D. for ten replicate analyses of a urine sample with an average cobalt content of 0.63 μmol 1⁻¹ was 5.6%. The reliability of the method was verified by a comparative photometric method (r = 0.9755) and by a determination based on known additions of cobalt (r = 0.9894).     

Studies on the kinetics of ascorbate oxidation at a ruthenium oxide hexacyanoferrate modified electrode towards the detection at microenvironments

The electrocatalytic oxidation of ascorbate on a ruthenium oxide hexacyanoferrate (RuOHCF) glassy carbon (GC) modified electrode was investigated at pH 6.9 by using rotating disc electrode (RDE) voltammetry. The influence of the systematic variation of rotation rate, film thickness, ascorbate concentration and the electrode potential indicated that the rate of cross-chemical reaction between Ru(III) centres immobilized into the film and ascorbate controls the overall process. The kinetic regime may be classified as a Sk″ mechanism and the second order rate constant for the surface electrocatalytic reaction was found to be 1.56 × 10⁻³ mol⁻¹ L¹ s⁻¹ cm. A carbon fibre microelectrode modified with the RuOHCF film was successfully used as an amperometric sensor to monitor the ascorbate diffusion in a simulated microenvironment experiment.