A compact miniaturized continuous flow system for the determination of urea content in milk

A multicommutation-based flow system with photometric detection was developed, employing an analytical microsystem constructed with low temperature co-fired ceramics (LTCC) technology, a solid-phase reactor containing particles of Canavalia ensiformis DC (urease source) immobilized with glutaraldehyde, and a mini-photometer coupled directly to the microsystem which monolithically integrates a continuous flow cell. The determination of urea in milk was based on the hydrolysis of urea in the solid-phase reactor and the ammonium ions produced were monitored using the Berthelot reaction. The analytical curve was linear in the urea concentration range from 1.0 × 10⁻⁴ to 5.0 × 10⁻³ mol L⁻¹ with a limit of detection of 8.0 × 10⁻⁶ mol L⁻¹. The relative standard deviation (RSD) for a 2.0 × 10⁻³ mol L⁻¹ urea solution was lower than 0.4% (n = 10) and the sample throughput was 13 h⁻¹. To check the reproducibility of the flow system, calibration curves were obtained with freshly prepared solutions on different days and the RSD obtained was 4.7% (n = 6). Accuracy was assessed by comparing the results of the proposed method with those from the official procedure and the data are in close agreement, at a 95% confidence level.     

Simple sensor for simultaneous determination of dihydroxybenzene isomers

A simple sensor based on bare carbon ionic liquid electrode was fabricated for simultaneous determination of dihydroxybenzene isomers in 0.1 mol L⁻¹ phosphate buffer solution (pH 6.0). The oxidation peak potential of hydroquinone was about 0.136 V, catechol was about 0.240 V, and resorcinol 0.632 V by differential pulse voltammetric measurements, which indicated that the dihydroxybenzene isomers could be separated absolutely. The sensor showed wide linear behaviors in the range of 5.0 × 10⁻⁷–2.0 × 10⁻⁴ mol L⁻¹ for hydroquinone and catechol, 3.5 × 10⁻⁶–1.535 × 10⁻⁴ mol L⁻¹ for resorcinol, respectively. And the detection limits of the three dihydroxybenzene isomers were 5.0 × 10⁻⁸, 2.0 × 10⁻⁷, 5.0 × 10⁻⁷ mol L⁻¹, respectively (S/N = 3). The proposed method could be applied to the determination of dihydroxybenzene isomers in artificial wastewater and the recovery was from 93.9% to 104.6%.     

Development of a liquid chromatography-mass spectrometry method for the determination of ursolic acid in rat plasma and tissue: application to the pharmacokinetic and tissue distribution study

A fast and sensitive liquid chromatography–mass spectrometry method was developed for the determination of ursolic acid (UA) in rat plasma and tissues. Glycyrrhetinic acid was used as the internal standard (IS). Chromatographic separation was performed on a 3.5 μm Zorbax SB-C18 column (30 mm × 2.1 mm) with a mobile phase consisting of methanol and aqueous 10 mM ammonium acetate using gradient elution. Quantification was performed by selected ion monitoring with (m/z)⁻ 455 for UA and (m/z)⁻ 469 for the IS. The method was validated in the concentration range of 2.5 − 1470 ng mL⁻¹ for plasma samples and 20 − 11760 ng g⁻¹ for tissue homogenates. The intra- and inter-day assay of precision in plasma and tissues ranged from 1.6% to 7.1% and 3.7% to 9.0%, respectively, and the intra- and inter-day assay accuracy was 84.2 − 106.9% and 82.1 − 108.1%, respectively. Recoveries in plasma and tissues ranged from 83.2% to 106.2%. The limits of detections were 0.5 ng mL⁻¹ or 4.0 ng g⁻¹. The recoveries for all samples were >90%, except for liver, which indicated that ursolic acid may metabolize in liver. The main pharmacokinetic parameters obtained were T _max = 0.42 ± 0.11 h, C _max = 1.10 ± 0.31 μg mL⁻¹, AUC = 1.45 ± 0.21 μg h mL⁻¹ and K _a = 5.64 ± 1.89 h⁻¹. The concentrations of UA in rat lung, spleen, liver, heart, and cerebellum were studied for the first time. This method is validated and could be applicable to the investigation of the pharmacokinetics and tissue distribution of UA in rats.     

Determination of enzyme activity inhibition by FTIR spectroscopy on the example of fructose bisphosphatase

A mid-infrared enzymatic assay for label-free monitoring of the enzymatic reaction of fructose-1,6-bisphosphatase with fructose 1,6-bisphosphate has been proposed. The whole procedure was done in an automated way operating in the stopped flow mode by incorporating a temperature-controlled flow cell in a sequential injection manifold. Fourier transform infrared difference spectra were evaluated for kinetic parameters, like the Michaelis–Menten constant (K _M) of the enzyme and V _max of the reaction. The obtained K _M of the reaction was 14 ± 3 g L⁻¹ (41 μM). Furthermore, inhibition by adenosine 5′-monophosphate (AMP) was evaluated, and the K _M^App value was determined to be 12 ± 2 g L⁻¹ (35 μM) for 7.5 and 15 μM AMP, respectively, with V _max decreasing from 0.1 ± 0.03 to 0.05 ± 0.01 g L⁻¹ min⁻¹. Therefore, AMP exerted a non-competitive inhibition.     

Simultaneous and sensitive determination of procaine and its metabolite for pharmaceutical quality control and pharmacokinetic research by using a graphite paste electrode

A simple, rapid, sensitive, and accurate method for simultaneous electrochemical determination of procaine and its metabolite (p-aminobenzoic acid, PABA) for pharmaceutical quality control and pharmacokinetic research was developed using a graphite paste electrode. The differential pulse voltammetric results revealed that procaine and p-aminobenzoic acid, respectively, showed well-defined anodic oxidation peaks on a carbon paste electrode with a current peak separation of 155 mV at a scan rate of 100 mV s⁻¹. This well separation of the current peaks for these two compounds in voltammetry enables us to simultaneously determine them. Good linearity (r > 0.998) between oxidation peak current and concentration was obtained in the range of 5.0 × 10⁻⁷–5.0 × 10⁻⁵ M for procaine and 5.0 × 10⁻⁷–2.0 × 10⁻⁵ M for PABA in pH 4.50 acetate buffer solution. The detection limit for both analytes is 5 × 10⁻⁸ M (S/N = 3:1). The present voltammetric method has been successfully used to determine trace p-aminobenzoic acid in procaine hydrochloride injection and procaine in plasma with a linear relationship of current to its concentration ranging from 1.0 × 10⁻⁶ to 5.0 × 10⁻⁵ M (correlation coefficient of 0.9981) with a low detection limit of 5.0 × 10⁻⁷ M (S/N = 3:1). This validated method is promising to the study of pharmacokinetics in Sprague–Dawley rat and rabbit plasma after an intravenous administration of procaine hydrochloride injection.     

Determination of thiocyanate ions at nanolevel in real samples using coated graphite electrode based on synthesised macrocyclic Zn(II) complex

The electrode characteristics and selectivities of PVC-based thiocyanate selective polymeric membrane electrode (PME) incorporating the newly synthesized zinc complex of 6,7:14,15-Bzo₂-10,11-(4-methylbenzene)-[15]-6,8,12,14-tetraene-9,12-N₂-1,5-O₂ (I ₁ ) and zinc complex of 6,7:14,15-Bzo₂-10,11-(4-methylbenzene)-[15]-6,14-diene-9,12-dimethylacrylate-9,12-N₂-1,5-O₂ (I ₂ ) are reported here. The best response was observed with the membrane having a composition of I₂:PVC:o-NPOE:HTAB in the ratio of 6:33:59:2 (w/w; milligram). This electrode exhibited Nernstian slope for thiocyanate ions over working concentration range of 4.4 × 10⁻⁷ to 1.0 × 10⁻² mol L⁻¹ with detection limit of 2.2 × 10⁻⁷ mol L⁻¹. The performance of this electrode was compared with coated graphite electrode (CGE), which showed better response characteristics w.r.t Nernstian slope 59.0 ± 0.2 mV decade⁻¹ activity, wide concentration range of 8.9 × 10⁻⁸ to 1.0 × 10⁻² mol L⁻¹ and detection limit of 6.7 × 10⁻⁸ mol L⁻¹. The response time for CGE and PME was found to be 8 and 10 s, respectively. The proposed electrode (CGE) was successfully applied to direct determination of thiocyanate in biological and environmental samples and also as indicator electrode in potentiometric titration of SCN⁻ ion.     

Development of a highly precise ID-ICP-SFMS method for analysis of low concentrations of lead in rice flour reference materials

Microwave digestion and isotope dilution inductively coupled plasma mass spectrometry (ID-ICP-SFMS) has been applied to the determination of Pb in rice flour. In order to achieve highly precise determination of low concentrations of Pb, the digestion blank for Pb was reduced to 0.21 ng g⁻¹ after optimization of the digestion conditions, in which 20 mL analysis solution was obtained after digestion of 0.5 g rice flour. The observed value of Pb in a non-fat milk powder certified reference material (CRM), NIST SRM 1549, was 16.8 ± 0.8 ng g⁻¹ (mean ± expanded uncertainty, k = 2; n = 5), which agreed with the certified value of 19 ± 3 ng g⁻¹ and indicated the effectiveness of the method. Analytical results for Pb in three brown rice flour CRMs, NIST SRM 1568a, NIES CRM 10-a, and NIES CRM 10-b, were 7.32 ± 0.24 ng g⁻¹ (n = 5), 1010 ± 10 ng g⁻¹ (n = 5), and 1250 ± 20 ng g⁻¹ (n = 5), respectively. The concentration of Pb in a candidate white rice flour reference material (RM) sample prepared by the National Metrology Institute of Japan (NMIJ) was observed to be 4.36 ± 0.28 ng g⁻¹ (n = 10 bottles). Figure Digestion blank of Pb was carefully reduced to approximately 0.2 ng g^-1 which permitted the highly precise determination of Pb at low ng g^-1 level in foodstuff samples by ID-SFMS     

Ethanol Production from Cashew Apple Bagasse: Improvement of Enzymatic Hydrolysis by Microwave-Assisted Alkali Pretreatment

In this work, the potential of microwave-assisted alkali pretreatment in order to improve the rupture of the recalcitrant structures of the cashew able bagasse (CAB), lignocellulosic by-product in Brazil with no commercial value, is obtained from cashew apple process to juice production, was studied. First, biomass composition of CAB was determined, and the percentage of glucan and lignin was 20.54 ± 0.70% and 33.80 ± 1.30%, respectively. CAB content in terms of cellulose, hemicelluloses, and lignin, 19.21 ± 0.35%, 12.05 ± 0.37%, and 38.11 ± 0.08%, respectively, was also determined. Results showed that, after enzymatic hydrolysis, alkali concentration exerted influence on glucose formation, after pretreatment with 0.2 and 1.0 mo L⁻¹ of NaOH (372 ± 12 and 355 ± 37 mg g_glucan⁻¹) when 2% (w/v) of cashew apple bagasse pretreated by microwave-assisted alkali pretreatment (CAB-M) was used. On the other hand, pretreatment time (15–30 min) and microwave power (600–900 W) exerted no significant effect on hydrolysis. On enzymatic hydrolysis step, improvement on solid percentage (16% w/v) and enzyme load (30 FPU g_CAB-M⁻¹) increased glucose concentration to 15 g L⁻¹. The fermentation of the hydrolyzate by Saccharomyces cerevesiae resulted in ethanol concentration and productivity of 5.6 g L⁻¹ and 1.41 g L⁻¹ h⁻¹, respectively.     

A new amperometric H<Subscript>2</Subscript>O<Subscript>2</Subscript> biosensor based on nanocomposite films of chitosan–MWNTs,hemoglobin, and silver nanoparticles

A new H₂O₂ biosensor was fabricated on the basis of nanocomposite films of hemoglobin (Hb), silver nanoparticles (AgNPs), and multiwalled carbon nanotubes (MWNTs)–chitosan (Chit) dispersed solution immobilized on glassy carbon electrode (GCE). The immobilized Hb displayed a pair of well-defined and reversible redox peaks with a formal potential (E ^θ′) of −22.5 mV in 0.1 M pH 7.0 phosphate buffer solution. The apparent heterogeneous electron transfer rate constants (k _s) in the Chit–MWNTs film was evaluated as 2.58 s⁻¹ according to Laviron’s equation. The surface concentration (Γ*) of the electroactive Hb in the Chit–MWNTs film was estimated to be (2.48 ± 0.25) × 10⁻⁹ mol cm⁻². Meanwhile, the Chit–MWNTs/Hb/AgNPs/GCE demonstrated excellently electrocatalytical ability to H₂O₂. Its apparent Michaelis–Menten constant (K _M^app) for H₂O₂ was 0.0032 mM, showing a good affinity. Under optimal conditions, the biosensors could be used for the determination of H₂O₂ ranging from 6.25 × 10⁻⁶ to 9.30 × 10⁻⁵ mol L⁻¹ with a detection limit of 3.47 × 10⁻⁷ mol L⁻¹ (S/N = 3). Furthermore, the biosensor possessed rapid response to H₂O₂ and good stability, selectivity, and reproducibility.     

Organosilica composite for preconcentration of phenolic compounds from aqueous solutions

A new adsorbent is proposed for the solid-phase extraction of phenol and 1-naphthol from polluted water. The adsorbent (TX-SiO₂) is an organosilica composite made from a bifunctional immobilized layer comprising a major fraction (91%) of hydrophilic diol groups and minor fraction (9%) of the amphiphilic long-chain nonionic surfactant Triton X-100 (polyoxyethylated isooctylphenol) (TX). Under static conditions phenol was quantitatively extracted onto TX-SiO₂ in the form of a 4-nitrophenylazophenolate ion associate with cetyltrimethylammonium bromide. The capacity of TX-SiO₂ for phenol is 2.4 mg g⁻¹ with distribution coefficients up to 3.4 × 10⁴ mL g⁻¹; corresponding data for 1-naphthol are 1.5 mg g⁻¹ and 3 × 10³ mL g⁻¹. The distribution coefficient does not change significantly for solution volumes of 0.025–0.5 L and adsorbent mass less than 0.03 g; 1–90 μg analyte can be easily eluted by 1–3 mL acetonitrile with an overall recovery of 98.2% and 78.3% for phenol and 1-naphthol, respectively. Linear correlation between acetonitrile solution absorbance (A ₅₄₀) and phenol concentration (C) in water was found according to the equation A ₅₄₀ = (6 ± 1) × 10⁻² + (0.9 ± 0.1)C (μmol L⁻¹) with a detection range from 1 × 10⁻⁸ mol L⁻¹ (0.9 μL g⁻¹) to 2 × 10⁻⁷ mol L⁻¹ (19 μL g⁻¹), a limit of quantification of 1 μL g⁻¹ (preconcentration factor 125), correlation coefficient of 0.936, and relative standard deviation of 2.5%. A solid-phase colorimetric method was developed for quantitative determination of 1-naphthol on adsorbent phase using scanner technology and RGB numerical analysis. The detection limit of 1-naphthol with this method is 6 μL g⁻¹ while the quantification limit is 20 μL g⁻¹. A test system was developed for naked eye monitoring of 1-naphthol impurities in water. The proposed test kit allows one to observe changes in the adsorbent color when 1-naphthol concentration in water is 0.08–3.2 mL g⁻¹.     

Electrochemical behaviors of metol on ionic-liquid-modified carbon paste electrode and its analytical application

The electrochemical behaviors of metol on an ionic liquid N-butylpyridinium hexafluorophosphate modified carbon paste electrode (IL-CPE) were studied in this paper. The results indicated that a pair of well-defined quasi-reversible redox peaks of metol appeared with the decrease of overpotential and the increase of redox peak current, which was the characteristics of electrocatalytic oxidation. The electrocatalytic mechanism was discussed and the electrochemical parameters were calculated with results of the charge-transfer coefficient (α) as 0.45, the electrode reaction rate constant (k _s) as 4.02 × 10⁻³ s⁻¹, and the diffusion coefficient (D) as 6.35 × 10⁻⁵ cm²/s. Under the optimal conditions, the anodic peak current was linear with the metol concentration in the range of 5.0 × 10⁻⁶ ∼ 1.0 × 10⁻³ mol/L (n = 11, γ = 0.994) and the detection limit was estimated as 2.33 × 10⁻⁶ mol/L (3σ). The proposed method was successfully applied to determination of metol content in synthetic samples and photographic solutions.     

Electrochemical methods for simultaneous determination of trace amounts of dopamine and uric acid using a carbon paste electrode incorporated with multi-wall carbon nanotubes and modified with α-cyclodextrine

In this work, we investigate the electrochemical activity of dopamine (DA) and uric acid (UA) using both a bare and a modified carbon paste electrode as the working electrode, with a platinum wire as the counter electrode and a silver/silver chloride (Ag/AgCl) as the reference electrode. The modified carbon paste electrode consists of multi-walled carbon nanotubes (>95%) treated with α-cyclodextrine, resulting in an electrode that exhibits a significant catalytic effect toward the electro-chemical oxidation of DA in a 0.2-M Britton–Robinson buffer solution (pH 5.0). The peak current increases linearly with the DA concentration within the molar concentration ranges of 2.0 × 10⁻⁶ to 5.0 × 10⁻⁵ M and 5.0 × 10⁻⁵ to 1.9 × 10⁻⁴ M. The detection limit (signal to noise >3) for DA was found to be 1.34 × 10⁻⁷ M, respectively. In this work, voltammetric methods such as cyclic voltammetry, chronoamperometry, chronocuolometry, differential pulse and square wave voltammetry, and linear sweep and hydrodynamic voltammetry were used. Cyclic voltammetry was used to investigate the redox properties of the modified electrode at various scan rates. The diffusion coefficient (D, cm² s⁻¹ = 3.05 × 10⁻⁵) and the kinetic parameters such as the electron transfer coefficient (α = 0.51) and the rate constant (k, cm³ mol⁻¹ s⁻¹ = 1.8 × 10³) for DA were determined using electrochemical approaches. By using differential pulse voltammetry for simultaneous measurements, we obtained two peaks for DA and UA in the same solution, with the peak separation approximately 136 mV. The average recovery was measured at 102.45% for DA injection.     

A polymer electrolyte containing ionic liquid for possible applications in photoelectrochemical solar cells

Various iodide ion conducting polymer electrolytes have been studied as candidate materials for fabricating photoelectrochemical (PEC) solar cells and energy storage devices. In this study, enhanced ionic conductivity values were obtained for the ionic liquid tetrahexylammonium iodide containing polyethylene oxide (PEO)-based plasticized electrolytes. The analysis of thermal properties revealed the existence of two phases in the electrolyte, and the conductivity measurements showed a marked conductivity enhancement during the melting of the plasticizer-rich phase of the electrolyte. Annealed electrolyte samples showed better conductivity than nonannealed samples, revealing the existence of hysteresis. The optimum conductivity was shown for the electrolytes with PEO:salt = 100:15 mass ratio, and this sample exhibited the minimum glass transition temperature of 72.2 °C. For this optimum PEO to salt ratio, the conductivity of nonannealed electrolyte was 4.4 × 10⁻⁴ S cm⁻¹ and that of the annealed sample was 4.6 × 10⁻⁴ S cm⁻¹ at 30 °C. An all solid PEC solar cell was fabricated using this annealed electrolyte. The short circuit current density (I _SC), the open circuit voltage (V _OC), and the power conversion efficiency of the cell are 0.63 mA cm⁻², 0.76 V, and 0.47% under the irradiation of 600 W m⁻² light.     

Molecularly imprinted on-line solid-phase extraction combined with chemiluminescence for the determination of pazufloxacin mesilate

A novel molecularly imprinted polymer solid-phase extraction (MISPE) with flow-injection chemiluminescence (CL) was developed for the determination of pazufloxacin mesilate (PZFX). The molecularly imprinted polymer (MIP) was synthesized by using PZFX as the imprinting molecule. A glass tube packed the particles of the MIP was employed as MISPE micro-column, which was connected into the sampling loop of the eight-way injection valve for on-line selective preconcentration and extraction of PZFX. The eluent of acetonitrile:acetic acid (9:1, v:v) was used as carrier for eluting the adsorbed PZFX to react with the mixture of cerium(IV) and sodium sulfite in the flow cell to produce strong CL. The relative intensity of CL was linear to PZFX concentration in the range from 2.5 × 10⁻⁹ to 2.5 × 10⁻⁷ g mL⁻¹. The limit of detection was 7 × 10⁻¹⁰ g mL⁻¹ (3 σ) and the relative standard deviation for 5 × 10⁻⁸ g mL⁻¹of PZFX solution was 3.7% (n = 7). This method has been applied to the determination of PZFX in human urine.     

A Superoxide Dismutase Purified from the Rhizome of <Emphasis Type="Italic">Curcuma aeruginosa</Emphasis> Roxb. as Inhibitor of Nitric Oxide Production in the Macrophage-like RAW 264.7 Cell Line

Superoxide dismutase (SOD, EC 1.15.1.1) is a metalloenzyme or antioxidant enzyme that catalyzes the disproportionation of the harmful superoxide anionic radical to hydrogen peroxide and molecular oxygen. Due to its antioxidative effects, SOD has long been applied in medicinal treatment, cosmetic, and other chemical industries. Fifteen Zingiberaceae plants were tested for SOD activity in their rhizome extracts. The crude homogenate and ammonium sulfate cut fraction of Curcuma aeruginosa were found to contain a significant level of SOD activity. The SOD enzyme was enriched 16.7-fold by sequential ammonium sulfate precipitation, diethylaminoethyl cellulose ion exchange, and Superdex 75 gel filtration column chromatography. An overall SOD yield of 2.51 % with a specific activity of 812.20 U/mg was obtained. The enriched SOD had an apparent MW of 31.5 kDa, as judged by sodium dodecyl sulfate polyacrylamide gel electrophoresis, and a pH and temperature optima of 4.0 and 50 °C. With nitroblue tetrazolium and riboflavin as substrates, the K _m values were 57.31 ± 0.012 and 1.51 ± 0.014 M, respectively, with corresponding V _max values of 333.7 ± 0.034 and 254.1 ± 0.022 μmol min⁻¹ mg protein⁻¹. This SOD likely belongs to the Fe- or Mn-SOD category due to the fact that it was insensitive to potassium cyanide or hydrogen peroxide inhibition, but was potentially weakly stimulated by hydrogen peroxide, and stimulated by Mn²⁺and Fe²⁺ ions. Moreover, this purified SOD also exhibited inhibitory effects on lipopolysaccharide-induced nitric oxide production in cultured mouse macrophage cell RAW 264.7 in a dose-dependent manner (IC₅₀ = 14.36 ± 0.15 μg protein/ml).     

Electro-catalysis by immobilised human flavin-containing monooxygenase isoform 3 (hFMO3)

Human flavin-containing monooxygenases are the second most important class of drug-metabolizing enzymes after cytochromes P450. Here we report a simple but functional and stable enzyme-electrode system based on a glassy carbon (GC) electrode with human flavin-containing monooxygenase isoform 3 (hFMO3) entrapped in a gel cross-linked with bovine serum albumin (BSA) by glutaraldehyde. The enzymatic electrochemical responsiveness is characterised by using well-known substrates: trimethylamine (TMA), ammonia (NH₃), triethylamine (TEA), and benzydamine (BZD). The apparent Michaelis–Menten constant (K′_M) and apparent maximum current (I′_max) are calculated by fitting the current signal to the Michaelis–Menten equation for each substrate. The enzyme-electrode has good characteristics: the calculated sensitivity was 40.9 ± 0.5 mA mol⁻¹ L cm⁻² for TMA, 43.3 ± 0.1 mA mol⁻¹ L cm⁻² for NH₃, 45.2 ± 2.2 mA mol⁻¹ L cm⁻² for TEA, and 39.3 ± 0.6 mA mol⁻¹ L cm⁻² for BZD. The stability was constant for 3 days and the inter-electrode reproducibility was 12.5%. This is a novel electrochemical tool that can be used to investigate new potential drugs against the catalytic activity of hFMO3.     

Simultaneous determination of catechol and hydroquinone based on poly (diallyldimethylammonium chloride) functionalized graphene-modified glassy carbon electrode

Simultaneous determination of catechol (CC) and hydroquinone (HQ) were investigated by voltammetry based on glassy carbon electrode (GCE) modified by poly (diallyldimethylammonium chloride) (PDDA) functionalized graphene (PDDA-G). The modified electrode showed excellent sensitivity and selectivity properties for the two dihydroxybenzene isomers. In 0.1 mol/L phosphate buffer solution (PBS, pH 7.0), the oxidation peak potential difference between CC and HQ was 108 mV, and the peaks on the PDDA-G/GCE were three times as high as the ones on graphene-modified glass carbon electrode. Under optimized conditions, the PDDA-G/GCE showed wide linear behaviors in the range of 1 × 10⁻⁶−4 × 10⁻⁴ mol/L for CC and 1 × 10⁻⁶−5 × 10⁻⁴ mol/L for HQ, with the detection limits 2.0 × 10⁻⁷ mol/L for CC and 2.5 × 10⁻⁷ mol/L for HQ (S/N = 3) in mixture, respectively. Some kinetic parameters, such as the electron transfer number (n), charge transfer coefficient (α), and the apparent heterogeneous electron transfer rate constant (k _s), were calculated. The proposed method was applied to simultaneous determine CC and HQ in real water samples of Yellow River with satisfactory results.     

An electrochemiluminescence sensor for determination of durabolin based on CdTe QD films by layer-by-layer self-assembly

This work reported for the first time the use of flow injection electrochemiluminescence (FI-ECL) sensor for the determination of durabolin in an aqueous system based on CdTe quantum dot (QD) films. Aqueous CdTe colloidal solutions were prepared using thioglycolic acid as a capping agent. Zetasizer Nano ZS (Malvern, UK) was employed to characterize the size of CdTe QDs. The UV–vis and photoluminescence spectra of samples were systematically characterized. Indium tin oxide (ITO) slide glass was modified with CdTe QDs by layer-by-layer self-assembly. CdTe QD films were packed into a homemade cell and used as a recognizer of the FI-ECL sensor to determine durabolin. The intensive anodic ECL emission was obtained at a starting potential of +1.3 V (vs. Ag/AgCl) in a carbonate bicarbonate buffer solution with a pH of 9.93 at an ITO electrode. The ECL intensity was correlated linearly with the concentration of durabolin over the range of 1.0 × 10⁻⁸–1.0 × 10⁻⁵ g mL⁻¹, and the detection limit was 2.5 × 10⁻⁹ g mL⁻¹. The relative standard deviation for the determination of 1.0 × 10⁻⁶ g mL⁻¹ durabolin was 1.04% (n = 11). This simple and sensitive sensor revealed good reproducibility for ECL analysis. As a result, the new FI-ECL sensor had been successfully applied to the determination of durabolin in food samples. This strategy could be easily realized and opened new avenues for the applications of QDs in ECL biosensing.     

Cell membrane chromatography competitive binding analysis for characterization of α<Subscript>1A</Subscript> adrenoreceptor binding interactions

A new high α_1A adrenoreceptor (α_1AAR) expression cell membrane chromatography (CMC) method was developed for characterization of α_1AAR binding interactions. HEK293 α_1A cell line, which expresses stably high levels of α_1AAR, was used to prepare the stationary phase in the CMC model. The HEK293 α_1A/CMC-offline-HPLC system was applied to specifically recognize the ligands which interact with the α_1AAR, and the dissociation equilibrium constants (K _D) obtained from the model were (1.87 ± 0.13) × 10⁻⁶ M for tamsulosin, (2.86 ± 0.20) × 10⁻⁶ M for 5-methylurapidil, (3.01 ± 0.19) × 10⁻⁶ M for doxazosin, (3.44 ± 0.19) × 10⁻⁶ M for terazosin, (3.50 ± 0.21) × 10⁻⁶ M for alfuzosin, and (7.57 ± 0.31) × 10⁻⁶ M for phentolamine, respectively. The competitive binding study between tamsulosin and terazosin indicated that the two drugs interacted at the common binding site of α_1AAR. However, that was not the case between tamsulosin and oxymetazoline. The results had a positive correlation with those from radioligand binding assay and indicated that the CMC method combined modified competitive binding could be a quick and efficient way for characterizing the drug–receptor interactions.     

Circular dichroism thermal lens microscope in the UV wavelength region (UV-CD-TLM) for chiral analysis on a microchip

We have developed a circular-dichroism thermal lens microscope for UV wavelengths (UV-CD-TLM), for the first time, to realize sensitive chiral analysis on a microchip. Quasi-continuous-wave phase modulation of a pulsed UV laser was used to generate left-circularly polarized light and right-circularly polarized light and to detect the generated TL signal amplitude and phase with a lock-in amplifier. The amplitude and phase were used to determine the concentration and chirality, respectively, of a sample. The basic principle of UV-CD-TLM for chiral analysis on a microchip was verified by measuring aqueous solutions of optically active camphorsulfonic acids (CSA). Lower limits of detection (LOD) were calculated at S/N = 2 and were 8.7 × 10⁻⁴ mol L⁻¹ (ΔA = 5.2 × 10⁻⁶ Abs.) for (+)-CSA and 8.4 × 10⁻⁴ mol L⁻¹ (ΔA = 5.0 × 10⁻⁶ Abs.) for (−)-CSA. In terms of number of molecules, LODs for UV-CD-TLM were calculated to be 8.7 fmol and 8.4 fmol, respectively. This is at least three orders of magnitude lower than previously obtained. The applicability of UV-CD-TLM for chiral analysis on a microchip was verified. Figure Sensitive chiral analysis by thermal lens microscope (TLM)