Temperature dependence of the magnetic properties and magnetoimpedance of nanocrystalline Fe<Subscript>73.5</Subscript>Si<Subscript>16.5</Subscript>B<Subscript>6</Subscript>Nb<Subscript>3</Subscript>Cu<Subscript>1</Subscript> ribbons

The temperature dependences of the magnetic properties and the magnetoimpedance effect of soft magnetic nanocrystalline Fe_73.5Si_16.5B₆Nb₃Cu₁ alloy ribbons are studied in the temperature range 24–160°C. A high temperature sensitivity of the impedance and the magnetoimpedance effect of the ribbons are detected in the ac frequency range 0.1–50 MHz. At an ac frequency of 50 MHz, the change in the impedance reaches 0.2 Ω/°C (0.5%/°C) in the temperature range 85–160°C. When the temperature increases, a monotonically decreasing character of the dependence of the magnetoimpedance effect on the applied magnetic field changes into a dependence having an increasing initial segment. The effect of temperature on the magnetoimpedance properties of the soft magnetic nanocrystalline ribbons is shown to result from temperature-induced changes in their electrical conductivity, magnetization, and effective magnetic anisotropy.     

Magnetic properties of the Nd<Subscript>0.5</Subscript>Gd<Subscript>0.5</Subscript>Fe<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript> single crystal

The magnetic properties of the Nd_0.5Gd_0.5Fe₃(BO₃)₄ single crystal have been studied in principal crystallographic directions in magnetic fields to 90 kG in the temperature range 2–300 K; in addition, the heat capacity has been measured in the range 2–300 K. It has been found that, below the Néel temperature T _N = 32 K down to 2 K, the single crystal exhibits an easy-plane antiferromagnetic structure. A hysteresis has been detected during magnetization of the crystal in the easy plane in fields of 1.0–3.5 kG, and a singularity has been found in the temperature dependence of the magnetic susceptibility in the easy plane at a temperature of 11 K in fields B < 1 kG. It has been shown that the singularity is due to appearance of the hysteresis. The origin of the magnetic properties of the crystal near the hysteresis has been discussed.     

Muon-spin-relaxation investigation of EuMn<Subscript>2</Subscript>O<Subscript>5</Subscript>

The magnetic properties of the EuMn₂O₅ multiferroic (samples consisting of single crystals and ceramic samples) have been investigated by the muon-spin-relaxation (μSR) method in the temperature range of 10–300 K. Below the magnetic ordering temperature T _N = 40 K, the loss of the polarization of muons and the effect of the external magnetic field have been observed. Both phenomena can be explained by an additional channel of the depolarization of muons owing to the appearance of muons in a medium with a low electron density due to the charge separation process (the redistribution of the electron density in the phase transition process). The “memory” phenomenon has been revealed in a sample in the external magnetic field; the memory relaxation time depends on the size of the structure units of the samples (single crystals or ceramic grains).     

Microstructure,dielectric and piezoelectric properties of (K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>)NbO<Subscript>3</Subscript>-Ba(Ti<Subscript>0.95</Subscript>Zr<Subscript>0.05</Subscript>)O<Subscript>3</Subscript> lead-free ceramics with CuO sintering aid

Using an ordinary ceramic fabrication technique, we fabricated lead-free (1-x)(K_0.5Na_0.5)NbO₃-xBa(Ti_0.95Zr_0.05)O₃ ceramics with CuO sintering aid . Ba(Ti_0.95Zr_0.05)O₃ diffuses into (K_0.5Na_0.5)NbO₃ to form a new solid solution. The ceramics with perovskite structure possess orthorhombic phase at x≤0.04 and become tetragonal phase at x≥0.06. Both the paraelectric cubic–ferroelectric tetragonal and the ferroelectric tetragonal–ferroelectric orthorhombic phase transition temperatures decrease with increasing the concentration of Ba(Ti_0.95Zr_0.05)O₃. The doping of CuO effectively promotes the densification of the ceramics. The coexistence of the orthorhombic and tetragonal phases at 0.04<x<0.06 and the improvement in sintering performances of the ceramics significantly enhance the piezoelectric and dielectric properties at room temperature. The ceramics with x=0.04–0.06 and y=0.75–1.50 possess excellent properties: d₃₃=119–185 pC/N, k_P=37–44%, k_t=35–49%, ε=341–1129, cosδ=0.7–4.4% and T_c=312–346 °C. PACS 77.65.-j; 77.84.Dy; 77.84.-s     

Magnetic and transport properties of monocrystalline<Emphasis Type="Italic">Fe</Emphasis><Subscript>3</Subscript><Emphasis Type="Italic">O</Emphasis><Subscript>4</Subscript>

A monocrystal ofFe ₃ O ₄ is characterized by resistance, magnetoresistance and magnetic measurements in a temperature range from 4.2 K to 350 K and magnetic field-cycling from −9 T to 9 T. The resistance measurements revealed a metal-insulator Verwey transition (VT) atT _v =123.76 K with activation energy E=92.5 meV at T >T _v and temperature-substitute for the activation energy below the VT,T ₀=E/k _B ≈3800 K within 70 K–110K. The magnetotransport results independently verified the VT at 123.70 K, with discontinuous change in the magnetic moment ΔM≈0.21 ΔM≈0.21μ _B and resistance hysteresis, dependent on the magnetic field in a narrow temperature range of 0.4° around theT _v . The magnetic characterization established self consistentlyT _v as ≈123.67 K, the jump in the magnetization at the VT≈0.25μ _B and confirmed, that the magnetocrystalline anisotropy is the main microscopic mechanism responsible for the magnetization of the monocrystal (88%) with additional natural and imposed defects contributing as 12%.     

Magnetocaloric effect in the Sm<Subscript>0.55</Subscript>Sr<Subscript>0.45</Subscript>MnO<Subscript>3</Subscript> manganite

The magnetocaloric effect ΔT has been studied by a direct method in two samples of the manganite Sm_0.55Sr_0.45MnO₃, namely, a single crystal (sample A) and a ceramic sample (sample C). The temperature dependences of the ΔT effect of both samples exhibit a maximum at T _max = 143.3 K for the sample A and T _max = 143 K for the sample C. In these maxima, the values of the ΔT effect are 0.8 and 0.4 K in the magnetic field H = 14.2 kOe for the samples A and C, respectively. In addition, the ΔT(T) curve of the sample A has a minimum at T _min = 120 K, in which ΔT = −0.1 K. The maximum value of the ΔT effect increases with an increase in the magnetic field H in the range of magnetic fields up to 14.2 kOe, and the rate of this increase at H > 8 kOe is higher than that at H < 8 kOe. These features of the ΔT effect are explained by the presence of ferromagnetic and antiferromagnetic A- and CE-type clusters in the samples.     

Magnetic properties of nanoparticle La<Subscript>0.7</Subscript>Ca<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript> under applied hydrostatic pressure

Pressure effects on magnetic properties of two La_0.7Ca_0.3MnO₃ nanoparticle samples with different mean particle sizes were investigated. Both the samples were prepared by the glycine-nitrate method: sample S—as-prepared (10 nm), and sample S₉₀₀—subsequently annealed at 900 °C for 2 h (50 nm). Magnetization measurements revealed remarkable differences in magnetic properties with the applied pressure up to 0.75 GPa: (i) for S sample, both transition temperatures, para-to-ferromagnetic T _C = 120 K and spin-glass-like transition T _f = 102 K, decrease with the pressure with the respective pressure coefficients dT _C/dP = −2.9 K/GPa and dT _f/dP = −4.4 K/GPa; (ii) for S₉₀₀ sample, para-to-ferromagnetic transition temperature T _C = 261 K increases with pressure with the pressure coefficient dT _C/dP = 14.8 K/GPa. At the same time, saturation magnetization M _S recorded at 10 K decreases/increases with pressure for S/S₉₀₀ sample, respectively. Explanation of these unusual pressure effects on the magnetism of sample S is proposed within the scenario of the combined contributions of two types of disorders present in the system: surface disorder introduced by the particle shell, and structural disorder of the particle core caused by the prominent Jahn–Teller distortion. Both disorders tend to vanish with the annealing of the system (i.e., with the nanoparticle growth), and so the behavior of the sample S₉₀₀ is similar to that previously observed for the bulk counterpart.     

Evolution of elemental distribution in free-standing structures of Zr/ZrSi<Subscript>2</Subscript> with MoSi<Subscript>2</Subscript> and ZrSi<Subscript>2</Subscript> protective coatings under annealing

An analysis of the in-depth distribution of elements in annealed samples of multilayer Zr/ZrSi₂ EUV filters with protective layers of MoSi₂ and ZrSi₂ was performed by secondary ion mass spectrometry (SIMS). The vacuum annealing of the samples was performed at temperatures of up to 720–950°C for 3–7 h and at a residual pressure of ∼10⁻⁷ torr. It was demonstrated that MoSi₂ coatings effectively inhibit the accumulation of oxygen by the heated film, which is the process that determines the optical degradation of the filter.     

Magnetotransport properties of La<Subscript>0.67</Subscript>Ca<Subscript>0.33</Subscript>MnO<Subscript>3</Subscript> with different grain sizes

The magnetotransport and magnetoresistive (MR) properties of manganese-based La_0.67Ca_0.33MnO₃ perovskite with different grain sizes are reported. The electrical resistivity was measured as a function of temperature in magnetic fields of 0.5 and 1 T. The insulator–metal transition temperature, T _IM, shifted to a higher temperature with the application of the magnetic field. In zero field, T _IM is almost constant (∼271 K) for all samples except for the sample with the largest grain size, where T _IM=265 K. The temperature dependence of resistivity was fitted with several equations in the metallic (ferromagnetic) region and the insulating (paramagnetic) region. The density of states at the Fermi level, N(E _F), and the activation energy of electron hopping were estimated by fitting the resistivity versus temperature curves. The ρ–T ² curves are nearly linear in the metallic regime, but the ρ–T ^2.5 curves exhibit a deviation from linearity. The variable range hopping model and small polaron hopping model fit the data well in the high-temperature region, indicating the existence of the Jahn–Teller distortion that localizes the charge carriers. MR was found to increase with an increase in the magnetic field, an effect which is attributed to the intergrain spin tunneling effect.     

Manganese-doped ZnSiAs<Subscript>2</Subscript> chalcopyrite: A new advanced material for spintronics

A new spintronics material with the Curie temperature above room temperature, the ZnSiAs₂ chalcopyrite doped with 1 and 2 wt % Mn, is synthesized. The magnetization, electrical resistivity, magnetoresistance, and the Hall effect of these compositions are studied. The temperature dependence of the electrical resistivity follows a semiconducting pattern with an activation energy of 0.12–0.38 eV (in the temperature range 124 K ≤ T ≤ 263 K for both compositions). The hole mobility and concentration are 1.33, 2.13 cm²/V s and 2.2 × 10¹⁶, 8 × 10¹⁶ cm⁻³ at T = 293 K for the 1 and 2 wt % Mn compositions, respectively. The magnetoresistance of both compositions, including the region of the Curie point, does not exceed 0.4%. The temperature dependence of the magnetization M(T) of both compositions exhibits a complicated character; indeed, for T ≤ 15 K, it is characteristic of superparamagnets, while for T > 15 K, spontaneous magnetization appears which correspond to a decreased magnetic moment per formula unit as compared to that which would be observed upon complete ferromagnetic ordering of Mn²⁺ spins or antiferromagnetic ordering of spins of the Mn²⁺ and Mn³⁺ ions. Thus, for T > 15 K, it is a frustrated ferro- or ferrimagnet. It is found that, unlike the conventional superparamagnets, the cluster moment μ _c in these compositions depends on the magnetic field: ∼12000–20000μ_B for H = 0.1 kOe, ∼52–55μ_B for H = 11 kOe, and ∼8.6–11.0μ_B at H = 50 kOe for the compositions with 1 and 2 wt % Mn, respectively. The specific features of the magnetic properties are explained by the competition between the carrier-mediated exchange and superexchange interactions.     

Effect of low-temperature treatment and subsequent high-temperature annealing on the critical current density of YBa2Cu3O y

The field dependences of the critical current density of the HTSC compound YBa₂Cu₃O _y recovered at T = 920?C950°C after the low-temperature treatment have been investigated. At T = 200°C, structural defects are formed in a wet environment, which are capable of initiating pinning of magnetic vortices. A short-term (1?C3 h) recovery annealing performed at T = 930?C950°C leaves in the samples a fairly large amount of structural defects formed during the low-temperature treatment, which results in a substantial increase in the critical current density in magnetic fields of ??2 T as compared to the ceramics not subjected to double annealing. A longer high-temperature treatment removes the structural defects formed and brings the electrophysical properties of YBa₂Cu₃O _y to the level characteristic of the ceramics produced by standard technology.     

Preparation and investigation of composite SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> films

SiO₂-TiO₂ films [Si:Ti = 1:(0.06–2.3)] are obtained by the sol-gel method. The structural and photoluminescent properties of the films and powders heat-treated at different temperatures are studied. It is shown that after 700°C the composite consists of TiO₂ crystallites that are structurally similar to anatase and distributed in an amorphous SiO₂ matrix. The photoluminescence spectra have maxima at 450–500 nm. The photoluminescence intensity depends on the treatment temperature and TiO₂ content. __________ Translated from Zhurnal Prikladnoi Spektroskopii Vol. 74, No. 3, pp. 357–361, May–June, 2007.     

Structural and magnetic phase transitions in Pr<Subscript>0.15</Subscript>Sr<Subscript>0.85</Subscript>MnO<Subscript>3</Subscript> at high pressure

The crystal and magnetic structures of Pr_0.15Sr_0.85MnO₃ manganite have been studied by means of powder X-ray and neutron diffraction in the temperature range 10–400 K at high external pressures up to 55 and 4 GPa, respectively. A structural phase transition from cubic to tetragonal phase upon compression was observed, with large positive pressure coefficient of transition temperature dT _ct /dP = 28(2) K/GPa. The C-type antiferromagnetic (AFM) ground state is formed below T _N ≈ 260 K at ambient pressure. While at ambient pressure the structural and magnetic transition temperatures are close, T _ct ~ T _N , upon compression they become decoupled with T _N ≪ T _ct due to much weaker T _N pressure dependence with coefficient dT _N /dP = 3.8(1) K/GPa.     

Effect of double annealing on the critical parameters of highly textured YBa2Cu3O6.9

The effect of low-temperature treatment (200°C) and subsequent annealing at 930°C on the critical parameters of highly textured YBa₂Cu₃O_6.9 is studied. The structural defects that are formed during the low-temperature decomposition of this compound into phases with different oxygen contents and during interaction with atmospheric moisture are shown to deteriorate the superconducting properties. After annealing at T = 930°C and subsequent oxidation, superconductivity is restored and the formed defects are partly retained and serve as effective pinning centers, including the case of high magnetic fields. The stresses induced by the low-temperature treatment lead to primary recrystallization at T = 930°C, which results in the disappearance of texture and an isotropic state of the material in high fields.     

Pure and Sn-, Ga- and Mn-doped ZnO gas sensors working at different temperatures for formaldehyde,humidity, NH<Subscript>3</Subscript>, toluene and CO

ZnO and Sn-, Ga- and Mn-doped ZnO nanoparticles were prepared by a coprecipitation method, and characterized by scanning electron microscopy (SEM), energy dispersive spectra (EDS), X-ray diffraction (XRD) and Raman spectra. The gas sensing properties were studied using formaldehyde, relative humidity, NH₃, toluene and CO as the probes. The results show that all particles have wurtzite ZnO phase, though Sn–ZnO has a relatively smaller particle (and crystallite) size than the other three samples. Gas sensing property tests reveal that the temperature where the gas sensing maximum is gained (T _M) is changed by different dopants: Sn–ZnO and Mn–ZnO have relatively lower T _M (∼100°C lower) compared with that of pure ZnO, while Ga–ZnO has the same T _M as pure ZnO except in CO sensing. Thermoluminescence (TL) spectra were used to investigate the mechanism of T _M change. The peak positions of Ga–ZnO and ZnO are the same at 300–350°C, while that of Sn–ZnO shifts to 250–300°C, which might contribute to the same T _M of Ga–ZnO and pure ZnO and relatively lower T _M of Sn–ZnO. In the case of Mn–ZnO, the luminescence emission is evidently limited by its black color.     

Metal-insulator transition in a radiation-disordered La<Subscript>0.85</Subscript>Sr<Subscript>0.15</Subscript>MnO<Subscript>3</Subscript> manganite

The temperature dependences of the electrical resistivity ρ(T) and the ac magnetic susceptibility χ(T, H = 0) are thoroughly investigated for a perovskite-like lanthanum manganite, namely, La_0.85Sr_0.15MnO₃, which is preliminarily exposed to neutron irradiation with a fluence _F = 2 × 10¹⁹ cm^?2 and then annealed at different temperatures ranging from 200 to 1000°C. The results of the electrical resistance measurements demonstrate that neutron irradiation of the samples leads to the disappearance of the low-temperature insulating phase. As the annealing temperature increases, the insulating phase is not restored and the manganite undergoes a transformation into a metallic phase. Analysis of the magnetic properties shows that, under irradiation, the ferromagnet-paramagnet phase transition temperature T_C decreases and the magnetic susceptibility is reduced significantly. With an increase in the annealing temperature, the phase transition temperature T_C and magnetic susceptibility χ(_{T, H} = 0) increase and gradually approach values close to those for an unirradiated sample. This striking difference in the behavior of the electrical and magnetic properties of the radiation-disordered La_0.85Sr_0.15MnO₃ manganite is explained qualitatively.     

Ultra-sharp α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoflakes: growth mechanism and field-emission

We report the synthesis of single-crystalline α-Fe₂O₃ nanoflakes from a simple Fe–air reaction within the temperatures range of 260–400 °C. The nanoflakes synthesized at the lowest temperature (260 °C) in this work show an ultra-sharp morphology: 5–10 nm in thickness, 1–2 μm in length, 20 nm in base-width and around 5 nm at the tips; successfully demonstrate the promising electron field emission properties of a large-scaled α-Fe₂O₃ nanostructure film and exhibit the potential applications as future field-emission (FE) electron sources and displays (FEDs). The formation and growth of α-Fe₂O₃ nanostructures were discussed based on the surface diffusion mechanism. PACS 79.60.Jv; 79.70.+q; 77.84.Bw     

Nonlinear properties and paramagnet-to-ferromagnet transition in Nd<Subscript>0.7</Subscript>Ba<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript> single crystal with metallic ground state

We present the results from studying the magnetic properties (linear and nonlinear susceptibilities and the depolarization of polarized neutrons) of Nd_{1 − x} Ba _x MnO₃ manganite, x = 0.3, with Curie temperature T _C ≈ 140 K and dielectric-to-metal transition temperature T _DM ≈ 129 K. Its critical behavior corresponds to that of an isotropic 3-D ferromagnet at temperatures above T*≈ 144 K, but a strong nonlinear response in weak magnetic fields and depolarization are observed at temperatures below T*. It is shown that this nontraditional behavior is related to the generation of ferromagnetic clusters in the paramagnetic matrix that form a conducting percolative network at temperatures near T _DM.     

Anomalies of the specific heat near the quantum critical point in Tm<Subscript>0.74</Subscript>Yb<Subscript>0.26</Subscript>B<Subscript>12</Subscript>

The behavior of the specific heat near the quantum critical point x ∼ 0.3 in the Tm_{1 − x} Yb _x B₁₂ system has been studied. Detailed measurements have been performed on high-quality single-crystalline Tm_0.74Yb_0.26B₁₂ samples within a wide temperature range of 1.9–300 K in a magnetic field up to 9 T. The temperature dependence of the magnetic contribution to the specific heat has a logarithmic divergence of the form C/T ∼ lnT at T < 4 K, which can be attributed to the quantum critical behavior regime suppressed by the external magnetic field. The Schottky anomaly of the magnetic contribution to the specific heat in Tm_0.74Yb_0.26B₁₂ has been analyzed.     

Causes of the Metamagnetism in a Disordered EuMn<Subscript>0.5</Subscript>Co<Subscript>0.5</Subscript>O<Subscript>3</Subscript> Perovskite

The magnetic properties of the EuMn_0.5Co_0.5O₃ perovskite synthesized under various conditions are studied in fields up to 140 kOe. The sample synthesized at T = 1500°C is shown to exhibit a metamagnetic phase transition, which is irreversible below T = 40 K, and the sample synthesized at T = 1200°C demonstrates the field dependence of magnetization that is typical of a ferromagnet. Both samples have T_C = 123 K and approximately the same magnetization in high magnetic fields. The metamagnetism is assumed to be related to a transition from a noncollinear ferromagnetic phase to a collinear phase, and the presence of clusters with ordered Co²⁺ and Mn⁴⁺ ions leads to ferromagnetism. The noncollinear phase is formed due to the competition between positive Co²⁺–Mn⁴⁺ and negative Mn⁴⁺–Mn⁴⁺ and Co²⁺–Co²⁺ interactions, which make almost the same contributions, and to the existence of a high magnetic anisotropy.