壳聚糖的光度测定新方法

研究了以刚果红分光光度法测定壳聚糖,探讨了最佳实验条件及干扰因素的影响。在pH9．7时,刚果红和壳聚糖形成有色物质,检测波长为543．5nm,线性方程为：A=0．0200ρ＋0．0156,R^2=0．9978。在0～20．00μg／mL范围内呈现良好的线性关系,平均回收率为99．20％。采用该方法测定了两种复方样品中的壳聚糖,方法的选择性和灵敏度良好。该方法可用于检测复方样品中少量的壳聚糖。     

壳聚糖/明胶/TiO2三元复合膜的制备与功能特性

纳米TiO2用阴离子表面改性剂SDS改性后,以溶液共混法制备了壳聚糖／明胶/TiO2复合膜,用FTIR、XRD、SEM、TEM表征了其结构与形态,并测试了其吸水率、透光率、力学性能和抑菌性能。进而探讨了复合膜中明胶和纳米TiO2含量对壳聚糖膜性能的影响。结果表明：复合膜中,壳聚糖、明胶和TiO2微粒间存在强烈的氢键相互作用,从而使明胶与壳聚糖具有良好的相容性,TiO2与壳聚糖、明胶分子间有很好的界面作用。适量TiO2的加入,可使壳聚糖／明胶共混膜的力学性能得到改善,明胶质量分数为0．30时,掺杂wTiO2为0．01、0．02的复合膜较壳聚糖／明胶共混膜的湿强及干态韧性分别提高了55．9％,40．8％和49．7％,47．9％。此外,复合膜的抑菌性能随明胶的增加而降低,但随TiO2的掺杂比的增加而增强,纳米TiO2的引入拓宽了壳聚糖和明胶两种天然高分子材料的应用范围。     

溶菌酶降解壳聚糖条件的研究

研究了溶茵酶对壳聚糖的降解条件,结果表明：脱乙酰度约70％的壳聚糖较易被溶菌酶水解;水解反应的最适温度为55℃、pH值为4．0,低速摇床振荡对水解有利;在壳聚糖水解初期,溶液中还原糖浓度迅速增加,0．5h后水解速率逐渐减慢,至8h后还原糖浓度的增加已很缓慢;酶解液中还原糖的生成量瞳壳聚糖及溶茵酶浓度的增加而增大,当壳聚糖溶液浓度为20mg／mL、溶茵酶浓度为2．48mg／mL时,水解6h后,还原糖的含量可达6．758mmol／L。水解6h后酶解液中还原糖浓度与壳聚糖的浓度呈线性关系。     

控温下微波反应装置用于壳聚糖羧甲基化反应

微波加热近年来被广泛应用在化学合成中。本文报道了通过外接恒温槽的恒温循环水的方法，实现了微波反应系统的恒温控制。将该装置应用于壳聚糖的羧甲基化反应，采用水溶剂代替传统加热方法的异丙醇溶剂，制备出取代度达0．85的羧甲基壳聚糖。     

壳聚糖富集火焰原子吸收法测定水中痕量铜

采用壳聚糖修饰钨丝基质螺旋卷，直接浸入含有痕量铜的pH5．0的Brltton-Robinson缓冲溶液中，经电磁搅拌富集一定时间后，将其转移至空气／乙炔火焰燃烧器上，利用火焰原子吸收光谱法简便快速测定水中痕量铜。方法的线性范围为2—75μg／L；检出限为0．98μg／L。同一支钨丝螺旋卷重复涂敷壳聚糖富集Cu，RSD(n=6)为2．7％。     

硒化壳聚糖抑制人早幼粒白血病细胞增殖的研究

为探讨硒化壳聚糖对体外培养人早幼粒白血病细胞增殖的抑制作用,用SRB法和集落形成法检测了药物对细胞增殖的抑制作用,流式法检测了细胞周期阻断作用。结果表明,25、50、100mg／L硒化壳聚糖作用HL60细胞48h对细胞有增殖抑制作用（P〈0．01）;50、100mg／L硒化壳聚糖作用细胞48h后,G0／G1期细胞数较对照组增加了14．9％-22．0％（P〈0．05）,S期细胞减少了14．3％～20．1％（P〈0．05）。可见硒化壳聚糖对人早幼粒白血病细胞增殖具有抑制作用。     

粘度法研究壳聚糖与两性聚氨酯胶束间的相互作用

通过粘度法考察了壳聚糖(CS)在盐酸水溶液中与表面带有正电荷的两性聚氨酯(APU)胶束的相互作用，并研究了小分子盐浓度、pH及不同混合方式对复合体系粘度的影响．结果表明：在壳聚糖／APU盐酸混合体系中，较高浓度下APU胶束与壳聚糖分子间的静电斥力作用导致壳聚糖大分子链的伸展，使体系粘度提高，同时降低了壳聚糖溶液对电解质、pH的敏感性；不同混合过程导致壳聚糖大分子构像及其与APU组装、复合形态有很大差别，使混合体系流变性表现出明显的不同．     

邻苯二甲酰化壳聚糖中酰胺酸取代度的红外测定

室温条件下从完全脱乙酰化壳聚糖出发合成了不同酰胺酸取代度的邻苯二甲酰化壳聚糖，并以此为标样，标样的取代度由X射线光电子能谱（XPS）确定，研究了以FT－IR作为工具测定此系列衍生物的总取代度的方法，以2887cm^-1的吸收峰作为参比谱带，探针谱带可用1712cm^-1或749cm^-1的吸收峰，两种探针谱带所得曲线的斜率分别为1．13和0．12，相关系数分别为0．997和0．977，此结果表明：红外法是一种既准确可靠又方便可行的测定方法。     

粘度法预测聚乙二醇/壳聚糖体系的相容性

甲壳素在自然界的含量很大，仅次于纤维素，是一种颇具应用潜力的天然高分子．可由甲壳素经脱酸基化制得壳聚糖．由于其分子中存在氨基，因此能溶解干酸性水溶液中，并以聚电解质的形式存在，近来用壳聚糖制得的纤维膜应用于药物、食品等的分离和纯化、污水的处理，分离效果好，且不带入任何化学杂质．在壳聚糖纤维膜制作及与纤维的混纺过程中，都要探讨它与其它相应高聚物的相容性[1]．我们以相容的壳聚糖（chitosan）／聚乙二醇（PEG）体系为例，采用粘度法讨论其分子间的相互作用，并预测它们的相容性．壳聚糖的基本结构为1实验部分1.1…     

羧甲基壳聚糖/明胶共混膜的结构表征与吸湿保湿性

壳聚糖通过羧甲基化得到水溶性N，O-羧甲基壳聚糖，并将其配制成4Wt％水溶液，与4Wt％明胶水溶液共混，成功制得了羧甲基壳聚糖／明胶共混膜。采用红外光谱、x射线衍射、扫描电镜对共混膜进行结构表征，结果表明，共混膜中羧甲基壳聚糖和明胶分子间存在着较强的相互作用及良好的相容性。通过共混膜的力学性能测试，发现当羧甲基壳聚糖含量为20％时，共混膜的抗张强度达到最大值(75MPa)，分别比单独的羧甲基壳聚糖(45MPa)和明胶(43MPa)提高了66．7％和74％。经过吸湿和保湿性能测试，发现当羧甲基壳聚糖含量为80％时，吸湿率和保湿率分别为33．4％和69．2％，比单独的明胶膜分别提高了1．8倍和2．1倍。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.