双层板腔结构声传输及其有源控制研究

利用子系统模态综合方法,结合阻抗-导纳矩阵法,建立了双层板腔结构向自由空间声传输及其在入射板PZT控制、辐射板PZT控制,和腔中次级声源作动等多种控制策略下,系统物理模型的统一的分析模型,导出了系统模态响应及最优次级源强度的统一的阻抗-导纳矩阵表达式。该模型表达式各部分物理意义清晰、明确,便于进行系统耦合理论、有源控制及其机理的分析和数值研究。然后,在此基础上对双层板腔结构声传输有源控制进行了全面深入的数值计算和分析研究,重点探讨了控制方法策略及系统参数对有源控制效果的影响及其对应的控制机理。结果表明:入射板PZT作动辐射声功率最小控制策略是通过入射板、声腔和辐射板三个子系统的模态抑制或重组达到消声的目的,涉及多种复杂控制机理,对入射板、辐射板和声腔模态均有效,但对入射板模态更有效;在低频段声腔(0,0,0)模态在系统耦合响应中起主导作用,因此利用腔中次级声源作动能获得较理想的控制效果,是一种较好的控制策略;由于声腔模态与结构模态间复杂的耦合关系,使得某些频率处腔中声势能一定程度上的降低并不一定导致系统声传输损失的增加,因此,腔中声势能最小控制策略不一定能够获得理想的声传输控制效果。      

矩形封闭声腔壁板轻量化对声固耦合特性的影响

基于模态耦合法建立了考虑对侧柔性壁板的矩形封闭腔体声固耦合模型,导出了耦合系统声振响应随柔性板材料属性及厚度变化的近似关系.通过数值仿真计算,详细分析了单柔性板-单侧激励、双柔性板-双侧激励及双柔性板-单侧激励三种情况下板的轻量化设计对系统声固耦合特性及腔内声压响应的影响.结果表明:对于单柔性板-单侧激励及双柔性板-双侧激励情况,低频段腔内声压主要取决于板厚,其次是杨氏模量,而与板密度关系较弱.因此使用适当增厚的轻质板可以同时达到减重和低频区降噪的目标.对于双柔性板-单侧激励情况,适当的轻量化设计可以显著增强两板间低频段振动的耦合,从而降低该频段的声腔模态响应及腔内噪音.在中高频段,增加板厚和材料密度对降低三种情况的腔内声压均有利。      

Comparison of various decentralised structural and cavity feedback control strategies for transmitted noise reduction through a double panel structure

This paper compares various decentralised control strategies, including structural and acoustic actuator–sensor configuration designs, to reduce noise transmission through a double panel structure. The comparison is based on identical control stability indexes. The double panel structure consists of two panels with air in between and offers the advantages of low sound transmission at high frequencies, low heat transmission, and low weight. The double panel structure is widely used, such as in the aerospace and automotive industries. Nevertheless, the resonance of the cavity and the poor sound transmission loss at low frequencies limit the double panel's noise control performance. Applying active structural acoustic control to the panels or active noise control to the cavity has been discussed in many papers. In this paper, the resonances of the panels and the cavity are considered simultaneously to further reduce the transmitted noise through an existing double panel structure. A structural–acoustic coupled model is developed to investigate and compare various structural control and cavity control methods. Numerical analysis and real-time control results show that structural control should be applied to both panels. Three types of cavity control sources are presented and compared. The results indicate that the largest noise reduction is obtained with cavity control by loudspeakers modified to operate as incident pressure sources.     

An indirect hybrid sound transmission loss controller

The control of sound transmission through panels is an important noise control problem in the aerospace, aeronautical, and automotive industries. The trend towards using lightweight composite materials that have lower sound insulation performance is a negative factor regarding low frequency transmission loss. Double-panel partitions with the gap filled with sound absorption materials are often employed to improve the sound insulation performance with reduced added weight penalty. However, in the low frequency range, the strong coupling between the panels through the air cavity and mechanical paths may greatly reduce the sound transmission performance, making it even lower than the performance of a single panel in some frequency ranges. In this work, an experimental investigation of a new kind of hybrid (active/passive) acoustic actuator is presented. The idea consists of replacing the acoustic absorption material by a hybrid actuator aiming at improving the transmission loss at low frequencies without altering the passive attenuation. A prototype of the system is tested in a plane wave acoustic tube setup. Different kinds of SISO feedforward control implementations were used to attenuate the sound power transmitted through the hybrid active–passive panel using an error microphone or a particle velocity sensor placed downstream with respect to the sample panel. Measurement results of the transmission loss with active and hybrid attenuation are presented and discussed.     

Vibro-acoustic analysis of a rectangular-like cavity with a tilted wall

In this paper, a fully coupled vibro-acoustic model is developed to characterize the structural and acoustic coupling of a flexible panel backed by a rectangular-like cavity with a slight geometrical distortion, which is introduced through a tilted wall. The combined integro-modal approach is used to handle the acoustic pressure inside the irregular-shaped cavity. Based on the model proposed, the distortion effect on the vibro-acoustic behavior of the coupled system is investigated using the averaged sound pressure level inside the enclosure and the averaged quadratic velocity of the vibrating plate. Simulations are conducted to examine the distortion effect on acoustic natural frequencies, acoustic pressures and structural responses. Effects of the wall inclination on coupling coefficients are also assessed, and an index is proposed to quantify the degree of variation of coupling strength.     

Eigenpairs of a coupled rectangular cavity and its fundamental properties

This paper deals with the eigenvalue problem of a coupled rectangular cavity comprising five rigid walls and one flexible panel frequently employed in much literature. It is the purpose of this paper to derive explicitly the eigenpairs of the coupled cavity, which are yet to be found. First, the coupling orthogonality conditions the eigenpairs need to satisfy are derived, thereby enabling the verification of the eigenpairs newly sought or already existent. Using the coupling orthogonality conditions, the modal equation of the coupled cavity system is then obtained, permitting one to deal with a forced response of the coupled cavity. It is shown that the eigenfunctions governing the dynamics of the sound field are expressed as the infinite sum of degenerate eigenfunctions. The characteristic matrix equation is then derived, specifying the eigenpairs of the coupled cavity. In order to investigate the fundamental properties of the eigenpairs derived, a numerical analysis is conducted, revealing the presence of evanescent modes in addition to the conventional standing wave modes. Finally, an experiment is carried out, verifying the validity of the eigenpairs derived in the article.     

平板扬声器用于结构声有源噪声控制实验研究

对NXT技术的分布式平板扬声器和集中参数扬声器的频响和指向性等进行了对比测量，通过对组合平板扬声器的声场研究及有源消声实验，证明了平板扬声器用于有源噪声控制的可行性。综合平板扬声器和集中参数扬声器的物理特点和声场特性，根据基于平面声源有源噪声控制的已有的理论研究结果和本文的实验结果，可以认为，NXT平板扬声器适合作有源噪声控制的次级源，有利于有源噪声控制的工程推广应用。     

穿孔率和穿孔直径耦合下微穿孔板吸声体整体吸声性能

微穿孔板几何参数的耦合性及其对整体吸声性能的影响,对于设计微穿孔板吸声体和优化其工作性能具有指导作用.根据微穿孔板吸声体基本理论,研究了穿孔率和穿孔直径双参数耦合作用下微穿孔板吸声体的整体吸声性能.穿孔率和穿孔直径之间的耦合性与其本身取值密切相关,而与板厚和板后腔深无明显关系;在穿孔率-穿孔直径参数域上,吸声体存在吸声...     

Vibro-acoustic analysis of a rectangular cavity bounded by a flexible panel with elastically restrained edges

A coupled system consisting of an acoustic cavity and an elastic panel is a classical problem in structural acoustics and is typically analyzed using modal approaches based on in vacuo structural modes and the rigidly walled acoustic modes which are pre-determined based on separate component models. Such modeling techniques, however, tend to suffer the following drawbacks or limitations: (a) a panel is only subjected to ideal boundary conditions such as the simply supported, (b) the coupling between the cavity and panel is considered weak, and (c) the particle velocity cannot be correctly predicted from the pressure gradient on the contacting interface, to name a few. Motivated by removing these restrictions, this paper presents a general method for the vibro-acoustic analysis of a three-dimensional (3D) acoustic cavity bounded by a flexible panel with general elastically restrained boundary conditions. The displacement of the plate and the sound pressure in the cavity are constructed in the forms of standard two-dimensional and 3D Fourier cosine series supplemented by several terms introduced to ensure and accelerate the convergence of the series expansions. The unknown expansions coefficients are treated as the generalized coordinates and determined using the Rayleigh-Ritz procedure based on the energy expressions for the coupled structural acoustic system. The accuracy and effectiveness of the proposed method are demonstrated through numerical examples and comparisons with the results available in the literature.     

Analytical research on structural-acoustic coupling of a cavity surrounded by flexible panel

The structural-acoustic coupling characteristics, mechanisms, effect of structural-acoustic coupling on natural mode and natural frequencies of the system are analyzed theoretically and numerically. Formulae for the natural frequencies of the coupled system are derived. Some new conclusions are obtained. Analytical results demonstrate that the strongly coupled system indicates obvious closed-loop feedback characteristics, whereas the weakly coupled system indicates obvious feedforward characteristics, and it is because of the presence of the feedback loop that the natural characteristics and natural frequencies are changed. Cluster coupling characteristic between the structural and acoustic modes for the regular cavity and panel system is found, which determines the coupling interaction between the flexible panel and cavity. Any mode in one mode cluster only interferes the modes and the modal natural frequencies in the same cluster independently. The modal cluster coupling changes not only the natural frequencies of the system but also the modal order and structural mode shape.     

量子点腔非谐振耦合系统纯退相干的特性及应用

采用非相干泵浦、受激辐射和纯退相干的量子主方程研究了量子点腔耦合系统,得出腔与量子点发射光谱解析解.理论分析显示,在非谐振耦合系统中纯退相干能使腔发射谱产生明显的移位效应,从而可以解释“非谐振耦合腔有效发射”效应.为了进一步研究纯退相干在量子点腔耦合系统上的应用,引入了系统有效耦合率和单光子源效率,并通过比较有效耦合率与腔耗散定义出好腔与坏腔机制.选取两组依据实验数据作为参量,在共振与失谐时研究了纯退相干对系统有效耦合率和单光子源效率的影响.结果表明:纯退相干可提高失谐系统有效耦合率与单光子源效率,从而可能使坏腔转变为好腔|两组参量中有较大耦合效率一组在一定范围内满足好腔机制,其单光子源效率明显优于另一组.在非谐振耦合系统比较了好腔机制与坏腔机制的激光,好腔机制是实现单量子点激光的必要条件|由于非谐振耦合系统Fano因子无最大值出现,从而该系统可能无激光阈值.     

基于平面声源的三层有源隔声结构物理机制研究

次级源为平面声源的三层有源隔声结构,深入理解有源隔声的物理机理有助于挖掘降噪潜力及实现系统优化设计。首先对三层有源隔声结构建模并求解系统的振动响应。然后,对控制前三层结构中声能量的传输规律进行深入分析。最后,在辐射板声功率最小条件下,通过分析控制前后声能量传输特性的变化阐述了隔声的物理机理。结果表明,声能量在三层结构中传输形成四个等效的传输通道,中间板与两腔的作用类似带通滤波器,不同的传输通道具有相似的带通特性。有源隔声机理在于,通过控制抑制了通带内的能量传输,显著提高了三层结构整体的隔声性能,从而有效阻止了声波的向后传播。      

Virtual sensors for active noise control in acoustic-structural coupled enclosures using structural sensing: part II--Optimization of structural sensor placement

The work proposed an optimization approach for structural sensor placement to improve the performance of vibro-acoustic virtual sensor for active noise control applications. The vibro-acoustic virtual sensor was designed to estimate the interior sound pressure of an acoustic-structural coupled enclosure using structural sensors. A spectral-spatial performance metric was proposed, which was used to quantify the averaged structural sensor output energy of a vibro-acoustic system excited by a spatially varying point source. It was shown that (i) the overall virtual sensing error energy was contributed additively by the modal virtual sensing error and the measurement noise energy; (ii) each of the modal virtual sensing error system was contributed by both the modal observability levels for the structural sensing and the target acoustic virtual sensing; and further (iii) the strength of each modal observability level was influenced by the modal coupling and resonance frequencies of the associated uncoupled structural/cavity modes. An optimal design of structural sensor placement was proposed to achieve sufficiently high modal observability levels for certain important panel- and cavity-controlled modes. Numerical analysis on a panel-cavity system demonstrated the importance of structural sensor placement on virtual sensing and active noise control performance, particularly for cavity-controlled modes.     

Computational studies of steady-state sound field and reverberant sound decay in a system of two coupled rooms

The acoustical properties of an irregularly shaped room consisting of two connected rectangular subrooms were studied. An eigenmode method supported by a numerical implementation has been used to predict acoustic characteristics of the coupled system, such as the distribution of the sound pressure in steady-state and the reverberation time. In the theoretical model a low-frequency limit was considered. In this case the eigenmodes are lightly damped, thusthey were approximated by normal acoustic modes of a hard-walled room. The eigenfunctions and eigenfrequencies were computed numerically via application of a forced oscillator method with a finite difference algorithm. The influence of coupling between subrooms on acoustic parameters of the enclosure was demonstrated in numerical simulations where different distributions of absorbing materials on the walls of the subrooms and various positions of the sound source were assumed. Calculation results have shown that for large differences in the absorption coefficient in the subrooms the effect of modal localization contributes to peaks of RMS pressure in steady-state and a large increase in the reverberation time.      

Analysis of structural - acoustic coupling of elastic rectangular enclosure with arbitrary boundary conditions

The structural acoustic coupling characteristics of a rectangular enclosure con- sisting of two elastic supported flexible plates and four rigid plates are analyzed.A general formulation considering the full coupling between the plates and cavity is developed by using Hamiltonian function and Rayleigh-Ritz method.By means of continuous distributions of ar- tificial springs along boundary of flexible plates,a wide variety of boundary conditions and structure joint conditions are considered.To demonstrate the validity of the analytical model, the responses of sound pressure in the cavity and plate velocity are worked out.The analytical results coincides well with Kim's experimental results.The result is satisfactory.Finally,an- alytical results on the structure vibration and the sound field inside the cavity are presented. These results indicate that the coupling of the combined structure is relatively weak,so the internal cavity sound is controlled by plate directly excited,and the translational stiffness affects the sound more than the rotational stiffness does.     

双层加筋板低频声的隔离与有源控制

为探讨加筋对双层结构低频隔声及有源控制的影响,分析了筋条数目及布放位置对双层加筋结构低频隔声性能、有源控制策略选取及有源隔声性能的影响。首先利用模态叠加与声-振耦合理论对双层加筋结构建模,然后采用数值算例对上述问题展开探讨。研究发现,筋条数目增多或筋条靠近基板的中间位置布放,将有利于双层加筋结构低频隔声性能的提高。对于有源控制措施,声控制策略与力控制策略相比,前者的控制效率较高且降噪效果较好。由于筋复杂的耦合影响,添加多条筋或筋条靠基板中间布置时有源控制效果减弱,需施加多个点源才能获得较好的降噪效果。      

微穿孔板复合板型声学超材料的低频吸声

针对单层微穿孔板的低频吸声问题提出了微穿孔板复合板型声学超材料结构。将板型声学超材料置入微穿孔板结构的背腔内部实现结构复合。实验结果表明:在相同背腔厚度下,复合结构的吸声性能整体优于单层微穿孔板结构,其中复合结构的吸声曲线从396~892 Hz均大于0.6,在453 Hz处吸声系数达到0.972。利用有限元方法对复合结构进行了仿真,仿真计算的吸声曲线与实验吸声曲线的趋势基本相同,同时发现低频吸声主要由板型声学超材料与声波相互作用贡献。板型声学超材料的吸声峰值的对应频率处,其等效动态质量密度从正变负。在复合结构内部的微穿孔板和板型声学超材料存在相互耦合作用,使得复合结构的第一峰值发生微小偏移。增加板型声学超材料的质量块重量可以使第一吸声峰值向低频移动;保持总背腔厚度不变,增加板型声学超材料的子腔厚度,也可以使第一吸声峰向低频移动。      

基于声辐射模态的有源结构声传入及其辐射控制

从辐射模态的概念和角度研究利用结构误差传感方法对弹性封闭空间结构声辐射进行传感和有源控制。首先分析了辐射模态的数学和物理意义并揭示了辐射模态与声腔模态之间的内在耦合关系。通过声辐射模态建立了弹性封闭空间结构声辐射传感和有源控制模型,并提出了通过传感器阵列测量结构表面有限点的振速分布和设计特定的辐射模态空间滤波器来获得控制所需的误差信号。在此基础上对封闭空间结构声辐射有源控制和误差传感策略进行了深入的理论和数值仿真分析,重点讨论了传感器的数量和布放对辐射模态传感及其有源控制效果的影响。结果表明:辐射模态与声腔模态的耦合具有严格的选择性,各阶辐射模态的形状和与相耦合的主导声模态在耦合面上的形状非常相似;利用结构传感技术传感封闭空间的辐射模态时测点不足或空间采样不足将可能产生较严重的模态泄漏问题,使得不希望的结构模态泄露进所测的辐射模态当中来。在低频范围内,一般只需传感并最小化前三阶有效辐射模态声势能,在更低频和空间声模态频率附近,只需最小化前一阶最有效辐射模态声势能,便能和总声势能最小化策略控制效果基本一样。      

Acoustoelasticity: General theory,acoustic natural modes and forced response to sinusoidal excitation,including comparisons with experiment

A comprehensive theoretical model has been developed for interior sound fields which are created by flexible wall motion resulting from exterior sound fields. Full coupling between the wall and interior acoustic cavity is permitted. An efficient computational method is used to determine acoustic natural frequencies of multiply connected cavities. Simplified formulae are developed for interior sound levels in terms of cavity, wall and external acoustic field parameters. Comparisons of theory and experiment show generally good agreement.