羧甲基纤维素-壳聚糖水凝胶球的制备及性能

采用物理交联法制备了羧甲基纤维素(CMC)-壳聚糖(CS)共混水凝胶球;研究了共混球的耐酸碱性、溶胀性及对亚甲基蓝的吸附性能.结果表明,水凝胶球在弱酸和弱碱中具有一定的稳定性;随着羧甲基纤维素与壳聚糖质量比的增大,水凝胶的吸水溶胀率增加.在CMC与CS质量比为1∶4时制备的水凝胶呈规则球状.     

新型黄原酸壳聚糖对铅离子的吸附及机理研究

以壳聚糖为原料,先合成O-羧甲基壳聚糖,再和二硫化碳反应制备出新型黄原酸壳聚糖,使用元素分析、FT-IR、UV和TG对其结构进行表征。比较了壳聚糖、O-羧甲基壳聚糖和黄原酸壳聚糖对铅离子的吸附能力,并研究黄原酸壳聚糖对水溶液中铅离子的吸附性能,探讨了铅离子溶液的pH值对吸附的影响和黄原酸壳聚糖对铅离子的吸附热力学。结果表明,黄原酸壳聚糖对铅离子吸附量是壳聚糖的8.37倍,平衡吸附量可达600.6mg/g。XPS表明,吸附过程主要通过吸附剂中的氨基、羧基和黄原酸基团与铅离子发生作用完成。     

离子凝胶反应法制备壳聚糖/N,O-羧甲基壳聚糖微球

以一氯乙酸与壳聚糖反应形成N,O-羧甲基壳聚糖两性聚电解质,分光光度法测定其等电点IEP=2．86。以此两性聚电解质与壳聚糖可以在一定条件下形成微球,光学显微镜和电子显微镜测试表明,控制两种聚电解质配比可以制备不同粒径大小的微球,而超声功率对微球粒径的影响较小。红外光谱测试表明微球中N,O-羧甲基壳聚糖羧基以羧酸根形式存在,分光光度与电导法联合测定表明两种聚电解质以离子凝胶作用形成微球,其最佳制备条件为IEP（CM-CHITOSAN）〈pH〈pKa（CS）,在此较宽的pH值范围内微球可稳定存在。     

海藻酸盐/壳聚糖衍生物复合抗菌纤维

通过溶液纺丝法制备海藻酸盐/羧甲基壳聚糖（CMC）共混纤维,并用红外光谱,X射线衍射和扫描电镜对共混纤维进行了表征.结果表明：共混体系中的两种组分之间存在着较强的相互作用,有良好的相容性.当ωCMC=0.30时,共混纤维的干态抗张强度达到最大值,13.8cN/tex.当ωCMC=0.10时,纤维的干态断裂伸长率可达23.1%.纤维的湿态抗张强度和断裂伸长率随着CMC含量的增加而降低.CMC的引入,可显著提高纤维的吸水率.用壳聚糖季铵盐对纤维进行处理,可赋予纤维抗菌性.     

磁性壳聚糖微球的制备及对Cr(Ⅵ)的吸附性能研究

用壳聚糖包埋磁流体,用戊二醛交联制成磁性壳聚糖微球,并用红外光谱表征其结构。用制备的磁性壳聚糖微球吸附Cr(Ⅵ)离子,考察了其对Cr(Ⅵ)离子的吸附性能;探讨了吸附时间、溶液pH值、吸附剂用量、温度、Cr(Ⅵ)起始浓度以及其他离子存在对Cr(Ⅵ)离子去除率的影响。实验结果表明,磁性壳聚糖微球吸附Cr(Ⅵ)离子的最佳条件为:吸附平衡时间40 min,最佳吸附pH值6左右,磁性壳聚糖微球用量10 mg,温度升高有利于提高磁性壳聚糖微球的吸附效率,Cr(Ⅵ)离子起始质量浓度为12μg/mL,无机盐的存在引起磁性壳聚糖微球的吸附性能降低。并且考察了吸附剂的再生性能,实验结果表明磁性壳聚糖微球具有良好的重复使用性。     

改性壳聚糖膜用于醇水混合液分离的研究(Ⅱ)─壳聚糖－羧甲基纤维素共混物膜

制备了壳聚糖(CS)─羧甲基纤维素(CMC)共混物膜(I-2),对其成膜反应、溶胀度、交联度及拉伸强度进行了研究,结果表明,壳聚糖与羧甲基纤维素共混物在成膜的同时还发生交联反应;当CS/CMC=1时,交联度最大,此时共混物膜不溶于稀醋酸水溶液。首次将此共混物膜用于乙醇/水混合液的分离,该膜具有优良的醇水分离性能,当CS/CMC=1时,渗透通量和分离因子皆达到最大值[J=0.9kg/(m²·h),a=800,90wt%乙醇,45℃],且该膜的分离因子基本上不随温度变化,醇水透过I-2膜的表现活化能△E为32.6kJ/mol.对CS/CMC2+2+2+2+次序递增,分离因子变化次序则刚好相反。     

3-N-乙酰基-2-取代芳基-5-[5''-甲基-异噁唑-3'']-Δ3-1,3,4－噁唑啉类化合物的合成

保护氨基的壳聚糖微球经环氧氯丙烷交联得到不溶于酸的吸附剂，与氯乙酸在碱性条件下反应，合成了羧甲基壳聚糖树脂，并用FT-IR对树脂进行了表征。其吸附Pb^2 的实验结果表明，在1h内有最快的吸附速率，吸附受pH值影响。在pH=5时，对Pb^2 的吸附量为1．12mmol／g，比壳聚糖树脂提高了70％。     

交联羧甲基壳聚糖对铅离子的吸附研究

以壳聚糖为原料,先在氨基上引入羧甲基制备出N-羧甲基壳聚糖,再和环氧氯丙烷发生交联反应,合成出新型交联羧甲基壳聚糖,FTIR表征其结构。研究了交联羧甲基壳聚糖对Pb2+的吸附性能,探讨了交联剂用量、铅离子溶液的pH值、温度、吸附时间等因素对其吸附性能的影响,并考察了交联羧甲基壳聚糖对铅离子吸附动力学和热力学实验。实验结果表明,交联羧甲基壳聚糖对铅离子的吸附量优于壳聚糖,平衡吸附量可达297.6 mg/g。交联羧甲基壳聚糖对铅离子的吸附符合准二级动力学模型和Langmuier等温吸附,吸附主要依靠结构中的羧基和氨基基团。     

离子凝聚法制备负载流感疫苗的壳聚糖微球

采用三聚磷酸钠(TPP)作为离子交联剂, 应用离子凝聚法制备负载流感疫苗的壳聚糖微球. 筛选出壳聚糖起始质量分数为1%. TPP的浓度对壳聚糖微球的制备影响较大, 采用低浓度的TPP(200 μg/mL)制备的微球放置过夜均出现沉淀现象, 高浓度的TPP(800 μg/mL)在制备过程中出现絮状沉淀. 固化比影响微球的释放行为, 固化比为1∶1的微球爆炸式释放率达到90％, 固化比为1∶3的微球6 h后逐步释放, 12 h后释放率达到95％. 固化比为1∶5的微球6 h后没有明显的释放行为. 壳聚糖溶液的pH对微球的制备和释放没有显著的影响. 通过对负载流感疫苗的壳聚糖微球的制备条件和释放行为的研究结果表明, pH=5.6的壳聚糖溶液, 固化比为1∶3, TPP的质量浓度为400 μg/mL是较理想的流感疫苗壳聚糖微球的制备条件.     

壳聚糖微球负载的己二胺型聚酰胺-胺树状大分子的制备及对胆红素的吸附

通过反相悬浮反应制备了戊二醛交联的壳聚糖微球。以所制备的壳聚糖微球为载体,合成了己二胺型低代数聚酰胺-胺（Polyamidoamine,简称PAMAM）树枝状大分子（Genaration≤3）。考察了该微球在生理条件下对水溶液中胆红素的吸附行为,以及溶液的pH值,离子强度,温度,胆红素初始浓度,牛血清白蛋白等因素对吸附的影响。结果表明,吸附剂对胆红素具有良好的吸附性能,CS-G2.0,CS-G3.0,CS-G1.0,CS-G0和CS微球的平衡吸附率分别为94.61%,93.44%,92.97%,86.47%,52.38%,CS-G1.0-G3.0微球在0.5h吸附率已经超过70%,1h基本接近平衡,对胆红素的吸附量高达42.78mg/g。     

海藻酸-壳聚糖-海藻酸离子取代凝胶改性研究

羧甲基壳聚糖;微胶囊;海藻酸-壳聚糖-海藻酸离子取代凝胶改性研究     

Biosorption of beryllium from aqueous solutions onto modified chitosan resin: Equilibrium,kinetic and thermodynamic study

The goal of the present work is the recovery of beryllium ion from their solution by modified chitosan hydrogel. Chitosan was chemically cross-linked with glutaraldehyde to prevent its dissolution in aqueous acidic solutions. The obtained chitosan/glutaraldehyde adsorbent was reacted with chloroacetic acid to produce carboxymethyl chitosan (CMC), which was converted into sodium form by reaction with sodium hydroxide solution to increase its hydrophilic properties. The chemically synthesized chitosan adsorbent contains carboxylate group that expected to have a strong affinity to beryllium ions according to the hard-soft acid-base concept by Pearson because that beryllium ion is a hard acid and has smaller ionic radii. The synthesized adsorbent was characterized and its affinity towards beryllium ions was tested. The different experimental parameters including pH, beryllium concentration, agitation period and temperature were studied to optimize the biosorption process. The maximum biosorption values of beryllium species on the investigated biosorbent are 44.96 and 36.72?mg/g at pH 1 and 5, respectively. Kinetics and thermodynamic parameters of the biosorption process were evaluated from kinetic and biosorption experiments. The adsorbed beryllium species were eluted with a 3?M H₂SO₄ solution.     

Metal adsorption of carboxymethyl cellulose/carboxymethyl chitosan blend hydrogels prepared by Gamma irradiation

Blend hydrogels based on the carboxymethyl cellulose (CMC) and carboxymethyl chitosan (CMCts) were prepared by γ-irradiation of a high concentrated CMC/CMCts aqueous solution. Properties of the hydrogels, such as gel fraction, swelling ratio, gel strength, and metal adsorption for Pb and Au were investigated. The gel fraction increased with increasing dose, while the swelling ratio decreased with increasing it. The obtained blend hydrogels had high adsorption performance which was controlled by adjusting the composition of CMC/CMCts.     

Chondroitin Sulfate Fluorescence Biosensor Based on Graphere Quantum Dots Aggregating on CMC/CS Polyelectrolyte Microspheres

Here, we report an efficient fluorescence biosensor for chondroitin sulfate(CHS) based on polyelectrolyte microspheres of carboxymethyl cellulose(CMC) and chitosan(CS) composites inducing the aggregation of graphene quantum dots(GQDs), calling CMC/CS-GQDs. The polyelectrolyte microspheres(CMC/CS microspheres) were fabricated by using anioniccationic electrostatic attraction between CMC and CS by high voltage electrostatic spray technology. The aggregating process of GQDs was based on the anionic-cationic electrostatic attraction as well. After combing with the polyelectrolyte microspheres, the fluorescence of GQDs disappeared. CHS, which widely consists in the cell surface of human beings and animals, carries a large number of negative charges on the surface. The addition of CHS enabled CHS and GQDs to compete with each other to composite with the CMC/CS microshpheres. As a result of the higher surface charge density of CHS, CMC/CS-CHS formed accompanied by the release of GQDs, and the fluorescence of the system recovered. The CHS content was detected by analyzing the system's fluorescence recovery, which suggested that the obtained fluorescence biosensor can accurately detect the concentration of CHS. The test results showed that the linear range of the fluorescence recovery for this biosensor with respect to CHS was 0~12.00 mg/mL, and the detection limit was 10-8 M. Besides, to test the stability of the biosensor, the CMC/CS-GQDs micropsheres persisted for one month, with a low fluorescence quenching of 9.48%. These results suggested that CMC/CS-GQDs can be utilized as efficient fluorescence biosensor for the detection of CHS. Moreover, the detection method was simple and efficient, and could be widely popularized.     

The Preparation of Functionalized Crosslinked Macroporous Chitosan Microspheres and their Adsorption Properties for Bilirubin

Summary: glutaraldehyde cross-linked macroporous chitosan microspheres (CS) were prepared by inverse phase suspension reaction with sugar as porogenic agent. The microspheres were modified with different reagents of 1, 6 hexanediamine (HDA) and low generation polyamidoamine (PAMAM) dendrimers including PAMAM G1.0, PAMAM G2.0, PAMAM G3.0. The content of amino groups on CS, CS-PAMAM G1.0, CS-PAMAM G2.0, CS-PAMAM G3.0, CS-HDA was 3.56, 5.10, 5.47, 6.47, 4.66 mmol/g, respectively. The bilirubin adsorption on the above five microspheres was carried out in 0.05M phosphate buffer solution (pH = 7.2–7.4) at 37 °C. The results indicated all the modified CS microspheres were better than unmodified CS microspheres for bilirubin adsorption. CS-HDA has the best adsorption property even if the content of the amino groups was not very high.     

二异丁胺修饰的天然壳聚糖磁性微球与铼的吸附行为

以生物质废弃物螃蟹壳为原料,通过简单的化学处理制成磁性微球,再经二异丁胺(DIBA)修饰合成了生物质吸附剂FCS-DIBA[FCS:Fe3O4与壳聚糖(CS)复合微球]。 FCS-DIBA对Re(Ⅶ)具有很高的吸附选择性,最大吸附量可达185 mg/g,而且不受环境酸度的影响,在pH=2条件下可实现Re(Ⅶ)与Cu(Ⅱ)、Zn(Ⅱ)、Mn(Ⅶ)和Fe(Ⅲ)等常见共存金属离子的分离,该吸附等温线符合Langmuir方程。 此外,对FCS-DIBA吸附铼的机制和吸附稳定性能等进行了探讨。