茜素红S/多壁碳纳米管修饰碳糊电极阳极溶出伏安法测定痕量铜

制备了茜素红S/多壁碳纳米管修饰碳糊电极,提出了一种灵敏的溶出伏安法测定痕量铜的新方法.在极谱分析仪上采用二阶导数线性扫描伏安法进行分析,在0.1 moL/L的HAc-NaAc缓冲溶液(pH 4.1)中,Cu与修饰电极表面的茜素红S(ARS)形成Cu(Ⅱ)-ARS络合物而富集于电极表面,于-400 mV处还原后,再进行阳极化扫描,于64 mV处获得一灵敏的铜的阳极溶出峰,峰电流与Cu(Ⅱ)浓度在2×10-11 mol/L～6×10-7 mol/L范围内呈良好的线性关系,检出限(S/N=3) 为8.0×10-12 mol/L(富集时间240 s).方法应用于人发中铜含量的测定,回收率为98%～102%.     

丁二酮肟修饰碳糊电极阳极溶出伏安法测定痕量铋

报道了用丁二酮肟修饰碳糊电极测定微量铋的电分析方法。Bi~(3+)通过与电极表面的丁二酮肟作用而富集在电极表面,同时在-0.40 V(vs.SCE)还原成零价,当电极电势从-0.40 V向0.40 V扫描时,被还原的铋从电极表面溶出,在0.03 V出现一个十分灵敏的阳极溶出峰。优化了各种实验参数,如支持电解质的选择及pH值、丁二酮肟的用量、富集电位及时间等。修饰电极测定铋的线性范围为1×10~(-9)～1×10~(-6)mol/L。富集6 min后检出限可达4×10~(-10)mol/L。该方法简便快速,灵敏度高,分析成本低廉,并成功应用于实际水样中微量铋的测定。     

碳纤维束电极差分脉冲阳极溶出伏安法测定矿物中微量金

本文提出碳纤维束电极差分脉冲阳极溶出伏安法直接测定矿物中微量金的方法。较深入地讨论了活化时间,Hg/Au(W/W)对电极响应灵敏度和稳定性的影响,以及富集电位和时间的影响。富集3min,检测下限0.07μg/L;线性范围0.07～30μg/L,测定结果与AAS法基本相符。     

双硫腙修饰玻碳电极阳极溶出伏安法测定痕量镉和铅

报道了双硫腙修饰玻碳电极同时测定痕量镉和铅的电分析方法。镉和铅离子通过与电极表面的双硫腙发生螯合作用而富集在电极表面 ,同时在 -1 .2 0V(vs.SCE)还原成零价镉和铅 ,当电极电势从 -1 .2 0V向 -0 .3 0V扫描时 ,被还原的镉和铅从电极表面溶出 ,分别于 -0 .78V和 -0 .4 8V左右形成灵敏的阳极溶出峰。优化了支持电解质及pH值、双硫腙用量、富集电位及时间等实验参数。利用该修饰电极测定镉、铅的线性范围分别为 1 .0×1 0 - 8～ 2 .5× 1 0 - 6 mol L和 5 .0× 1 0 - 9～ 2 .5× 1 0 - 6 mol L。检测限分别为 5 .0× 1 0 - 9mol L和7.0× 1 0 - 1 0 mol L。该法用于实际水样中镉和铅的测定 ,平均回收率分别为 99.3 0 %和 99.5 4 %。     

Nafion汞膜修饰电极用于阳极溶出伏安法测定痕量铋的研究

本文报道了Nafion汞膜修饰电极及其用于阳极溶出伏安法测定未处理尿样,水样及土样中痕量铋的研究。样品中常共存的Pb(Ⅱ)、Sb(Ⅲ )等19种阳离子及尿样中共存的有机物在实验条件下不干扰。本法不仅选择性好,而且灵敏度也较高。线性范围为2×10~(-10)～1×10~(-7)mol/L。回收率为94～105％。     

Nafion修饰电极同位镀金膜阳极溶出伏安法测定痕量砷

金膜电极阳极溶出伏安法测定痕量砷已有报道,但铜、锑、铋存在严重干扰。本文采用Nafion修饰电极同位镀金膜阳极溶出伏安法测定痕量砷,大大提高了其选择性,铜、锑、铋分别为砷含量的6倍,3倍和6.5倍以下时,不干扰测定;测定灵敏度也较同位镀金膜电极时高。本法应用于标钢和黄河底泥中砷含量的测定,均获得满意结果。     

茜素紫修饰碳糊电极阳极溶出伏安法测定痕量锡

研究了利用茜素紫修饰碳糊电极测定痕量锡的阳极溶出伏安法。在 0 1 5mol/L醋酸盐缓冲溶液 (pH 4 .8)中 ,通过开路富集 ,Sn 和茜素紫形成络合物富集于电极表面 ,然后经过介质交换至 3 0mol/L的盐酸溶液中 ,于 -0 .80V还原后再进行阳极化扫描 ,于 -0 .68V左右获得一灵敏的锡的溶出峰。二次导数峰电流与Sn 浓度在 8.4× 1 0 -9～ 1 .4× 1 0 -6mol/L范围内呈良好的线性关系。检出限达 4×1 0 -9mol/L ,同时对电极反应机理进行了讨论。     

Application of a Carbon Nanotube Modified Electrode in Anodic Stripping Voltammetry for Determination of Trace Amounts of 6-Benzylaminopurine

Carbon nanotubes were modified on the surface of a glassy carbon electrode (GC) and initially applied in semi-derivative anode stripping voltammetry for the determination of 6-benzylaminopurine. The experiments demonstrated that the presence of the carbon nanotube greatly increased the current of the oxidation peak of benzylaminopurine. Cyclic voltammetry (CV) and semi-derivative voltammetry were used in a comparative investigation into the electrochemical oxidation of benzylaminopurine with the modified electrode. Studies on the effect of pH on the peak current and potential were carried out over the pH range of 9.013.0 with the NH₃–NH₄Cl buffer solution. A pH of 10.0 was chosen as the optimum pH. Other experimental parameters, such as film thickness, accumulation potential, temperature etc. were optimized. The anodic peak current was found to be linearly related to the concentration of benzylaminopurine over the range of 4.0×10^–8 to 1.0×10^–5mol·L^–1 with a detection limit of 5.0×10^–9mol·L^–1 in an accumulation time of 5min. Interferences of some inorganic and organic species on the response have been studied.     

铜膜差分脉冲阳极溶出伏安法测定药物中铋的含量

研究了铜膜电极代替汞膜电极测定重金属铋的差分脉冲溶出伏安法。实验了同位镀膜法测定铋的条件。在最佳实验条件下,Bi3+浓度在5×10-8~2×10-5mol/L范围内,其溶出峰峰高与浓度呈线性关系,检出限达到1×10-8mol/L。测定了一些药物中铋的含量,结果准确。     

High Sensitivity and Reproducibility of a Bismuth/Poly(bromocresol purple) Film Modified Glassy Carbon Electrode for Determination of Trace Amount of Cadmium by Differential Pulse Anodic Stripping Voltammetry

This work described a novel type of bismuth/poly(bromocresol purple) film modified glassy carbon electrode (denoted as Bi/Poly(BCP)/GCE) for anodic stripping analysis of trace Cd²⁺. The Bi/Poly(BCP)/GCE was fabricated in situ by depositing simultaneously bismuth and cadmium by reduction at ?1.20 V on the poly(BCP) film using a differential pulse voltammetry. Under the optimum conditions, the anodic stripping peak current response increased linearly with the Cd²⁺ concentrations in a range of 2.0×10^?8–1.0×10^?7 M and 1.0×10^?7–6.0×10^?6 M in 0.1 M NaAc‐HAc buffer solution (pH 5.0) with the detection limit of 6.5×10^?9 M (S/N=3). The Bi/poly(BCP)/GCE performed good reproducibility and high sensitivity. Finally, this proposed method was successfully applied to determine the concentration of Cd²⁺ in water samples.     

槲皮素化学修饰碳糊电极吸附溶出伏安法测定痕量铅

建立了用槲皮素修饰碳糊电极测定痕量铅的新方法 ,在 0 .1 0mol L甲酸盐缓冲液 (pH 4.3 )中 ,于 -0 .1 0V(vs.SCE)搅拌富集 ,再在 -0 .70V静止还原 40s后 ,阳极化扫描 ,于 -0 .42V左右获得一灵敏的铅阳极溶出峰。在最佳条件下 ,富集不同时间 ,其二次导数峰电流与Pb2 + 在 1 .0× 1 0 - 8～ 8.0× 1 0 - 7mol L和 2 .0× 1 0 - 9～ 6.0× 1 0 - 8mol L两个范围内呈线性关系 ,检出限为 8.0× 1 0 - 1 0 mol L(S N =3 )。同时初步探讨了电极反应机理。     

Manganese Detection with a Metal Catalyst Free Carbon Nanotube Electrode: Anodic versus Cathodic Stripping Voltammetry

Anodic stripping voltammetry (ASV) and cathodic stripping voltammetry (CSV) were used to determine Mn concentration using metal catalyst free carbon nanotube (MCFCNT) electrodes and square wave stripping voltammetry (SWSV). The MCFCNTs are synthesized using a Carbo Thermal Carbide Conversion method which results in a material that does not contain residual transition metals. Detection limits of 120 nM and 93 nM were achieved for ASV and CSV, respectively, with a deposition time of 60 s. CSV was found to be better than ASV in Mn detection in many aspects, such as limit of detection and sensitivity. The CSV method was used in pond water matrix addition measurements.     

Differential Pulse Anodic Stripping Voltammetric Determination of Lead with Heparin Modified Electrode

Introduction Overall exposure to lead is of public health concern because of several hazardous effects that may occur to human beings. Lead poisoning may provoke irritability, anorexia, malaise and headache. Intoxication progress may lead to attacks of abdominal pain until coma and death.1 The determination of trace lead in variety of en-vironmental samples is of great importance since lead is recognized as a cumulative poison to animals and hu-mans. There is a constant demand for improved an…     

金-钯双金属纳米颗粒修饰玻碳电极阳极溶出伏安法测定三价砷的方法研究

研究了金-钯双金属纳米颗粒修饰电极测定痕量砷的阳极溶出伏安法。采用紫外可见分光光度法、高分辨透射电镜及循环伏安法对颗粒的结构和电化学特性进行表征。采用方波伏安法测定三价砷,探讨了富集电位和方波伏安参数如频率、增幅、波幅以及干扰离子等对测定结果的影响。实验结果表明:金-钯双金属纳米颗粒呈壳-核结构;砷在0.30 V出现灵敏的阳极溶出伏安峰,峰电流与砷质量浓度在0.5～20μg/L范围内呈良好的线性关系,检出限为0.15μg/L;所制备的修饰电极重现性好,可用于三价砷的重复测定。共存离子Cu(Ⅱ)会影响三价砷的测定,而Pb(Ⅱ)、Cd(Ⅱ)、Zn(Ⅱ)等离子的存在对测定结果无影响。     

锆-茜素红络合物在多壁碳纳米管修饰碳糊电极上的阳极吸附伏安法研究

制备了多壁碳纳米管修饰碳糊电极并研究了锆-茜素红络合物在该电极上的阳极吸附伏安行为,采用二阶导数线性扫描伏安法进行分析,实验结果表明,在0.128 mol/L氨基乙酸-0.048 mol/L邻苯二甲酸氢钾缓冲液(pH 4.0)中,在200 mV富集60 s,在200~1200 mV范围内以200 mV/s的速率线性扫描,络合物吸附在该修饰电极表面,于832 mV(vs.SCE)处产生一个灵敏的氧化峰,为络合物中配体茜素红的氧化所产生。络合物的峰电流与锆的浓度在1.0×10-11~2.0×10-7mol/L范围内呈良好的线性关系;检出限(S/N=3)为6.0×10-12mol/L(富集时间180 s)。方法用于岩矿样品中痕量锆的测定,结果满意。     

邻苯三酚红修饰碳糊电极吸附伏安法测定痕量铋

报道了采用邻苯三酚红修饰碳糊电极测定痕量铋的方法。在０．３０ｍｏｌ／Ｌ的ＨＣｌ溶液中,于－０．１０Ｖ搅拌富集３ｍｉｎ,然后在－０．３５Ｖ静止还原６０ｓ,再进行阳极化扫描,在－０．１０Ｖ左右获得灵敏的铋溶出峰,二次导数民流与铋浓度在１．０＊１０＾－９－６．０＊１０＾－７ｍｏｌ／Ｌ范围内呈线性关系,同限为５＊１０＾－１０ｍｏｌ／Ｌ。对电极反应机理进行了讨论。